| Age | Commit message (Collapse) | Author |
|---|
|
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the remaining fixes for v3.15.
This series includes:
- iser-target fix for ImmediateData exception reference count bug
(Sagi + nab)
- iscsi-target fix for MC/S login + potential iser-target MRDSL
buffer overrun (Santosh + Roland)
- iser-target fix for v3.15-rc multi network portal shutdown
regression (nab)
- target fix for allowing READ_CAPCITY during ALUA Standby access
state (Chris + nab)
- target fix for NULL pointer dereference of alua_access_state for
un-configured devices (Chris + nab)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix alua_access_state attribute OOPs for un-configured devices
target: Allow READ_CAPACITY opcode in ALUA Standby access state
iser-target: Fix multi network portal shutdown regression
iscsi-target: Fix wrong buffer / buffer overrun in iscsi_change_param_value()
iser-target: Add missing target_put_sess_cmd for ImmedateData failure
|
|
Cpufreq governors like the ondemand governor calculate the load on the CPU
periodically by employing deferrable timers. A deferrable timer won't fire
if the CPU is completely idle (and there are no other timers to be run), in
order to avoid unnecessary wakeups and thus save CPU power.
However, the load calculation logic is agnostic to all this, and this can
lead to the problem described below.
Time (ms) CPU 1
100 Task-A running
110 Governor's timer fires, finds load as 100% in the last
10ms interval and increases the CPU frequency.
110.5 Task-A running
120 Governor's timer fires, finds load as 100% in the last
10ms interval and increases the CPU frequency.
125 Task-A went to sleep. With nothing else to do, CPU 1
went completely idle.
200 Task-A woke up and started running again.
200.5 Governor's deferred timer (which was originally programmed
to fire at time 130) fires now. It calculates load for the
time period 120 to 200.5, and finds the load is almost zero.
Hence it decreases the CPU frequency to the minimum.
210 Governor's timer fires, finds load as 100% in the last
10ms interval and increases the CPU frequency.
So, after the workload woke up and started running, the frequency was suddenly
dropped to absolute minimum, and after that, there was an unnecessary delay of
10ms (sampling period) to increase the CPU frequency back to a reasonable value.
And this pattern repeats for every wake-up-from-cpu-idle for that workload.
This can be quite undesirable for latency- or response-time sensitive bursty
workloads. So we need to fix the governor's logic to detect such wake-up-from-
cpu-idle scenarios and start the workload at a reasonably high CPU frequency.
One extreme solution would be to fake a load of 100% in such scenarios. But
that might lead to undesirable side-effects such as frequency spikes (which
might also need voltage changes) especially if the previous frequency happened
to be very low.
We just want to avoid the stupidity of dropping down the frequency to a minimum
and then enduring a needless (and long) delay before ramping it up back again.
So, let us simply carry forward the previous load - that is, let us just pretend
that the 'load' for the current time-window is the same as the load for the
previous window. That way, the frequency and voltage will continue to be set
to whatever values they were set at previously. This means that bursty workloads
will get a chance to influence the CPU frequency at which they wake up from
cpu-idle, based on their past execution history. Thus, they might be able to
avoid suffering from slow wakeups and long response-times.
However, we should take care not to over-do this. For example, such a "copy
previous load" logic will benefit cases like this: (where # represents busy
and . represents idle)
##########.........#########.........###########...........##########........
but it will be detrimental in cases like the one shown below, because it will
retain the high frequency (copied from the previous interval) even in a mostly
idle system:
##########.........#.................#.....................#...............
(i.e., the workload finished and the remaining tasks are such that their busy
periods are smaller than the sampling interval, which causes the timer to
always get deferred. So, this will make the copy-previous-load logic copy
the initial high load to subsequent idle periods over and over again, thus
keeping the frequency high unnecessarily).
So, we modify this copy-previous-load logic such that it is used only once
upon every wakeup-from-idle. Thus if we have 2 consecutive idle periods, the
previous load won't get blindly copied over; cpufreq will freshly evaluate the
load in the second idle interval, thus ensuring that the system comes back to
its normal state.
[ The right way to solve this whole problem is to teach the CPU frequency
governors to also track load on a per-task basis, not just a per-CPU basis,
and then use both the data sources intelligently to set the appropriate
frequency on the CPUs. But that involves redesigning the cpufreq subsystem,
so this patch should make the situation bearable until then. ]
Experimental results:
+-------------------+
I ran a modified version of ebizzy (called 'sleeping-ebizzy') that sleeps in
between its execution such that its total utilization can be a user-defined
value, say 10% or 20% (higher the utilization specified, lesser the amount of
sleeps injected). This ebizzy was run with a single-thread, tied to CPU 8.
