| Age | Commit message (Collapse) | Author |
|---|
|
dev_dbg() is used to print ordinary transfer messages in xhci-ring.c.
System log messages will be flushed if CONFIG_USB_DEBUG is set. Replace the
dev_dbg() with xhci_dbg().
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
giveback_first_trb() controls the cycle bit set of the start_trb, to ensure
that the start_trb is written last and the host controller will receive a
whole td at a time.
However, if the ring is wrapped and cycle bit is toggled to zero, then
giveback_first_trb() will be of no effect. In this case, set the cycle bit of
start_trb to 1 at the beginning and clear it in giveback_first_trb().
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
Parameter *td is not used in giveback_first_trb(). Remove it.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
Fix the more_trbs_coming field of queue_trb() in isoc transfer.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
When xhci_discover_or_reset_device() is called after a host controller
power loss, the virtual device may need to be reallocated. Make sure
xhci_alloc_dev() uses GFP_NOIO. This avoid causing a deadlock by allowing
the kernel to flush pending I/O while reallocating memory for a virtual
device for a USB mass storage device that's holding the backing store for
dirty memory buffers.
This patch should be queued for the 2.6.37 stable tree.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
|
|
When there's an xHCI host power loss after a suspend from memory, the USB
core attempts to reset and verify the USB devices that are attached to the
system. The xHCI driver has to reallocate those devices, since the
hardware lost all knowledge of them during the power loss.
When a hub is plugged in, and the host loses power, the xHCI hardware
structures are not updated to say the device is a hub. This is usually
done in hub_configure() when the USB hub is detected. That function is
skipped during a reset and verify by the USB core, since the core restores
the old configuration and alternate settings, and the hub driver has no
idea this happened. This bug makes the xHCI host controller reject the
enumeration of low speed devices under the resumed hub.
Therefore, make the USB core re-setup the internal xHCI hub device
information by calling update_hub_device() when hub_activate() is called
for a hub reset resume. After a host power loss, all devices under the
roothub get a reset-resume or a disconnect.
This patch should be queued for the 2.6.37 stable tree.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
|
|
when unloading xhci_hcd, I got:
[ 134.856813] xhci_hcd 0000:02:00.0: remove, state 4
[ 134.858140] usb usb3: USB disconnect, address 1
[ 134.874956] xhci_hcd 0000:02:00.0: Host controller not halted, aborting reset.
[ 134.876351] BUG: sleeping function called from invalid context at kernel/mutex.c:85
[ 134.877657] in_atomic(): 0, irqs_disabled(): 1, pid: 1451, name: modprobe
[ 134.878975] Pid: 1451, comm: modprobe Not tainted 2.6.37-rc5+ #162
[ 134.880298] Call Trace:
[ 134.881602] [<ffffffff8104156a>] __might_sleep+0xeb/0xf0
[ 134.882921] [<ffffffff814763dc>] mutex_lock+0x24/0x50
[ 134.884229] [<ffffffff810a745c>] free_desc+0x2e/0x5f
[ 134.885538] [<ffffffff810a74c8>] irq_free_descs+0x3b/0x71
[ 134.886853] [<ffffffff8102584d>] free_irq_at+0x31/0x36
[ 134.888167] [<ffffffff8102723f>] destroy_irq+0x69/0x71
[ 134.889486] [<ffffffff8102747a>] native_teardown_msi_irq+0xe/0x10
[ 134.890820] [<ffffffff8124c382>] default_teardown_msi_irqs+0x57/0x80
[ 134.892158] [<ffffffff8124be46>] free_msi_irqs+0x8b/0xe9
[ 134.893504] [<ffffffff8124cd46>] pci_disable_msix+0x35/0x39
[ 134.894844] [<ffffffffa01b444a>] xhci_cleanup_msix+0x31/0x51 [xhci_hcd]
[ 134.896186] [<ffffffffa01b4b3a>] xhci_stop+0x3a/0x80 [xhci_hcd]
