Age | Commit message (Collapse) | Author |
|
A0 hybrid steering is a form of high performance flow steering.
By using this mode, mlx4 cards use a fast limited table based steering,
in order to enable fast steering of unicast packets to a QP.
In order to implement A0 hybrid steering we allocate resources
from different zones:
(1) General range
(2) Special MAC-assigned QPs [RSS, Raw-Ethernet] each has its own region.
When we create a rss QP or a raw ethernet (A0 steerable and BF ready) QP,
we try hard to allocate the QP from range (2). Otherwise, we try hard not
to allocate from this range. However, when the system is pushed to its
limits and one needs every resource, the allocator uses every region it can.
Meaning, when we run out of raw-eth qps, the allocator allocates from the
general range (and the special-A0 area is no longer active). If we run out
of RSS qps, the mechanism tries to allocate from the raw-eth QP zone. If that
is also exhausted, the allocator will allocate from the general range
(and the A0 region is no longer active).
Note that if a raw-eth qp is allocated from the general range, it attempts
to allocate the range such that bits 6 and 7 (blueflame bits) in the
QP number are not set.
When the feature is used in SRIOV, the VF has to notify the PF what
kind of QP attributes it needs. In order to do that, along with the
"Eth QP blueflame" bit, we reserve a new "A0 steerable QP". According
to the combination of these bits, the PF tries to allocate a suitable QP.
In order to maintain backward compatibility (with older PFs), the PF
notifies which QP attributes it supports via QUERY_FUNC_CAP command.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The zone allocator is a mechanism which manages a few mlx4_bitmaps.
When allocating a resource, the user indicates the desired zone of
which this resource will be allocated from. If possible, the resource
will be allocated from this zone. Otherwise, the resource will be
allocated from a less-than, equal-to, higher-than priority zone,
according to the desired zone's properties with that respective
allocation order.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The number of reserved QPs is affected both from the firmware and
from the driver's requirements. This patch adds a check that
validates that this number is indeed feasable.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using BF (Blue-Flame), the QPN overrides the VLAN, CV, and SV fields
in the WQE. Thus, BF may only be used for QPNs with bits 6,7 unset.
The current Ethernet driver code reserves a Tx QP range with 256b alignment.
This is wrong because if there are more than 64 Tx QPs in use,
QPNs >= base + 65 will have bits 6/7 set.
This problem is not specific for the Ethernet driver, any entity that
tries to reserve more than 64 BF-enabled QPs should fail. Also, using
ranges is not necessary here and is wasteful.
The new mechanism introduced here will support reservation for
"Eth QPs eligible for BF" for all drivers: bare-metal, multi-PF, and VFs
(when hypervisors support WC in VMs). The flow we use is:
1. In mlx4_en, allocate Tx QPs one by one instead of a range allocation,
and request "BF enabled QPs" if BF is supported for the function
2. In the ALLOC_RES FW command, change param1 to:
a. param1[23:0] - number of QPs
b. param1[31-24] - flags controlling QPs reservation
Bit 31 refers to Eth blueflame supported QPs. Those QPs must have
bits 6 and 7 unset in order to be used in Ethernet.
Bits 24-30 of the flags are currently reserved.
When a function tries to allocate a QP, it states the required attributes
for this QP. Those attributes are considered "best-effort". If an attribute,
such as Ethernet BF enabled QP, is a must-have attribute, the function has
to check that attribute is supported before trying to do the allocation.
In a lower layer of the code, mlx4_qp_reserve_range masks out the bits
which are unsupported. If SRIOV is used, the PF validates those attributes
and masks out unsupported attributes as well. In order to notify VFs which
attributes are supported, the VF uses QUERY_FUNC_CAP command. This command's
mailbox is filled by the PF, which notifies which QP allocation attributes
it supports.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, we've fired all our completion callbacks straight from our ISR.
Some of those callbacks were lightweight (for example, mlx4_en's and
IPoIB napi callbacks), but some of them did more work (for example,
the user-space RDMA stack uverbs' completion handler). Besides that,
doing more than the minimal work in ISR is generally considered wrong,
it could even lead to a hard lockup of the system. Since when a lot
of completion events are generated by the hardware, the loop over those
events could be so long, that we'll get into a hard lockup by the system
watchdog.
In order to avoid that, add a new way of invoking completion events
callbacks. In the interrupt itself, we add the CQs which receive completion
event to a per-EQ list and schedule a tasklet. In the tasklet context
we loop over all the CQs in the list and invoke the user callback.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When VFs (guests in this context) issue the QUERY_DEV_CAP command, they
need not be told that host side virtualization features such as VST, FSM
(MAC anti-spoofing) and running > 80 VFs are supported by the device.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was dropped by mistake for the napi_gro_frags flow, fix that.
