Age | Commit message (Collapse) | Author |
|
A good watchdog driver is supposed to report when it was responsible
for resetting the system. Implement this for the s3c2410, at least on
exynos5250 and exynos5420 where we already have a pointer to the PMU
registers to read the information.
Note that exynos4 SoCs also provide the reset status, but providing
that is left as an exercise for future changes and is not plumbed up
in this patch series. Also note the exynos4 SoCs don't appear to need
any PMU config, which is why this patch separates the concepts of
having PMU Registers vs. needing PMU Config.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Add device tree support for exynos5250 and 5420 SoCs and use syscon regmap interface
to configure AUTOMATIC_WDT_RESET_DISABLE and MASK_WDT_RESET_REQUEST registers of PMU
to mask/unmask enable/disable of watchdog in probe and s2r scenarios.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The existing watchdog timeout worked OK but didn't deal with
rounding in an ideal way when dividing out all of its clocks.
Specifically if you had a timeout of 32 seconds and an input clock of
66666666, you'd end up setting a timeout of 31.9998 seconds and
reporting a timeout of 31 seconds.
Specifically DBG printouts showed:
s3c2410wdt_set_heartbeat: count=16666656, timeout=32, freq=520833
s3c2410wdt_set_heartbeat: timeout=32, divisor=255, count=16666656 (0000ff4f)
and the final timeout reported to the user was:
((count / divisor) * divisor) / freq
(0xff4f * 255) / 520833 = 31 (truncated from 31.9998)
the technically "correct" value is:
(0xff4f * 255) / (66666666.0 / 128) = 31.9998
By using "DIV_ROUND_UP" we can be a little more correct.
s3c2410wdt_set_heartbeat: count=16666688, timeout=32, freq=520834
s3c2410wdt_set_heartbeat: timeout=32, divisor=255, count=16666688 (0000ff50)
and the final timeout reported to the user:
(0xff50 * 255) / 520834 = 32
the technically "correct" value is:
(0xff50 * 255) / (66666666.0 / 128) = 32.0003
We'll use a DIV_ROUND_UP to solve this, generally erroring on the side
of reporting shorter values to the user and setting the watchdog to
slightly longer than requested:
* Round input frequency up to assume watchdog is counting faster.
* Round divisions by divisor up to give us extra time.
At the same time we can avoid a for loop by just doing the right math.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
On modern SoCs the watchdog timer is parented on a clock that doesn't
change every time we have a cpufreq change. That means we don't need
to constantly adjust the watchdog timer, so avoid registering for and
dealing with cpufreq transitions unless we've actually got
CONFIG_ARM_S3C24XX_CPUFREQ defined.
Note that this is more than just an optimization. The s3c2410
watchdog driver actually pats the watchdog on every CPU frequency
change. On modern systems these happen many times per second (even in
a system where "nothing" is happening). That effectively makes any
userspace watchdog program useless (the watchdog is constantly patted
by the kernel). If we need ARM_S3C24XX_CPUFREQ defined on a
multiplatform kernel we'll need to make sure that kernel supports
common clock and change this to user common clock framework.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This patch adds a watchdog driver for devices controlled through GPIO,
(Analog Devices ADM706, Maxim MAX823, National NE555 etc).
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The keystone arch uses the same IP watchdog, so add "ti,keystone-wdt"
compatible and correct identity.
The Keystone arch is using clocks in DT and source clock for watchdog
has to be specified, so add this to binding.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Currently, the davinci watchdog can be read while counting,
so we can add ability to report the remaining time before
the system will reboot.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Some SoCs, like Keystone 2, can support more than one WDT and each
watchdog device has to use it's own base address, clock source,
watchdog device, so add new davinci_wdt_device structure to hold
device data.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Guenter roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
To reduce code duplicate and increase code readability use WDT core
code to handle WDT interface.
Remove io_lock as the WDT core uses mutex to lock each wdt device.
Remove wdt_state as the WDT core tracks state with its own variable.
The watchdog_init_timeout() can read timeout value from timeout-sec
property if the passed value is out of bounds. The heartbeat is
initialized in next way. If heartbeat is not set thought module
parameter, try to read it's value from WDT node timeout-sec property.
If node has no one, use default value.
The heartbeat is hold in wdd->timeout by WDT core, so use it in
order to set timeout period.
