summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)Author
2008-12-03hysdn: fix writing outside the field on 64 bitsPascal Terjan
ifa_local is assumed to be unsigned long which lead to writing the address at dev->dev_addr-2 instead of +2 noticed thanks to gcc: drivers/isdn/hysdn/hysdn_net.c: In function `net_open': drivers/isdn/hysdn/hysdn_net.c:91: warning: array subscript is below array bounds Signed-off-by: Pascal Terjan <pterjan@mandriva.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-03b1isa: fix b1isa_exit() to really remove registered capi controllersWilfried Klaebe
On "/etc/init.d/capiutils stop", this oops happened. The oops happens on reading /proc/capi/controllers because capi_ctrl->procinfo is called for the wrongly not unregistered controller, which points to b1isa_procinfo(), which was removed on module unload. b1isa_exit() did not call b1isa_remove() for its controllers because io[0] == 0 on module unload despite having been 0x340 on module load. Besides, just removing the controllers that where added on module load time and not those that were added later via b1isa_add_card() is wrong too - the place where all added cards are found is isa_dev[]. relevant dmesg lines: [ 0.000000] Linux version 2.6.27.4 (w@shubashi) (gcc version 4.3.2 (Debian 4.3.2-1) ) #3 Thu Oct 30 16:49:03 CET 2008 [ 67.403555] CAPI Subsystem Rev 1.1.2.8 [ 68.529154] capifs: Rev 1.1.2.3 [ 68.563292] capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs) [ 77.026936] b1: revision 1.1.2.2 [ 77.049992] b1isa: revision 1.1.2.3 [ 77.722655] kcapi: Controller [001]: b1isa-340 attached [ 77.722671] b1isa: AVM B1 ISA at i/o 0x340, irq 5, revision 255 [ 81.272669] b1isa-340: card 1 "B1" ready. [ 81.272683] b1isa-340: card 1 Protocol: DSS1 [ 81.272689] b1isa-340: card 1 Linetype: point to multipoint [ 81.272695] b1isa-340: B1-card (3.11-03) now active [ 81.272702] kcapi: card [001] "b1isa-340" ready. [ 153.721281] kcapi: card [001] down. [ 154.151889] BUG: unable to handle kernel paging request at e87af000 [ 154.152081] IP: [<e87af000>] [ 154.153292] *pde = 2655b067 *pte = 00000000 [ 154.153307] Oops: 0000 [#1] [ 154.153360] Modules linked in: rfcomm l2cap ppdev lp ipt_MASQUERADE tun capi capifs kernelcapi ac battery nfsd exportfs nfs lockd nfs_acl sunrpc sit tunnel4 bridge stp llc ipt_REJECT ipt_LOG xt_tcpudp xt_state iptable_filter iptable_mangle iptable_nat nf_nat nf_conntrack_ipv4 nf_conntrack ip_tables x_tables nls_utf8 isofs nls_base zlib_inflate loop ipv6 netconsole snd_via82xx dvb_usb_dib0700 gameport dib7000p dib7000m dvb_usb snd_ac97_codec ac97_bus dvb_core mt2266 snd_pcm tuner_xc2028 dib3000mc dibx000_common mt2060 dib0070 snd_page_alloc snd_mpu401_uart snd_seq_midi snd_seq_midi_event btusb snd_rawmidi bluetooth snd_seq snd_timer snd_seq_device snd via686a i2c_viapro soundcore i2c_core parport_pc parport button dm_mirror dm_log dm_snapshot floppy sg ohci1394 uhci_hcd ehci_hcd 8139too mii ieee1394 usbcore sr_mod cdrom sd_mod thermal processor fan [last unloaded: b1] [ 154.153360] [ 154.153360] Pid: 4132, comm: capiinit Not tainted (2.6.27.4 #3) [ 154.153360] EIP: 0060:[<e87af000>] EFLAGS: 00010286 CPU: 0 [ 154.153360] EIP is at 0xe87af000 [ 154.153360] EAX: e6b9ccc8 EBX: e6b9ccc8 ECX: e87a0c67 EDX: e87af000 [ 154.153360] ESI: e142bbc0 EDI: e87a56e0 EBP: e0505f0c ESP: e0505ee4 [ 154.153360] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068 [ 154.153360] Process capiinit (pid: 4132, ti=e0504000 task=d1196cf0 task.ti=e0504000) [ 154.153360] Stack: e879f650 00000246 e0505ef4 c01472eb