Behavior observed with tracing (sample taken from 40% utilization runs):
------------------------------------------------------------------------
Without patch:
~~~~~~~~~~~~~~
kworker/8:2-12137 416.335742: cpu_frequency: state=2061000 cpu_id=8
kworker/8:2-12137 416.335744: sched_switch: prev_comm=kworker/8:2 ==> next_comm=ebizzy
<...>-40753 416.345741: sched_switch: prev_comm=ebizzy ==> next_comm=kworker/8:2
kworker/8:2-12137 416.345744: cpu_frequency: state=4123000 cpu_id=8
kworker/8:2-12137 416.345746: sched_switch: prev_comm=kworker/8:2 ==> next_comm=ebizzy
<...>-40753 416.355738: sched_switch: prev_comm=ebizzy ==> next_comm=kworker/8:2
<snip> --------------------------------------------------------------------- <snip>
<...>-40753 416.402202: sched_switch: prev_comm=ebizzy ==> next_comm=swapper/8
<idle>-0 416.502130: sched_switch: prev_comm=swapper/8 ==> next_comm=ebizzy
<...>-40753 416.505738: sched_switch: prev_comm=ebizzy ==> next_comm=kworker/8:2
kworker/8:2-12137 416.505739: cpu_frequency: state=2061000 cpu_id=8
kworker/8:2-12137 416.505741: sched_switch: prev_comm=kworker/8:2 ==> next_comm=ebizzy
<...>-40753 416.515739: sched_switch: prev_comm=ebizzy ==> next_comm=kworker/8:2
kworker/8:2-12137 416.515742: cpu_frequency: state=4123000 cpu_id=8
kworker/8:2-12137 416.515744: sched_switch: prev_comm=kworker/8:2 ==> next_comm=ebizzy
Observation: Ebizzy went idle at 416.402202, and started running again at
416.502130. But cpufreq noticed the long idle period, and dropped the frequency
at 416.505739, only to increase it back again at 416.515742, realizing that the
workload is in-fact CPU bound. Thus ebizzy needlessly ran at the lowest frequency
for almost 13 milliseconds (almost 1 full sample period), and this pattern
repeats on every sleep-wakeup. This could hurt latency-sensitive workloads quite
a lot.
With patch:
~~~~~~~~~~~
kworker/8:2-29802 464.832535: cpu_frequency: state=2061000 cpu_id=8
<snip> --------------------------------------------------------------------- <snip>
kworker/8:2-29802 464.962538: sched_switch: prev_comm=kworker/8:2 ==> next_comm=ebizzy
<...>-40738 464.972533: sched_switch: prev_comm=ebizzy ==> next_comm=kworker/8:2
kworker/8:2-29802 464.972536: cpu_frequency: state=4123000 cpu_id=8
kworker/8:2-29802 464.972538: sched_switch: prev_comm=kworker/8:2 ==> next_comm=ebizzy
<...>-40738 464.982531: sched_switch: prev_comm=ebizzy ==> next_comm=kworker/8:2
<snip> --------------------------------------------------------------------- <snip>
kworker/8:2-29802 465.022533: sched_switch: prev_comm=kworker/8:2 ==> next_comm=ebizzy
<...>-40738 465.032531: sched_switch: prev_comm=ebizzy ==> next_comm=kworker/8:2
kworker/8:2-29802 465.032532: sched_switch: prev_comm=kworker/8:2 ==> next_comm=ebizzy
<...>-40738 465.035797: sched_switch: prev_comm=ebizzy ==> next_comm=swapper/8
<idle>-0 465.240178: sched_switch: prev_comm=swapper/8 ==> next_comm=ebizzy
<...>-40738 465.242533: sched_switch: prev_comm=ebizzy ==> next_comm=kworker/8:2
kworker/8:2-29802 465.242535: sched_switch: prev_comm=kworker/8:2 ==> next_comm=ebizzy
<...>-40738 465.252531: sched_switch: prev_comm=ebizzy ==> next_comm=kworker/8:2
Observation: Ebizzy went idle at 465.035797, and started running again at
465.240178. Since ebizzy was the only real workload running on this CPU,
cpufreq retained the frequency at 4.1Ghz throughout the run of ebizzy, no
matter how many times ebizzy slept and woke-up in-between. Thus, ebizzy
got the 10ms worth of 4.1 Ghz benefit during every sleep-wakeup (as compared
to the run without the patch) and this boost gave a modest improvement in total
throughput, as shown below.
