summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)Author
2011-10-03mac80211: pass vif param to conf_tx() callbackEliad Peller
tx params should be configured per interface. add ieee80211_vif param to the conf_tx callback, and change all the drivers that use this callback. The following spatch was used: @rule1@ struct ieee80211_ops ops; identifier conf_tx_op; @@ ops.conf_tx = conf_tx_op; @rule2@ identifier rule1.conf_tx_op; identifier hw, queue, params; @@ conf_tx_op ( - struct ieee80211_hw *hw, + struct ieee80211_hw *hw, struct ieee80211_vif *vif, u16 queue, const struct ieee80211_tx_queue_params *params) {...} Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-03iwlagn: rename iwlagn module iwlwifi and alias to iwlagn.Don Fry
Rename the iwlagn module as iwlwifi in preparation for future changes. Add an alias to iwlagn for backward compatibility. Signed-off-by: Don Fry <donald.h.fry@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-03ath9k_hw: extend GPIO pin select mask for rfkillMohammed Shafi Shajakhan
this extends the bits for rf kill GPIO selection to [7:2] from [4:2] as we use GPIO pin 11 as rfkill for AR9480 and also remove few unused macros Cc: Wilson Tsao <wtsao@qca.qualcomm.com> Cc: "Hu, Russell" <rhu@qca.qualcomm.com> Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-03mwifiex: handle an error path correctlyAmitkumar Karwar
In failure case locks are not allocated in mwifiex_register(). So mwifiex_free_lock_list() routine call becomes redundant. Also we don't need to check return type for mwifiex_init_lock_list() routine. It never fails. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-03mwifiex: correct AMSDU aggregation checkAmitkumar Karwar
The commit "mwifiex: remove list traversal.."(fcf2176c87..) wrongly modifies AMSDU aggregation check. Due to this even though packet size for iperf traffic is already large, we unnecessarily try to aggregate them which adds some delay. If Tx iperf is started on UUT for 30 seconds, UUT keeps sending Tx packets for few more seconds. That commit is reverted to fix the problem. Also, MIN_NUM_AMSDU check is moved inside the loop to optimize the loop. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-03ath9k_htc: add AVM FRITZ!WLAN 11N v2 supportLuis R. Rodriguez
This was reported and tested by Martin Walter over at AVM GmbH Berlin. This also applies to 3.0.1 so sendint to stable. Cc: s.kirste@avm.de Cc: d.friedel@avm.de Cc: Martin Walter <m.walter@avm.de> Cc: Peter Grabienski <pgrabien@qca.qualcomm.com> Cc: stable@kernel.org Tested-by: Martin Walter <m.walter@avm.de> Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-10-03Merge branch 'for-linville' of git://github.com/kvalo/ath6klJohn W. Linville
2011-10-03ath6kl: include vmalloc.h in debug.cKalle Valo
Fixes compilation errors when compiling for ARM: ath6kl/debug.c:312: error: implicit declaration of function 'vmalloc' ath6kl/debug.c:312: warning: assignment makes pointer from integer without a cast ath6kl/debug.c:342: error: implicit declaration of function 'vfree' ath6kl/debug.c:696: warning: assignment makes pointer from integer without a cast ath6kl/debug.c:871: warning: assignment makes pointer from integer without a cast Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2011-10-01ath6kl: fix size_t related warningsKalle Valo
My earlier debug log additions added these warnings when compiling 64 bit kernels: ath6kl/init.c:962: warning: format '%d' expects type 'int', but argument 3 has type 'size_t' ath6kl/init.c:975: warning: format '%d' expects type 'int', but argument 3 has type 'size_t' ath6kl/init.c:988: warning: format '%d' expects type 'int', but argument 3 has type 'size_t' ath6kl/init.c:1009: warning: format '%d' expects type 'int', but argument 3 has type 'size_t' ath6kl/init.c:1192: warning: format '%d' expects type 'int', but argument 4 has type 'size_t' ath6kl/init.c:1236: warning: format '%d' expects type 'int', but argument 4 has type 'size_t' ath6kl/init.c:1267: warning: format '%d' expects type 'int', but argument 4 has type 'size_t' Reported-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2011-09-30mac80211: implement uAPSDJohannes Berg
