summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)Author
2010-01-10vxge: use pci_dma_mapping_error to test return valueDenis Kirjanov
pci_dma_mapping_error should be used to test return value of pci_map_single or pci_map_page. Signed-off-by: Denis Kirjanov <kirjanov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08e1000e: fix and commonize code for setting the receive address registersBruce Allan
Fix e1000e_rar_set() to flush consecutive register writes to avoid write combining which some parts cannot handle. Update e1000e_init_rx_addrs() to call the fixed e1000e_rar_set() instead of duplicating code. Also change e1000e_rar_set() to _not_ set the Address Valid bit if the MAC address is all zeros. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08e1000e: e1000e_enable_tx_pkt_filtering() returns wrong valueBruce Allan
e1000e_enable_tx_pkt_filtering() will return a non-zero value if the driver fails to enable the manageability interface on the host for any reason; instead it should retun zero to indicate filtering has been disabled. Also provide a single exit point for the function. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08e1000e: perform 10/100 adaptive IFS only on parts that support itBruce Allan
Adaptive IFS which involves writing to the Adaptive IFS Throttle register was being done for all devices supported by the driver even though it is not supported (i.e. the register doesn't even exist) on some devices. The feature is supported on 8257x/82583 and ICH/PCH based devices, but not on ESB2. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08e1000e: don't accumulate PHY statistics on PHY read failureBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08e1000e: call pci_save_state() after pci_restore_state()Bruce Allan
Due to a change in pci_restore_state()[1] which clears the saved_state flag, the driver should call pci_save_state() to set the flag once again to avoid issues with EEH (same fix that recently was submitted for ixgbe). [1] commmit 4b77b0a2ba27d64f58f16d8d4d48d8319dda36ff Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08netxen: update version to 4.0.72Amit Kumar Salecha
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08netxen: fix set mac addrAmit Kumar Salecha
o If tx and rx resources are not available, during set mac request. Then this request wont be passed to firmware and it will be added to driver mac list and will never make it to firmware. So if resources are not available, don't add it to driver mac list. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08netxen: fix smatch warningAmit Kumar Salecha
o Fix pointless assignments Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-08netxen: fix tx ring memory leakAmit Kumar Salecha
o While unloading driver or resetting the context, tx ring was not getting free. Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07TI DaVinci EMAC: Handle emac module clock correctly.Sriram
In the driver probe function the emac module clock needs to be enabled before calling register_netdev(). As soon as the device is registered the driver get_stats function can be invoked by the core - the module clock must be switched on to be able to read from stats registers. Also explicitly call matching clk_disable for failure conditions in probe function. Signed-off-by: Sriramakrishnan <srk@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07dmfe/tulip: Let dmfe handle DM910x except for SPARC on-board chipsBen Hutchings
The Davicom DM9100 and DM9102 chips are used on the motherboards of some SPARC systems (supported by the tulip driver) and also in PCI expansion cards (supported by the dmfe driver). There is no difference in the PCI device ids for the two different configurations, so these drivers both claim the device ids. However, it is possible to distinguish the two configurations by the presence of Open Firmware properties for them, so we do that. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Grant Grundler <grundler@parisc-linux.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07ixgbe: Fix compiler warning about variable being used uninitializedPJ Waskiewicz
tc is still throwing a warning that is could be used uninitialized. This fixes it, and properly formats the device ID checks for the use of this variable. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07mv643xx_eth: don't include cache padding in rx desc buffer sizeSaeed Bishara
