summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)Author
2013-08-07drm/radeon: only save UVD bo when we have open handlesChristian König
Otherwise just reinitialize from scratch on resume, and so make it more likely to succeed. Signed-off-by: Christian König <christian.koenig@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2013-08-07drm/radeon: always program the MC on startupAlex Deucher
For r6xx+ asics. This mirrors the behavior of pre-r6xx asics. We need to program the MC even if something else in startup() fails. Failure to do so results in an unusable GPU. Based on a fix from: Mark Kettenis <kettenis@openbsd.org> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
2013-08-07drm/radeon: fix audio dto calculation on DCE3+ (v3)Alex Deucher
Need to set the wallclock ratio and adjust the phase and module registers appropriately. May fix problems with audio timing at certain display timings. v2: properly handle clocks below 24mhz v3: rebase r600 changes Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2013-08-07drm/radeon/dpm: disable sclk ss on rv6xxAlex Deucher
Enabling spread spectrum on the engine clock leads to hangs on some asics. Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=66963 Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2013-08-07drm/radeon: fix halting UVDChristian König
Removing the clock/power or resetting the VCPU can cause hangs if that happens in the middle of a register write. Stall the memory and register bus before putting the VCPU into reset. Keep it in reset when unloading the module or suspending. Signed-off-by: Christian König <christian.koenig@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2013-08-07drm/radeon/dpm: adjust power state properly for UVD on SIAlex Deucher
There are some hardware issue with reclocking on SI when UVD is active, so use a stable power state when UVD is active. Fixes possible hangs and performance issues when using UVD on SI. Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2013-08-07drm/radeon/dpm: fix spread spectrum setup (v2)Alex Deucher
Need to check for engine and memory clock ss separately and only enable dynamic ss if either of them are found. This should fix systems which have a ss table, but do not have entries for engine or memory. On those systems we may enable dynamic spread spectrum without enabling it on the engine or memory clocks which can lead to a hang in some cases. fixes some systems reported here: https://bugs.freedesktop.org/show_bug.cgi?id=66963 v2: fix typo Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2013-08-07drm/radeon/dpm: adjust thermal protection requirementsAlex Deucher
On rv770 and newer, clock gating is not required for thermal protection. The only requirement is that the design utilizes a thermal sensor. Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2013-08-07drm/radeon: select audio dto based on encoder id for DCE3Alex Deucher
There are two audio dtos on radeon asics that you can select between. Normally, dto0 is used for hdmi and dto1 for DP, but it seems that the dto is somehow tied to the encoders on DCE3 asics. fixes: https://bugs.freedesktop.org/show_bug.cgi?id=67435 Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
2013-08-07drm/radeon: properly handle pm on gpu resetAlex Deucher
When we reset the GPU, we need to properly tear down power management before reseting the GPU and then set it back up again after reset. Add the missing radeon_pm_[suspend|resume] calls to the gpu reset function. Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2013-08-04drm/radeon: fix 64 bit divide in SI spm codeAlex Deucher
Forgot to use the appropriate math64 function. Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Dave Airlie <airlied@gmail.com>
2013-08-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds
