| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xHCI: USB 2.0 Link PM and misc cleanup patches
Hi Greg,
Here's six patches to be queued for 3.11.
The first four add support for a new type of host hardware-managed USB
2.0 Link Power Management. Hosts with BESL support, including Intel
Haswell ULT systems, will now be able to have USB 2.0 devices go into
the lower power link state (L1) in between packets. These patches have
been tested on Haswell ULT platforms with USB 2.0 webcams that support
Link PM.
The other two patches are clean up. One from Julius clarifies the xHCI
endpoint context debugging to make it consistent with standard endpoint
addresses, instead of xHCI endpoint context indexes. The one from Alex
changes the xHCI driver to be consistent about passing a void pointer to
the xHCI IRQ handler.
Sarah Sharp
|
|
No action is needed for the HWA_NOTIF_BPST_ADJ event. Ignore it instead
of printing a warning to the log since these events can happen dozens of
times per second.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds support for the Alereon 5310 and 5611 devices to the
HWA-rc driver.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds the HWA specific members to struct usb_rpipe_descriptor
and sets them correctly based on the wireless endpoint compananion
descriptor.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Suspend and resume are not currently supported on the wireless root hub.
Remove the suspend and resume op functions in the host controller driver
to avoid constant error messages in the system log.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a misprint in init_usb_class():
IS_ERR is used to get error code instead of PTR_ERR.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch reduces the keepalive threshold of WUSB host controllers from
timeout/2 to timeout/3. The keepalive timer fires every timeout/2 ms, but
due to rounding errors and jitter, the host may decide not to send a
keepalive at timeout/2. By the time the next timer fires, a full timeout
period may have expired causing the device to be disconnected without ever
having been sent a keepalive. Changing the keepalive threshold to
timeout/3 ensures that at least one keepalive will be sent before a device
is disconnected. The patch also updates the code to use msecs_to_jiffies
consistently.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The three options USB_ARCH_HAS_{EHCI,OHCI,XHCI} are all well beyond
their recommended shelf life. They have caused numerous build failures
over the years because they are never completely correct, and with
the move to splitting out the platform specific back-ends out of the
driver, there is no real need for them any more. Also, the use of making
USB_ARCH_HAS_HCD depend on it is questionable since one can always enable
dummy_hc these days.
This patch enables them unconditionally for all platforms and
architectures, which means it is now possible to build host controller
drivers for machines that are known not to come with this hardware,
but that is just how we treat most other drivers.
In order to minimise the impact on existing architecture code and
defconfig files, all the Kconfig are left present for now. All platforms
that currently do 'select USB_ARCH_HAS_*' should subsequently be changed
not to select that. All drivers depending on USB_ARCH_HAS_HCD should
be changed to depend on USB_SUPPORT instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The OHCI host controller driver can be built standalone now,
without enabling any of the available bus glue drivers, so
there is not really a reason to error out here:
drivers/usb/host/ohci-hcd.c:1258: error:
#error "missing bus glue for ohci-hcd" #error "missing bus glue for ohci-hcd"
This follows the same change done in ehci recently as 843e56c0
"USB: EHCI: remove bogus #error" and hopefully avoids future
merge conflicts in this list.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adds abitilty to tune L1 timeout (inactivity timer for usb2 link sleep)
and BESL (best effort service latency)via sysfs.
This also adds a new usb2_lpm_parameters structure with those variables to
struct usb_device.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
usb 2.0 devices with link power managment (LPM) can describe their idle link
timeouts either in BESL or HIRD format, so far xHCI has only supported HIRD but
later xHCI errata add BESL support as well
BESL timeouts need to inform exit latency changes with an evaluate
context command the same way USB 3.0 link PM code does.
The same xhci_change_max_exit_latency() function is used as with USB3
but code is pulled out from #ifdef CONFIG_PM as USB2.0 BESL LPM
funcionality does not depend on CONFIG_PM.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
Hardware link powermanagement in usb2 is a per-port capability.
Previously support for hw lpm was enabled for all ports if any usb2 port supported it.
Now instead cache the capability values and check them for each port individually
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
According to Felipe and Alan's comments the second parameter of irq
handler should be 'void *' not a specific structure pointer.