If NET_SKB_PAD is not a multiple of the cache line size, mv643xx_eth allocates a couple of extra bytes at the start of each receive buffer to make the data payload end up on a cache line boundary. These extra bytes are skb_reserve()'d before DMA mapping, so they should not be included in the DMA map byte count (as the mapping is done starting at skb->data), nor should they be included in the receive descriptor buffer size field, or the hardware can end up DMAing beyond the end of the buffer, which can happen if someone sends us a larger-than-MTU sized packet. This problem was introduced in commit 7fd96ce47ff ("mv643xx_eth: rework receive skb cache alignment", May 6 2009), but hasn't appeared to be problematic so far, probably as the main users of mv643xx_eth all have NET_SKB_PAD == L1_CACHE_BYTES. Signed-off-by: Saeed Bishara <saeed@marvell.com> Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07NET: atlx, fix memory leakJiri Slaby
Stanse found a memory leak in atl2_get_eeprom. eeprom_buff is not freed/assigned on all paths. Fix that. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Jay Cliburn <jcliburn@gmail.com> Cc: Chris Snook <chris.snook@gmail.com> Cc: Jie Yang <jie.yang@atheros.com> Cc: atl1-devel@lists.sourceforge.net Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07pcmcia: ncmlan_cs: remove odd bracketAlexander Beregalov
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07cs89x0: Always report failure to request interruptMark Brown
A failure on request_irq() is always fatal but unlike other fatal errors it's only reported to the user if net_debug is set. Make the diagnostic unconditional and raise the priority so that errors are more obvious to the user. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07hso: fixed missing newlinesJan Dumon
Fixed missing newlines in calls to dev_warn & dev_err. Signed-off-by: Jan Dumon <j.dumon@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07hso: Fix for 5 sec timeouts with v2.x firmwareJan Dumon
Don't send flow control settings to any port other than the modem port. Older firmware ignored this request but did sent a reply. Newer firmware just ignores it without reply and causes a 5 second timeout every time a port (except for the modem port) is opened or if tiocm settings are changed. Signed-off-by: Jan Dumon <j.dumon@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07hso: Attempt to recover from usb bus errorsJan Dumon
Attempt to reset the usb device when we receive usb bus errors. Signed-off-by: Jan Dumon <j.dumon@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07hso: don't change the state of a closed portJan Dumon
Don't change the state of a port if it's not open. This fixes an issue where a port sometimes has to be opened twice before data can be received. Signed-off-by: Jan Dumon <j.dumon@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07hso: Fix for endian issues on big endian machinesJan Dumon
Some fields are always little endian and have to be converted on big endian machines. Signed-off-by: Jan Dumon <j.dumon@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07hso: Add Vendor/Product ID's for new devicesJan Dumon
Add product ID's for new devices. Signed-off-by: Jan Dumon <j.dumon@option.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-07claw: use "claw" as root device nameUrsula Braun
Claw module cannot be loaded together with qeth, because "qeth" has been errorneously used as root device name. It is changed into "claw". Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-06pcnet_cs: add cis of KTI PE520 pcmcia network cardKen Kawasaki
pcnet_cs,serial_cs: add cis of KTI PE520 pcmcia network card, and serial card(Sierra Wireless AC860). Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-06ucc_geth: Fix the wrong the Rx/Tx FIFO sizeDave Liu
current the Rx/Tx FIFO size settings cause problem when four UEC ethernets work simultaneously. eg: GETH1, UEM-J15, GETH2, UEC-J5 on 8569MDS board $ ifconfig eth0 10.193.20.166 $ ifconfig eth1 10.193.20.167 $ ifconfig eth2 10.193.20.168 then $ ifconfig eth3 10.193.20.169 The fourth ethernet will cause all of interface broken, you cann't ping successfully any more. The patch fix this issue for MPC8569 Rev1.0 and Rev2.0 Signed-off-by: Dave Liu <daveliu@freescale.com> Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-04cxgb3i: Fix flags test.David S. Miller
As noticed by Stephen Rothwell. Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03netxen: fix ethtool link testSucheta Chakraborty
o Fix ethtool link test for NX3031 chip. o Remove unused code from phy interrupt callback Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03netxen: fix ethtool register dumpSucheta Chakraborty
o Dump registers such as tx ring and rx ring counter, firmware state, niu regs, etc. which can be useful for debugging purpose. Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com> Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03rrunner: fix buffer overflowDan Carpenter