Pull networking fixes from David Miller: 1) Don't ignore user initiated wireless regulatory settings on cards with custom regulatory domains, from Arik Nemtsov. 2) Fix length check of bluetooth information responses, from Jaganath Kanakkassery. 3) Fix misuse of PTR_ERR in btusb, from Adam Lee. 4) Handle rfkill properly while iwlwifi devices are offline, from Emmanuel Grumbach. 5) Fix r815x devices DMA'ing to stack buffers, from Hayes Wang. 6) Kernel info leak in ATM packet scheduler, from Dan Carpenter. 7) 8139cp doesn't check for DMA mapping errors, from Neil Horman. 8) Fix bridge multicast code to not snoop when no querier exists, otherwise mutlicast traffic is lost. From Linus Lüssing. 9) Avoid soft lockups in fib6_run_gc(), from Michal Kubecek. 10) Fix races in automatic address asignment on ipv6, which can result in incorrect lifetime assignments. From Jiri Benc. 11) Cure build bustage when CONFIG_NET_LL_RX_POLL is not set and rename it CONFIG_NET_RX_BUSY_POLL to eliminate the last reference to the original naming of this feature. From Cong Wang. 12) Fix crash in TIPC when server socket creation fails, from Ying Xue. 13) macvlan_changelink() silently succeeds when it shouldn't, from Michael S Tsirkin. 14) HTB packet scheduler can crash due to sign extension, fix from Stephen Hemminger. 15) With the cable unplugged, r8169 prints out a message every 10 seconds, make it netif_dbg() instead of netif_warn(). From Peter Wu. 16) Fix memory leak in rtm_to_ifaddr(), from Daniel Borkmann. 17) sis900 gets spurious TX queue timeouts due to mismanagement of link carrier state, from Denis Kirjanov. 18) Validate somaxconn sysctl to make sure it fits inside of a u16. From Roman Gushchin. 19) Fix MAC address filtering on qlcnic, from Shahed Shaikh. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (68 commits) qlcnic: Fix for flash update failure on 83xx adapter qlcnic: Fix link speed and duplex display for 83xx adapter qlcnic: Fix link speed display for 82xx adapter qlcnic: Fix external loopback test. qlcnic: Removed adapter series name from warning messages. qlcnic: Free up memory in error path. qlcnic: Fix ingress MAC learning qlcnic: Fix MAC address filter issue on 82xx adapter net: ethernet: davinci_emac: drop IRQF_DISABLED netlabel: use domain based selectors when address based selectors are not available net: check net.core.somaxconn sysctl values sis900: Fix the tx queue timeout issue net: rtm_to_ifaddr: free ifa if ifa_cacheinfo processing fails r8169: remove "PHY reset until link up" log spam net: ethernet: cpsw: drop IRQF_DISABLED htb: fix sign extension bug macvlan: handle set_promiscuity failures macvlan: better mode validation tipc: fix oops when creating server socket fails net: rename CONFIG_NET_LL_RX_POLL to CONFIG_NET_RX_BUSY_POLL ...
2013-08-03qlcnic: Fix for flash update failure on 83xx adapterHimanshu Madhani
Flash update routine was improperly checking register read API return value. Modify register read API and perform proper error check. Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-03qlcnic: Fix link speed and duplex display for 83xx adapterRajesh Borundia
o Set link speed and duplex to unknown when link is not up. Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-03qlcnic: Fix link speed display for 82xx adapterRajesh Borundia
o Do not obtain link speed from register when adapter link is down. Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-03qlcnic: Fix external loopback test.Shahed Shaikh
Driver was not handling external loopback diagnostic test request. Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-03qlcnic: Removed adapter series name from warning messages.Pratik Pujar
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-03qlcnic: Free up memory in error path.Himanshu Madhani
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-03qlcnic: Fix ingress MAC learningShahed Shaikh
o Delete MAC address from the adapter's filter table if the source MAC address of ingress packet matches. Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-03qlcnic: Fix MAC address filter issue on 82xx adapterShahed Shaikh
Driver was passing the address of a pointer instead of the pointer itself. Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-03net: ethernet: davinci_emac: drop IRQF_DISABLEDMugunthan V N
IRQF_DISABLED is a no-op by now and should be removed. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-03Merge tag 'hwmon-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging Pull hwmon fix from Guenter Roeck: "Fix chip initialization/configuration in MAX6697 driver" * tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: hwmon: (max6697) fix MAX6581 ideality
2013-08-03hwmon: (max6697) fix MAX6581 idealityVivien Didelot
Without this patch, the values for ideality (register 0x4b) and ideality selection mask (register 0x4c) are inverted. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Cc: stable@vger.kernel.org # 3.9+ Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2013-08-02sis900: Fix the tx queue timeout issueDenis Kirjanov