So change it.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
When CONFIG_XHCI_HCD_DEBUGGING is activated, the XHCI driver can dump
device and input contexts to the console. The endpoint contexts in that
dump are labeled "Endpoint N Context", where N is the XHCI endpoint
index (DCI - 1). This can be very confusing, especially for people who
are not that familiar with the XHCI specification. This patch introduces
an xhci_get_endpoint_address function (as a counterpart to the reverse
xhci_get_endpoint_index), and uses it to additionally display the
endpoint number and direction when dumping contexts, which are much more
commonly used concepts in USB.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
My PL2303HX works at 500kbps after applying this patch.
I suppose that it could work at other non standard speeds since this fix
"correctly handle baudrates above 115200"
https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/drivers/usb/serial/pl2303.c?id=8d48fdf689fed2c73c493e5146d1463689246442
came after this one
"fix baud rate handling in case of unsupported values"
https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/drivers/usb/serial/pl2303.c?id=25b8286805e856c8c7fda127018e31032c918015
but I only can test it with 500000.
Patch made against mainline but tested with 3.4.45
Signed-off-by: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In kernel we have nice specifier %*ph to dump small buffers. Let's use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds an ohci->priv field for private use by OHCI
platform drivers.
Until now none of the platform drivers has used this private space,
but that's about to change in the next patch of this series.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch splits the ohci-platform code from ohci-hcd out
into its own separate driver module.This work is part of enabling
multi-platform kernels on ARM.
In V2:
-Passed "hcd" argument instead of "ohci" in ohci_setup() because it is
using "struct usb_hcd" argument.
In V3:
-Directly passed "hcd" argument not required to call ohci_to_hcd() function.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pci_enable_device() will set device power state to D0,
so it's no need to do it again in ci13xxx_pci_probe().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The usb3503 driver sleeps a flat 100ms when resetting the chip, with a
comment about waiting for the reference clock. This seems to be a
board-specific detail that should not hold up boot across all platforms.
This patch reduces the sleep to the 4ms initialization delay that the
chip itself actually requires (as per its data sheet). If certain boards
require more time to set up the reference clock, they should change this
through local patches or add a proper, configurable synchronization
mechanism.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove an erroneous tab that should be a space.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds Wireless USB root hub support to the USB HCD. It allows
the HWA to create its root hub which previously failed because the HCD
treated wireless root hubs the same as USB2 high speed hubs. The creation
of the root hub would fail in that case due to lack of TTs which wireless
root hubs do not support.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove redundant "_fusbh200_" from fusbh200_hcd_fusbh200_probe
and fusbh200_hcd_fusbh200_remove
Signed-off-by: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If you want to download Infineon modem via USB, this Infineon USB
flashloader driver is required.
Signed-off-by: Wei Shuai <cpuwolf@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch splits the PCI portion of ohci-hcd out into its
own separate driver module, called ohci-pci.
The major point of difficulty lies in ohci-pci's many vendor- and
device-specific workarounds. Some of them have to be applied before
calling ohci_start() some after, which necessitates a fair amount of
code motion. The other platform drivers require much smaller changes.
The complete sb800_prefetch() function moved to ohci-q.c,because its
only related to ohci-pci driver.
USB_OHCI_HCD_PCI symbol no longer dependence on STB03xxx, PPC_MPC52xx and
USB_OHCI_HCD_PPC_OF that's what removed.
V2:
- few specific content of pci related code in ohci_pci_start function has been moved to ohci_pci_reset
and rest of the generic code is written in ohci_start of ohci-hcd.c file.
V3:
- ohci_restart() has been called in ohci_pci_reset() function for to reset the ohci pci.
V4:
-sb800_prefetch() moved to ohci-q.c,because its only related to ohci-pci.
-no longer _creating_ CONFIG_USB_OHCI_PCI,creating CONFIG_USB_OHCI_HCD_PCI.
-overrides renamed with pci_override,its giving proper meaning.
V5:
-sb800_prefetch() moved to pci-quirks.c,because its only related to pci.
V6:
-sb800_prefetch() function has been moved to pci-quirks.c made as separate patch in 2/3.
-Most of the generic ohci pci changes moved in 2/3 patch,now this is complete ohci-pci separation patch.