Fixes: dd65beac48a5 ('net/mlx4_en: Extend usage of napi_gro_frags')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
- Clean-up leaky resources; pwm_bl
- Simplify Device Tree initialisation; lp855x_bl
- Add Regulator support; lp855x
- Remove Bryan from the Maintainer list -- new baby, no time :)
* tag 'backlight-for-linus-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
MAINTAINERS: Remove my name from Backlight subsystem
backlight: lp855x: Add supply regulator to lp855x
backlight: lp855x: Refactor DT parsing code
backlight: pwm: Clean-up pwm requested using legacy API
|
|
The encapsulated offload flags shouldn't be unconditionally exported
to the stack. The stack expects offloading to work across all tunnel
types when those flags are set. This would break other tunnels (like
GRE) since be2net currently supports tunnel offload for VxLAN only.
Also, with VxLANs Skyhawk-R can offload only 1 UDP dport. If more
than 1 UDP port is added, we should disable offloads in that case too.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to use dma_mapping_error() to check the dma address returned
by dma_map_single/page(). Otherwise we would get warning like this:
WARNING: at lib/dma-debug.c:1140
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.18.0-rc2-next-20141029 #196
task: c0834300 ti: effe6000 task.ti: c0874000
NIP: c02b2c98 LR: c02b2c98 CTR: c030abc4
REGS: effe7d70 TRAP: 0700 Not tainted (3.18.0-rc2-next-20141029)
MSR: 00021000 <CE,ME> CR: 22044022 XER: 20000000
GPR00: c02b2c98 effe7e20 c0834300 00000098 00021000 00000000 c030b898 00000003
GPR08: 00000001 00000000 00000001 749eec9d 22044022 1001abe0 00000020 ef278678
GPR16: ef278670 ef278668 ef278660 070a8040 c087f99c c08cdc60 00029000 c0840d44
GPR24: c08be6e8 c0840000 effe7e78 ef041340 00000600 ef114e10 00000000 c08be6e0
NIP [c02b2c98] check_unmap+0x51c/0x9e4
LR [c02b2c98] check_unmap+0x51c/0x9e4
Call Trace:
[effe7e20] [c02b2c98] check_unmap+0x51c/0x9e4 (unreliable)
[effe7e70] [c02b31d8] debug_dma_unmap_page+0x78/0x8c
[effe7ed0] [c03d1640] gfar_clean_rx_ring+0x208/0x488
[effe7f40] [c03d1a9c] gfar_poll_rx_sq+0x3c/0xa8
[effe7f60] [c04f8714] net_rx_action+0xc0/0x178
[effe7f90] [c00435a0] __do_softirq+0x100/0x1fc
[effe7fe0] [c0043958] irq_exit+0xa4/0xc8
[effe7ff0] [c000d14c] call_do_irq+0x24/0x3c
[c0875e90] [c00048a0] do_IRQ+0x8c/0xf8
[c0875eb0] [c000ed10] ret_from_except+0x0/0x18
For TX, we need to unmap the pages which has already been mapped and
free the skb before return.
For RX, move the dma mapping and error check to gfar_new_skb(). We
would reuse the original skb in the rx ring when either allocating
skb failure or dma mapping error.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove use of calls into t4_fw_hello() with MASTER_MUST, which results in
FW_HELLO_CMD_MASTERFORCE being set. The firmware doesn't support this and of
course any existing PF Drivers will totally go for a toss.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
"Here is a stash of pin control changes I have collected for the v3.19
series. Mainly new hardware support, with Intels new embedded SoC as
the especially interesting thing standing out, fully using the
subsystem.
- Force conversion of the ux500 pin control device trees and parsers
to use the generic pin control bindings.
- New driver and device tree bindings for the Qualcomm PMIC MPP pin
controller and GPIO.
- Some ACPI infrastructure for pin controllers.
- New driver for the Intel CherryView/Braswell pin controller, the
first Intel pin controller to fully take advantage of the pin
control subsystem.
- Support the Freescale i.MX VF610 variant.
- Support the sunxi A80 variant.
- Support the Samsung Exynos 4415 and Exynos 7 variants.
- Split out Intel pin controllers to their own subdirectory.
- A large slew of rockchip pin control updates, including
suspend/resume support.
- A large slew of Samsung Exynos pin controller updates.
