| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-x86 into cpus4096
|
|
|
|
Impact: cleanup
In particular, *map are deprecated, and you have to use the accessors
as *mask are const.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
To: Jeremy Fitzhardinge <jeremy@xensource.com>
|
|
Impact: cleanup
node_to_cpumask (and the blecherous node_to_cpumask_ptr which
contained a declaration) are replaced now everyone implements
cpumask_of_node.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (f75375s) Remove unnecessary and confusing initialization
hwmon: (it87) Properly decode -128 degrees C temperature
hwmon: (lm90) Document support for the MAX6648/6692 chips
hwmon: (abituguru3) Fix I/O error handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/willy/pci
* 'fixes-20090312' of git://git.kernel.org/pub/scm/linux/kernel/git/willy/pci:
PCIe: portdrv: call pci_disable_device during remove
pci: Fix typo in message while disabling HT MSI mapping
pci: don't disable too many HT MSI mapping
powerpc/pseries: The RPA PCI hotplug driver depends on EEH
PCIe: AER: during disable, check subordinate before walking
PCI: Add PCI quirk to disable L0s ASPM state for 82575 and 82598
|
|
STag zero is a special STag that allows consumers to access any bus
address without registering memory. The nes driver unfortunately
allows STag zero to be used even with QPs created by unprivileged
userspace consumers, which means that any process with direct verbs
access to the nes device can read and write any memory accessible to
the underlying PCI device (usually any memory in the system). Such
access is usually given for cluster software such as MPI to use, so
this is a local privilege escalation bug on most systems running this
driver.
The driver was using STag zero to receive the last streaming mode
data; to allow STag zero to be disabled for unprivileged QPs, the
driver now registers a special MR for this data.
Cc: <stable@kernel.org>
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
No software visible difference from revision A.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently we disable the Acer WMI backlight device if there is no ACPI
backlight device. As a result, we end up with no backlight device at all.
We should instead disable it if there is an ACPI device, as the other
laptop drivers do. This regression was introduced in febf2d9 ("Acer-WMI:
fingers off backlight if video.ko is serving this functionality").
Each laptop driver with backlight support got a similar change around
febf2d9. The changes to the other drivers look correct; see e.g.
a598c82f for a similar but correct change. The regression is also in
2.6.28.
Signed-off-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Acked-by: Thomas Renninger <trenn@suse.de>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Len Brown <len.brown@intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: <stable@kernel.org> [2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The s3cmci driver is calling s3c2410_dma_config with incorrect data for
the DCON register. The S3C2410_DCON_HWTRIG is implicit in the channel
configuration and the device selection of S3C2410_DCON_CH0_SDI is
incorrect as the DMA system may not select channel 0.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The 'battery remaining capacity' calculation in
drivers/power/ds2760_battery.c lacks a parameter check to a division
operation which causes the kernel to oops on my board.
[ 21.233750] Division by zero in kernel.
[ 21.237646] [<c002955c>] (__div0+0x0/0x20) from [<c012561c>] (Ldiv0+0x8/0x10)
[ 21.244816] [<c01bef34>] (ds2760_battery_read_status+0x0/0x2a4) from [<c01bf3a4>] (ds2760_battery_get_property+0x30/0xdc)
[ 21.255803] r8:c03a22c0 r7:c7886100 r6:00000009 r5:c782fe7c r4:c7886084
[ 21.262518] [<c01bf374>] (ds2760_battery_get_property+0x0/0xdc) from [<c01bde98>] (power_supply_show_property+0x48/0x114)
[ 21.273480] r6:c7996000 r5:00000009 r4:00000000
[ 21.278111] [<c01bde50>] (power_supply_show_property+0x0/0x114) from [<c01be158>] (power_supply_uevent+0x188/0x280)
[ 21.288537] r8:00000001 r7:c7886100 r6:c7996000 r5:000000b4 r4:00000000