V7:
-Unrelated include file has been removed from ohci.h file.
V8:
-USB_OHCI_HCD_PCI symbol does not dependence on STB03xxx, PPC_MPC52xx and USB_OHCI_HCD_PPC_OF.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Note that this changes is part of separating the ohci pci host controller
driver from ohci-hcd host code.
This contains :
-Moved sb800_prefetch() function from ohci-pci.c to pci-quirks.c file
and EXPORTed, this is part of the effort to move the ohci pci related
code to generic pci code.
-Passed "device" argument instead of "ohci_hcd" in sb800_prefetch()
function to avoid extra include file in pci-quirks.c.
V2:
-Passed "device" argment instead of "pci_dev", then we use to_pci_dev()
to get the "pci_dev" structure.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch prepares ohci-hcd for being split up into a core
library and separate platform driver modules. A generic
ohci_hc_driver structure is created, containing all the "standard"
values, and a new mechanism is added whereby a driver module can
specify a set of overrides to those values. In addition the
ohci_restart(),ohci_suspend() and ohci_resume() routines need
to be EXPORTed for use by the drivers.
Added ohci_setip(() and ohci_start() routine for to start the generic
controller rather than each having its own idiosyncratic approach.
This allow to clean duplicated code in most of SOC driver
In V2:
-ohci_hcd_init() ohci_run() and ohci_stop() are not made non-static.
-Adds the ohci_setup() and ohci_start() routine.
In V3:
-purpose of ohci_setup() and ohci_start() function description written in the patch
description.
-ohci_init() are not made non-static but now called beginning of the ohci_restart().
-ohci_run() signature change reverted back.
-unrelated changes removed.
-duplicate comment line removed.
-inline ohci_suspend() and ohci_resume() is not needed so removed from ohci.h file.
In V4:
-ohci-init() EXPORTed because it is called by all bus glue modules.
-ohci-setup() removed from 1/2 added into 2/2 patch.
In V5:
-Again ohci_setup() is added and EXPORTed because to replace the ohci_init() from
all bus glues.
-ohci_init() is not made non-static function.
In V6:
-ohci_init() call is removed from ohci_quirk_nec_worker(), because it is already called in ohci_restart().
In V8:
-ohci_hcd_init() is called by ohci_setup() to make generic ohci initialization in all ohci drivers.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch attempts to fix the isochronous API in the fhci-hcd
driver. There are two problems with the current code:
ed->last_iso is used but not set anywhere. The patch changes
its name to ed->next_iso and uses it to store the frame number
of the next available slot in the isochronous stream.
urb->start_frame isn't set when the URB_ISO_ASAP flag is off.
The patch sets it to the next available slot if the stream is
in use, or the current frame otherwise.
This won't give the right behavior when an underrun occurs, but I
don't know enough about the driver to handle that case.
Unfortunately, I don't have any way to test these changes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Anton Vorontsov <avorontsov@ru.mvista.com>
CC: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch attempts to update the imx21-hcd driver to the current
standard for the isochronous API. Firstly, urb->start_frame should
always be set by the driver; it is not an input parameter. Secondly,
the URB_ISO_ASAP flag matters only when an URB is submitted to a
stream that has gotten an underrun. It causes the URB to be scheduled
for the next available slot in the future, rather than the earliest
unused (and expired) slot.
Unfortunately, I don't have any way to test these changes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch attempts to fix the isochonour API in the musb host
driver. In particular, the urb->start_frame field should always be
set by the driver; it isn't an input parameter.
The simplest way to accomplish this is to treat all URBs as though the
URB_ISO_ASAP flag was set. This won't give the right behavior when an
underrun occurs, but I don't know enough about the musb driver to
handle that case.
Unfortunately, I have no way to test this change.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Exynos5440 does not require any explict USB phy configuration. So skip
the USB phy configuration for Exynos5440 based platforms.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Ackked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a specifier we may use to dump small buffers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
'hcd' can never be NULL and the spear_ehci_hcd_drv_remove routine
will never be called in_interrupt. Hence remove these checks.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When converting this driver to devm_ioremap_resource, the removal of this now
unneeded function has been forgotten.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch is to add a property 'disabled-ports' representing the unused port
of USB3503. USB3503 can support up to 3 USB host port and each ports can be
controlled to be enabled or disabled. Do not describe this property if all
ports must be enabled.
