| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit e37f14a5fb85522f3bbf88ece6134c4e610ed598.
It turned out other systems also share the same problem with bug 63111
so I made a patch to catch initial brightness level 0 problem. With that
patch applied, we do not need to place HP 250 G1 in DMI table.
References: https://bugzilla.kernel.org/show_bug.cgi?id=63111
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some firmware doesn't initialize initial backlight level to a proper
value and _BQC will return 0 on first time evaluation. We used to be
able to detect such incorrect value with our code logic, as value 0
normally isn't a valid value in _BCL. But with the introduction of Win8,
firmware begins to fill _BCL with values from 0 to 100, now 0 becomes
a valid value but that value will make user's screen black. This patch
test initial _BQC for value 0, if such a value is returned, do not use
it.
References: https://bugzilla.kernel.org/show_bug.cgi?id=64031
References: https://bugzilla.kernel.org/show_bug.cgi?id=61231
References: https://bugzilla.kernel.org/show_bug.cgi?id=63111
Reported-by: Qingshuai Tian <qingshuai.tian@intel.com>
Tested-by: Aaron Lu <aaron.lu@intel.com> # on "Idealpad u330p"
Reported-and-tested-by: <erno@iki.fi> # on "Acer Aspire V5-573G"
Reported-and-tested-by: Kirill Tkhai <tkhai@yandex.ru> # on "HP 250 G1"
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When testing if the firmware's initial value is valid, we should use
the corrected level value instead of the raw value returned from
firmware.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
That is the advertised name.
http://shop.lenovo.com/us/en/laptops/thinkpad/edge-series/e530/
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch adds Toshiba NB100 to the Vista _OSI blacklist.
The _OSI(Windows 2006) method is bugged on the netbook resulting in
messed up PCI IRQ Routing information. This was observed on a netbook
whose SATA controller mode was set to Compatibility mode.
The controller would then issue IRQs to IRQ#16 instead of
IRQ#20, where it should have been.
No side-effects were found during testing, everything is
working as it did before.
References: http://marc.info/?t=137862230200001&r=1&w=2
References: http://www.spinics.net/lists/linux-ide/msg46173.html
Signed-off-by: Levente Kurusa <levex@linux.com>
Reviewed-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
On HP 250 G1 laptops, BIOS reports minimum backlight on boot and
causes backlight to dim completely. This ignores the initial backlight
values and set to max brightness.
References: https://bugzilla.kernel.org/show_bug.cgi?id=63111
Signed-off-by: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
On the Yoga 13 the backlight control doesn't work via ACPI. (And doesn't
work either with the low-level platform driver ideapad_laptop; but
works correctly via the intel video driver). This patch hence adds the
Yoga 13 to the ACPI video detect blacklist, to make sure the broken ACPI
backlight device is never exposed to userspace.
Note that this appears unrelated to the Windows 8 backlight issues tracked
here:
https://bugzilla.kernel.org/show_bug.cgi?id=51231
https://bugzilla.kernel.org/show_bug.cgi?id=60682
The Yoga's ACPI backlight controls work neither with nor without
acpi_osi="!Windows 2012" on the kernel command line. It appears that
backlight control via the EC simply is not available at all, regardless
whether done via ACPI or via the vendor driver.
Signed-off-by: Lennart Poettering <lennart@poettering.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The tpacpi_acpi_handle_locate function makes use of acpi_get_devices to
locate handle for ACPI video by HID, the problem is, ACPI video node
doesn't really have HID defined(i.e. no _HID control method is defined
for video device), so.. that function would fail. This can be solved by
enhancing the callback function for acpi_get_devices, where we can use
acpi_device_hid function to check if the ACPI node corresponds to a
video controller.
In addition to that, the _BCL control method only exists under a video
output device node, not a video controller device node. So to evaluate
_BCL, we need the handle of a video output device node, which is child
of the located video controller node from tpacpi_acpi_handle_locate.
The two fix are necessary for some Thinkpad models to emit notification
on backlight hotkey press as a result of evaluation of _BCL.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
According to Matthew Garrett, "Windows 8 leaves backlight control up
to individual graphics drivers rather than making ACPI calls itself.
There's plenty of evidence to suggest that the Intel driver for
Windows [8] doesn't use the ACPI interface, including the fact that
it's broken on a bunch of machines when the OS claims to support
Windows 8. The simplest thing to do appears to be to disable the
ACPI backlight interface on these systems".
So for Win8 systems, if there is native backlight control interface
registered by GPU driver, ACPI video does not need to register its own.
Since there are systems that don't work well with this approach, a
parameter for video module named use_native_backlight is introduced and
has the value of false by default. For users who have a broken ACPI
video backlight interface, video.use_native_backlight=1 is needed in
kernel cmdline.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The backlight control and event delivery functionality provided by ACPI
video module is mixed together and registered all during video device
enumeration time. As a result, the two functionality are also removed
together on module unload time or by the acpi_video_unregister function.
The two functionalities are actually independent and one may be useful
while the other one may be broken, so it is desirable to seperate the
two functionalities such that it is clear and easy to disable one
functionality without affecting the other one.