[ 198.720048] ------------[ cut here ]------------ [ 198.720108] WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:255 dev_watchdog+0x229/0x240() [ 198.720118] NETDEV WATCHDOG: eth0 (sis900): transmit queue 0 timed out [ 198.720125] Modules linked in: bridge stp llc dmfe sundance 3c59x sis900 mii [ 198.720159] CPU: 0 PID: 0 Comm: swapper Not tainted 3.11.0-rc3+ #12 [ 198.720167] Hardware name: System Manufacturer System Name/TUSI-M, BIOS ASUS TUSI-M ACPI BIOS Revision 1013 Beta 001 12/14/2001 [ 198.720175] 000000ff c13fa6b9 c169ddcc c12208d6 c169ddf8 c1031e4d c1664a84 c169de24 [ 198.720197] 00000000 c165f5ea 000000ff c13fa6b9 00000001 000000ff c1664a84 c169de10 [ 198.720217] c1031f13 00000009 c169de08 c1664a84 c169de24 c169de50 c13fa6b9 c165f5ea [ 198.720240] Call Trace: [ 198.720257] [<c13fa6b9>] ? dev_watchdog+0x229/0x240 [ 198.720274] [<c12208d6>] dump_stack+0x16/0x20 [ 198.720306] [<c1031e4d>] warn_slowpath_common+0x7d/0xa0 [ 198.720318] [<c13fa6b9>] ? dev_watchdog+0x229/0x240 [ 198.720330] [<c1031f13>] warn_slowpath_fmt+0x33/0x40 [ 198.720342] [<c13fa6b9>] dev_watchdog+0x229/0x240 [ 198.720357] [<c103f158>] call_timer_fn+0x78/0x150 [ 198.720369] [<c103f0e0>] ? internal_add_timer+0x40/0x40 [ 198.720381] [<c13fa490>] ? dev_init_scheduler+0xa0/0xa0 [ 198.720392] [<c103f33f>] run_timer_softirq+0x10f/0x200 [ 198.720412] [<c103954f>] ? __do_softirq+0x6f/0x210 [ 198.720424] [<c13fa490>] ? dev_init_scheduler+0xa0/0xa0 [ 198.720435] [<c1039598>] __do_softirq+0xb8/0x210 [ 198.720467] [<c14b54d2>] ? _raw_spin_unlock+0x22/0x30 [ 198.720484] [<c1003245>] ? handle_irq+0x25/0xd0 [ 198.720496] [<c1039c0c>] irq_exit+0x9c/0xb0 [ 198.720508] [<c14bc9d7>] do_IRQ+0x47/0x94 [ 198.720534] [<c1056078>] ? hrtimer_start+0x28/0x30 [ 198.720564] [<c14bc8b1>] common_interrupt+0x31/0x38 [ 198.720589] [<c1008692>] ? default_idle+0x22/0xa0 [ 198.720600] [<c10083c7>] arch_cpu_idle+0x17/0x30 [ 198.720631] [<c106d23d>] cpu_startup_entry+0xcd/0x180 [ 198.720643] [<c14ae30a>] rest_init+0xaa/0xb0 [ 198.720654] [<c14ae260>] ? reciprocal_value+0x50/0x50 [ 198.720668] [<c17044e0>] ? repair_env_string+0x60/0x60 [ 198.720679] [<c1704bda>] start_kernel+0x29a/0x350 [ 198.720690] [<c17044e0>] ? repair_env_string+0x60/0x60 [ 198.720721] [<c1704269>] i386_start_kernel+0x39/0xa0 [ 198.720729] ---[ end trace 81e0a6266f5c73a8 ]--- [ 198.720740] eth0: Transmit timeout, status 00000204 00000000 timer routine checks the link status and if it's up calls netif_carrier_on() allowing upper layer to start the tx queue even if the auto-negotiation process is not finished. Also remove ugly auto-negotiation check from the sis900_start_xmit() CC: Duan Fugang <B38611@freescale.com> CC: Ben Hutchings <bhutchings@solarflare.com> Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-02Merge tag 'rdma-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband Pull infiniband/rdma fixes from Roland Dreier: - Fixes for the newly merged mlx5 hardware driver - Stack info leak fixes from Dan Carpenter - Fixes for pkey table handling with SR-IOV - A few other small things * tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: IPoIB: Fix pkey change flow for virtualization environments IPoIB: Make sure child devices use valid/proper pkeys IB/core: Create QP1 using the pkey index which contains the default pkey mlx5_core: Variable may be used uninitialized mlx5_core: Implement new initialization sequence mlx5_core: Fix use after free in mlx5_cmd_comp_handler() IB/mlx5: Fix stack info leak in mlx5_ib_alloc_ucontext() IB/mlx5: Fix error return code in init_one() IB/mlx4: Use default pkey when creating tunnel QPs RDMA/cma: Only call cma_save_ib_info() for CM REQs RDMA/cma: Fix accessing invalid private data for UD RDMA/cma: Fix gcc warning Revert "RDMA/nes: Fix compilation error when nes_debug is enabled" IB/qib: Add err_decode() call for ring dump RDMA/cxgb3: Fix stack info leak in iwch_create_cq() RDMA/nes: Fix info leaks in nes_create_qp() and nes_create_cq() RDMA/ocrdma: Fix several stack info leaks RDMA/cxgb4: Fix stack info leak in c4iw_create_qp() RDMA/ocrdma: Remove unused include