tx_skbuff is define as: struct sk_buff *tx_skbuff[TX_RING_ENTRIES]; EVT_RING_ENTRIES is 64 and TX_RING_ENTRIES is 32. This function is in a error path so that's why it wasn't noticed. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03broadcom: Fix &&/|| confusion in bcm54xx_adjust_rxrefclk()roel kluin
This always evaluates to true. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03net: Test off by one in sh_eth_reset()roel kluin
If no break occurred, cnt reaches 0 after the loop. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03niu: timeout ignored in tcam_wait_bit()roel kluin
With `while (--limit > 0)' i reaches 0 after the loop, so upon timeout the error was not returned. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03atarilance: timeout ignored in lance_open()roel kluin
With `while (--i > 0)' i reaches 0 after the loop, so upon timeout the error was not issued. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03drivers/net : Correct the size argument to kzallocJulia Lawall
lp->rx_skb has type struct sk_buff **, not struct sk_buff *, so the elements of the array should have pointer type, not structure type. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @disable sizeof_type_expr@ type T; T **x; @@ x = <+...sizeof( - T + *x )...+> // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03cxgb3i: Fix a login over vlan issueRakesh Ranjan
Fix a target login issue, when parent interface is vlan and we are using cxgb3i sepecific private ip address in '/etc/iscsi/ifaces/' iface file. Acked-by: Karen Xie <kxie@chelsio.com> Signed-off-by: Rakesh Ranjan <rakesh@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03hamradio: avoid null deref v3Dan Carpenter
This should address the problems in version 1 (lazy) and version 2 (ugly). Bump the stats on orig_dev not on the newly assigned NULL dev variable. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03usbnet: test off by oneroel kluin
With `while (i++ < MII_TIMEOUT)' i reaches MII_TIMEOUT + 1 after the loop This is probably unlikely a problem in practice. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03drivers/net/can: Correct NULL testJulia Lawall
Test the just-allocated value for NULL rather than some other value. The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression x,y; statement S; @@ x = \(kmalloc\|kcalloc\|kzalloc\)(...); ( if ((x) == NULL) S | if ( - y + x == NULL) S ) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03drivers/isdn: eliminate duplicated testJulia Lawall
The code checked slot_rx twice. Check slot_tx by analogy with the bank case. The semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression E; @@ ( *E && E | *E || E ) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-03via-velocity: Give RX descriptors to the NIC later on open or MTU changeBen Hutchings
velocity_open() calls velocity_give_many_rx_descs(), which gives RX descriptors to the NIC, before installing an interrupt handler or calling velocity_init_registers(). I think this is very unsafe and it appears to explain the bug report <http://bugs.debian.org/508527>. On MTU change, velocity_give_many_rx_descs() is again called before velocity_init_registers(). I'm not sure whether this is unsafe but it does look wrong. Therefore, move the calls to velocity_give_many_rx_descs() after request_irq() and velocity_init_registers(). Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Tested-by: Jan Ceuleers <jan.ceuleers@computer.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-30fsl_pq_mdio: Fix iomem unmapping for non-eTSEC2.0 controllersAnton Vorontsov
We use a rather complicated logic to support eTSEC and eTSEC2.0 registers maps in a single driver. Currently, the code tries to unmap 'regs', but for non-eTSEC2.0 controllers 'regs' doesn't point to a mapping start, and this might cause badness on probe failure or module removal: Freescale PowerQUICC MII Bus: probed Trying to vfree() nonexistent vm area (e107f000) ------------[ cut here ]------------ Badness at c00a7754 [verbose debug info unavailable] NIP: c00a7754 LR: c00a7754 CTR: c02231ec [...] NIP [c00a7754] __vunmap+0xec/0xf4 LR [c00a7754] __vunmap+0xec/0xf4 Call Trace: [df827e50] [c00a7754] __vunmap+0xec/0xf4 (unreliable) [df827e70] [c001519c] iounmap+0x44/0x54 [df827e80] [c028b924] fsl_pq_mdio_probe+0x1cc/0x2fc [df827eb0] [c02fb9b4] of_platform_device_probe+0x5c/0x84 [df827ed0] [c0229928] really_probe+0x78/0x1a8 [df827ef0] [c0229b20] __driver_attach+0xa4/0xa8 Fix this by introducing a proper priv structure (finally!), which now holds 'regs' and 'map' fields separately. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-30ucc_geth: Fix netdev watchdog triggering on suspendAnton Vorontsov