APIs to selectively remove backlight control interface and/or event
delivery functionality can be easily added once needed.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Introduce a new API for modules to query if a specific type of backlight
device has been registered. This is useful for some backlight device
provider module (e.g. ACPI video) to know if a native control
interface(e.g. the interface created by i915) is available and then do
things accordingly (e.g. avoid registering its own on Win8 systems).
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In my original patch[1] I wrote a comment describing the reason for
disabling Windows 2012 OSI mode for a group of machines, however, due to
unknown reasons (probably a conflict resolution mismatch), the comment
was dropped in 94fb982 (ACPI: blacklist win8 OSI for buggy laptops).
Since Matthew Garrett is making a big deal out of the lack of comments
in a separate patch[2], it might make sense to re-introduce the missing
comment so that other patch is not blocked and users don't suffer.
[1] http://article.gmane.org/gmane.linux.acpi.devel/63427
[2] http://thread.gmane.org/gmane.linux.kernel/1572459
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
More people have reported they need this for their machines to work
correctly.
References: https://bugzilla.kernel.org/show_bug.cgi?id=60682
Reported-by: Stefan Hellermann <bugzilla.kernel.org@the2masters.de>
Reported-by: Benedikt Sauer <filmor@gmail.com>
Reported-by: Erno Kuusela <erno@iki.fi>
Reported-by: Jonathan Doman <jonathan.doman@gmail.com>
Reported-by: Christoph Klaffl <christophklaffl@gmail.com>
Reported-by: Jan Hendrik Nielsen <jan.hendrik.nielsen@informatik.hu-berlin.de>
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the outstanding target fixes queued up for v3.12-rc4 code.
The highlights include:
- Make vhost/scsi tag percpu_ida_alloc() use GFP_ATOMIC
- Allow sess_cmd_map allocation failure fallback to use vzalloc
- Fix COMPARE_AND_WRITE se_cmd->data_length bug with FILEIO backends
- Fixes for COMPARE_AND_WRITE callback recursive failure OOPs + non
zero scsi_status bug
- Make iscsi-target do acknowledgement tag release from RX context
- Setup iscsi-target with extra (cmdsn_depth / 2) percpu_ida tags
Also included is a iscsi-target patch CC'ed for v3.10+ that avoids
legacy wait_for_task=true release during fast-past StatSN
acknowledgement, and two other SRP target related patches that address
long-standing issues that are CC'ed for v3.3+.
Extra thanks to Thomas Glanzmann for his testing feedback with
COMPARE_AND_WRITE + EXTENDED_COPY VAAI logic"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target; Allow an extra tag_num / 2 number of percpu_ida tags
iscsi-target: Perform release of acknowledged tags from RX context
iscsi-target: Only perform wait_for_tasks when performing shutdown
target: Fail on non zero scsi_status in compare_and_write_callback
target: Fix recursive COMPARE_AND_WRITE callback failure
target: Reset data_length for COMPARE_AND_WRITE to NoLB * block_size
ib_srpt: always set response for task management
target: Fall back to vzalloc upon ->sess_cmd_map kzalloc failure
vhost/scsi: Use GFP_ATOMIC with percpu_ida_alloc for obtaining tag
ib_srpt: Destroy cm_id before destroying QP.
target: Fix xop->dbl assignment in target_xcopy_parse_segdesc_02
|
|
Pull slave-dmaengine fixes from Vinod Koul:
"Here is the slave dmanegine fixes. We have the fix for deadlock issue
on imx-dma by Michael and Josh's edma config fix along with author
change"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: imx-dma: fix callback path in tasklet
dmaengine: imx-dma: fix lockdep issue between irqhandler and tasklet
dmaengine: imx-dma: fix slow path issue in prep_dma_cyclic
dma/Kconfig: Make TI_EDMA select TI_PRIV_EDMA
edma: Update author email address
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Two patches for the OMAP driver, dealing with setting up IRQs properly
on the device tree boot path"
* tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio/omap: auto-setup a GPIO when used as an IRQ
gpio/omap: maintain GPIO and IRQ usage separately
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are none fixes for various USB driver problems. The majority are
gadget/musb fixes, but there are some new device ids in here as well"
* tag 'usb-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: chipidea: add Intel Clovertrail pci id
usb: gadget: s3c-hsotg: fix can_write limit for non-periodic endpoints
usb: gadget: f_fs: fix error handling
usb: musb: dsps: do not bind to "musb-hdrc"
USB: serial: option: Ignore card reader interface on Huawei E1750
usb: musb: gadget: fix otg active status flag
usb: phy: gpio-vbus: fix deferred probe from __init
usb: gadget: pxa25x_udc: fix deferred probe from __init
usb: musb: fix otg default state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty fixes from Greg KH:
"Here are two tty driver fixes for 3.12-rc4.
One fixes the reported regression in the n_tty code that a number of
people found recently, and the other one fixes an issue with xen
consoles that broke in 3.10"
* tag 'tty-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
xen/hvc: allow xenboot console to be used again
tty: Fix pty master read() after slave closes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are 4 tiny staging and iio driver fixes for 3.12-rc4. Nothing
major, just some small fixes for reported issues"
* tag 'staging-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: ni_65xx: (bug fix) confine insn_bits to one subdevice
iio:magnetometer: Bugfix magnetometer default output registers
iio: Remove debugfs entries in iio_device_unregister()
iio: amplifiers: ad8366: Remove regulator_put
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- The resume part of user space driven hibernation (s2disk) is now
broken after the change that moved the creation of memory bitmaps to
after the freezing of tasks, because I forgot that the resume utility
loaded the image before freezing tasks and needed the bitmaps for
that. The fix adds special handling for that case.