[ 134.897521] [<ffffffff81341dd4>] usb_remove_hcd+0xfd/0x14a
[ 134.898859] [<ffffffff813500ae>] usb_hcd_pci_remove+0x5c/0xc6
[ 134.900193] [<ffffffff8123c606>] pci_device_remove+0x3f/0x91
[ 134.901535] [<ffffffff812e7ea4>] __device_release_driver+0x83/0xd9
[ 134.902899] [<ffffffff812e8571>] driver_detach+0x86/0xad
[ 134.904222] [<ffffffff812e7d56>] bus_remove_driver+0xb2/0xd8
[ 134.905540] [<ffffffff812e8633>] driver_unregister+0x6c/0x74
[ 134.906839] [<ffffffff8123c8e4>] pci_unregister_driver+0x44/0x89
[ 134.908121] [<ffffffffa01b940e>] xhci_unregister_pci+0x15/0x17 [xhci_hcd]
[ 134.909396] [<ffffffffa01bd7d2>] xhci_hcd_cleanup+0xe/0x10 [xhci_hcd]
[ 134.910652] [<ffffffff8107fcd1>] sys_delete_module+0x1ca/0x23b
[ 134.911882] [<ffffffff81123932>] ? path_put+0x22/0x26
[ 134.913104] [<ffffffff8109a800>] ? audit_syscall_entry+0x2c/0x148
[ 134.914333] [<ffffffff8100ac82>] system_call_fastpath+0x16/0x1b
[ 134.915658] xhci_hcd 0000:02:00.0: USB bus 3 deregistered
[ 134.916465] xhci_hcd 0000:02:00.0: PCI INT A disabled
and the same issue when xhci_suspend is invoked. (Note from Sarah: That's
fixed by Andiry's patch before this, by synchronizing the irqs rather than
freeing them on suspend.)
Do not run xhci_cleanup_msix with irq disabled.
This patch should be queued for the 2.6.37 stable tree.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
|
|
Synchronize the interrupts instead of free them in xhci_suspend(). This will
prevent a double free when the host is suspended and then the card removed.
Set the flag hcd->msix_enabled when using MSI-X, and check the flag in
suspend_common(). MSI-X synchronization will be handled by xhci_suspend(),
and MSI/INTx will be synchronized in suspend_common().
This patch should be queued for the 2.6.37 stable tree.
Reported-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
|
|
The original code that resumed the USB bus on a port status change would
only do so when there was a device connected to the port. If a device was
just disconnected, the event would be queued for khubd, but khubd wouldn't
run. That would leave the connect status change (CSC) bit set.
If a USB device was plugged into that same port, the xHCI host controller
would set the current connect status (CCS) bit. But since the CSC bit was
already set, it would not generate an interrupt for a port status change
event. That would mean the user could "Safely Remove" a device, have the
bus suspend, disconnect the device, re-plug it in, and then the device
would never be enumerated.
Plugging in a different device on another port would cause the bus to
resume, and khubd would notice the re-connected device. Running lsusb
would also resume the bus, leading users to report the problem "went away"
when using diagnostic tools.
The solution is to resume the bus when a port status change event is
received, regardless of the port status.
Thank you very much to Maddog for helping me track down this Heisenbug.
This patch should be queued for the 2.6.37 stable tree.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Jon 'maddog' Hall <maddog@li.org>
Tested-by: Andiry Xu <andiry.xu@amd.com>
Cc: stable@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (30 commits)
MAINTAINERS: Add tomoyo-dev-en ML.
SELinux: define permissions for DCB netlink messages
encrypted-keys: style and other cleanup
encrypted-keys: verify datablob size before converting to binary
trusted-keys: kzalloc and other cleanup
trusted-keys: additional TSS return code and other error handling
syslog: check cap_syslog when dmesg_restrict
Smack: Transmute labels on specified directories
selinux: cache sidtab_context_to_sid results
SELinux: do not compute transition labels on mountpoint labeled filesystems
This patch adds a new security attribute to Smack called SMACK64EXEC. It defines label that is used while task is running.