Davinci WDT can't be stopped and once it's expired - it can be
rearmed only after hardware reset, that's why nowayout feature
is enforced.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This change introduces debugfs support for the BCM281xx watchdog driver.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This commit adds support for the watchdog timer used on the BCM281xx
family of SoCs.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Driver was returning from link event handler without
setting linkup variable
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o __qlcnic_down call's netif_tx_disable which in turn stops
all the TX queues, corresponding start queue was missing in
__qlcnic_up which was leading to tx timeout.
o The commit b84caae486135d588fb200973b0be8cb8a511edf
(qlcnic: Fix usage of netif_tx_{wake, stop} api during link change.)
exposed this issue.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Do not re-initialize vlan list in case of adapter reset.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Bound checks should be >= instead of > for number of receive descriptors
and number of receive rings.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull ceph updates from Sage Weil:
"This is a big batch. From Ilya we have:
- rbd support for more than ~250 mapped devices (now uses same scheme
that SCSI does for device major/minor numbering)
- crush updates for new mapping behaviors (will be needed for coming
erasure coding support, among other things)
- preliminary support for tiered storage pools
There is also a big series fixing a pile cephfs bugs with clustered
MDSs from Yan Zheng, ACL support for cephfs from Guangliang Zhao, ceph
fscache improvements from Li Wang, improved behavior when we get
ENOSPC from Josh Durgin, some readv/writev improvements from
Majianpeng, and the usual mix of small cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (76 commits)
ceph: cast PAGE_SIZE to size_t in ceph_sync_write()
ceph: fix dout() compile warnings in ceph_filemap_fault()
libceph: support CEPH_FEATURE_OSD_CACHEPOOL feature
libceph: follow redirect replies from osds
libceph: rename ceph_osd_request::r_{oloc,oid} to r_base_{oloc,oid}
libceph: follow {read,write}_tier fields on osd request submission
libceph: add ceph_pg_pool_by_id()
libceph: CEPH_OSD_FLAG_* enum update
libceph: replace ceph_calc_ceph_pg() with ceph_oloc_oid_to_pg()
libceph: introduce and start using oid abstraction
libceph: rename MAX_OBJ_NAME_SIZE to CEPH_MAX_OID_NAME_LEN
libceph: move ceph_file_layout helpers to ceph_fs.h
libceph: start using oloc abstraction
libceph: dout() is missing a newline
libceph: add ceph_kv{malloc,free}() and switch to them
libceph: support CEPH_FEATURE_EXPORT_PEER
ceph: add imported caps when handling cap export message
ceph: add open export target session helper
ceph: remove exported caps when handling cap import message
ceph: handle session flush message
...
|
|
It is valid for a watchdog driver to have 0 for a "min" and "max"
timeout if the driver doesn't need the core to enforce the concepts of
min and max. The s3c2410_wdt driver is one such driver. Specifically
it can be hard for that driver to come up with a static "max" on all
platforms without a lot more information since the input clock on
S3C2410 and S3C2440 can change with DVFS.
As written, watchdog_init_timeout() will not ever read "timeout-sec"
on these drivers since watchdog_timeout_invalid() will _never_ return
true. Change to not consider a timeout_parm of 0 as valid even if
min/max aren't specified by the driver. Also handle the case when
there is no min/max and no "timeout-sec" property.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This reverts commit e120cc0dcf2880a4c5c0a6cb27b655600a1cfa1d.
It causes a NULL pointer dereference with drivers using the generic
spi_transfer_one_message(), which always calls
spi_finalize_current_message(), which zeroes master->cur_msg.
Drivers implementing transfer_one_message() theirselves must always call
spi_finalize_current_message(), even if the transfer failed:
* @transfer_one_message: the subsystem calls the driver to transfer a single
* message while queuing transfers that arrive in the meantime. When the
* driver is finished with this message, it must call
* spi_finalize_current_message() so the subsystem can issue the next
* transfer
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 patches from Martin Schwidefsky:
"A new binary interface to be able to query and modify the LPAR
scheduler weight and cap settings. Some improvements for the hvc
terminal over iucv and a couple of bux fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/hypfs: add interface for diagnose 0x304
s390: wire up sys_sched_setattr/sys_sched_getattr
s390/uapi: fix struct statfs64 definition
s390/uaccess: remove dead extern declarations, make functions static
s390/uaccess: test if current->mm is set before walking page tables
s390/zfcpdump: make zfcpdump depend on 64BIT
s390/32bit: fix cmpxchg64
s390/xpram: don't modify module parameters
s390/zcrypt: remove zcrypt kmsg documentation again
s390/hvc_iucv: Automatically assign free HVC terminal devices
s390/hvc_iucv: Display connection details through device attributes
s390/hvc_iucv: fix sparse warning
s390/vmur: Link parent CCW device during UR device creation
|
|
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64361
Cc: <stable@vger.kernel.org>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
|
|
Once we have full constraints then all supply mappings should be known to
the regulator API. This means that we should treat failed lookups as fatal
rather than deferring in the hope of further registrations but this was
broken by commit 9b92da1f1205bd25 "regulator: core: Fix default return
value for _get()" which was targeted at DT systems but unintentionally
broke non-DT systems by changing the default return value.