- Various minor updates and fixes"
* tag 'pinctrl-v3.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (49 commits)
pinctrl: at91: enhance (debugfs) at91_gpio_dbg_show
pinctrl: meson: add device tree bindings documentation
gpio: tz1090: Fix error handling of irq_of_parse_and_map
pinctrl: tz1090-pinctrl.txt: Fix typo in binding
pinctrl: pinconf-generic: Declare dt_params/conf_items const
pinctrl: exynos: Add support for Exynos4415
pinctrl: exynos: Add initial driver data for Exynos7
pinctrl: exynos: Add irq_chip instance for Exynos7 wakeup interrupts
pinctrl: exynos: Consolidate irq domain callbacks
pinctrl: exynos: Generalize the eint16_31 demux code
pinctrl: samsung: Separate per-bank init and runtime data
pinctrl: samsung: Constify samsung_pin_ctrl struct
pinctrl: samsung: Constify samsung_pin_bank_type struct
pinctrl: samsung: Drop unused label field in samsung_pin_ctrl struct
pinctrl: samsung: Make samsung_pinctrl_get_soc_data use ERR_PTR()
pinctrl: Add Intel Cherryview/Braswell pin controller support
gpio / ACPI: Add knowledge about pin controllers to acpi_get_gpiod()
pinctrl: Fix path error in documentation
pinctrl: rockchip: save and restore gpio6_c6 pinmux in suspend/resume
pinctrl: rockchip: add suspend/resume functions
...
|
|
Legacy drivers use virtio_pci_common.h too, we should not
define VIRTIO_PCI_NO_LEGACY there.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
virtio 1.0 devices require that drivers set VIRTIO_CONFIG_S_FEATURES_OK
after finalizing features.
virtio core missed doing this on restore, fix it up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
* fixes:
PM / OPP: remove double calls to find_device_opp()
PM / OPP: set new_opp->dev_opp to a valid dev_opp
leds: leds-gpio: Fix the "default-state" property check
|
|
After Hot-remove of a device with a mounted partition,
when the device is hot-added again, the new node reappears
as nvme0n1. Mounting this new node fails with the error:
mount: mount /dev/nvme0n1p1 on /mnt failed: File exists.
The old nodes's FS entries still exist and the kernel can't re-create
procfs and sysfs entries for the new node with the same name.
The patch fixes this issue.
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Indraneel M <indraneel.m@samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
irq_mask should include all IRQ bits that we want to mask, but atm we
set it incorrectly to the inverse of this. If the mask is used
subsequently to enable/disable some IRQ bits, we may unintentionally
unmask unrelated IRQs. I can't see any way that this can lead to a real
problem in the current -nightly code, since the first place the mask
will be used next (after a suspend/resume cycle) is in
valleyview_irq_postinstall(), but the mask is reset there to its proper
value.
This causes a problem in the upstream kernel though, where - due to another
issue - the mask is used in the above way to disable only the display IRQs.
This other issue is fixed by:
commit 950eabaf5a87257040e0c207be09487954113f54
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Sep 8 15:21:09 2014 +0300
drm/i915: vlv: fix display IRQ enable/disable
Interestingly, even with the above two bugs, we shouldn't in theory have
any real problems (arguably a famous last sentence:). That's because
even if we unmask something unintentionally via the VLV_IMR/VLV_IER
register the master IRQ masking bit in VLV_MASTER_IER is still set and
should prevent all i915 interrupts. According to my testing on an ASUS
T100 with DSI output this isn't the case at least with the
MIPIA_INTERRUPT. Leaving this one unmasked in IMR/IER, while having
VLV_MASTER_IER set to 0 may lead to a lockup during system suspend as
shown in the bugzilla ticket below. This fix should get rid of the
problem reported there in upstream and older kernels.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85920
Cc: stable@vger.kernel.org (v3.15+)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Should probably just init this in the GMbus code all the time, based on
the cdclk and HPLL like we do on newer platforms. Ville has code for
that in a rework branch, but until then we can fix this bug fairly
easily.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76301
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Nikolay <mar.kolya@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
When bind failed make sure that CRTC and planes are
completely clean up to avoid properties duplication.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
|
|
High Quality Video Data Plane is hardware IP dedicated
to video rendering. Compare to GPD (graphic planes) it
have better scaler capabilities.
HQVDP use VID layer to push data into hardware compositor
without going into DDR. From data flow point of view HQVDP
and VID are nested so HQVPD update/disable VID.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
|
|
stih407 SoC have a dedicated hardware cursor plane,
this patch enable it.
The hardware have a color look up table, fix it to
be able to use ARGB8888.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
|
|
For stih407 SoC enable the second mixer to get two CRTC.