[ 21.295222] [<c01bdfd0>] (power_supply_uevent+0x0/0x280) from [<c015c664>] (dev_uevent+0xd4/0x10c)
[ 21.304199] [<c015c590>] (dev_uevent+0x0/0x10c) from [<c0128440>] (kobject_uevent_env+0x180/0x390)
[ 21.313170] r5:00000000 r4:c78860ac
[ 21.316725] [<c01282c0>] (kobject_uevent_env+0x0/0x390) from [<c0128664>] (kobject_uevent+0x14/0x18)
[ 21.325850] [<c0128650>] (kobject_uevent+0x0/0x18) from [<c01bdc34>] (power_supply_changed_work+0x5c/0x70)
[ 21.335506] [<c01bdbd8>] (power_supply_changed_work+0x0/0x70) from [<c004d290>] (run_workqueue+0xbc/0x144)
[ 21.345167] r4:c7812040
[ 21.347716] [<c004d1d4>] (run_workqueue+0x0/0x144) from [<c004d94c>] (worker_thread+0xa8/0xbc)
[ 21.356296] r7:c7812040 r6:c7820b00 r5:c782ffa4 r4:c7812048
[ 21.361957] [<c004d8a4>] (worker_thread+0x0/0xbc) from [<c0051008>] (kthread+0x5c/0x94)
[ 21.369971] r7:00000000 r6:c004d8a4 r5:c7812040 r4:c782e000
[ 21.375612] [<c0050fac>] (kthread+0x0/0x94) from [<c00403d0>] (do_exit+0x0/0x688)
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Acked-by: Matt Reimer <mreimer@vpop.net>
Acked-by: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
W1 master implementations are expected to return 0 or 1 from their
read_bit() function. However, not all platforms do return these values
from gpio_get_value() - namely PXAs won't. Hence the w1 gpio-master needs
to break the result down to 0 or 1 itself.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The PCIe port driver calls pci_enable_device() during probe but
never calls pci_disable_device() during remove.
Cc: stable@kernel.org
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
|
|
"Enabling" should read "Disabling"
Signed-off-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
|
|
Prakash's system needs MSI disabled on some bridges, but not all.
This seems to be the minimal fix for 2.6.29, but should be replaced
during 2.6.30.
Signed-off-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
|
|
The RPA PCI hotplug driver calls EEH routines, so should depend on
EEH. Also PPC_PSERIES implies PPC64, so remove that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
|
|
Commit 47a8b0cc (Enable PCIe AER only after checking firmware
support) wants to walk the PCI bus in the remove path to disable
AER, and calls pci_walk_bus for downstream bridges.
Unfortunately, in the remove path, we remove devices and bridges
in a depth-first manner, starting with the furthest downstream
bridge and working our way backwards.
The furthest downstream bridges will not have a dev->subordinate,
and we hit a NULL deref in pci_walk_bus.
Check for dev->subordinate first before attempting to walk the
PCI hierarchy below us.
Acked-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
|
|
This patch is intended to disable L0s ASPM link state for 82598 (ixgbe)
parts due to the fact that it is possible to corrupt TX data when coming
back out of L0s on some systems. The workaround had been added for 82575
(igb) previously, but did not use the ASPM api. This quirk uses the ASPM
api to prevent the ASPM subsystem from re-enabling the L0s state.
Instead of adding the fix in igb to the ixgbe driver as well it was
decided to move it into a pci quirk. It is necessary to move the fix out
of the driver and into a pci quirk in order to prevent the issue from
occuring prior to driver load to handle the possibility of the device being
passed to a VM via direct assignment.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sunhme: Fix qfe parent detection.
sparc64: Fix lost interrupts on sun4u.
sparc64: wait_event_interruptible_timeout may return -ERESTARTSYS
jsflash: stop defining MAJOR_NR
|
|
f75375_probe calls i2c_get_clientdata to initialize the data pointer,
but there isn't yet any client data to get, and the value is never
used before the variable is assigned a new value seven lines later.
The call doesn't hurt anything and wastes only a couple of cycles.
The reason to fix it is because this module serves as an example to
hackers writing new hwmon drivers, and this part of the example is
confusing.
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The it87 driver is reporting -128 degrees C as +128 degrees C.