2013-08-02Merge tag 'gpio-for-v3.11-3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO fixes from Linus Walleij: "Yet another GPIO pull request, fixing the fix from the last one. It turns out that fixing the boot path for device tree boots on OMAP breaks out antique systems (such as OMAP1) and we need to find a better way. So we're reverting that "fix" for the moment and thinking about something better. Also fixing a build issue on the MSM driver" * tag 'gpio-for-v3.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: gpio_msm: Fix build error due to missing err.h Revert "gpio/omap: don't create an IRQ mapping for every GPIO on DT" Revert "gpio/omap: auto request GPIO as input if used as IRQ via DT" Revert "gpio/omap: fix build error when OF_GPIO is not defined."
2013-08-02r8169: remove "PHY reset until link up" log spamLekensteyn
This message was added in commit a7154cb8 (June 2004, [PATCH] r8169: link handling and phy reset rework) and is printed every ten seconds when no cable is connected and runtime power management is disabled. (Before that commit, "Reset RTL8169s PHY" would be printed instead.) Signed-off-by: Peter Wu <lekensteyn@gmail.com> Acked-by: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-02net: ethernet: cpsw: drop IRQF_DISABLEDFelipe Balbi
IRQF_DISABLED is a no-op by now and should be removed. Signed-off-by: Felipe Balbi <balbi@ti.com> Acked-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-02Merge branch 'merge' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc Pull powerpc fixes from Ben Herrenschmidt: "Here is not quite a handful of powerpc fixes for rc3. The windfarm fix is a regression fix (though not a new one), the PMU interrupt rename is not a fix per-se but has been submitted a long time ago and I kept forgetting to put it in (it puts us back in sync with x86), the other perf bit is just about putting an API/ABI bit definition in the right place for userspace to consume, and finally, we have a fix for the VPHN (Virtual Partition Home Node) feature (notification that the hypervisor is moving nodes around) which could cause lockups so we may as well fix it now" * 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: powerpc/windfarm: Fix noisy slots-fan on Xserve (rm31) powerpc: VPHN topology change updates all siblings powerpc/perf: Export PERF_EVENT_CONFIG_EBB_SHIFT to userspace powerpc: Rename PMU interrupts from CNT to PMI
2013-08-02Merge branch 'parisc-3.11-rc4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux Pull parisc updates from Helge Deller: "The majority of lines changed are due the addition of a defconfig for the C8000 machine. Even the fix in parisc/kernel/cache.c file is actually ony a 10-line fix, but the change became bigger (and much nicer) to avoid errors of the checkpatch script. Here is the short-changelog: This round of parisc updates includes mostly fixes for the C8000 workstation. We have a new defconfig file for this machine, as well as fixes for it's serial port, the AGP driver and the cache routines to cope with the vmas of the FireGL card in a C8000. The sys32.h header file was not used and as such it's now gone" * 'parisc-3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: parisc: Fix interrupt routing for C8000 serial ports parisc: Remove arch/parisc/kernel/sys32.h header parisc: add defconfig for c8000 machine parisc: agp/parisc-agp: allow binding of user memory to the AGP GART parisc: Fix cache routines to ignore vma's with an invalid pfn
2013-08-02Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid Pull HID fixes from Jiri Kosina: - fix hid-sony PS3 sixaxxis breakage from Benjamin Tissories - fix hidraw race condition from Yonghua Zheng - fix/bandaid for rare device enumeration problems of Logitech Unifying receivers from Nestor Lopez Casado * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: HID: hidraw: fix improper mutex release HID: sony: fix HID mapping for PS3 sixaxis controller HID: hid-logitech-dj: querying_devices was never set HID: Revert "Revert "HID: Fix logitech-dj: missing Unifying device issue""