- One of recent commits changed the export of acpi_bus_get_device() to
EXPORT_SYMBOL_GPL(), which was technically correct but broke existing
binary modules using that function including one in particularly
widespread use. Change it back to EXPORT_SYMBOL().
- The intel_pstate driver sometimes fails to disable turbo if its
no_turbo sysfs attribute is set. Fix from Srinivas Pandruvada.
- One of recent cpufreq fixes forgot to update a check in cpufreq-cpu0
which still (incorrectly) treats non-NULL as non-error. Fix from
Philipp Zabel.
- The SPEAr cpufreq driver uses a wrong variable type in one place
preventing it from catching errors returned by one of the functions
called by it. Fix from Sachin Kamat.
* tag 'pm+acpi-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: Use EXPORT_SYMBOL() for acpi_bus_get_device()
intel_pstate: fix no_turbo
cpufreq: cpufreq-cpu0: NULL is a valid regulator, part 2
cpufreq: SPEAr: Fix incorrect variable type
PM / hibernate: Fix user space driven resume regression
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"A couple of fixes from the IOMMU side:
- some small fixes for the new ARM-SMMU driver
- a register offset correction for VT-d
- add MAINTAINERS entry for drivers/iommu
Overall no really big or intrusive changes"
* tag 'iommu-fixes-v3.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
x86/iommu: correct ICS register offset
MAINTAINERS: add overall IOMMU section
iommu/arm-smmu: don't enable SMMU device until probing has completed
iommu/arm-smmu: fix iommu_present() test in init
iommu/arm-smmu: fix a signedness bug
|
|
We need to free the ld_active list head before jumping into the callback
routine. Otherwise the callback could run into issue_pending and change
our ld_active list head we just going to free. This will run the channel
list into an currupted and undefined state.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The tasklet and irqhandler are using spin_lock while other routines are
using spin_lock_irqsave/restore. This leads to lockdep issues as
described bellow. This patch is changing the code to use
spinlock_irq_save/restore in both code pathes.
As imxdma_xfer_desc always gets called with spin_lock_irqsave lock held,
this patch also removes the spare call inside the routine to avoid
double locking.
[ 403.358162] =================================
[ 403.362549] [ INFO: inconsistent lock state ]
[ 403.366945] 3.10.0-20130823+ #904 Not tainted
[ 403.371331] ---------------------------------
[ 403.375721] inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
[ 403.381769] swapper/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
[ 403.386762] (&(&imxdma->lock)->rlock){?.-...}, at: [<c019d77c>] imxdma_tasklet+0x20/0x134
[ 403.395201] {IN-HARDIRQ-W} state was registered at:
[ 403.400108] [<c004b264>] mark_lock+0x2a0/0x6b4
[ 403.404798] [<c004d7c8>] __lock_acquire+0x650/0x1a64
[ 403.410004] [<c004f15c>] lock_acquire+0x94/0xa8
[ 403.414773] [<c02f74e4>] _raw_spin_lock+0x54/0x8c
[ 403.419720] [<c019d094>] dma_irq_handler+0x78/0x254
[ 403.424845] [<c0061124>] handle_irq_event_percpu+0x38/0x1b4
[ 403.430670] [<c00612e4>] handle_irq_event+0x44/0x64
[ 403.435789] [<c0063a70>] handle_level_irq+0xd8/0xf0
[ 403.440903] [<c0060a20>] generic_handle_irq+0x28/0x38
[ 403.446194] [<c0009cc4>] handle_IRQ+0x68/0x8c
[ 403.450789] [<c0008714>] avic_handle_irq+0x3c/0x48
[ 403.455811] [<c0008f84>] __irq_svc+0x44/0x74
[ 403.460314] [<c0040b04>] cpu_startup_entry+0x88/0xf4
[ 403.465525] [<c02f00d0>] rest_init+0xb8/0xe0
[ 403.470045] [<c03e07dc>] start_kernel+0x28c/0x2d4
[ 403.474986] [<a0008040>] 0xa0008040
[ 403.478709] irq event stamp: 50854
[ 403.482140] hardirqs last enabled at (50854): [<c001c6b8>] tasklet_action+0x38/0xdc
[ 403.489954] hardirqs last disabled at (50853): [<c001c6a0>] tasklet_action+0x20/0xdc
[ 403.497761] softirqs last enabled at (50850): [<c001bc64>] _local_bh_enable+0x14/0x18
[ 403.505741] softirqs last disabled at (50851): [<c001c268>] irq_exit+0x88/0xdc
[ 403.513026]
[ 403.513026] other info that might help us debug this:
[ 403.519593] Possible unsafe locking scenario:
[ 403.519593]
[ 403.525548] CPU0
[ 403.528020] ----
[ 403.530491] lock(&(&imxdma->lock)->rlock);
[ 403.534828] <Interrupt>
[ 403.537474] lock(&(&imxdma->lock)->rlock);
[ 403.541983]
[ 403.541983] *** DEADLOCK ***
[ 403.541983]
[ 403.547951] no locks held by swapper/0.