Fix this by explicitly returning -EPROBE_DEFER from the DT lookup if we
find a property but no corresponding regulator and by having the non-DT
case default to -ENODEV when we have full constraints.
Fixes: 9b92da1f1205bd25 "regulator: core: Fix default return value for _get()"
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
|
|
The 'offset' field of the 'scatterlist' structure was wrongly
programmed with the offset value from the base of stolen area,
whereas this field indicates the offset from where the interested
data starts within the first PAGE pointed to by 'scattterlist'
structure. As a result when a new GEM object allocated from stolen
area is mapped to GTT, it could lead to an overwrite of GTT entries
as the page count calculation will go wrong, refer the function
'sg_page_count'.
v2: Modified the commit message. (Chris)
Signed-off-by: Akash Goel <akash.goel@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=71908
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69104
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The buffer pointer passed from the upper layer may points to
a buffer in the stack or a buffer allocated by vmalloc, and etc..
This patch adds more sanity check to this buffer.
After this patch, if we meet a buffer which is allocated by vmalloc or
a buffer in the stack, we will use our own DMA buffer @data_buffer_dma
to do the DMA operations. If the buffer is not the cases above, we will
map it for DMA operations directly.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
The @data_buffer_dma buffer is used for non ECC read/write.
Currently, the length of the buffer is PAGE_SIZE, but the NAND chip may
has 8K page or 16K page. So we have to extend it for the large page NAND
chips.
The gpmi_alloc_dma_buffer will be called twice. The first time is to
allocate a temporary buffer for scanning the NAND chip; The second time
is to allocate a buffer to store the real page content.
This patch allocates a buffer of PAGE_SIZE size for scanning the NAND
chip when gpmi_alloc_dma_buffer is called the first time, and allocates a
buffer of the real NAND page size for the second time gpmi_alloc_dma_buffer
is called.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
When using the Quad Read opcode, SPI masters still use Single SPI
transfers, as spi_transfer.rx_nbits defaults to SPI_NBITS_SINGLE.
Use SPI_NBITS_QUAD to fix this.
While an earlier version of commit 3487a63955c34ea508bcf4ca5131ddd953876e2d
("drivers: mtd: m25p80: add quad read support") did this correctly, it was
forgotten in the version that got merged.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Spansion s25fl512s supports Quad SPI transfers, hence set the
M25P80_QUAD_READ flag.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Merge misc updates from Andrew Morton:
- a few hotfixes
- dynamic-debug updates
- ipc updates
- various other sweepings off the factory floor
* akpm: (31 commits)
firmware/google: drop 'select EFI' to avoid recursive dependency
compat: fix sys_fanotify_mark
checkpatch.pl: check for function declarations without arguments
mm/migrate.c: fix setting of cpupid on page migration twice against normal page
softirq: use const char * const for softirq_to_name, whitespace neatening
softirq: convert printks to pr_<level>
softirq: use ffs() in __do_softirq()
kernel/kexec.c: use vscnprintf() instead of vsnprintf() in vmcoreinfo_append_str()
splice: fix unexpected size truncation
ipc: fix compat msgrcv with negative msgtyp
ipc,msg: document barriers
ipc: delete seq_max field in struct ipc_ids
ipc: simplify sysvipc_proc_open() return
ipc: remove useless return statement
ipc: remove braces for single statements
ipc: standardize code comments
ipc: whitespace cleanup
ipc: change kern_ipc_perm.deleted type to bool
ipc: introduce ipc_valid_object() helper to sort out IPC_RMID races
ipc/sem.c: avoid overflow of semop undo (semadj) value
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc updates from Ben Herrenschmidt:
"So here's my next branch for powerpc. A bit late as I was on vacation
last week. It's mostly the same stuff that was in next already, I
just added two patches today which are the wiring up of lockref for
powerpc, which for some reason fell through the cracks last time and
is trivial.