SELinux: merge policydb_index_classes and policydb_index_others
selinux: convert part of the sym_val_to_name array to use flex_array
selinux: convert type_val_to_struct to flex_array
flex_array: fix flex_array_put_ptr macro to be valid C
SELinux: do not set automatic i_ino in selinuxfs
selinux: rework security_netlbl_secattr_to_sid
SELinux: standardize return code handling in selinuxfs.c
SELinux: standardize return code handling in selinuxfs.c
SELinux: standardize return code handling in policydb.c
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (44 commits)
hwmon: Support for Dallas Semiconductor DS620
hwmon: driver for Sensirion SHT21 humidity and temperature sensor
hwmon: Add humidity attribute to sysfs ABI
hwmon: sysfs ABI updates
hwmon: (via-cputemp) sync hotplug handling with coretemp/pkgtemp
hwmon: (lm95241) Rewrite to avoid using macros
hwmon: (applesmc) Fix checkpatch errors and fix value range checks
hwmon: (applesmc) Update copyright information
hwmon: (applesmc) Silence driver
hwmon: (applesmc) Simplify feature sysfs handling
hwmon: (applesmc) Dynamic creation of fan files
hwmon: (applesmc) Extract all features generically
hwmon: (applesmc) Handle new temperature format
hwmon: (applesmc) Dynamic creation of temperature files
hwmon: (applesmc) Introduce a register lookup table
hwmon: (applesmc) Use pr_fmt and pr_<level>
hwmon: (applesmc) Relax the severity of device init failure
hwmon: (applesmc) Add MacBookAir3,1(3,2) support
hwmon: (w83627hf) Use pr_fmt and pr_<level>
hwmon: (w83627ehf) Use pr_fmt and pr_<level>
...
|
|
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (29 commits)
of/flattree: forward declare struct device_node in of_fdt.h
ipmi: explicitly include of_address.h and of_irq.h
sparc: explicitly cast negative phandle checks to s32
powerpc/405: Fix missing #{address,size}-cells in i2c node
powerpc/5200: dts: refactor dts files
powerpc/5200: dts: Change combatible strings on localbus
powerpc/5200: dts: remove unused properties
powerpc/5200: dts: rename nodes to prepare for refactoring dts files
of/flattree: Update dtc to current mainline.
of/device: Don't register disabled devices
powerpc/dts: fix syntax bugs in bluestone.dts
of: Fixes for OF probing on little endian systems
of: make drivers depend on CONFIG_OF instead of CONFIG_PPC_OF
of/flattree: Add of_flat_dt_match() helper function
of_serial: explicitly include of_irq.h
of/flattree: Refactor unflatten_device_tree and add fdt_unflatten_tree
of/flattree: Reorder unflatten_dt_node
of/flattree: Refactor unflatten_dt_node
of/flattree: Add non-boottime device tree functions
of/flattree: Add Kconfig for EARLY_FLATTREE
...
Fix up trivial conflict in arch/sparc/prom/tree_32.c as per Grant.
|
|
Remove kobject.h from files which don't need it, notably,
sched.h and fs.h.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/bug-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/event: validate irq before get evtchn by irq
xen/fb: fix potential memory leak
xen/fb: fix xenfb suspend/resume race.
xen: disable ACPI NUMA for PV guests
xen/irq: Cleanup the find_unbound_irq
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_platform: Remove CONFIG_HAVE_PATA_PLATFORM's dependencies.
pata_hpt37x: actually limit HPT370 to UltraDMA/66
pata_hpt3x2n: coding style cleanup
pata_hpt37x: coding style cleanup
pata_hpt366: coding style cleanup
pata_hpt3x2n: calculate average f_CNT
pata_hpt3x2n: clarify about HPT371N support
pata_hpt{37x|3x2n}: SATA mode filtering
[libata] avoid needlessly passing around ptr to SCSI completion func
[libata] new driver acard_ahci, for ATP8620 host controller
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (34 commits)
HID: roccat: Update sysfs attribute doc
HID: roccat: don't use #pragma pack
HID: roccat: Add support for Roccat Kone[+] v2
HID: roccat: reduce number of functions in kone and pyra drivers
HID: roccat: declare meaning of pack pragma usage in driver headers
HID: roccat: use class for char device for sysfs attribute creation
sysfs: Introducing binary attributes for struct class
HID: hidraw: add compatibility ioctl() for 32-bit applications.
HID: hid-picolcd: Fix memory leak in picolcd_debug_out_report()
HID: picolcd: fix misuse of logical operation in place of bitop
HID: usbhid: base runtime PM on modern API
HID: replace offsets values with their corresponding BTN_* defines
HID: hid-mosart: support suspend/resume
HID: hid-mosart: ignore buttons report
HID: hid-picolcd: don't use flush_scheduled_work()
HID: simplify an index check in hid_lookup_collection
HID: Hoist assigns from ifs
HID: Remove superfluous __inline__
HID: Use vzalloc for vmalloc/memset(,0...)