You can represent the ports to disable in the device tree.
usb3503@08{
...
disabled-ports = <2 3>;
...
};
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch is to disable the USB ports unconnected to USB3503. In order to
disable the port, 'port_off_mask' must be set.
* Disable PORT1 only
.port_off_mask = USB3503_OFF_PORT1;
* Disable PORT1 and PORT3 only
.port_off_mask = USB3503_OFF_PORT1 | USB3503_OFF_PORT3;
* Enables all ports
.port_off_mask = 0;
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want these fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull amd64 edac fix from Borislav Petkov:
"A sysfs file permissions correction"
* tag 'edac_fixes_for_3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
amd64_edac: Fix bogus sysfs file permissions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"This time we made the kernel- and interruption stack allocation
reentrant which fixed some strange kernel crashes (specifically
protection ID traps).
Furthemore this patchset fixes the interrupt stack in UP and SMP
configurations by using native locking instructions. And finally
usage of floating point calculations on parisc were disabled in the
MPILIB."
* 'parisc-for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix irq stack on UP and SMP
parisc/superio: Use module_pci_driver to register driver
parisc: make interrupt and interruption stack allocation reentrant
parisc: show number of FPE and unaligned access handler calls in /proc/interrupts
parisc: add additional parisc git tree to MAINTAINERS file
parisc: use PAGE_SHIFT instead of hardcoded value 12 in pacache.S
parisc: add rp5470 entry to machine database
MPILIB: disable usage of floating point registers on parisc
|
|
Pull bettery fixes from Anton Vorontsov:
"Last minute one-liners: wrong kfree usage fix, module alias fixup and
kconfig adjustments"
* tag 'for-v3.10-fixes' of git://git.infradead.org/battery-2.6:
pm2301_charger: Fix module alias prefix
wm831x_backup: Fix wrong kfree call for devdata->backup.name
bq27x00: Fix I2C dependency in KConfig
lp8788-charger: Fix kconfig dependency
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
- Additional CPU ID for the intel_pstate driver from Dirk Brandewie.
- More cpufreq fixes related to ARM big.LITTLE support and locking from
Viresh Kumar.
- VIA C7 cpufreq build fix from Rafał Bilski.
- ACPI power management fix making it possible to use device power
states regardless of the CONFIG_PM setting from Rafael J Wysocki.
- New ACPI video blacklist item from Bastian Triller.
* tag 'pm+acpi-3.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: Add "Asus UL30A" to ACPI video detect blacklist
cpufreq: arm_big_little_dt: Instantiate as platform_driver
cpufreq: arm_big_little_dt: Register driver only if DT has valid data
cpufreq / e_powersaver: Fix linker error when ACPI processor is a module
cpufreq / intel_pstate: Add additional supported CPU ID
cpufreq: Drop rwsem lock around CPUFREQ_GOV_POLICY_EXIT
ACPI / PM: Allow device power states to be used for CONFIG_PM unset
|
|
Pull slave-dma fixes from Vinod Koul:
"We have two patches from Andy & Rafael fixing the Lynxpoint dma"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
ACPI / LPSS: register clock device for Lynxpoint DMA properly
dma: acpi-dma: parse CSRT to extract additional resources
|
|
Merge fixes from Andrew Morton:
"A bunch of fixes and one simple fbdev driver which missed the merge
window because people will still talking about it (to no great
effect)."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (30 commits)
aio: fix kioctx not being freed after cancellation at exit time
mm/pagewalk.c: walk_page_range should avoid VM_PFNMAP areas
drivers/rtc/rtc-max8998.c: check for pdata presence before dereferencing
ocfs2: goto out_unlock if ocfs2_get_clusters_nocache() failed in ocfs2_fiemap()
random: fix accounting race condition with lockless irq entropy_count update
drivers/char/random.c: fix priming of last_data
mm/memory_hotplug.c: fix printk format warnings
nilfs2: fix issue of nilfs_set_page_dirty() for page at EOF boundary
drivers/block/brd.c: fix brd_lookup_page() race
fbdev: FB_GOLDFISH should depend on HAS_DMA
drivers/rtc/rtc-pl031.c: pass correct pointer to free_irq()
auditfilter.c: fix kernel-doc warnings
aio: fix io_getevents documentation
revert "selftest: add simple test for soft-dirty bit"
drivers/leds/leds-ot200.c: fix error caused by shifted mask
mm/THP: use pmd_populate() to update the pmd with pgtable_t pointer
linux/kernel.h: fix kernel-doc warning
mm compaction: fix of improper cache flush in migration code
rapidio/tsi721: fix bug in MSI interrupt handling
hfs: avoid crash in hfs_bnode_create
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We didn't have any fixes sent up for -rc2, so this is a slightly
larger batch. A bit all over the place platform-wise; OMAP, at91,
marvell, renesas, sunxi, ux500, etc.