e0505f0c 00000246 e7001780 fffffff4 [ 154.153360] fffffff4 e142bbc0 e0505f48 c01a56c6 00000400 b805e000 d102dc80 e142bbe0 [ 154.153360] 00000000 e87a56e0 00000246 e12617ac 00000000 00000000 e1261760 fffffffb [ 154.153360] Call Trace: [ 154.153360] [<e879f650>] ? controller_show+0x20/0x90 [kernelcapi] [ 154.153360] [<c01472eb>] ? trace_hardirqs_on+0xb/0x10 [ 154.153360] [<c01a56c6>] ? seq_read+0x126/0x2f0 [ 154.153360] [<c01a55a0>] ? seq_read+0x0/0x2f0 [ 154.153360] [<c01c033c>] ? proc_reg_read+0x5c/0x90 [ 154.153360] [<c0189919>] ? vfs_read+0x99/0x140 [ 154.153360] [<c01c02e0>] ? proc_reg_read+0x0/0x90 [ 154.153360] [<c0189a7d>] ? sys_read+0x3d/0x70 [ 154.153360] [<c0103c3d>] ? sysenter_do_call+0x12/0x35 [ 154.153360] ======================= [ 154.153360] Code: Bad EIP value. [ 154.153360] EIP: [<e87af000>] 0xe87af000 SS:ESP 0068:e0505ee4 [ 154.153360] ---[ end trace 23750b6c2862de94 ]--- Signed-off-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Karsten Keil <kkeil@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-03bnx2: Add workaround to handle missed MSI.Michael Chan
The bnx2 chips do not support per MSI vector masking. On 5706/5708, new MSI address/data are stored only when the MSI enable bit is toggled. As a result, SMP affinity no longer works in the latest kernel. A more serious problem is that the driver will no longer receive interrupts when the MSI receiving CPU goes offline. The workaround in this patch only addresses the problem of CPU going offline. When that happens, the driver's timer function will detect that it is making no forward progress on pending interrupt events and will recover from it. Eric Dumazet reported the problem. We also found that if an interrupt is internally asserted while MSI and INTA are disabled, the chip will end up in the same state after MSI is re-enabled. The same workaround is needed for this problem. Signed-off-by: Michael Chan <mchan@broadcom.com> Tested-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdogLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: [WATCHDOG] hpwdt: Fix kdump when using hpwdt [WATCHDOG] hpwdt: set the mapped BIOS address space as executable [WATCHDOG] iTCO_wdt: add PCI ID's for ICH9 & ICH10 chipsets [WATCHDOG] iTCO_wdt : correct status clearing [WATCHDOG] iTCO_wdt : problem with rebooting on new ICH9 based motherboards [WATCHDOG] fix mtx1_wdt compilation failure
2008-12-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6: sparc64: Fix offset calculation in compute_size() rtc: rtc-starfire fixes
2008-12-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits) MAINTAINERS: add netdev to ATM ATM: horizon, fix hrz_probe fail path pppol2tp: Add missing sock_put() in pppol2tp_release() net: Fix soft lockups/OOM issues w/ unix garbage collector macvlan: don't broadcast PAUSE frames to macvlan devices Phonet: fix oops in phonet_address_del() on non-Phonet device netfilter: ctnetlink: fix GFP_KERNEL allocation under spinlock sungem: Fix PCS_MIICTRL register write in gem_init_phy(). net: make skb_truesize_bug() call WARN() net: hp-plus uses eip_poll net/wireless/reg.c: fix bad WARN_ON in if statement ath5k: disable beacon filter when station is not associated ath5k: fix Security issue in DebugFS part of ath5k ath9k: correct expected max RX buffer size ath9k: Fix SW-IOMMU bounce buffer starvation mac80211 : Fix setting ad-hoc mode and non-ibss channel iwlagn: fix DMA sync phylib: Add Vitesse VSC8221 SGMII PHY rose: zero length frame filtering in af_rose.c bridge: netfilter: fix update_pmtu crash with GRE ...
