summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)Author
2011-04-11niu: Recognise original ethtool class code for AH/ESP flow hashingBen Hutchings
When the RX network flow classification interface was originally defined for reporting and controlling of flow hashing, AH and ESP were not given distinct flow class codes (apparently because the Sun Neptune hardware treats them very similarly). For flow steering, they must be distinguished, so new and separate flow class codes were added for AH and ESP. But for backward- compatibility, flow hash operations should continue to support the original class codes. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-11gianfar: Clean up implementation of RX network flow classificationBen Hutchings
This code was cribbed from niu, so gfar_set_hash_opts() begins by converting the ethtool flow class code into a class code for Sun Neptune hardware, then does the same thing again for the hardware it's really dealing with. It may also return -1 (-EPERM) for some unhandled ethtool flow class codes. Remove the useless code and definitions, and fix the error code. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-11qlge: use ethtool set_phys_idstephen hemminger
This is a stab at replacing old ethtool phys_id with set_phys_id on the Qlogic 10Gb driver. Compile tested only. Not sure if set_led_cfg will flash continuously, or needs to be replaced by ETHTOOL_ID_ON/ETHTOOL_ID_OFF Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-10net: bnx2: convert to hw_featuresMichał Mirosław
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-10net: via-velocity: convert to hw_featuresMichał Mirosław
Trivial conversion. This also enables toggling TX VLAN offload and fixes TX checksumming race with offload changes. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-10net: ksz884x: convert to hw_featuresMichał Mirosław
This also fixes possible race when changing receive checksum state and removes IPV6_CSUM_GEN_HACK as it's always set. BTW, The claim about fake IPV6 checksum looks dubious. If that were true, then there's a problem in networking core and should be fixed there and not in random drivers. BTW#2, there's no MAINTAINERS entry for this driver. I assume this driver is supported by Micrel? Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-10net: stmmac: convert to hw_featuresMichał Mirosław
This also removes TSO as it's made fully in software --- better to leave this to networking core. If the MAC features can be detected at probe time and not at open, then stmmac_fix_features could be simplified by limiting hw_features. That's also better for users as they don't see offloads being togglable but never turned on. Redundant fallbacks for TX csum are removed as it's already handled by network core. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-10net: 8139cp: convert to hw_featuresMichał Mirosław
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-10net: r8169: convert to hw_featuresMichał Mirosław
Simple conversion with a bit of needed cleanup. This also fixes: - confusion around vlan_features in rtl8169_vlan_mode(), - problem with broken TSO for too big MTU (the limit is set at 0xFFF --- max MSS field value). SG+IP_CSUM+TSO is left disabled by default, based on suggestion by David Dillow. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-10net: benet: convert to hw_features - fixupMichał Mirosław
Fix up after merge with NETIF_F_RXHASH implementation. This allows to toggle NETIF_F_RXHASH and NETIF_F_HW_VLAN_TX. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-10net: Remove invalid offloadsMichał Mirosław
Remove offload changing ethtool ops which drivers don't really support: - fs_enet - ucc_geth Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-10usb: plusb: Add debug to reset functionsimon
This patch adds some debug to the reset function to print out the reason why it fails. Signed-off-by: Simon Wood <simon@mungewell.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-10usb: plusb: Add support for PL-25A1simon
This patch adds support for the PL-25A1 by adding the appropriate USB ID's. This chip is used in the Belkin 'Windows Easy Transfer' Cables. Signed-off-by: Simon Wood <simon@mungewell.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-10usb: plusb: Whitespacesimon
This patch cleans up a couple of instances of incorrect whitespace Signed-off-by: Simon Wood <simon@mungewell.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-08cxgb4vf: drop phys_id interface and implement the newer set_phys_idDimitris Michailidis
Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-08cxgb4: drop phys_id interface and implement the newer set_phys_idDimitris Michailidis
Signed-off-by: Dimitris Michailidis <dm@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-08cnic: Fix rtnl deadlockMichael Chan
When cnic_stop_hw() -> cnic_cm_stop_bnx2x_hw() is called under rtnl_lock() from NETDEV_DOWN event, it waits for cnic_delete_task() to complete. It will deadlock when cnic_delete_task() takes rtnl_lock() before calling cnic_ulp_stop_one(). We fix it by removing the rtnl_lock() in cnic_delete_task(). cnic_ulp_stop_one() has mutex and atomic bit ops to prevent important operations from being done more than once, so it is not necessary to take rtnl_lock(). Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-07net: atl*: convert to hw_featuresMichał Mirosław
Things left as they were: - atl1: is RX checksum really enabled? - atl2: copy-paste from atl1, with-errors-on-modify I presume - atl1c: there's a bug: MTU can't be changed if device is not up Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-07net: tg3: convert to hw_featuresMichał Mirosław
Cleanup hint: Some features are calculated in tg3_get_invariants() and the rest in its caller --- tg3_init_one(). This is not changed here. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-07net: enic: convert to hw_featuresMichał Mirosław
As the driver uses GRO and not LRO, LRO settings are ignored anyway and are removed here to avoid confusion. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-07net: benet: convert to hw_featuresMichał Mirosław