Sometimes ucc_geth fails to suspend with the following trace: ucc_geth e0103000.ucc: suspend ucc_geth e0102000.ucc: suspend NETDEV WATCHDOG: eth0 (ucc_geth): transmit queue 0 timed out ------------[ cut here ]------------ Badness at net/sched/sch_generic.c:255 NIP: c021cb5c LR: c021cb5c CTR: c01ab4b4 [...] NIP [c021cb5c] dev_watchdog+0x298/0x2a8 LR [c021cb5c] dev_watchdog+0x298/0x2a8 Call Trace: [c0389da0] [c021cb5c] dev_watchdog+0x298/0x2a8 (unreliable) [c0389e00] [c0031ed8] run_timer_softirq+0x16c/0x1dc [c0389e50] [c002c638] __do_softirq+0xa4/0x11c [...] This patch fixes the issue by properly detaching the device on suspend, and attaching it back on resume. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-30phylib: Properly reinitialize PHYs after hibernationAnton Vorontsov
Since hibernation assumes power loss, we should fully reinitialize PHYs (including platform fixups), as if PHYs were just attached. This patch factors phy_init_hw() out of phy_attach_direct(), then converts mdio_bus to dev_pm_ops and adds an appropriate restore() callback. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-30phylib: Fix deadlock on resumeAnton Vorontsov
Sometimes kernel hangs on resume with the following trace: ucc_geth e0102000.ucc: resume INFO: task bash:1764 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. bash D 0fecf43c 0 1764 1763 0x00000000 Call Trace: [cf9a7c10] [c0012868] ret_from_except+0x0/0x14 (unreliable) --- Exception: cf9a7ce0 at __switch_to+0x4c/0x6c LR = 0xcf9a7cc0 [cf9a7cd0] [c0008c14] __switch_to+0x4c/0x6c (unreliable) [cf9a7ce0] [c028bcfc] schedule+0x158/0x260 [cf9a7d10] [c028c720] __mutex_lock_slowpath+0x80/0xd8 [cf9a7d40] [c01cf388] phy_stop+0x20/0x70 [cf9a7d50] [c01d514c] ugeth_resume+0x6c/0x13c [...] Here is why. On suspend: - PM core starts suspending devices, ucc_geth_suspend gets called; - ucc_geth calls phy_stop() on suspend. Note that phy_stop() is mostly asynchronous so it doesn't block ucc_geth's suspend routine, it just sets PHY_HALTED state and disables PHY's interrupts; - Suddenly the state machine gets scheduled, it grabs the phydev->lock mutex and tries to process the PHY_HALTED state, so it calls phydev->adjust_link(phydev->attached_dev). In ucc_geth case adjust_link() calls msleep(), which reschedules the code flow back to PM core, which now finishes suspend and so we end up sleeping with phydev->lock mutex held. On resume: - PM core starts resuming devices (notice that nobody rescheduled the state machine yet, so the mutex is still held), the core calls ucc_geth's resume routine; - ucc_geth_resume restarts the PHY with phy_stop()/phy_start() sequence, and the phy_*() calls are trying to grab the phydev->lock mutex. Here comes the deadlock. This patch fixes the issue by stopping the state machine on suspend and starting it again on resume. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-12-29Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2009-12-29Revert "b43: Enforce DMA descriptor memory constraints"John W. Linville
This reverts commit 9bd568a50c446433038dec2a5186c5c57c3dbd23. That commit is shown to cause allocation failures during initialization on some machines. http://bugzilla.kernel.org/show_bug.cgi?id=14844 Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28iwmc3200wifi: fix array out-of-boundary accessZhu Yi
Allocate priv->rx_packets[IWM_RX_ID_HASH + 1] because the max array index is IWM_RX_ID_HASH according to IWM_RX_ID_GET_HASH(). Cc: stable@kernel.org Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28wl1251: timeout one too soon in wl1251_boot_run_firmware()Roel Kluin
`loop' reaches INIT_LOOP + 1 after the loop. so if ACX_INTR_INIT_COMPLETE occurs in the last iteration the write occurs but also the error out as if a timeout occurred. This is probably very unlikely to ever occur. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Kalle Valo <kalle.valo@nokia.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-12-28ath9k: fix missed error codes in the tx status checkFelix Fietkau
My previous change added in: commit 815833e7ecf0b9a017315cae6aef4d7cd9517681 ath9k: fix tx status reporting was not checking all possible tx error conditions. This could possibly lead to throughput issues due to slow rate control adaption or missed retransmissions of failed A-MPDU frames. This patch adds a mask for all possible error conditions and uses it in the xmit ok check. Cc: stable@kernel.org Reported-by: Björn Smedman <bjorn.smedman@venatech.se> Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-10-06 00:24:30 +0000