2008-12-02Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: m68k: Update defconfigs for 2.6.28-rc7 macfb: Do not overflow fb_fix_screeninfo.id
2008-12-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: alim15x3: fix sparse warning ide: remove dead code from drive_is_ready() ide: fix build for DEBUG_PM ide: respect current DMA setting during resume ide: add SAMSUNG SP0822N with firmware WA100-10 to ivb_list[] amd74xx: workaround unreliable AltStatus register for nVidia controllers ide: fix the ide_release_lock imbalance
2008-12-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: [SCSI] stex: switch to block timeout [SCSI] make scsi_eh_try_stu use block timeout [SCSI] megaraid_sas: switch to block timeout [SCSI] ibmvscsi: switch to block timeout [SCSI] aacraid: switch to block timeout [SCSI] zfcp: prevent double decrement on host_busy while being busy [SCSI] zfcp: fix deadlock between wq triggered port scan and ERP [SCSI] zfcp: eliminate race between validation and locking [SCSI] zfcp: verify for correct rport state before scanning for SCSI devs [SCSI] zfcp: returning an ERR_PTR where a NULL value is expected [SCSI] zfcp: Fix opening of wka ports [SCSI] zfcp: fix remote port status check [SCSI] fc_transport: fix old bug on bitflag definitions [SCSI] Fix hang in starved list processing
2008-12-02sgi-gru: call fs_initcall() if statically linkedDean Nelson
If xpc.ko and gru.ko are both statically linked into the kernel, then xpc_init() can get called before gru_init() and make a call to one of the gru's exported functions before the gru has initialized itself. The end result is a NULL dereference. Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-02alim15x3: fix sparse warningHannes Eder
Fix this sparse warning: drivers/ide/alim15x3.c:594:2: warning: returning void-valued expression Signed-off-by: Hannes Eder <hannes@hanneseder.net> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-12-02ide: remove dead code from drive_is_ready()Bartlomiej Zolnierkiewicz
We guarantee 400ns delay at the time of issuing the command. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-12-02ide: fix build for DEBUG_PMBartlomiej Zolnierkiewicz
Also while at it: * Drop unused arguments from ide_complete_power_step(). * Move DEBUG_PM printk() from ide_end_drive_cmd() to ide_complete_power_step(). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-12-02ide: respect current DMA setting during resumeBartlomiej Zolnierkiewicz
Respect current DMA setting during resume, otherwise PIO timings may get destroyed if host uses shared PIO/MWDMA timings. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-12-02ide: add SAMSUNG SP0822N with firmware WA100-10 to ivb_list[]Bartlomiej Zolnierkiewicz
Should fix kernel.org bug #10225: http://bugzilla.kernel.org/show_bug.cgi?id=10225 Reported-by: Matthias B. <haferfrost@web.de> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Acked-by: Sergei Shtyltov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-12-02amd74xx: workaround unreliable AltStatus register for nVidia controllersBartlomiej Zolnierkiewicz
It seems that on some nVidia controllers using AltStatus register can be unreliable so default to Status register if the PCI device is in Compatibility Mode. In order to achieve this: * Add ide_pci_is_in_compatibility_mode() inline helper to <linux/ide.h>. * Add IDE_HFLAG_BROKEN_ALTSTATUS host flag and set it in amd74xx host driver for nVidia controllers in Compatibility Mode. * Teach actual_try_to_identify() and drive_is_ready() about the new flag. This fixes the regression caused by removal of CONFIG_IDEPCI_SHARE_IRQ config option in 2.6.25 and using AltStatus register unconditionally when available (kernel.org bugs #11659 and #10216). [ Moreover for CONFIG_IDEPCI_SHARE_IRQ=y (which is what most people and distributions use) it never worked correctly. ] Thanks to Remy LABENE and Lars Winterfeld for help with debugging the problem. More info at: http://bugzilla.kernel.org/show_bug.cgi?id=11659 http://bugzilla.kernel.org/show_bug.cgi?id=10216 Reported-by: Remy LABENE <remy.labene@free.fr> Tested-by: Remy LABENE <remy.labene@free.fr> Tested-by: Lars Winterfeld <lars.winterfeld@tu-ilmenau.de> Acked-by: Borislav Petkov <petkovbb@gmail.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-12-02ide: fix the ide_release_lock imbalanceMichael Schmitz
ide_release_lock() spits out lots of: ide_release_lock: bug warnings on Atari Falcon. Fix the ide_release_lock imbalance. Signed-off-by: Michael Schmitz <schmitz@biophys.uni-duesseldorf.de> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