Allow GPD planes and encoders to be connected to this new CRTC.
Cursor plane can only be set on first CRTC.
GPD clocks needed change the parent clock depending on which
CRTC GPD are used.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
|
|
The HDMI path introduce a delay of 6 pixels.
This delay should be take into account while programming
VTG for the HDMI. Without this delay, the HDMI active
window area is shift of 6 pixel on the right.
Set also timing for DVO output.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
|
|
Change some functions prototype to prepare the introduction of
auxiliary crtc. It will also help to have a DVO encoder.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
|
|
Make sure that vblank is enabled when crtc commit is call.
Replace drm_vblank_off() by drm_crtc_vblank_off()
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
|
|
The hardware expect to have the infoframe checksum in the first byte.
In consequence shift all infoframe on one byte.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
|
|
Stop use event_lock in vblank disable function.
This was creating a dead lock.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
|
|
Store the physical address at node creation time
to avoid use of virt_to_dma and dma_to_virt everywhere
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
|
|
Make sure that mixer control register is correctly reset
before use it.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
|
|
gpio used for HDMI hot plug detection is useless,
HDMI_STI register contains an hot plug detection status bit.
Fix binding documentation.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
|
|
Depending of the board configuration i2c for ddc could change,
this patch allow to use a phandle to specify which i2c controller to use.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Here are the PCI changes intended for v3.19. I don't think there's
anything very exciting here, but there was a lot of MSI-related stuff
coming via Thomas.
Details:
NUMA
- Allow numa_node override via sysfs (Prarit Bhargava)
Resource management
- Restore detection of read-only BARs (Myron Stowe)
- Shrink decoding-disabled window while sizing BARs (Myron Stowe)
- Add informational printk for invalid BARs (Myron Stowe)
- Remove fixed parameter in pci_iov_resource_bar() (Myron Stowe)
MSI
- Add pci_msi_ignore_mask to prevent writes to MSI/MSI-X Mask Bits (Yijing Wang)
- Revert "PCI: Add x86_msi.msi_mask_irq() and msix_mask_irq()" (Yijing Wang)
- s390/MSI: Use __msi_mask_irq() instead of default_msi_mask_irq() (Yijing Wang)
Virtualization
- xen: Process failure for pcifront_(re)scan_root() (Chen Gang)
- Make FLR and AF FLR reset warning messages different (Gavin Shan)
Generic host bridge driver
- Allocate config space windows after limiting bus number range (Lorenzo Pieralisi)
- Convert to DT resource parsing API (Lorenzo Pieralisi)
Freescale Layerscape
- Add Freescale Layerscape PCIe driver (Minghuan Lian)
NVIDIA Tegra
- Do not build on 64-bit ARM (Thierry Reding)
- Add Kconfig help text (Thierry Reding)
Renesas R-Car
- Make rcar_pci static (Jingoo Han)
Samsung Exynos
- Add exynos prefix to add_pcie_port(), pcie_init() (Jingoo Han)
ST Microelectronics SPEAr13xx
- Add spear prefix to add_pcie_port(), pcie_init() (Jingoo Han)
- Make spear13xx_add_pcie_port() __init (Jingoo Han)
- Remove unnecessary OOM message (Jingoo Han)
TI DRA7xx
- Add dra7xx prefix to add_pcie_port() (Jingoo Han)
- Make dra7xx_add_pcie_port() __init (Jingoo Han)
TI Keystone
- Make ks_dw_pcie_msi_domain_ops static (Jingoo Han)
- Remove unnecessary OOM message (Jingoo Han)
Miscellaneous
- Delete unnecessary NULL pointer checks (Markus Elfring)
- Remove unused to_hotplug_slot() (Gavin Shan)
- Whitespace cleanup (Jingoo Han)
- Simplify if-return sequences (Quentin Lambert)"
* tag 'pci-v3.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (28 commits)
PCI: Remove fixed parameter in pci_iov_resource_bar()
PCI: Add informational printk for invalid BARs
PCI: tegra: Add Kconfig help text
PCI: tegra: Do not build on 64-bit ARM
PCI: spear: Remove unnecessary OOM message
PCI: mvebu: Add a blank line after declarations
PCI: designware: Add a blank line after declarations
PCI: exynos: Remove unnecessary return statement
PCI: imx6: Use tabs for indentation
PCI: keystone: Remove unnecessary OOM message
PCI: Remove unused and broken to_hotplug_slot()
PCI: Make FLR and AF FLR reset warning messages different
PCI: dra7xx: Add __init annotation to dra7xx_add_pcie_port()
PCI: spear: Add __init annotation to spear13xx_add_pcie_port()
PCI: spear: Rename add_pcie_port(), pcie_init() to spear13xx_add_pcie_port(), etc.