Sleeping-ebizzy records-per-second:
-----------------------------------
Utilization Without patch With patch Difference (Absolute and % values)
10% 274767 277046 + 2279 (+0.829%)
20% 543429 553484 + 10055 (+1.850%)
40% 1090744 1107959 + 17215 (+1.578%)
60% 1634908 1662018 + 27110 (+1.658%)
A rudimentary and somewhat approximately latency-sensitive workload such as
sleeping-ebizzy itself showed a consistent, noticeable performance improvement
with this patch. Hence, workloads that are truly latency-sensitive will benefit
quite a bit from this change. Moreover, this is an overall win-win since this
patch does not hurt power-savings at all (because, this patch does not reduce
the idle time or idle residency; and the high frequency of the CPU when it goes
to cpu-idle does not affect/hurt the power-savings of deep idle states).
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
i2c_smbus_read_word_data() does host endian conversion already,
no need for le16_to_cpu()
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
|
|
An obviously missing 'select' statement, without this we
get a link error
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Lars writes: "I'm only 99% sure that the net interfaces are qmi
interfaces, nothing to lose by adding them in my opinion."
And I tend to agree based on the similarity with the two Olicard
modems we already have here.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge more updates from Andrew Morton:
- Most of the rest of MM.
This includes "mark remap_file_pages syscall as deprecated" but the
actual "replace remap_file_pages syscall with emulation" is held
back. I guess we'll need to work out when to pull the trigger on
that one.
- various minor cleanups to obscure filesystems
- the drivers/rtc queue
- hfsplus updates
- ufs, hpfs, fatfs, affs, reiserfs
- Documentation/
- signals
- procfs
- cpu hotplug
- lib/idr.c
- rapidio
- sysctl
- ipc updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (171 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
|
|
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Len field is already set to zero, but not the from field which is sent
as 0xfffffffffffffe00. This makes no sense, and may cause confuse
server implementations doing sanity checks (qemu-nbd is an example.)
Signed-off-by: Hani Benhabiles <hani@linux.com>
Cc: Paul Clements <paul.clements@us.sios.com>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some sysrq handlers can run for a long time, because they dump a lot of
data onto a serial console. Having RCU stall warnings pop up in the
middle of them only makes the problem worse.
This patch temporarily disables RCU stall warnings while a sysrq request
is handled.
Signed-off-by: Rik van Riel <riel@redhat.com>
Suggested-by: Paul McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Madper Xie <cxie@redhat.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Echoing values into /proc/sysrq-trigger seems to be a popular way to get
information out of the kernel. However, dumping information about
thousands of processes, or hundreds of CPUs to serial console can result
in IRQs being blocked for minutes, resulting in various kinds of cascade
failures.
The most common failure is due to interrupts being blocked for a very
long time. This can lead to things like failed IO requests, and other
things the system cannot easily recover from.
This problem is easily fixable by making __handle_sysrq use RCU instead
of spin_lock_irqsave.
This leaves the warning that RCU grace periods have not elapsed for a
long time, but the system will come back from that automatically.
It also leaves sysrq-from-irq-context when the sysrq keys are pressed,
but that is probably desired since people want that to work in
situations where the system is already hosed.
The callers of register_sysrq_key and unregister_sysrq_key appear to be
capable of sleeping.
Signed-off-by: Rik van Riel <riel@redhat.com>
Reported-by: Madper Xie <cxie@redhat.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers using these two
interfaces need to be updated to use the new pci_enable_msi_range() or
pci_enable_msi_exact() and pci_enable_msix_range() or
pci_enable_msix_exact() interfaces.
The patch has no runtime effect.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Acked-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When RTC CLKTRCTRL bit is configured in HW_AUTO, module goes to sleep in
IDLE state.
The Alarm SWakeup event can be used to wakeup the RTC when it is in IDLE
state. In order to do so, the alarm needs to be set and enabled before
RTC enters the IDLE state. Also the wakeup generation for alarm/timer
event needs to be set (bits [1:0] in RTC_IRQWAKEEN register).
Currently RTC_IRQWAKEEN bits are set only in suspend/resume paths. With
this ALARM interrupts are not generated when it enters IDLE state. So
programming the RTC_IRQWAKEEN bits when ever ALARM is set.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The rtc user must wait at least 1 sec between each time/calandar update
(see atmel's datasheet chapter "Updating Time/Calendar").
Use the 1Hz interrupt to update the at91_rtc_upd_rdy flag and wait for
the at91_rtc_wait_upd_rdy event if the rtc is not ready.