That's not a terribly likely temperature value but let's still
get it right, especially when it simplifies the code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Update documentation to prevent further confusion/duplication.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Fix a logic bug reported by Roel Kluin, by rewriting the error
handling code in a clearer way.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Alistair John Strachan <alistair@devzero.co.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
radeonfb/aty128fb: Disable broken early resume hook for PowerBooks
hvc_console: Remove tty->low_latency on pseries backends
powerpc: fix linkstation and storcenter compilation breakage
powerpc/4xx: Enable SERIAL_OF support by default for Virtex platforms
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: fix 945 fence register writes for fence 8 and above.
drm/i915: Protect active fences on i915
drm/i915: Check to see if we've pinned all available fences
drm/i915: Check fence status on every pin.
drm/i915: First recheck for an empty fence register.
drm/i915: Fix bad \n in MTRR failure notice.
drm/i915: Don't restore palettes through VGA registers.
i915: add newline to i915_gem_object_pin failure msg
drm: Return EINVAL on duplicate objects in execbuffer object list
|
|
The last 8 fence registers sit at a different offset, so when we went to set
fence number 8 in the lower offset, we instead set PGETBL_CTL, and the GPU
got all sorts of angry at us.
fd.o bug #20567. Easily reproducible by running glxgears and killing it about
6 times.
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
The i915 also uses the fence registers for GPU access to tiled buffers so
we cannot reallocate one whilst it is on the active list. By performing a
LRU scan of the fenced buffers we also avoid waiting the possibility of
waiting on a pinned, or otherwise unusable, buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
|
|
|
|
We need to check and report if there are no available fences - or else we
spin endlessly waiting for a buffer to magically unpin itself.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
As we may steal the fence register of an unpinned buffer for another,
every time we repin the buffer we need to recheck whether it needs to be
allocated a fence.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
If we wait upon a request and successfully unbind a buffer occupying a
fence register, then that slot will be freed and cause a NULL derefrence
upon rescanning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
radeonfb and aty128fb have a special hook called by the PowerMac platform
code very very early on resume from sleep to bring the screen back. This
is useful for debugging wakup problems, but unfortunately, this also became
a source of problems of its own.
The hook is called extremely early, with interrupts still off, and the code
path involved with that code nowadays rely on things like taking mutexes,
GFP_KERNEL allocations, etc...
In addition, the driver now relies on the PCI core to restore the standard
config space before calling resume which doesn't happen with this early
code path.
I'm keeping the code in but commented out along with a fixup call to
pci_restore_state(). The reason is that I still want to make it easy to
re-enable temporarily to track wake up problems, and it's possible that
I can revive it at some stage if we make sleeping things save to call
in early resume using a system state.
In the meantime, this should fix several reported regressions.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The hvcs and hvsi backends both set tty->low_latency to one, along
with more or less scary comments regarding bugs or races that would
happen if not doing so.
However, they also both call tty_flip_buffer_push() in conexts where
it's illegal to do so since some recent tty changes (or at least it
may have been illegal always but it nows blows) when low_latency is
set (ie, hard interrupt or with spinlock held and irqs disabled).
This removes the setting for now to get them back to working condition,
we'll have to address the races described in the comments separately
if they are still an issue (some of this might have been fixed already).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Prevent the kernel from being crashed by a divide-by-zero operation when
supplied an incorrectly filled 'struct fb_var_screeninfo' from userland.
Previously i810_main.c:1005 (i810_check_params) was using the global
'yres' symbol previously defined at i810_main.c:145 as a module parameter
value holder (i810_main.c:2174). If i810fb is compiled-in or if this
param doesn't get a default value, this direct usage leads to a
divide-by-zero at i810_main.c:1005 (i810_check_params). The patch simply
replace the 'yres' global, perhaps undefined symbol usage by a given
parameter structure lookup.
This problem occurs with directfb, mplayer -vo fbdev, SDL library.
It was also reported ( but non solved ) at:
http://mail.directfb.org/pipermail/directfb-dev/2008-March/004050.html
Signed-off-by: Samuel CUELLA <samuel.cuella@supinfo.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit e480814f138cd5d78a8efe397756ba6b6518fdb6 ("[MTD] [MAPS] physmap:
fix wrong free and del_mtd_{partition,device}") introduces a NULL pointer
dereference in physmap_flash_remove when called from the error path in
physmap_flash_probe (if map_probe failed).
Call del_mtd_{partition,device} only if info->cmtd was not NULL.