Add uAPSD support to mac80211. This is probably not possible with all devices, so advertising it with the cfg80211 flag will be left up to drivers that want it. Due to my previous patches it is now a fairly straight-forward extension. Drivers need to have accurate TX status reporting for the EOSP frame. For drivers that buffer themselves, the provided APIs allow releasing the right number of frames, but then drivers need to set EOSP and more-data themselves. This is documented in more detail in the new code itself. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-30mac80211: let drivers inform it about per TID buffered framesJohannes Berg
For uAPSD implementation, it is necessary to know on which ACs frames are buffered. mac80211 obviously knows about the frames it has buffered itself, but with aggregation many drivers buffer frames. Thus, mac80211 needs to be informed about this. For now, since we don't have APSD in any form, this will unconditionally set the TIM bit for the station but later with uAPSD only some ACs might cause the TIM bit to be set. ath9k is the only driver using this API and I only modify it in the most basic way, it won't be able to implement uAPSD with this yet. But it can't do that anyway since there's no way to selectively release frames to the peer yet. Since drivers will buffer frames per TID, let them inform mac80211 on a per TID basis, mac80211 will then sort out the AC mapping itself. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-30iwlagn: iwl-agn-rs: remove unnecessary null check for sta and lq_staGreg Dietsche
both sta and lq_sta are guaranteed to be not null in the calling function so we don't need to check them here. Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-30ath9k/ath9k_htc: Fix PS wrappers for RF killMohammed Shafi Shajakhan
ath9k_hw_gpio_get reads the GPIO in/out registers to get the status of GPIO pins, so use PS wrappers Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-30rtlwifi: Remove unused _usb_nbytes_read_write and _usb_writeN_syncLarry Finger
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-30rtlwifi: Remove unused routine _usb_readN_syncLarry Finger
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-30mwifiex: add cfg80211 handlers add/del_virtual_intfYogesh Ashok Powar
Making adding and deleting virtual interfaces dynamic. Adding handlers for creating and deleting virtual interface with given name and dev respectively. Also, creating default interface of type station on insmod of the driver. Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-30mwifiex: fix Tx data rate display issueAmitkumar Karwar
"iw dev mlan0 link" shows wrong data rate, because data rate is not sent properly to cfg80211 stack. Also stack is not updated with mcs and Tx data flags information. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-30mwifiex: remove unreachable codeAmitkumar Karwar
In disconnected state "iw dev mlan0 link" command will return from cfg80211 stack itself. We also have an error check in mwifiex_cfg80211_get_station() routine. Therefore the code under "if (!priv->media_connected)" condition in mwifiex_rate_ioctl_get_rate_value() routine becomes unreachable. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-30mwifiex: remove unnecessary mwifiex_dump_station_info() callAmitkumar Karwar
An extra call to mwifiex_dump_station_info() routine in get_station callback function is redundant Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-30ath9k: Remove redundant my beacon check at ath_rx_ps_beaconRajkumar Manoharan
Make use of the rx status's is_mybeacon in order to avoid redundant memcmp. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-30ath9k: Remove unnecessary AMPDU check at tx statusRajkumar Manoharan
Fill the ampdu_[ack]_len for both aggregation and normal frames. So that we could avoid unnecesary conditional at tx status. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-30wireless: at76c50x: use native hex_pack_byte() methodAndy Shevchenko
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: "John W. Linville" <linville@tuxdriver.com> Tested-by: Pavel Roskin <proski@gnu.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-28wireless/ath6kl: use of module_param requires the inclusion of moduleparam.hStephen Rothwell
Otheriwse the module.h split up fails like this: drivers/net/wireless/ath/ath6kl/init.c:27:26: error: expected ')' before 'uint' Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2011-09-28ath6kl: improve wmi debug messagesKalle Valo
Add a new debug level ATH6KL_DBG_WMI_DUMP and other minor improvements to the wmi debug messages. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2011-09-28ath6kl: add debug logs for bootingKalle Valo