This patch fixes a deadlock in an uninterruptible wait when the RTC is
updated more than once every second. AFAICT the bug is here from the
beginning, but I think we should at least backport this fix to 3.10 and
the following longterm and stable releases.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Bryan Evenson <bevenson@melinkcorp.com>
Tested-by: Bryan Evenson <bevenson@melinkcorp.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This enables the setting of a custom clock name for the clock provided by
the hym8563 rtc.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The RTC framework does not let you return an error once a call to
devm_rtc_device_register has succeeded. Avoid doing that when the IRQ
request fails as we can still support reading/writing the clock without
the IRQ.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reported-by: Ales Novak <alnovak@suse.cz>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Newer versions of OMAP RTC IP such as those found in AM335x and DRA7x
need an explicit enable of 32khz functional clock which ticks the RTC.
AM335x support was working so far because of settings done in U-Boot.
However, the DRA7x U-Boot does no such enable of 32khz clock and this
patch is need to get the RTC to work on DRA7x at least. In general, it
is better to not depend on settings done in U-Boot.
Thanks to Lokesh Vutla for noticing this.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use BIT() macro for RTC_HAS_<FEATURE> defines instead of hand-writing
bit masks.
Use BIT() macros for register bit field definitions.
While at it, fix indentation done using spaces.
No functional change in this patch.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove multiple superfluous device id checks. Since an id_table is
present in the driver probe() should never encounter an empty device id
entry. In case of OF style match, of_match_device() returns an matching
entry.
For paranoia sake, check for device id entry once and fail probe() if none
is found. This is much better than checking for it multiple times.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add the RTC driver for DA9063.
[akpm@linux-foundation.org: coding-style tweaks]
Signed-off-by: Opensource [Steve Twiss] <stwiss.opensource@diasemi.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Mark Brown <broonie@linaro.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add driver for SPI RTC Microchip MCP795. Only supports saving/loading
time from the chip (i. e. no alarms/power events/ID).
Signed-off-by: Josef Gajdusek <atx@atx.name>
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Avoid the potential race condition by avoiding bailing out of driver in
probe after registering with rtc subsystem
Also the set_alarm , read_alarm and alarm_irq_enable returns error if irq
registration fails in probe.
Also the sysfs will not create entry for alarm if irq registration fails
in probe.
Signed-off-by: Raghavendra Chandra Ganiga <ravi23ganiga@gmail.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the following build errors reported by kbuild test robot by selecting
REGMAP_SPI in Kconfig file
drivers/built-in.o: In function `ds1343_probe':
rtc-ds1343.c:(.text+0x1baf8f): undefined reference to `devm_regmap_init_spi'
Signed-off-by: Raghavendra Chandra Ganiga <ravi23ganiga@gmail.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Raghavendra Chandra Ganiga <ravi23ganiga@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make of_device_id array const, because all OF functions handle it as
const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make of_device_id array const, because all OF functions handle it as
const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make of_device_id array const, because all OF functions handle it as
const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make of_device_id array const, because all OF functions handle it as
const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Heiko Stbner <heiko@sntech.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make of_device_id array const, because all OF functions handle it as
const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Setting the alarm to a time not on a minute boundary results in repeated
interrupts being generated by the DA9052/3 PMIC device until the kernel
RTC core sees that the alarm has rung. Sometimes the number and frequency
of interrupts can cause the kernel to disable the IRQ line used by the
DA9052/3 PMIC with disasterous consequences. This patch fixes the
problem.
Even though the DA9052/3 PMIC is capable generating periodic interrupts,
ie TICKS, the method used to distinguish RTC_AF from RTC_PF events was
flawed and can not work in conjunction with the regmap_irq kernel core.
Thus that flawed detection has also been removed by the DA9052/3 PMIC RTC
driver's irq handler, so that it no longer reports the wrong type of event
to the kernel RTC core.
The internal static functions within the DA9052/3 PMIC RTC driver have
been changed to pass the 'da9052_rtc' structure instead of the 'da9052'
because there is no backwards pointer from the 'da9052' structure.
This patch fixes the three issues described above. The first is serious
because usiing the RTC alarm set to a non minute boundary will eventually
cause all component drivers that depend on the interrupt line to fail.
The solution adopted is to round up to alarm time to the next highest
minute.