[ 403.551813]
[ 403.551813] stack backtrace:
[ 403.556222] CPU: 0 PID: 0 Comm: swapper Not tainted 3.10.0-20130823+ #904
[ 403.563039] Backtrace:
[ 403.565581] [<c000b98c>] (dump_backtrace+0x0/0x10c) from [<c000bb28>] (show_stack+0x18/0x1c)
[ 403.574054] r6:00000000 r5:c05c51d8 r4:c040bd58 r3:00200000
[ 403.579872] [<c000bb10>] (show_stack+0x0/0x1c) from [<c02f398c>] (dump_stack+0x20/0x28)
[ 403.587955] [<c02f396c>] (dump_stack+0x0/0x28) from [<c02f29c8>] (print_usage_bug.part.28+0x224/0x28c)
[ 403.597340] [<c02f27a4>] (print_usage_bug.part.28+0x0/0x28c) from [<c004b404>] (mark_lock+0x440/0x6b4)
[ 403.606682] r8:c004a41c r7:00000000 r6:c040bd58 r5:c040c040 r4:00000002
[ 403.613566] [<c004afc4>] (mark_lock+0x0/0x6b4) from [<c004d844>] (__lock_acquire+0x6cc/0x1a64)
[ 403.622244] [<c004d178>] (__lock_acquire+0x0/0x1a64) from [<c004f15c>] (lock_acquire+0x94/0xa8)
[ 403.631010] [<c004f0c8>] (lock_acquire+0x0/0xa8) from [<c02f74e4>] (_raw_spin_lock+0x54/0x8c)
[ 403.639614] [<c02f7490>] (_raw_spin_lock+0x0/0x8c) from [<c019d77c>] (imxdma_tasklet+0x20/0x134)
[ 403.648434] r6:c3847010 r5:c040e890 r4:c38470d4
[ 403.653194] [<c019d75c>] (imxdma_tasklet+0x0/0x134) from [<c001c70c>] (tasklet_action+0x8c/0xdc)
[ 403.662013] r8:c0599160 r7:00000000 r6:00000000 r5:c040e890 r4:c3847114 r3:c019d75c
[ 403.670042] [<c001c680>] (tasklet_action+0x0/0xdc) from [<c001bd4c>] (__do_softirq+0xe4/0x1f0)
[ 403.678687] r7:00000101 r6:c0402000 r5:c059919c r4:00000001
[ 403.684498] [<c001bc68>] (__do_softirq+0x0/0x1f0) from [<c001c268>] (irq_exit+0x88/0xdc)
[ 403.692652] [<c001c1e0>] (irq_exit+0x0/0xdc) from [<c0009cc8>] (handle_IRQ+0x6c/0x8c)
[ 403.700514] r4:00000030 r3:00000110
[ 403.704192] [<c0009c5c>] (handle_IRQ+0x0/0x8c) from [<c0008714>] (avic_handle_irq+0x3c/0x48)
[ 403.712664] r5:c0403f28 r4:c0593ebc
[ 403.716343] [<c00086d8>] (avic_handle_irq+0x0/0x48) from [<c0008f84>] (__irq_svc+0x44/0x74)
[ 403.724733] Exception stack(0xc0403f28 to 0xc0403f70)
[ 403.729841] 3f20: 00000001 00000004 00000000 20000013 c0402000 c04104a8
[ 403.738078] 3f40: 00000002 c0b69620 a0004000 41069264 a03fb5f4 c0403f7c c0403f40 c0403f70
[ 403.746301] 3f60: c004b92c c0009e74 20000013 ffffffff
[ 403.751383] r6:ffffffff r5:20000013 r4:c0009e74 r3:c004b92c
[ 403.757210] [<c0009e30>] (arch_cpu_idle+0x0/0x4c) from [<c0040b04>] (cpu_startup_entry+0x88/0xf4)
[ 403.766161] [<c0040a7c>] (cpu_startup_entry+0x0/0xf4) from [<c02f00d0>] (rest_init+0xb8/0xe0)
[ 403.774753] [<c02f0018>] (rest_init+0x0/0xe0) from [<c03e07dc>] (start_kernel+0x28c/0x2d4)
[ 403.783051] r6:c03fc484 r5:ffffffff r4:c040a0e0
[ 403.787797] [<c03e0550>] (start_kernel+0x0/0x2d4) from [<a0008040>] (0xa0008040)
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
When perparing cyclic_dma buffers by the sound layer, it will dump the
following lockdep trace. The leading snd_pcm_action_single get called
with read_lock_irq called. To fix this, we change the kcalloc call from
GFP_KERNEL to GFP_ATOMIC.