Just to make it easier to find out why boot fails. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2011-09-28ath6kl: add sdio debug messagesKalle Valo
Add extensive debug messages to sdio.c. Makes it easier to debug various problems. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2011-09-28ath6kl: add prefix parameter to ath6kl_dbg_dump()Kalle Valo
Makes it easier to recognise longs dumps. Obligatory screenshot using "rx" prefix: ath6kl: ath6kl_rx rx 00000000: 10 10 00 00 00 00 08 30 00 00 00 00 00 00 f9 0b .......0........ rx 00000010: 2c 44 08 30 00 00 f9 0b 0c a4 02 00 00 00 73 d2 ,D.0..........s. rx 00000020: 94 00 f9 0b 04 8c 01 00 02 00 07 02 02 00 f9 0b ................ Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2011-09-28ath6kl: silence "invalid rate" warningKalle Valo
For some reason firmware is sending invalid rates when we try to query current bitrate from ath6kl_get_station() and a warning is issued: [ 3810.415720] ath6kl: invalid rate: 1935633515 [ 3811.105493] ath6kl: invalid rate: 1935633515 [ 3811.556063] ath6kl: invalid rate: 1935633515 As the warning happens way too often, convert the warning to a debug message once we have a proper fix. But to make it easy to follow how often the problem appears, add a debugfs to print various statistics about workarounds and make this issue the first WAR. Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
2011-09-28Merge branch 'master' of git://git.infradead.org/users/linville/wirelessJohn W. Linville
Conflicts: drivers/net/wireless/iwlwifi/iwl-scan.c net/wireless/nl80211.c
2011-09-27wl3501_cs: min_t() cast truncates high bitsDan Carpenter
wrqu->encoding.length comes from the network administrator. It's size u16. We want to limit "tocopy" to the smallest value of either "len_keys", "wrqu->encoding.length" or 100. But because .length gets cast from u16 to u8 we might use a random, smaller value than the was desired. It's probably not very serious, but we may as well fix it. Btw, this is from code auditing and not from testing. I don't know if this affects anyone in real life. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27iwlagn: fix scan complete processingJohannes Berg
When we cancel a scan, the completion runs only from the workqueue. This can cause the remain-on-channel scan to fail when another one was just canceled, because we're still aborting it. To fix this, run the completion inline with the lock still held before returning from iwl_scan_cancel_timeout(). Also, to avoid the scan complete work from completing a new scan prematurely, add a new STATUS_SCAN_COMPLETE bit. Reported-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Tested-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27iwlagn: move iwl_process_scan_complete upJohannes Berg
To make the next patch easier to read, move the function up, it'll be needed earlier in this file in the next patch. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27iwlagn: refactor scan completeJohannes Berg
We'll need to be able to run scan complete inline, not from the workqueue, so refactor it. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27iwlagn: make iwl_scan_cancel_timeout voidJohannes Berg
The return value of iwl_scan_cancel_timeout() isn't used anywhere, so let's just remove it. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27iwlagn: remove Kelvin supportJohannes Berg
Only 5150 series devices report their temperature in Kelvin, and for those we already convert it to Celsius when storing into priv->temperature, so there's no way priv->temperature will ever be in Kelvin. Remove support for this. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27iwlagn: fix slot programmingJohannes Berg
When an AP mode interface is added with a DTIM period of two, the slot programming is wrong. Fix it by taking into account the DTIM period. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27iwlagn: fix dangling scan requestJohannes Berg
If iwl_scan_initiate() fails for any reason, priv->scan_request and priv->scan_vif are left dangling. This can lead to a crash later when iwl_bg_scan_completed() tries to run a pending scan request. In practice, this seems to be very rare due to the STATUS_SCANNING check earlier. That check, however, is wrong -- it should allow a scan to be queued when a reset/roc scan is going on. When a normal scan is already going on, a new one can't be issued by mac80211, so that code can be removed completely. I introduced this bug when adding off-channel support in commit 266af4c745952e9bebf687dd68af58df553cb59d. Cc: stable@kernel.org [3.0] Reported-by: Peng Yan <peng.yan@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27iwlagn: use kcalloc when possible for array allocationEmmanuel Grumbach