I tried to summarize highlights but there isn't a whole lot to point
out. Lots of little things fixed all over. A couple of defconfig
updates due to new/changing options."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: at91/sama5: fix incorrect PMC pcr div definition
ARM: at91/dt: fix macb pinctrl_macb_rmii_mii_alt definition
ARM: at91: at91sam9n12: move external irq declatation to DT
ARM: shmobile: marzen: Use error values in usb_power_*
ARM: tegra: defconfig fixes
ARM: nomadik: fix IRQ assignment for SMC ethernet
ARM: vt8500: Add missing NULL terminator in dt_compat
clk: tegra: add ac97 controller clock
clk: tegra: remove USB from clk init table
ARM: dts: mvebu: Fix wrong the address reg value for the L2-cache node
ARM: plat-orion: Fix num_resources and id for ge10 and ge11
ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apis
SERIAL: OMAP: Remove the slave idle handling from the driver
ARM: OMAP2+: serial: Remove the un-used slave idle hooks
ARM: OMAP2+: hwmod-data: UART IP needs software control to manage sidle modes
ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in active
ARM: OMAP2+: hwmod: Fix sidle programming in _enable_sysc()/_idle_sysc()
arm: mvebu: fix the 'ranges' property to handle PCIe
ARM: mvebu: select ARCH_REQUIRE_GPIOLIB for mvebu platform
ARM: AM33XX: Add missing .clkdm_name to clkdiv32k_ick clock
...
|
|
Currently the driver can crash with a NULL pointer dereference if no
pdata is provided, despite of successful registration of the MFD part.
This patch fixes the problem by adding a NULL check before dereferencing
the pdata pointer.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 902c098a3663 ("random: use lockless techniques in the interrupt
path") turned IRQ path from being spinlock protected into lockless
cmpxchg-retry update.
That commit removed r->lock serialization between crediting entropy bits
from IRQ context and accounting when extracting entropy on userspace
read path, but didn't turn the r->entropy_count reads/updates in
account() to use cmpxchg as well.
It has been observed, that under certain circumstances this leads to
read() on /dev/urandom to return 0 (EOF), as r->entropy_count gets
corrupted and becomes negative, which in turn results in propagating 0
all the way from account() to the actual read() call.
Convert the accounting code to be the proper lockless counterpart of
what has been partially done by 902c098a3663.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit ec8f02da9ea5 ("random: prime last_data value per fips
requirements") added priming of last_data per fips requirements.
Unfortuantely, it did so in a way that can lead to multiple threads all
incrementing nbytes, but only one actually doing anything with the extra
data, which leads to some fun random corruption and panics.
The fix is to simply do everything needed to prime last_data in a single
shot, so there's no window for multiple cpus to increment nbytes -- in
fact, we won't even increment or decrement nbytes anymore, we'll just
extract the needed EXTRACT_SIZE one time per pool and then carry on with
the normal routine.
All these changes have been tested across multiple hosts and
architectures where panics were previously encoutered. The code changes
are are strictly limited to areas only touched when when booted in fips
mode.
This change should also go into 3.8-stable, to make the myriads of fips
users on 3.8.x happy.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stodola <jstodola@redhat.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Matt Mackall <mpm@selenic.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The index on the page must be set before it is inserted in the radix
tree. Otherwise there is a small race which can occur during lookup
where the page can be found with the incorrect index. This will trigger
the BUG_ON() in brd_lookup_page().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reported-by: Chris Wedgwood <cw@f00f.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