2008-12-02macfb: Do not overflow fb_fix_screeninfo.idFinn Thain
Don't overflow the 16-character fb_fix_screeninfo id string (fixes some console erasing and blanking artifacts). Have the ID default to "Unknown" on machines with no built-in video and no nubus devices. Check for fb_alloc_cmap failure. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2008-12-01Merge branch 'for_linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6 * 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (25 commits) em28xx: remove backward compat macro added on a previous fix V4L/DVB (9748): em28xx: fix compile warning V4L/DVB (9743): em28xx: fix oops audio V4L/DVB (9742): em28xx-alsa: implement another locking schema V4L/DVB (9732): sms1xxx: use new firmware for Hauppauge WinTV MiniStick V4L/DVB (9691): gspca: Move the video device to a separate area. V4L/DVB (9690): gspca: Lock the subdrivers via module_get/put. V4L/DVB (9689): gspca: Memory leak when disconnect while streaming. V4L/DVB (9668): em28xx: fix a race condition with hald V4L/DVB (9664): af9015: don't reconnect device in USB-bus V4L/DVB (9647): em28xx: void having two concurrent control URB's V4L/DVB (9646): em28xx: avoid allocating/dealocating memory on every control urb V4L/DVB (9645): em28xx: Avoid memory leaks if registration fails V4L/DVB (9639): Make dib0700 remote control support work with firmware v1.20 V4L/DVB (9635): v4l: s2255drv fix firmware test on big-endian V4L/DVB (9634): Make sure the i2c gate is open before powering down tuner V4L/DVB (9632): make em28xx aux audio input work V4L/DVB (9631): Make s2api work for ATSC support V4L/DVB (9627): em28xx: Avoid i2c register error for boards without eeprom V4L/DVB (9608): Fix section mismatch warning for dm1105 during make ...
2008-12-01drivers/gpu/drm/i915/i915_irq.c: fix warningAndrew Morton
drivers/gpu/drm/i915/i915_irq.c: In function 'i915_disable_pipestat': drivers/gpu/drm/i915/i915_irq.c:101: warning: control may reach end of non-void function 'i915_pipestat' being inlined Cc: Dave Airlie <airlied@linux.ie> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-01i82875p_edac: fix module removeJarkko Lavinen
Fix module removal bugs of i82875p_edac. Also i82975x_edac code seems to have the same module removal bugs as in i82875p_edac. The problems were: 1. In module removal i82875p_remove_one() is never called. Variable i82875p_registered is newer changed from 1, which guarantees i82875p_remove_one() is not called (and even if it were called, it would be called in wrong order). As a result, the edac_mc workque is not stopped and keeps probing. If kernel debugging options are not enabled, user may not notice anything going wrong. if debugging options are enabled and I do "rmmod i82875p_edac", I get: edac debug: edac_pci_workq_function() checking BUG: unable to handle kernel paging request at f882d16f ... call trace: [<f8834df3>] ? edac_mc_workq_function+0x55/0x7e [edac_core] [<c0233974>] ? run_workqueue+0xd7/0x1a5 [<c023392f>] ? run_workqueue+0x92/0x1a5 [<f8834d9e>] ? edac_mc_workq_function+0x0/0x7e [edac_core] [<c0233af9>] ? worker_thread+0xb7/0xc3 [<c0236a7b>] ? autoremove_wake_function+0x0/0x33 [<c0233a42>] ? worker_thread+0x0/0xc3 [<c0236809>] ? kthread+0x3b/0x61 [<c02367ce>] ? kthread+0x0/0x61 [<c0204587>] ? kernel_thread_helper+0x7/0x10 Fix for this is to get rid of needles variable i82875p_registered altogether and run i82875p_remove_one() *before* pci_unregister_driver(). 2. edac_mc_del_mc() uses mci after freeing mci edac_mc_del_mc() calls calls edac_remove_sysfs_mci_device(). The kobject refcount of mci drops to 0 and mci is freed. After this mci is accessed via debug print and i82875p_remove_one() still uses mci->pvt and tries to free mci again with edac_mc_free(). The fix for this is add kobject_get(&mci->edac_mci_kobj) after edac_mc_alloc(). Then the mci is still available after returning from edac_mc_del_mc() with refcount 1, and mci->pvt is still available. When i82875p_remove_one() finally calls edac_mc_free(), this will cause kobject_put() and mci is released properly. Signed-off-by: Jarkko Lavinen <jlavi@iki.fi> Cc: Doug Thompson <norsk5@yahoo.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-01i82875p_edac: fix overflow device resource setupJarkko Lavinen