As everybody knows kcalloc checks the multiplication is safe and that we don't run into overflow. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27iwlagn: update rate scaling with BA notificationsEmmanuel Grumbach
In the current code, the rate scaling isn't fed with statistics from the BA notifications. This is since my patch: iwlagn: reclaim the packets in transport layer Fix that. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27iwlagn: add debugging to show probe related info in scan notificationWey-Yi Guy
Add debugging to show the status of probe in scan notification to help debug probe related issues Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27iwlagn: set the sequence control from the transport layerEmmanuel Grumbach
Since all the queue logic has been moved to the transport layer, the sequence number is set in the transport layer. While doing that I forgot that the mac header is copied to the TB of the TX cmd in the upper layer before the call to the transport layer. So basically we used the sequence number from mac80211... This was fine for the first assocation but after the second, mac80211 resets its counters while we don't hence a shift that led to terrible impact on performance. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27iwlagn: sparse warning priv->temperature is signedEmmanuel Grumbach
Since priv->temperature is signed, we cannot use debugfs_create_u32 to refer to it. Use a regular debugfs file instead. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27iwlagn: remove warning in iwl_rx_handleEmmanuel Grumbach
Txid was used without being initialized. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27ath9k: fix a regression in ath9k_ps_restoreFelix Fietkau
After 'ath9k: optimize ath9k_ps_restore', it would only send the device to network sleep and not to full sleep anymore, potentially causing more battery drain. Reported-by: Vivek Natarajan <nataraja@qca.qualcomm.com> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27mwifiex: reset skb length before inserting to free queueAmitkumar Karwar
After handling command response, cmd skb is inserted into command free queue(which keeps track of availabile skbs) for reuse purpose. Skb length is not getting reset to zero here. This patch takes care of it. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27mwifiex: pass correct band parameter to ieee80211_channel_to_frequency()Amitkumar Karwar
ieee80211_channel_to_frequency() routine expects band parameter in the form of "enum ieee80211_band band". Currently driver specific band (BAND_A, BAND_AN etc.) is passed to the routine. This patch makes sure that correct parameter is passed. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27mwifiex: update bss band informationAmitkumar Karwar
In recent commit "mwifiex: use cfg80211 dynamic scan..." (7c6fa2a843..) scan table handling in driver is removed to make use of cfg80211 dynamic scan table. Now driver sends beacon buffers found in scanning directly to stack and parse the buffer for requested BSS only during association. Beacon buffer doesn't contain bss band information. Driver gets it from firmware in separate tlv (chan_band_tlv). Currently since we don't inform stack about bss bandinfo, there is an issue with 5GHz association. Use "priv" field of struct cfg80211_bss to store bandinfo. This fixes 5GHz association issue. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27mwifiex: fix 5GHz association issueAmitkumar Karwar
Sometimes association in 5GHz doesn't work. Dmesg log shows "Can not find requested SSID xyz" error message. Currently while preparing scan channel list for firmware Null entries are created for disabled channels. The routine which retrieves this list ignores channels after Null entry. Hence sometimes driver doesn't scan the channel of requested AP and association fails. The issue is fixed by avoiding those NULL entries. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27b43: LCN-PHY: minor clean upsRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-09-27b43: update dummy transmissionRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>