HID: Add and use hid_<level>: dev_<level> equivalents
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
spi / PM: Support dev_pm_ops
PM: Prototype the pm_generic_ operations
PM / Runtime: Generic resume shouldn't set RPM_ACTIVE unconditionally
PM: Use dev_name() in core device suspend and resume routines
PM: Permit registration of parentless devices during system suspend
PM: Replace the device power.status field with a bit field
PM: Remove redundant checks from core device resume routines
PM: Use a different list of devices for each stage of device suspend
PM: Avoid compiler warning in pm_noirq_op()
PM: Use pm_wakeup_pending() in __device_suspend()
PM / Wakeup: Replace pm_check_wakeup_events() with pm_wakeup_pending()
PM: Prevent dpm_prepare() from returning errors unnecessarily
PM: Fix references to basic-pm-debugging.txt in drivers-testing.txt
PM / Runtime: Add synchronous runtime interface for interrupt handlers (v3)
PM / Hibernate: When failed, in_suspend should be reset
PM / Hibernate: hibernation_ops->leave should be checked too
Freezer: Fix a race during freezing of TASK_STOPPED tasks
PM: Use proper ccflag flag in kernel/power/Makefile
PM / Runtime: Fix comments to match runtime callback code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: use split transaction timeout only for split transactions
firewire: ohci: consolidate context status flags
firewire: ohci: cache the context run bit
firewire: ohci: flush AT contexts after bus reset - addendum
firewire: ohci: flush AT contexts after bus reset for OHCI 1.2
firewire: net: set carrier state at ifup
firewire: net: add carrier detection
firewire: net: ratelimit error messages
firewire: ohci: restart iso DMA contexts on resume from low power mode
firewire: ohci: restore GUID on resume.
firewire: ohci: use common buffer for self IDs and AR descriptors
firewire: ohci: optimize iso context checks in the interrupt handler
firewire: make PHY packet header format consistent
firewire: ohci: properly clear posted write errors
firewire: ohci: flush MMIO writes in the interrupt handler
firewire: ohci: fix AT context initialization error handling
firewire: ohci: Asynchronous Reception rewrite
firewire: core: Update WARN uses
firewire: nosy: char device is not seekable
|
|
When retrieving the event channel number from irq, the irq
number may not be valid under some conditions.
So far that can be when we suspend/resume and irq ends with -1.
Validate and return sanitized irq and provide diagnostics information.
[v3: added unlikely on the WARN path]
[v2: reworded the commit message]
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Gurudas Pai <gurudas.pai@oracle.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
|
|
This patch fixes a potential memory leak when xenfb connect to
the backend fails.
Thanks for Ian's review and comments.
[v2: reworded the commit message a bit]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Tested-by: Gurudas Pai <gurudas.pai@oracle.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
|
|
When migrating guests over a long period we hit this:
<1>BUG: unable to handle kernel paging request at 0000000b819fdb98
<1>IP: [<ffffffff812a588f>] notify_remote_via_irq+0x13/0x34
<4>PGD 94b10067 PUD 0
<0>Oops: 0000 [#1] SMP
.. snip..