When I do "modprobe i82875p_edac" on my Asus P4C800 MB on kernels 2.6.26 or later, the module load fails due to BAR 0 collision. On 2.6.25 the module loads just fine. The overflow device on the MB seems to be hidden and its resources are not allocated at normal PCI bus init. Log shows the missing resource problem: EDAC DEBUG: i82875p_probe1() PCI: 0000:00:06.0 reg 10 32bit mmio: [fecf0000, fecf0fff] pci 0000:00:06.0: device not available because of BAR 0 [0xfecf0000-0xfecf0fff] collisions EDAC i82875p: i82875p_setup_overfl_dev(): Failed to enable overflow device The patch below fixes this by calling pci_bus_assign_resources() after the overflow device is revealed and added to the bus. With this patch I am again able to load and use the module. Signed-off-by: Jarkko Lavinen <jlavi@iki.fi> Cc: Doug Thompson <norsk5@yahoo.com> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-01fbdev: fix FB console blankingDmitry Baryshkov
The commit aef7db4bd5a3b6068dfa05919a3d685199eed116 fixed the problem with recursive locking in fb blanking code if blank is caused by user setting the /sys/class/graphics/fb*/blank. However this broke the fbcon timeout blanking. If you use a driver that defines ->fb_blank operation and at the same time that driver relies on other driver (e.g. backlight or lcd class) to blank the screen, when the fbcon times out and tries to blank the fb, it will call only fb driver blanker and won't notify the other driver. Thus FB output is disabled, but the screen isn't blanked. Restore fbcon blanking and at the same time apply the proper fix for the above problem: if fbcon_blank is called with FBINFO_FLAG_USEREVENT, we are already called through notification from fb_blank, thus we don't have to blank the fb again. Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-01radeonfb: fix problem with color expansion & alignmentBenjamin Herrenschmidt
The engine on some radeon variants locks up if color expansion is called for non aligned source data. This patch enables a feature of the core fbdev to request aligned input pixmaps and uses the HW clipping engine to clip the output to the requested size Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11875 Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by: James Cloos <cloos@jhcloos.com> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: "David S. Miller" <davem@davemloft.net> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-01spi: fix spi_s3c24xx_gpio num_chipselectBen Dooks
The spi master driver must have num_chipselect set to allow the bus to initialise. Pass this through the platform data. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-01spi: fix spi_s3c24xx_gpio device handle lookupBen Dooks
The spidev_to_sg() call in spi_s3c24xx_gpio.c was using the wrong method to convert the spi device into the private data for the driver. Fix this by using spi_master_get_devdata. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-01spi: au1550_spi full duplex dma fixJan Nikitenko
Fix unsafe order in dma mapping operation: always flush data from the cache *BEFORE* invalidating it, to allow full duplex transfers where the same buffer may be used for both writes and reads. Tested with mmc-spi. Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-01spi: fix spi_imx probe oopsingJulien Boibessot
Corrects spi_imx driver oops during initialization/probing: can't use drv_data before it's allocated. Signed-off-by: Julien Boibessot <julien.boibessot@armadeus.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-01spi: mpc52xx_psc_spi chipselect bugfixStefano Babic
According to the manual the "tdfOnExit" flag must be set on the last byte we want to send. The PSC controller holds SS low until the flag is set. However, the flag was set always on the last byte of the FIFO, independently if it is the last byte of the transfer. This generates spurious toggling of the SS signals that breaks the protocol of some peripherals. Fix. Signed-off-by: Stefano Babic <sbabic@denx.de> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-01spi: avoid spidev crash when device is removedWolfgang Ocker