Simple conversion. This also fixes a bug in TX checksum toggling --- driver was changing NETIF_F_HW_CSUM instead of NETIF_F_IP_CSUM+NETIF_F_IPV6_CSUM. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-07skge: convert to hw_featuresMichał Mirosław
just IP_CSUM. This needs testing and so is not changed here. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-07be2net: call FLR after setup wol in be_shutdownAjit Khaparde
Calling setup_wol after a reset is inconsequential. The WOL setting should be programmed before FLR. And yes, FLR does not erase wol information. Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-07be2net: dynamically allocate adapter->vf_cfgAjit Khaparde
Instead of a fixed sized array for vf_cfg, allocate the size dynamically depending on number of VFs the device supports. Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-07be2net: fix to get max VFs supported from adapterAjit Khaparde
The user supplied num_vfs value need not be compared against a static BE_MAX_VF, but can be checked against the actual VFs that the device can support. Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-07be2net: use common method to check for sriov function typeAjit Khaparde
Lancer and BE can both use SLI_INTF_REG to check a VF or a PF. Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-07be2net: add rxhash supportAjit Khaparde
Add rxhash support, Based on initial work by Eric Dumazet. Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-07Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/benet/be_main.c
2011-04-06ewrk3: convert to set_phys_idstephen hemminger
Use ethtool infrastructure for blinking, which is now does locking at higher level. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06qlcnic: convert to set_phys_idstephen hemminger
Convert driver to use new ethtool set_phys_id. Not completely sure that this is correct for all cases of device up/down and doing operation. Compile tested only. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06net: netxen: convert to hw_featuresMichał Mirosław
Rather simple conversion to hw_features. Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06capi: Perform scheduled capifs removalJan Kiszka
udev fully replaces this special file system that only contains CAPI NCCI TTY device nodes. User space (pppdcapiplugin) works without noticing the difference. Signed-off-by: Jan Kiszka <jan.kiszka@web.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06Signed bit field; int have_hotplug_status_watch:1Ian Campbell
Fixes error from sparse: CHECK drivers/net/xen-netback/xenbus.c drivers/net/xen-netback/xenbus.c:29:40: error: dubious one-bit signed bitfield int have_hotplug_status_watch:1; Reported-by: Dr. David Alan Gilbert <linux@treblig.org> Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06be2net: Fix suspend/resume operationPadmanabh Ratnakar
eq_next_idx is not getting reset to zero during suspend. This causes resume to fail. Added the fix. Signed-off-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@emulex.com> Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06be2net: Rename some struct members for clarityPadmanabh Ratnakar
Renamed msix_vec_idx to eq_idx in be_eq_obj struct. Renamed msix_vec_next_idx to eq_next_idx in be_adapter structure. These members are used in INTX mode also. Signed-off-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@emulex.com> Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06s2io: convert to set_phys_id (v2)stephen hemminger
Convert to new ethtool set physical id model. Remove no longer used timer, and fix docbook comment. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06niu: convert to new ethtool set_phys_idstephen hemminger
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06pcnet32: convert to set_phys_idstephen hemminger
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06benet: convert to set_phys_idstephen hemminger
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06bnx2x: convert to set_phys_idstephen hemminger
Also cleanup error codes to no lie about things that driver doesn't support. If device is down report -EAGAIN (same as Broadcom), and if port doesn't blink then error as well. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06bnx2: convert to set_phys_idstephen hemminger
In this case, need to add element to device private to hold original led state. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06vxge: convert to set_phys_idstephen hemminger
Also fix up incorrect docbook comment Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06cxgb3: implement set_phys_idstephen hemminger
Implement new ethtool set_phys_id on Chelsio cxgb3 board. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06tg3: implement ethtool set_phys_idstephen hemminger
Implement control of LED via set_phys_id. Note: since PHY is powered off if device is down, this board only allows blinking if device is up. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06skge: implement set_phys_idstephen hemminger
Implement set_phys_id led control on SysKonnect board. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06sky2: support ethtool set_phys_idstephen hemminger
Use ethtool set_phys_id to control LED. Fixes issues with RTNL being held for extended periods. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06pppoe: drop PPPOX_ZOMBIEs in pppoe_flush_devUlrich Weber
otherwise we loop forever if a PPPoE socket was set to PPPOX_ZOMBIE state by a PADT message when the ethernet device is going down afterwards. Signed-off-by: Ulrich Weber <uweber@astaro.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2011-04-06qlcnic: Update version number to 5.0.16Anirban Chakraborty
Bumped up version number to 5.0.16 Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-04-06qlcnic: Fix LRO disableRajesh Borundia
o In dev->open LRO was enabled by default, enable it depending upon netdev->features , kernel may have disabled it. o Configure LRO when interface is up. Signed-off-by: Rajesh Borundia <Rajesh.Borundia@qlogic.com> Signed-off-by: Anirban Chakraborty <Anirban.Chakraborty@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>