The highlights are, in addition to a bunch of bug fixes:
- Reworked Machine Check handling on kernels running without a
hypervisor (or acting as a hypervisor). Provides hooks to handle
some errors in real mode such as TLB errors, handle SLB errors,
etc...
- Support for retrieving memory error information from the service
processor on IBM servers running without a hypervisor and routing
them to the memory poison infrastructure.
- _PAGE_NUMA support on server processors
- 32-bit BookE relocatable kernel support
- FSL e6500 hardware tablewalk support
- A bunch of new/revived board support
- FSL e6500 deeper idle states and altivec powerdown support
You'll notice a generic mm change here, it has been acked by the
relevant authorities and is a pre-req for our _PAGE_NUMA support"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (121 commits)
powerpc: Implement arch_spin_is_locked() using arch_spin_value_unlocked()
powerpc: Add support for the optimised lockref implementation
powerpc/powernv: Call OPAL sync before kexec'ing
powerpc/eeh: Escalate error on non-existing PE
powerpc/eeh: Handle multiple EEH errors
powerpc: Fix transactional FP/VMX/VSX unavailable handlers
powerpc: Don't corrupt transactional state when using FP/VMX in kernel
powerpc: Reclaim two unused thread_info flag bits
powerpc: Fix races with irq_work
Move precessing of MCE queued event out from syscall exit path.
pseries/cpuidle: Remove redundant call to ppc64_runlatch_off() in cpu idle routines
powerpc: Make add_system_ram_resources() __init
powerpc: add SATA_MV to ppc64_defconfig
powerpc/powernv: Increase candidate fw image size
powerpc: Add debug checks to catch invalid cpu-to-node mappings
powerpc: Fix the setup of CPU-to-Node mappings during CPU online
powerpc/iommu: Don't detach device without IOMMU group
powerpc/eeh: Hotplug improvement
powerpc/eeh: Call opal_pci_reinit() on powernv for restoring config space
powerpc/eeh: Add restore_config operation
...
|
|
The GOOGLE_SMI Kconfig symbol depends on DMI and selects EFI. This
causes problems on other archs when introducing DMI support that depends
on EFI, as it results in a recursive dependency:
arch/arm/Kconfig:1845:error: recursive dependency detected!
arch/arm/Kconfig:1845: symbol DMI depends on EFI
Fix by changing the 'select EFI' to a 'depends on EFI'.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: David Rientjes <rientjes@google.com>
Acked-by: Mike Waychison <mikew@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Indentation mismatch spotted with Coverity.
Introduced in 4e3b35b044ea ("i40e: add DCB and DCBNL support")
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes grant transfer releasing code from netfront, and uses
gnttab_end_foreign_access to end grant access since
gnttab_end_foreign_access_ref may fail when the grant entry is
currently used for reading or writing.
* clean up grant transfer code kept from old netfront(2.6.18) which grants
pages for access/map and transfer. But grant transfer is deprecated in current
netfront, so remove corresponding release code for transfer.
* fix resource leak, release grant access (through gnttab_end_foreign_access)
and skb for tx/rx path, use get_page to ensure page is released when grant
access is completed successfully.
Xen-blkfront/xen-tpmfront/xen-pcifront also have similar issue, but patches
for them will be created separately.
V6: Correct subject line and commit message.
V5: Remove unecessary change in xennet_end_access.
V4: Revert put_page in gnttab_end_foreign_access, and keep netfront change in
single patch.
V3: Changes as suggestion from David Vrabel, ensure pages are not freed untill
grant acess is ended.
V2: Improve patch comments.
Signed-off-by: Annie Li <annie.li@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Export the symbol so that it is accessible to modules.
Fixes the following error:
ERROR: "pl08x_filter_id" [sound/soc/samsung/snd-soc-s3c-dma.ko] undefined!
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The contents of this header file is not referenced in the led driver.
Remove its inclusion. While at it, re-arrange the headers as per the
category.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Use the more convenient macro.
Signed-off-by: ZHAO Gang <gamerh2o@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This removes a warning on non-DT-enabled platforms:
drivers/leds/leds-pwm.c: In function 'led_pwm_create_of':
drivers/leds/leds-pwm.c:88:22: warning: unused variable 'node'
Really caused by the local variable that is assigned to and then never
used. Just do away with the local var, it's not needed.