WARNING: at kernel/lockdep.c:2740 lockdep_trace_alloc+0xcc/0x114()
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
Modules linked in:
CPU: 0 PID: 832 Comm: aplay Not tainted 3.11.0-20130823+ #903
Backtrace:
[<c000b98c>] (dump_backtrace+0x0/0x10c) from [<c000bb28>] (show_stack+0x18/0x1c)
r6:c004c090 r5:00000009 r4:c2e0bd18 r3:00404000
[<c000bb10>] (show_stack+0x0/0x1c) from [<c02f397c>] (dump_stack+0x20/0x28)
[<c02f395c>] (dump_stack+0x0/0x28) from [<c001531c>] (warn_slowpath_common+0x54/0x70)
[<c00152c8>] (warn_slowpath_common+0x0/0x70) from [<c00153dc>] (warn_slowpath_fmt+0x38/0x40)
r8:00004000 r7:a3b90000 r6:000080d0 r5:60000093 r4:c2e0a000 r3:00000009
[<c00153a4>] (warn_slowpath_fmt+0x0/0x40) from [<c004c090>] (lockdep_trace_alloc+0xcc/0x114)
r3:c03955d8 r2:c03907db
[<c004bfc4>] (lockdep_trace_alloc+0x0/0x114) from [<c008f16c>] (__kmalloc+0x34/0x118)
r6:000080d0 r5:c3800120 r4:000080d0 r3:c040a0f8
[<c008f138>] (__kmalloc+0x0/0x118) from [<c019c95c>] (imxdma_prep_dma_cyclic+0x64/0x168)
r7:a3b90000 r6:00000004 r5:c39d8420 r4:c3847150
[<c019c8f8>] (imxdma_prep_dma_cyclic+0x0/0x168) from [<c024618c>] (snd_dmaengine_pcm_trigger+0xa8/0x160)
[<c02460e4>] (snd_dmaengine_pcm_trigger+0x0/0x160) from [<c0241fa8>] (soc_pcm_trigger+0x90/0xb4)
r8:c058c7b0 r7:c3b8140c r6:c39da560 r5:00000001 r4:c3b81000
[<c0241f18>] (soc_pcm_trigger+0x0/0xb4) from [<c022ece4>] (snd_pcm_do_start+0x2c/0x38)
r7:00000000 r6:00000003 r5:c058c7b0 r4:c3b81000
[<c022ecb8>] (snd_pcm_do_start+0x0/0x38) from [<c022e958>] (snd_pcm_action_single+0x40/0x6c)
[<c022e918>] (snd_pcm_action_single+0x0/0x6c) from [<c022ea64>] (snd_pcm_action_lock_irq+0x7c/0x9c)
r7:00000003 r6:c3b810f0 r5:c3b810f0 r4:c3b81000
[<c022e9e8>] (snd_pcm_action_lock_irq+0x0/0x9c) from [<c023009c>] (snd_pcm_common_ioctl1+0x7f8/0xfd0)
r8:c3b7f888 r7:005407b8 r6:c2c991c0 r5:c3b81000 r4:c3b81000 r3:00004142
[<c022f8a4>] (snd_pcm_common_ioctl1+0x0/0xfd0) from [<c023117c>] (snd_pcm_playback_ioctl1+0x464/0x488)
[<c0230d18>] (snd_pcm_playback_ioctl1+0x0/0x488) from [<c02311d4>] (snd_pcm_playback_ioctl+0x34/0x40)
r8:c3b7f888 r7:00004142 r6:00000004 r5:c2c991c0 r4:005407b8
[<c02311a0>] (snd_pcm_playback_ioctl+0x0/0x40) from [<c00a14a4>] (vfs_ioctl+0x30/0x44)
[<c00a1474>] (vfs_ioctl+0x0/0x44) from [<c00a1fe8>] (do_vfs_ioctl+0x55c/0x5c0)
[<c00a1a8c>] (do_vfs_ioctl+0x0/0x5c0) from [<c00a208c>] (SyS_ioctl+0x40/0x68)
[<c00a204c>] (SyS_ioctl+0x0/0x68) from [<c0009380>] (ret_fast_syscall+0x0/0x44)
r8:c0009544 r7:00000036 r6:bedeaa58 r5:00000000 r4:000000c0
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Commit d0380e6c3c0f6edb986d8798a23acfaf33d5df23 (early_printk:
consolidate random copies of identical code) added in 3.10 introduced
a check for con->index == -1 in early_console_register().
Initialize index to -1 for the xenboot console so earlyprintk=xen
works again.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Also clean up the last item of the pci id list to be "cleaner".
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The `insn_bits` handler `ni_65xx_dio_insn_bits()` has a `for` loop that
currently writes (optionally) and reads back up to 5 "ports" consisting
of 8 channels each. It reads up to 32 1-bit channels but can only read
and write a whole port at once - it needs to handle up to 5 ports as the
first channel it reads might not be aligned on a port boundary. It
breaks out of the loop early if the next port it handles is beyond the
final port on the card. It also breaks out early on the 5th port in the
loop if the first channel was aligned. Unfortunately, it doesn't check
that the current port it is dealing with belongs to the comedi subdevice
the `insn_bits` handler is acting on. That's a bug.
Redo the `for` loop to terminate after the final port belonging to the
subdevice, changing the loop variable in the process to simplify things
a bit. The `for` loop could now try and handle more than 5 ports if the
subdevice has more than 40 channels, but the test `if (bitshift >= 32)`
ensures it will break out early after 4 or 5 ports (depending on whether
the first channel is aligned on a port boundary). (`bitshift` will be
between -7 and 7 inclusive on the first iteration, increasing by 8 for
each subsequent operation.)