Call Trace:
[<ffffffff812712c9>] xenfb_send_event+0x5c/0x5e
[<ffffffff8100ea5f>] ? xen_restore_fl_direct_end+0x0/0x1
[<ffffffff81438d80>] ? _spin_unlock_irqrestore+0x16/0x18
[<ffffffff812714ee>] xenfb_refresh+0x1b1/0x1d7
[<ffffffff81270568>] ? sys_imageblit+0x1ac/0x458
[<ffffffff81271786>] xenfb_imageblit+0x2f/0x34
[<ffffffff8126a3e5>] soft_cursor+0x1b5/0x1c8
[<ffffffff8126a137>] bit_cursor+0x4b6/0x4d7
[<ffffffff8100ea5f>] ? xen_restore_fl_direct_end+0x0/0x1
[<ffffffff81438d80>] ? _spin_unlock_irqrestore+0x16/0x18
[<ffffffff81269c81>] ? bit_cursor+0x0/0x4d7
[<ffffffff812656b7>] fb_flashcursor+0xff/0x111
[<ffffffff812655b8>] ? fb_flashcursor+0x0/0x111
[<ffffffff81071812>] worker_thread+0x14d/0x1ed
[<ffffffff81075a8c>] ? autoremove_wake_function+0x0/0x3d
[<ffffffff81438d80>] ? _spin_unlock_irqrestore+0x16/0x18
[<ffffffff810716c5>] ? worker_thread+0x0/0x1ed
[<ffffffff810756e3>] kthread+0x6e/0x76
[<ffffffff81012dea>] child_rip+0xa/0x20
[<ffffffff81011fd1>] ? int_ret_from_sys_call+0x7/0x1b
[<ffffffff8101275d>] ? retint_restore_args+0x5/0x6
[<ffffffff81012de0>] ? child_rip+0x0/0x20
Code: 6b ff 0c 8b 87 a4 db 9f 81 66 85 c0 74 08 0f b7 f8 e8 3b ff ff ff c9
c3 55 48 89 e5 48 83 ec 10 0f 1f 44 00 00 89 ff 48 6b ff 0c <8b> 87 a4 db 9f
81 66 85 c0 74 14 48 8d 75 f0 0f b7 c0 bf 04 00
RIP [<ffffffff812a588f>] notify_remote_via_irq+0x13/0x34
RSP <ffff8800e7bf7bd0>
CR2: 0000000b819fdb98
---[ end trace 098b4b74827595d0 ]---
The root cause of the panic is the race between the resume and reconnect to the backend.
Clearing the 'update_wanted' flag of xenfb before disconnecting from the
backend fixes this issue.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Gurudas Pai <gurudas.pai@oracle.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
|
|
Conflicts:
security/smack/smack_lsm.c
Verified and added fix by Stephen Rothwell <sfr@canb.auug.org.au>
Ok'd by Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
Driver for Dallas Semiconductor DS620 temperature sensor and thermostat
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Signed-off-by: Urs Fleisch <urs.fleisch@sensirion.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Signed-off-by: Davide Rizzo <elpa.rizzo@gmail.com>
[guenter.roeck@ericsson.com: Formatting changes]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
This patch fixes all checkpatch errors and most of the checkpatch warnings.
It also fixes the range check in applesmc_store_fan_speed().
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
|
|
With the preceding patches, git blame assigns about half of
the file to the present author. Add a line to the copyright
to reflect this.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Make the driver report a single line on success.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Given the dynamic node construction method, the setup of the
accelerometer, light sensor and keyboard backlight sysfs nodes
can be simplified. This patch does not contain any logic changes.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
With the dynamic temperature group in place, the setup of fans
can be simplified. This patch sets up the fans dynamically, removing
a hundred lines of code.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
With temperature keys being determined automatically, the dmi match
data is only used to assign features that can easily be detected from
the smc. This patch removes the dmi match data altogether, and reduces
the match table to the main machine models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
The recent Macbooks have temperature registers of a new type.
This patch adds the logic to handle them.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
The current driver creates temperature files based on a list
of temperature keys given per device. Apart from slow adaption
to new machine models, the number of sensors also depends on
the number of processors. This patch looks up the temperature
keys dynamically, thereby supporting all models.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
One main problem with the current driver is the inability to quickly
search for supported keys, resulting in detailed feature maps per
machine model which are cumbersome to maintain.
This patch adds a register lookup table, which enables binary search
for supported keys. The lookup also reduces the io frequency, so the
original mutex is replaced by locks around the actual io.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
[guenter.roeck@ericsson.com: Added value range check to key_at_index_store()]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
The device init is used to reset the accelerometer. Failure to reset
is not severe enough to stop loading the module or to resume from
hibernation. This patch relaxes failure to a warning and drops
output in case of success.
Cc: stable@kernel.org
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
This patch add support for the MacBookAir3,1 and MacBookAir3,2 to the
applesmc driver.
[rydberg@euromail.se: minor cleanup]
Cc: stable@kernel.org
Signed-off-by: Edgar Hucek <gimli@dark-green.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Added #define pr_fmt KBUILD_MODNAME ": " fmt
Converted printks to pr_<level>
Coalesced any long formats
Removed prefixes from formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