2013-08-02Merge tag 'pci-v3.11-fixes-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI fixes from Bjorn Helgaas: "Yinghai fixed a couple regressions: one resource assignment problem introduced in v3.10 that showed up with SR-IOV on powerpc, and another SR-IOV hot-remove issue related to refcounting changes we merged for v3.11. Yinghai is still working on another SR-IOV-related fix or two, which will be simpler if pciehp is non-modular, so I included the Kconfig changes now to get them in earlier. Finally, a minor fix for the ARM Marvell EBU host bridge driver that was merged for v3.11 Hotplug: PCI: pciehp: Fix null pointer deref when hot-removing SR-IOV device PCI: hotplug: Convert to be builtin only, not modular PCI: pciehp: Convert pciehp to be builtin only, not modular Resource allocation: PCI: Retry allocation of only the resource type that failed ARM: PCI: mvebu: Disable prefetchable memory support in PCI-to-PCI bridge" * tag 'pci-v3.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI: mvebu: Disable prefetchable memory support in PCI-to-PCI bridge PCI: Retry allocation of only the resource type that failed PCI: pciehp: Convert pciehp to be builtin only, not modular PCI: hotplug: Convert to be builtin only, not modular PCI: pciehp: Fix null pointer deref when hot-removing SR-IOV device
2013-08-02Merge tag 'pm+acpi-3.11-rc4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull ACPI and power management fixes from Rafael Wysocki: - Revert two cpuidle commits added during the 3.8 development cycle that turn out to have introduced a significant performance regression as requested by Jeremy Eder. - The recent patches that made the freezer less heavy-weight introduced a regression causing user-space-driven hibernation using the ioctl() interface to block indefinitely when the hibernate process executes try_to_freeze(). Fix from Colin Cross addresses this by adding a process flag to mark the hibernate/suspend process to inform the freezer that that process should be ignored. - One of the recent cpufreq reverts uncovered a problem in the core causing the cpufreq driver module refcount to become negative after a system suspend-resume cycle. Fix from Rafael J Wysocki. - The evaluation of the ACPI battery _BIX method has never worked correctly, because the commit that added support for it forgot to take the "Revision" field in the return package into account. As a result, the reading of battery info doesn't work at all on some systems, which is addressed by a fix from Lan Tianyu. * tag 'pm+acpi-3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: freezer: set PF_SUSPEND_TASK flag on tasks that call freeze_processes ACPI / battery: Fix parsing _BIX return value cpufreq: Fix cpufreq driver module refcount balance after suspend/resume Revert "cpuidle: Quickly notice prediction failure for repeat mode" Revert "cpuidle: Quickly notice prediction failure in general case"
2013-08-01macvlan: handle set_promiscuity failuresMichael S. Tsirkin
It's quite unlikely that dev_set_promiscuity will fail, but worth checking just in case. Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-01macvlan: better mode validationMichael S. Tsirkin
macvlan passthrough mode is special: it's not possible to switch to or from it through a netlink command. But if you try, the command will succeed, which is confusing. Validate input and return error to user. Cc: Sridhar Samudrala <sri@us.ibm.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-01net: rename CONFIG_NET_LL_RX_POLL to CONFIG_NET_RX_BUSY_POLLCong Wang
Eliezer renames several *ll_poll to *busy_poll, but forgets CONFIG_NET_LL_RX_POLL, so in case of confusion, rename it too. Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Cong Wang <amwang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-01net/mlx4_core: VFs must ignore the enable_64b_cqe_eqe module paramJack Morgenstein
Slaves get the 64B CQE/EQE state from QUERY_HCA, not from the module parameter. If the parameter is set to zero, the slave outputs an incorrect/irrelevant warning message that 64B CQEs/EQEs are supported but not enabled (even if the hypervisor has enabled 64B CQEs/EQEs). Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-01net/mlx4_core: Don't give VFs MAC addresses which are derived from the PF MACOr Gerlitz
If the user has not assigned a MAC address to a VM, then don't give it MAC which is based on the PF one. The current derivation scheme is wrong and leads to VM MAC collisions when the number of cards/hypervisors becomes big enough. Instead, just give it zeros and let them figure out what to do with that. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-01PCI: mvebu: Disable prefetchable memory support in PCI-to-PCI bridgeThomas Petazzoni