Technically this code path can never be entered without DT enabled,
since there's an earlier check about number of children in the calling
function, but the compiler can't see that.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Overflow maybe occurs when calculates the duty time. For instance,
the period time is 990000000ns, and the max_brightness is 127, when
setting the brightness to 12, the duty value will be 25906026ns, but
it should be 93543307ns.
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
LED registers are used only in this driver, so no additional
locking is needed. Read-Modify-Write cycle in workqueue is already
protected by regmap.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
LED platform data are overwhelmed by excessive field "max_cur"
which just replicates few bits of "led_control" field.
This patch removes this field and adds a definition for the
current settings in the header.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
'gpio_base'
Need check CONFIG_GPIOLIB whether defined, just like another area has
done within this file. Or can not pass compiling when CONFIG_GPIOLIB
disabled.
The related error (with allmodconfig for metag):
CC [M] drivers/leds/leds-tca6507.o
drivers/leds/leds-tca6507.c: In function 'tca6507_led_dt_init':
drivers/leds/leds-tca6507.c:731: error: 'struct tca6507_platform_data' has no member named 'gpio_base'
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
There are two ways to run a pattern in LP5523.
One is using legacy sysfs files such as 'enginex_mode','enginex_load' and
'enginex_leds'. ('x' is from 1 to 3).
Among them, 'enginex_leds' are used for selecting specific LED channel MUX.
(MUX means which LEDs are used for running a pattern from LED 1 to 9.)
The other way is using the firmware interface.
In this mode, the default LED MUX strings are used.
In other words, LED MUX is not configurable on the fly.
This patch enables dynamic LED MUX configuration when the firmware is loaded.
By accessing the sysfs file 'enginex_leds', the LED channels can be configured.
To synchronize the operation mode, each engine mode should be set to 'LOAD'.
The documentation is updated as well.
Cc: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Whenever the engine is loaded by the user-application, the operation mode is
reset first. But it has a problem in case of multiple engine used because
previous engine settings are cleared.
The driver should update not whole 8bits but each engine bit by masking.
On the other hands, whole engines should be reset when the driver is unloaded
and on initializing the LP5523 driver.
So, new functions are used for this handling - lp5521/5523_stop_all_engines().
Cc: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
In particular fix the capitalisation of GPIO and LED and
correct TCA6507_MAKE_CPIO, but also rewrite the comment about
platform-data to include reference to devicetree.
Also re-wrap comments to fit 80 columns.
Reported-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
The 7 lines driven by the TCA6507 can either drive LEDs or act as output-only
GPIOs.
To make this distinction in devicetree we use the "compatible" property.
If the device attached to a line is "compatible" with "gpio", we treat it
like a GPIO. If it is "compatible" with "led" (or if no "compatible" value
is set) we treat it like an LED.
(cooloney@gmail.com: fix typo in the subject)
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
1/ The led_info array must be allocated to allow the full number
of LEDs even if not all are present. The array maybe be sparsely
filled but it is indexed by device address so we must at least
allocate as many slots as the highest address used. It is easiest
just to allocate all 7.
2/ range check the 'reg' value properly.
3/ led.flags must be initialised to zero, else all leds could
be treated as GPIOs (depending on what happens to be on the stack).
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
On larger systems with many drives, it may help debugging to know which
queue is tied to which interrupt, just by looking at /proc/interrupts.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
|
We need to shut down the device cleanly when the system is being shut down.
This was in an earlier patch but was inadvertently lost during a rewrite.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
|
Disable the admin queue if device fails during initialization so the
queue's irq is freed.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[rewritten to use nvme_free_queues]
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
|
Some users need more than 64 partitions per device. Rather than simply
increasing the number of partitions, switch to the dynamic partition
allocation scheme.
This means that minor numbers are not stable across boots, but since major
numbers aren't either, I cannot see this being a significant problem.
Tested-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|
|
This attempts to delete all IO queues at the same time asynchronously on
shutdown. This is necessary for a present device that is not responding;
a shutdown operation previously would take 2 minutes per queue-pair
to timeout before moving on to the next queue, making a device removal
appear to take a very long time or "hung" as reported by users.
In the previous worst case, a removal may be stuck forever until a kill
signal is given if there are more than 32 queue pairs since it would run
out of admin command IDs after over an hour of timed out sync commands
(admin queue depth is 64).
This patch will wait for the admin command timeout for all commands to
complete, so the worst case now for an unresponsive controller is 60
seconds, though that still seems like a long time.
Since this adds another way to take queues offline, some duplicate code
resulted so I moved these into more convienient functions.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[make functions static, correct line length and whitespace issues]
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
|