The second bug, reporting a RTC_PF event instead of an RTC_AF event turns
out to not matter with the current implementation of the kernel RTC core
as it seems to ignore the event type. However, should that change in the
future it is better to fix the issue now and not have 'problems waiting to
happen'
The third set of changes are to make the da9052_rtc structure available to
all the local internal functions in the driver. This was done during
testing so that diagnostic data could be stored there. Should the
solution to the first issue be found not acceptable, then the alternative
of using the TICKS interrupt at the fixed one second interval in order to
step to the exact second of the requested alarm requires an extra (alarm
time) piece of data to be stored. In devices that use the alarm function
to wake up from sleep, accuracy to the second will result in the device
being awake for up to nearly a minute longer than expected.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Cc: David Dajun Chen <dchen@diasemi.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add missing of_node_put() to decrement the reference count.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use of_get_child_by_name() to obtain reference to charger node instead of
of_find_node_by_name() which can walk outside of the parent node.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This brings in drivers/char/rtc.c functionality required for DECstation
and, should the maintainers decide to switch, Alpha systems to use
rtc-cmos.
Specifically these features are made available:
* RTC iomem rather than x86/PCI port I/O mapping, controlled with the
RTC_IOMAPPED macro as with the original driver. The DS1287A chip in all
DECstation systems is mapped in the host bus address space as a
contiguous block of 64 32-bit words of which the least significant byte
accesses the RTC chip for both reads and writes. All the address and
data window register accesses are made transparently by the chipset glue
logic so that the device appears directly mapped on the host bus.
* A way to set the size of the address space explicitly with the
newly-added `address_space' member of the platform part of the RTC
device structure. This avoids the unreliable heuristics that does not
work in a setup where the RTC is not explicitly accessed with the usual
address and data window register pair.
* The ability to use the RTC periodic interrupt as a system clock
device, which is implemented by arch/mips/kernel/cevt-ds1287.c for
DECstation systems and takes the RTC interrupt away from the RTC driver.
Eventually hooking back to the clock device's interrupt handler should
be possible for the purpose of the alarm clock and possibly also
update-in-progress interrupt, but this is not done by this change.
o To avoid interfering with the clock interrupt all the places where
the RTC interrupt mask is fiddled with are only executed if and IRQ
has been assigned to the RTC driver.
o To avoid changing the clock setup Register A is not fiddled with
if CMOS_RTC_FLAGS_NOFREQ is set in the newly-added `flags' member of
the platform part of the RTC device structure. Originally, in
drivers/char/rtc.c, this was keyed with the absence of the RTC
interrupt, just like the interrupt mask, but there only the periodic
interrupt frequency is set, whereas rtc-cmos also sets the divider
bits. Therefore a new flag is introduced so that systems where the
RTC interrupt is not usable rather than used as a system clock device
can fully initialise the RTC.
* A small clean-up is made to the IRQ assignment code that makes the IRQ
number hardcoded to -1 rather than arbitrary -ENXIO (or whatever error
happens to be returned by platform_get_irq) where no IRQ has been
assigned to the RTC driver (NO_IRQ might be another candidate, but it
looks like this macro has inconsistent or missing definitions and
limited use and might therefore be unsafe).
Verified to work correctly with a DECstation 5000/240 system.
[akpm@linux-foundation.org: fix weird code layout]
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Compared source code of rtc-lib.c::rtc_year_days() with
efirtc.c::rtc_year_days(), found the code in rtc-efi decreases value of
day twice when it computing year days. rtc-lib.c::rtc_year_days() has
already decrease days and return the year days from 0 to 365.
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Don't replace the value we got from the I2C layer, just pass it on.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There is no cleanup needed when something fails in probe, so no need for
goto. Directly return when something fails.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
History is in git, no need for sperate versioning. Also remove the
success printout, RTC core does it, too.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add support for the APM X-Gene SoC RTC driver.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Loc Ho <lho@apm.com>
Cc: Jon Masters <jcm@redhat.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In __rtc_read_alarm(), if the alarm time retrieved by
rtc_read_alarm_internal() from the device contains invalid values (e.g.
month=2,mday=31) and the year not set (=-1), the initialization will
loop infinitely because the year-fixing loop expects the time being
invalid due to leap year.
Fix reduces the loop to the leap years and adds final validity check.
Signed-off-by: Ales Novak <alnovak@suse.cz>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Reported-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Adds trace events that give finer resolution into suspend/resume. These
events are graphed in the timelines generated by the analyze_suspend.py
script. They represent large areas of time consumed that are typical to
suspend and resume.
The event is triggered by calling the function "trace_suspend_resume"
with three arguments: a string (the name of the event to be displayed
in the timeline), an integer (case specific number, such as the power
state or cpu number), and a boolean (where true is used to denote the start
of the timeline event, and false to denote the end).
The suspend_resume trace event reproduces the data that the machine_suspend
trace event did, so the latter has been removed.
Signed-off-by: Todd Brandt <todd.e.brandt@intel.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
Convert "x == true" to "x" and "x == false" to "!x".
Signed-off-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