I saw a kernel oops in spidev_remove() when a spidev device was registered and I unloaded the SPI master driver: Unable to handle kernel paging request for data at address 0x00000004 Faulting instruction address: 0xc01c0c50 Oops: Kernel access of bad area, sig: 11 [#1] CDSPR Modules linked in: spi_ppc4xx(-) NIP: c01c0c50 LR: c01bf9e4 CTR: c01c0c34 REGS: cec89c30 TRAP: 0300 Not tainted (2.6.27.3izt) MSR: 00021000 <ME> CR: 24000228 XER: 20000007 DEAR: 00000004, ESR: 00800000 TASK = cf889040[2070] 'rmmod' THREAD: cec88000 GPR00: 00000000 cec89ce0 cf889040 cec8e000 00000004 cec8e000 ffffffff 00000000 GPR08: 0000001c c0336380 00000000 c01c0c34 00000001 1001a338 100e0000 100df49c GPR16: 100b54c0 100df49c 100ddd20 100f05a8 100b5340 100efd68 00000000 00000000 GPR24: 100ec008 100f0428 c0327788 c0327794 cec8e0ac cec8e000 c0336380 00000000 NIP [c01c0c50] spidev_remove+0x1c/0xe4 LR [c01bf9e4] spi_drv_remove+0x2c/0x3c Call Trace: [cec89d00] [c01bf9e4] spi_drv_remove+0x2c/0x3c [cec89d10] [c01859a0] __device_release_driver+0x78/0xb4 [cec89d20] [c0185ab0] device_release_driver+0x28/0x44 [cec89d40] [c0184be8] bus_remove_device+0xac/0xd8 [cec89d60] [c0183094] device_del+0x100/0x194 [cec89d80] [c0183140] device_unregister+0x18/0x30 [cec89da0] [c01bf30c] __unregister+0x20/0x34 [cec89db0] [c0182778] device_for_each_child+0x38/0x74 [cec89de0] [c01bf2d0] spi_unregister_master+0x28/0x44 [cec89e00] [c01bfeac] spi_bitbang_stop+0x1c/0x58 [cec89e20] [d908a5e0] spi_ppc4xx_of_remove+0x24/0x7c [spi_ppc4xx] [...] IMHO a call to spi_set_drvdata() is missing in spidev_probe(). The patch below helped. Signed-off-by: Wolfgang Ocker <weo@reccoware.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-01hwmon: applesmc: make applesmc load automatically on startupHenrik Rydberg
make use of the new dmi device loading support to automatically load the applesmc driver based on the dmi_match table. Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Cc: Nicolas Boichat <nicolas@boichat.ch> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-01parport_serial: fix array overflowTakashi Iwai
The netmos_9xx5_combo type assumes that PCI SSID provides always the correct value for the number of parallel and serial ports, but there are indeed broken devices with wrong numbers, which may result in Oops. This patch simply adds the check of the array range. Reference: Novell bnc#447067 https://bugzilla.novell.com/show_bug.cgi?id=447067 Signed-off-by: Takashi Iwai <tiwai@suse.de> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-01em28xx: remove backward compat macro added on a previous fixMauro Carvalho Chehab
commit 50f3beb50abe0cc0228363af804e50e710b3e5b0 fixed em28xx-alsa locking schema. However, a backport macro was kept. This patch removes the macro, since it is not needed for the module compilation against upstream. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2008-12-01Merge branch 'upstream-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: libata: blacklist Seagate drives which time out FLUSH_CACHE when used with NCQ [libata] pata_rb532_cf: fix signature of the xfer function [libata] pata_rb532_cf: fix and rename register definitions ata_piix: add borked Tecra M4 to broken suspend list
2008-12-01V4L/DVB (9748): em28xx: fix compile warningHans Verkuil
Label fail_unreg is no longer used. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2008-12-01V4L/DVB (9743): em28xx: fix oops audioDouglas Schilling Landgraf
Replaced usb_kill_usb for usb_unlink_usb (wait until urb to fully stop require USB core to put the calling process to sleep). Oops: http://www.kerneloops.org/raw.php?rawid=71799&msgid= Signed-off-by: Douglas Schilling Landgraf <dougsland@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2008-12-01Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: IB/mlx4: Fix MTT leakage in resize CQ IB/ehca: Fix problem with generated flush work completions IB/ehca: Change misleading error message on memory hotplug mlx4_core: Save/restore default port IB capability mask
2008-12-01libata: blacklist Seagate drives which time out FLUSH_CACHE when used with NCQTejun Heo
Some recent Seagate harddrives have firmware bug which causes FLUSH CACHE to timeout under certain circumstances if NCQ is being used. This can be worked around by disabling NCQ and fixed by updating the firmware. Implement ATA_HORKAGE_FIRMWARE_UPDATE and blacklist these devices. The wiki page has been updated to contain information on this issue. http://ata.wiki.kernel.org/index.php/Known_issues Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-12-01[libata] pata_rb532_cf: fix signature of the xfer functionPhil Sutter
Per definition, this function should return the number of bytes consumed. As the original parameter "buflen" is being decremented inside the read/write loop, save it in "retlen" at the beginning. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Acked-by: Sergei Shtyltov <sshtylyov@ru.mvista.com> Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Acked-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-12-01[libata] pata_rb532_cf: fix and rename register definitionsPhil Sutter