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: <stable@vger.kernel.org> # 3.10.y 3.11.y 3.12.y
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch bumps the default number of tags allocated per session by
iscsi-target via transport_alloc_session_tags() -> percpu_ida_init()
by another (tag_num / 2).
This is done to take into account the tags waiting to be acknowledged
and released in iscsit_ack_from_expstatsn(), but who's number are not
directly limited by the CmdSN Window queue_depth being enforced by
the target.
Using a larger value here is also useful to prevent percpu_ida_alloc()
from having to steal tags from other CPUs when no tags are available
on the local CPU, while waiting for unacknowledged tags to be released.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch converts iscsit_ack_from_expstatsn() to populate a local
ack_list of commands, and call iscsit_free_cmd() directly from RX
thread context, instead of using iscsit_add_cmd_to_immediate_queue()
to queue the acknowledged commands to be released from TX thread
context.
It is helpful to release the acknowledge commands as quickly as
possible, along with the associated percpu_ida tags, in order to
prevent percpu_ida_alloc() from having to steal tags from other
CPUs while waiting for iscsit_free_cmd() to happen from TX thread
context.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch changes transport_generic_free_cmd() to only wait_for_tasks
when shutdown=true is passed to iscsit_free_cmd().
With the advent of >= v3.10 iscsi-target code using se_cmd->cmd_kref,
the extra wait_for_tasks with shutdown=false is unnecessary, and may
end up causing an extra context switch when releasing WRITEs.
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch addresses a bug for backends such as IBLOCK that perform
asynchronous completion via transport_complete_cmd(), that will call
target_complete_failure_work() -> transport_generic_request_failure(),
upon exception status and invoke cmd->transport_complete_callback()
-> compare_and_write_callback() incorrectly during the failure case.
It adds a check for a non zero se_cmd->scsi_status within the first
invocation of compare_and_write_callback(), and will jump to out plus
up se_device->caw_sem before exiting the callback.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch addresses a bug when compare_and_write_callback() invoked from
target_complete_ok_work() hits an failure from __target_execute_cmd() ->
cmd->execute_cmd(), that ends up calling transport_generic_request_failure()
-> compare_and_write_post(), thus causing SCF_COMPARE_AND_WRITE_POST to
incorrectly be set.
The result of this bug is that target_complete_ok_work() no longer hits
the if (!rc && !(cmd->se_cmd_flags & SCF_COMPARE_AND_WRITE_POST) check
that forces an immediate return, and instead double completes the se_cmd
in question, triggering an OOPs in the process.
This patch changes compare_and_write_post() to only set this bit when a
failure has not already occured to ensure the immediate return from within
target_complete_ok_work(), and thus allow transport_generic_request_failure()
to handle the sending of the CHECK_CONDITION exception status.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch resets se_cmd->data_length for COMPARE_AND_WRITE emulation
within sbc_compare_and_write() to NoLB * block_size in order to address
a bug with FILEIO backends where a I/O failure will occur when data_length
does not match the I/O size being actually dispatched for the individual
per block READs + WRITEs.
This is done late enough in sbc_compare_and_write() after the memory
allocations have occured in transport_generic_new_cmd() to not cause
any unwanted side-effects.
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The SRP specification requires:
"Response data shall be provided in any SRP_RSP response that is sent in
response to an SRP_TSK_MGMT request (see 6.7). The information in the
RSP_CODE field (see table 24) shall indicate the completion status of
the task management function."
So fix this to avoid the SRP initiator interprets task management functions
that succeeded as failed.
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Cc: stable@vger.kernel.org # 3.3+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We have a fairly large batch of fixes this time around, mostly just
due to various platforms all having a fix or two more than usual.
Worth pointing out are:
- A fix for EDMA on Davinci/OMAP where channel allocation broke with
the DT conversion. Due to some miscommunication we didn't
understand the impact of the breakage, so we were pushing back on
it for 3.12, but it sounds like it's actually breaking quite a few
people out there.
- A bunch of fixes for Marvell platforms, some straggling fixes for
merge window fallout and some fixes for a couple of the platforms
(Netgear RN102 in particular).
- A fix for a race between multi-cluster power management and cpu
hotplug on Versatile Express.
And a bunch of other smaller fixes that all add up.
We'll be switching over into stricter regressions-only mode from here
on out"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: multi_v7_defconfig: add SDHCI for i.MX
bus: mvebu-mbus: Fix optional pcie-mem/io-aperture properties
ARM: mvebu: add missing DT Mbus ranges and relocate PCIe DT nodes for RN102
ARM: at91: sam9g45: shutdown ddr1 too when rebooting
MAINTAINERS: ARM: SIRF: use kernel.org mail box
MAINTAINERS: ARM: SIRF: add missed drivers into maintain list
ARM: edma: Fix clearing of unused list for DT DMA resources
ARM: vexpress: tc2: fix hotplug/idle/kexec race on cluster power down
ARM: dts: sirf: fix interrupt and dma prop of VIP for prima2 and atlas6
ARM: dts: sirf: fix the ranges of peri-iobrg of prima2
ARM: dts: makefile: build atlas6-evb.dtb for ARCH_ATLAS6
ARM: dts: sirf: fix fifosize, clks, dma channels for UART
ARM: mvebu: Add DT entry for ReadyNAS 102 to use gpio-poweroff driver
ARM: mvebu: fix ReadyNAS 102 Power button GPIO to make it active high
ARM: mach-integrator: Add stub for pci_v3_early_init() for !CONFIG_PCI
ARM: shmobile: Remove #gpio-ranges-cells DT property
gpio: rcar: Remove #gpio-range-cells DT property usage
ARM: shmobile: armadillo: fixup ether pinctrl naming
ARM: shmobile: Lager: add Micrel KSZ8041 PHY fixup
ARM: shmobile: update SDHI DT compatibility string to the <unit>-<soc> format
...