The Marvell PCIe driver uses an emulated PCI-to-PCI bridge to be able to dynamically set up MBus address decoding windows for PCI I/O and memory regions depending on the PCI devices enumerated by Linux. However, this emulated PCI-to-PCI bridge logic makes the Linux PCI core believe that prefetchable memory regions are supported (because the registers are read/write), while in fact no adress decoding window is ever created for such regions. Since the Marvell MBus address decoding windows do not distinguish memory regions and prefetchable memory regions, this patch takes a simple approach: change the PCI-to-PCI bridge emulation to let the Linux PCI core know that we don't support prefetchable memory regions. To achieve this, we simply make the prefetchable memory base a read-only register that always returns 0. Reading/writing all the other prefetchable memory related registers has no effect. This problem was originally reported by Finn Hoffmann <finn@uni-bremen.de>, who couldn't get a RTL8111/8168B PCI NIC working on the NSA310 Kirkwood platform after updating to 3.11-rc. The problem was that the PCI-to-PCI bridge emulation was making the Linux PCI core believe that we support prefetchable memory, so the Linux PCI core was only filling the prefetchable memory base and limit registers, which does not lead to a MBus window being created. The below patch has been confirmed by Finn Hoffmann to fix his problem on Kirkwood, and has otherwise been successfully tested on the Armada XP GP platform with a e1000e PCIe NIC and a Marvell SATA PCIe card. Reported-by: Finn Hoffmann <finn@uni-bremen.de> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2013-08-01Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
2013-08-01powerpc/windfarm: Fix noisy slots-fan on Xserve (rm31)Aaro Koskinen
slots-fan on G5 Xserve is always running at full speed with windfarm_rm31 driver, resulting in a very high acoustic noise level. It seems the fan parameters are incorrect, and have been copied from the Drive Bay fan (RPM, not present on rm31) of the legacy therm_pm72 driver. This patch changes the parameters to match the Slots fan (PWM) of therm_pm72. With the patch, slots-fan speed drops from 99% to 19% during normal use, and slots-temp settle to ~42'C. Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> CC: <stable@vger.kernel.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2013-07-31Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linuxLinus Torvalds
Pull drm fixes from Dave Airlie: "Radeon, nouveau, exynos, intel, mgag200.. Not all strictly regressions but there was probably only one patch I'd have really left out and it didn't seem worth respinning exynos to avoid it, the line change count is quite low. radeon: regressions + more dynamic powermanagement fixes, since DPM is a new feature, and off by default I'd prefer to keep merging fixes since it has a large userbase already and I'd like to keep them on mainline nouveau: is mostly regression fixes i915: is a regression fix since Daniel is on holidays I've merged it. mgag200: I've picked a bunch of targetted fixes from a big bunch of distro patches, exynos: build fixes mostly, one regression fix I expect things will slow right down now, I may send on the intel early quirk from Jesse separatly, since I think the x86 maintainers acked it" * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (37 commits) drm/i915: fix missed hunk after GT access breakage drm/radeon/dpm: re-enable cac control on SI drm/radeon/dpm: fix calculations in si_calculate_leakage_for_v_and_t_formula drm: fix 64 bit drm fixed point helpers drm/radeon/atom: initialize more atom interpretor elements to 0 drm/nouveau: fix semaphore dmabuf obj drm/nouveau/vm: make vm refcount into a kref drm/nv31/mpeg: don't recognize nv3x cards as having nv44 graph class drm/nv40/mpeg: write magic value to channel object to make it work drm/nouveau: fix size check for cards without vm drm/nv50-/disp: remove dcb_outp_match call, and related variables drm/nva3-/disp: fix hda eld writing, needs to be padded drm/nv31/mpeg: fix mpeg engine initialization drm/nv50/mc: include vp in the fb error reporting mask drm/nouveau: fix null pointer dereference in poll_changed drm/nv50/gpio: post-nv92 cards have 32 interrupt lines drm/nvc0/fb: take lock in nvc0_ram_put() drm/nouveau/core: xtensa firmware size needs to be 0x40000 no matter what drm/mgag200: Fix LUT programming for 16bpp drm/mgag200: Fix framebuffer pitch calculation ...