The original standalone driver uses a custom address for the error register. Use it in pata_rb532_cf, too. Rename two register definitions: - The address offset 0x0800 in fact is the ATA base, not ATA command address. - The offset 0x0C00 is not a regular ATA data address, but a buffered one allowing 4-byte IO. Signed-off-by: Phil Sutter <n0-1@freewrt.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-12-01ata_piix: add borked Tecra M4 to broken suspend listTejun Heo
Tecra M4 sometimes forget what it is and reports bogus data via DMI which makes the machine evade broken suspend matching and thus fail suspend/resume. This patch updates piix_broken_suspend() such that it can match such case. As the borked DMI data is a bit generic, matching many entries to make the match more specific is necessary. As the usual DMI matching is limited to four entries, this patch uses hard coded manual matching. This is reported by Alexandru Romanescu. Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Alexandru Romanescu <a_romanescu@yahoo.co.uk> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-12-01Merge branches 'ehca' and 'mlx4' into for-linusRoland Dreier
2008-12-01IB/mlx4: Fix MTT leakage in resize CQJack Morgenstein
When resizing a CQ, MTTs associated with the old CQE buffer were not freed. As a result, if any app used resize CQ repeatedly, all MTTs were eventually exhausted, which led to all memory registration operations failing until the driver is reloaded. Once the RESIZE_CQ command returns successfully from FW, FW no longer accesses the old CQ buffer, so it is safe to deallocate the MTT entries used by the old CQ buffer. Finally, if the RESIZE_CQ command fails, the MTTs allocated for the new CQEs buffer also need to be de-allocated. This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1416>. Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-12-01IB/ehca: Fix problem with generated flush work completionsStefan Roscher
This fix enables ehca device driver to generate flush work completions even if the application doesn't request completions for all work requests. The current implementation of ehca will generate flush work completions for the wrong work requests if an application uses non signaled work completions. Signed-off-by: Stefan Roscher <stefan.roscher@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-12-01IB/ehca: Change misleading error message on memory hotplugJoachim Fenkes
The error message printed when the eHCA driver prevents memory hotplug is misleading -- the user might think that hot-removing the lhca, hotplugging memory, then hot-adding the lhca again will work, but it actually doesn't. Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-12-01Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: ieee1394: sbp2: fix race condition in state change ieee1394: fix list corruption (reported at module removal) firewire: fw-sbp2: another iPod mini quirk entry ieee1394: sbp2: another iPod mini quirk entry
2008-12-01[SCSI] stex: switch to block timeoutJames Bottomley
stex sets the timeout in its slave configure routine for all devices. This now needs to update the request queue timeout in block. Cc: Ed Lin <ed.lin@promise.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-12-01[SCSI] make scsi_eh_try_stu use block timeoutJames Bottomley
scsi_eh_try_stu() was still using the timeout parameter in the device which is now not set (i.e. zero filled) meaning that it waited no time at all for the start unit command to complete (leading the routine to conclude failure every time). This lead to a 2.6.27 regression: http://bugzilla.kernel.org/show_bug.cgi?id=12120 Where firewire devices that were non spec compliant wouldn't spin up. Fix this by using the block queue timeout value instead. Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-12-01[SCSI] megaraid_sas: switch to block timeoutJames Bottomley
megaraid_sas sets the timeout in its slave configure routine for devices on special channels. This now needs to update the request queue timeout in block. Cc: "Yang, Bo" <Bo.Yang@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-12-01[SCSI] ibmvscsi: switch to block timeoutJames Bottomley
ibmvscsi sets the timeout in its slave configure routine for disk devices. This now needs to update the request queue timeout in block. Cc: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-11-24 15:44:42 +0000