|
|
From Jason Cooper:
mvebu fixes for v3.12 (round 2)
- mvebu
- fix ReadyNAS 102 power button (needs to be active high)
- fix ReadyNAS 102 automated rebooting (prevent hang) by add gpio-poweroff
node
- fix booting ReadyNAS 102 by adding MBus ranges and PCIe DT nodes
- mvebu-mbus: prevent PCIe driver from continuing with corrupted resource
* tag 'fixes-3.12-2' of git://git.infradead.org/linux-mvebu:
bus: mvebu-mbus: Fix optional pcie-mem/io-aperture properties
ARM: mvebu: add missing DT Mbus ranges and relocate PCIe DT nodes for RN102
ARM: mvebu: Add DT entry for ReadyNAS 102 to use gpio-poweroff driver
ARM: mvebu: fix ReadyNAS 102 Power button GPIO to make it active high
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Various build warning fixes.
- Correct the S5P pin count.
- Handle BIAS_DEFAULT properly in the Palmas driver.
* tag 'pinctrl-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: palmas: do not abort pin configuration for BIAS_DEFAULT
pinctrl: Correct number of pins for s5pv210
pinctrl: remove an unnecessary cast
pinctrl: fix pinconf_dbg_config_write return type
pinctrl: tegra114: Remove MODULE_ALIAS
|
|
* pm-fixes:
intel_pstate: fix no_turbo
cpufreq: cpufreq-cpu0: NULL is a valid regulator, part 2
cpufreq: SPEAr: Fix incorrect variable type
PM / hibernate: Fix user space driven resume regression
|
|
This patch changes transport_alloc_session_tags() to fall back to
use vzalloc when kzalloc fails for big tag_num that end up generating
larger order allocations.
Also use is_vmalloc_addr() in transport_alloc_session_tags() failure
path, and normal transport_free_session() path to determine when
vfree() needs to be called instead of kfree().
v2 changes:
- Use __GFP_NOWARN | __GFP_REPEAT for sess_cmd_map kzalloc (mst)
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Asias He <asias@redhat.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Fix GFP_KERNEL -> GFP_ATOMIC usage of percpu_ida_alloc() within
vhost_scsi_get_tag(), as this code is expected to be called directly
from interrupt context.
v2 changes:
- Handle possible tag < 0 failure with GFP_ATOMIC
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Asias He <asias@redhat.com>
Cc: Kent Overstreet <kmo@daterainc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a bug where ib_destroy_cm_id() was incorrectly being called
after srpt_destroy_ch_ib() had destroyed the active QP.
This would result in the following failed SRP_LOGIN_REQ messages:
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff1762bd, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 1 (guid=0xfe80000000000000:0x2c903009f8f41)
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff1758f9, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 2 (guid=0xfe80000000000000:0x2c903009f8f42)
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff175941, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 2 (guid=0xfe80000000000000:0x2c90300a3cfb2)
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff176299, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 1 (guid=0xfe80000000000000:0x2c90300a3cfb1)
mlx4_core 0000:84:00.0: command 0x19 failed: fw status = 0x9
rejected SRP_LOGIN_REQ because creating a new RDMA channel failed.
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff176299, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 1 (guid=0xfe80000000000000:0x2c90300a3cfb1)
mlx4_core 0000:84:00.0: command 0x19 failed: fw status = 0x9
rejected SRP_LOGIN_REQ because creating a new RDMA channel failed.
Received SRP_LOGIN_REQ with i_port_id 0x0:0x2590ffff176299, t_port_id 0x2c903009f8f40:0x2c903009f8f40 and it_iu_len 260 on port 1 (guid=0xfe80000000000000:0x2c90300a3cfb1)
Reported-by: Navin Ahuja <navin.ahuja@saratoga-speed.com>
Cc: stable@vger.kernel.org # 3.3+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes up an incorrect assignment for xop->dbl within
target_xcopy_parse_segdesc_02() code, as reported by Coverity here:
http://marc.info/?l=linux-kernel&m=137936416618490&w=2
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.12-rc4
Here are some more fixes to musb's OTG support and a regression
caused on latest merge window; pxa25x_udc and gpio-vbus learned
to cope with deferred probe; s3c-hsotg got a fix for non-periodic
endpoints write size and f_fs got an error handling fix for cases
where ffs_do_descs() fail.