2013-07-31Merge tag 'fbdev-fixes-3.11-rc2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux Pull fbdev fixes from Tomi Valkeinen: "Small fbdev fixes: - compile fixes - atyfb initialization fix - Fix freeing of the irq in sh7760fb & nuc900fb" * tag 'fbdev-fixes-3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: video: sh7760fb: fix to pass correct device identity to free_irq() fbdev/atyfb: fix recent breakage in correct_chipset() fbdev/sgivwfb: fix compilation error in sgivwfb_mmap() video: nuc900fb: fix to pass correct device identity to request_irq() vga16fb: Remove unused variable video: xilinxfb: Fix compilation warning
2013-07-31Merge tag 'vfio-v3.11-rc4' of git://github.com/awilliam/linux-vfioLinus Torvalds
Pull vfio fixes from Alex Williamson: "misc fixes around overreacting to bus notifier events and a locking fix for a corner case blocked remove" * tag 'vfio-v3.11-rc4' of git://github.com/awilliam/linux-vfio: vfio-pci: Avoid deadlock on remove vfio: Ignore sprurious notifies vfio: Don't overreact to DEL_DEVICE
2013-07-31Merge branch 'akpm' (patches from Andrew Morton)Linus Torvalds
Merge more patches from Andrew Morton: "A bunch of fixes. Plus Joe's printk move and rework. It's not a -rc3 thing but now would be a nice time to offload it, while things are quiet. I've been sitting on it all for a couple of weeks, no issues" * emailed patches from Andrew Morton <akpm@linux-foundation.org>: vmpressure: make sure there are no events queued after memcg is offlined vmpressure: do not check for pending work to prevent from new work vmpressure: change vmpressure::sr_lock to spinlock printk: rename struct log to struct printk_log printk: use pointer for console_cmdline indexing printk: move braille console support into separate braille.[ch] files printk: add console_cmdline.h printk: move to separate directory for easier modification drivers/rtc/rtc-twl.c: fix: rtcX/wakealarm attribute isn't created mm: zbud: fix condition check on allocation size thp, mm: avoid PageUnevictable on active/inactive lru lists mm/swap.c: clear PageActive before adding pages onto unevictable list arch/x86/platform/ce4100/ce4100.c: include reboot.h mm: sched: numa: fix NUMA balancing when !SCHED_DEBUG rapidio: fix use after free in rio_unregister_scan() .gitignore: ignore *.lz4 files MAINTAINERS: dynamic debug: Jason's not there... dmi_scan: add comments on dmi_present() and the loop in dmi_scan_machine() ocfs2/refcounttree: add the missing NULL check of the return value of find_or_create_page() mm: mempolicy: fix mbind_range() && vma_adjust() interaction
2013-07-318139cp: Add dma_mapping_error checkingNeil Horman
Self explanitory dma_mapping_error addition to the 8139 driver, based on this: https://bugzilla.redhat.com/show_bug.cgi?id=947250 It showed several backtraces arising for dma_map_* usage without checking the return code on the mapping. Add the check and abort the rx/tx operation if its failed. Untested as I have no hardware and the reporter has wandered off, but seems pretty straightforward. Signed-off-by: Neil Horman <nhorman@tuxdriver.com> CC: "David S. Miller" <davem@davemloft.net> CC: Francois Romieu <romieu@fr.zoreil.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-01Merge branches 'for-3.11/upstream-fixes' and ↵Jiri Kosina
'for-3.11/logitech-enumeration-fix' into for-linus
2013-07-31net/usb/r8152: adjust relative ocp functionhayeswang
- fix the conversion between cpu and __le32 - replace some pla_ocp and usb_ocp functions with generic_ocp function Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-07-31net/usb/r8152: make sure the USB buffer is DMA-ablehayeswang
Allocate the required memory before calling usb_control_msg. And the additional memory copy is necessary. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-07-31net/usb/r815x: change the return value for bind functionshayeswang
Replace 0 with the result from usbnet_cdc_bind(). Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net>