Reported-by: pHilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When GTT size is equal to amount of video memory, the amount of GTT
entries is computed lower than zero, which is invalid and leads to
off-by-one error in intel_i915_configure()
Originally posted here:
http://bugzilla.kernel.org/show_bug.cgi?id=12539
http://bugzilla.redhat.com/show_bug.cgi?id=445592
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Lubomir Rintel <lkundrak@v3.sk>
Cc: Dave Airlie <airlied@linux.ie>
Reviewed-by: Eric Anholt <eric@anholt.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 771999b65f79264acde4b855e5d35696eca5e80c ("[MTD] DataFlash: bugfix,
binary page sizes now handled") broke support for probing AT45DB321C flash
chips. These chips do not support the "page size" status bit, so if we
match the JEDEC id return early.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Will Newton <will.newton@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Impact: fix bug to make agp work with dri
Jeffrey reported that dri does work with 64bit, but doesn't work with
32bit it turns out NB aperture is 32M, aperture on agp is 128M
64bit is using 64M for vaidation for 64 iommu/gart 32bit is only using
32M..., and will not update the nb aperture.
So try to compare nb apterture and agp apterture before leaving not
touch nb aperture.
Reported-by: Jeffrey Trull <jetrull@sbcglobal.net>
Tested-by: Jeffrey Trull <jetrull@sbcglobal.net>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The adt7468 chip supports VRM10 sensors just like the adt7463; add a
missing check for it.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The verstep check in the lm85 driver fails because the upper nibble of
the version register is 0x7, not 0x6, on the adt7468 chip. Probing of
all adt7468s was broken by 69fc1feba2d5856ff74dedb6ae9d8c490210825c
("hwmon: (lm85) Rework the device detection"), and this patch fixes
that. Also add in a missing i2c_device_id that accidentally got dropped
from the original patch.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
get_nid_for_pfn() returns int
Presumably the (nid < 0) case has never happened.
We do know that it is happening on one system while creating a symlink for
a memory section so it should also happen on the same system if
unregister_mem_sect_under_nodes() were called to remove the same symlink.
The test was actually added in response to a problem with an earlier
version reported by Yasunori Goto where one or more of the leading pages
of a memory section on the 2nd node of one of his systems was
uninitialized because I believe they coincided with a memory hole.
That earlier version did not ignore uninitialized pages and determined
the nid by considering only the 1st page of each memory section. This
caused the symlink to the 1st memory section on the 2nd node to be
incorrectly created in /sys/devices/system/node/node0 instead of
/sys/devices/system/node/node1. The problem was fixed by adding the
test to skip over uninitialized pages.
I suspect we have not seen any reports of the non-removal
of a symlink due to the incorrect declaration of the nid
variable in unregister_mem_sect_under_nodes() because
- systems where a memory section could have an uninitialized
range of leading pages are probably rare.
- memory remove is probably not done very frequently on the
systems that are capable of demonstrating the problem.
- lingering symlink(s) that should have been removed may
have simply gone unnoticed.
[garyhade@us.ibm.com: wrote changelog]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
The VGA registers just hit the pipe registers that we already set through
MMIO. This fixes strange colors on resume.
Signed-off-by: Pierre Willenbrock <pierre@pirsoft.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
Prevents formatting nasty as below:
[drm:i915_gem_object_pin] *ERROR* Failure to bind: -12<3>[drm:i915_gem_evict_something] *ERROR* inactive empty 1 request empty 1 flushing empty 1
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
If userspace passes an object list with the same object appearing more
than once, we end up hitting the BUG_ON() in
i915_gem_object_set_to_gpu_domain() as it gets called a second time
for the same object.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
video: deferred io cleanup fix for sh_mobile_lcdcfb
sh: Add media/soc_camera.h to board setup of Renesas AP325RXA
|
|
'x86/urgent', 'linus' and 'core/percpu' into x86/core
|
|
Fix deferred io cleanup patch in the sh_mobile_lcdcfb driver.
If probe() fails early the sh_mobile_lcdc_stop() function will
be called to clean up deferred io. This patch modifies the
code to only call fb_deferred_io_cleanup() after deferred io
has been initialized.
With this patch applied we no longer hit BUG_ON() inside
fb_deferred_io_cleanup(). Triggers on a Migo-R with the
SYS QVGA panel board unmounted.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
* 'for-linus' of git://neil.brown.name/md:
md: fix deadlock when stopping arrays
|