Signed-of-by: Felipe Balbi <balbi@ti.com>
|
|
Commit caf5c03f (ACPI: Move acpi_bus_get_device() from bus.c to
scan.c) caused acpi_bus_get_device() to be exported using
EXPORT_SYMBOL_GPL(), but that broke some binary drivers in
existence, so revert that change.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When sysfs for no_turbo is set, then also some p states in turbo regions
are observed. This patch will set IDA Engage bit when no_turbo is set to
explicitly disengage turbo.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull networking changes from David Miller:
1) Multiply in netfilter IPVS can overflow when calculating destination
weight. From Simon Kirby.
2) Use after free fixes in IPVS from Julian Anastasov.
3) SFC driver bug fixes from Daniel Pieczko.
4) Memory leak in pcan_usb_core failure paths, from Alexey Khoroshilov.
5) Locking and encapsulation fixes to serial line CAN driver, from
Andrew Naujoks.
6) Duplex and VF handling fixes to bnx2x driver from Yaniv Rosner,
Eilon Greenstein, and Ariel Elior.
7) In lapb, if no other packets are outstanding, T1 timeouts actually
stall things and no packet gets sent. Fix from Josselin Costanzi.
8) ICMP redirects should not make it to the socket error queues, from
Duan Jiong.
9) Fix bugs in skge DMA mapping error handling, from Nikulas Patocka.
10) Fix setting of VLAN priority field on via-rhine driver, from Roget
Luethi.
11) Fix TX stalls and VLAN promisc programming in be2net driver from
Ajit Khaparde.
12) Packet padding doesn't get handled correctly in new usbnet SG
support code, from Ming Lei.
13) Fix races in netdevice teardown wrt. network namespace closing.
From Eric W. Biederman.
14) Fix potential missed initialization of net_secret if not TCP
connections are openned. From Eric Dumazet.
15) Cinterion PLXX product ID in qmi_wwan driver is wrong, from
Aleksander Morgado.
16) skb_cow_head() can change skb->data and thus packet header pointers,
don't use stale ip_hdr reference in ip_tunnel code.
17) Backend state transition handling fixes in xen-netback, from Paul
Durrant.
18) Packet offset for AH protocol is handled wrong in flow dissector,
from Eric Dumazet.
19) Taking down an fq packet scheduler instance can leave stale packets
in the queues, fix from Eric Dumazet.
20) Fix performance regressions introduced by TCP Small Queues. From
Eric Dumazet.
21) IPV6 GRE tunneling code calculates max_headroom incorrectly, from
Hannes Frederic Sowa.
22) Multicast timer handlers in ipv4 and ipv6 can be the last and final
reference to the ipv4/ipv6 specific network device state, so use the
reference put that will check and release the object if the
reference hits zero. From Salam Noureddine.
23) Fix memory corruption in ip_tunnel driver, and use skb_push()
instead of __skb_push() so that similar bugs are less hard to find.
From Steffen Klassert.
24) Add forgotten hookup of rtnl_ops in SIT and ip6tnl drivers, from
Nicolas Dichtel.
25) fq scheduler doesn't accurately rate limit in certain circumstances,
from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (103 commits)
pkt_sched: fq: rate limiting improvements
ip6tnl: allow to use rtnl ops on fb tunnel
sit: allow to use rtnl ops on fb tunnel
ip_tunnel: Remove double unregister of the fallback device
ip_tunnel_core: Change __skb_push back to skb_push
ip_tunnel: Add fallback tunnels to the hash lists
ip_tunnel: Fix a memory corruption in ip_tunnel_xmit
qlcnic: Fix SR-IOV configuration
ll_temac: Reset dma descriptors indexes on ndo_open
skbuff: size of hole is wrong in a comment
ipv6 mcast: use in6_dev_put in timer handlers instead of __in6_dev_put
ipv4 igmp: use in_dev_put in timer handlers instead of __in_dev_put
ethernet: moxa: fix incorrect placement of __initdata tag
ipv6: gre: correct calculation of max_headroom
powerpc/83xx: gianfar_ptp: select 1588 clock source through dts file
Revert "powerpc/83xx: gianfar_ptp: select 1588 clock source through dts file"
bonding: Fix broken promiscuity reference counting issue
tcp: TSQ can use a dynamic limit
dm9601: fix IFF_ALLMULTI handling
pkt_sched: fq: qdisc dismantle fixes
...
|
|
If the property was not specified then the returned resource had a
resource_size(..) == 1, rather than 0. The PCI-E driver checks for 0 so it
blindly continues on with a corrupted resource.
The regression was introduced into v3.12 by:
11be654 PCI: mvebu: Adapt to the new device tree layout
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
o Interface needs to be brought down and up while configuring SR-IOV.
Protect interface up/down using rtnl_lock()/rtnl_unlock()
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dma descriptors indexes are only initialized on the probe function.
If a packet is on the buffer when temac_stop is called, the dma
descriptors indexes can be left on a incorrect state where no other
package can be sent.
So an interface could be left in an usable state after ifdow/ifup.
This patch makes sure that the descriptors indexes are in a proper
status when the device is open.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Value of can_write variable in s3c_hsotg_write_fifo function should be limited
to 512 only for non-periodic endpoints. There was some discrepancy between
comment and code, because comment suggests correct behavior, but in the code
limit was applied to periodic endpoints too. So there is additional check
causing the limitation concerns only non-periodic endpoints.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