PCI: dra7xx: Rename add_pcie_port() to dra7xx_add_pcie_port()
PCI: layerscape: Add Freescale Layerscape PCIe driver
PCI: Simplify if-return sequences
PCI: Delete unnecessary NULL pointer checks
PCI: Shrink decoding-disabled window while sizing BARs
...
|
|
thinkpad-acpi:
acpi: Remove _OSI(Linux) for ThinkPads
thinkpad-acpi: Try to use full software mute control
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
Before phy device link up, we only enable FEC mdio interrupt, which
is more reasonable.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For i.MX6SX FEC controller, there have interrupt mask and event
field extension. To support all SOCs FEC, we clear all interrupt
events during MAVC initial process.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some i.MX6 serial boards, phy power and refrence clock are supplied
or controlled by SOC. When do suspend/resume test, the power and clock
are disabled, so phy device link down.
For current driver, fep->link is still up status, which cause extra operation
like below code. To avoid the dumy operation, we set fep->link to down when
phy device is real down.
...
if (fep->link) {
napi_disable(&fep->napi);
netif_tx_lock_bh(ndev);
fec_stop(ndev);
netif_tx_unlock_bh(ndev);
napi_enable(&fep->napi);
fep->link = phy_dev->link;
status_change = 1;
}
...
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"There was a lot of clean ups and minor fixes. One of those clean ups
was to the trace_seq code. It also removed the return values to the
trace_seq_*() functions and use trace_seq_has_overflowed() to see if
the buffer filled up or not. This is similar to work being done to
the seq_file code as well in another tree.
Some of the other goodies include:
- Added some "!" (NOT) logic to the tracing filter.
- Fixed the frame pointer logic to the x86_64 mcount trampolines
- Added the logic for dynamic trampolines on !CONFIG_PREEMPT systems.
That is, the ftrace trampoline can be dynamically allocated and be
called directly by functions that only have a single hook to them"
* tag 'trace-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (55 commits)
tracing: Truncated output is better than nothing
tracing: Add additional marks to signal very large time deltas
Documentation: describe trace_buf_size parameter more accurately
tracing: Allow NOT to filter AND and OR clauses
tracing: Add NOT to filtering logic
ftrace/fgraph/x86: Have prepare_ftrace_return() take ip as first parameter
ftrace/x86: Get rid of ftrace_caller_setup
ftrace/x86: Have save_mcount_regs macro also save stack frames if needed
ftrace/x86: Add macro MCOUNT_REG_SIZE for amount of stack used to save mcount regs
ftrace/x86: Simplify save_mcount_regs on getting RIP
ftrace/x86: Have save_mcount_regs store RIP in %rdi for first parameter
ftrace/x86: Rename MCOUNT_SAVE_FRAME and add more detailed comments
ftrace/x86: Move MCOUNT_SAVE_FRAME out of header file
ftrace/x86: Have static tracing also use ftrace_caller_setup
ftrace/x86: Have static function tracing always test for function graph
kprobes: Add IPMODIFY flag to kprobe_ftrace_ops
ftrace, kprobes: Support IPMODIFY flag to find IP modify conflict
kprobes/ftrace: Recover original IP if pre_handler doesn't change it
tracing/trivial: Fix typos and make an int into a bool
tracing: Deletion of an unnecessary check before iput()
...
|
|
Merge first patchbomb from Andrew Morton:
- a few minor cifs fixes
- dma-debug upadtes
- ocfs2
- slab
- about half of MM
- procfs
- kernel/exit.c
- panic.c tweaks
- printk upates
- lib/ updates
- checkpatch updates
- fs/binfmt updates
- the drivers/rtc tree
- nilfs
- kmod fixes
- more kernel/exit.c
- various other misc tweaks and fixes
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (190 commits)
exit: pidns: fix/update the comments in zap_pid_ns_processes()
exit: pidns: alloc_pid() leaks pid_namespace if child_reaper is exiting
exit: exit_notify: re-use "dead" list to autoreap current
exit: reparent: call forget_original_parent() under tasklist_lock
exit: reparent: avoid find_new_reaper() if no children
exit: reparent: introduce find_alive_thread()
exit: reparent: introduce find_child_reaper()
exit: reparent: document the ->has_child_subreaper checks
exit: reparent: s/while_each_thread/for_each_thread/ in find_new_reaper()
exit: reparent: fix the cross-namespace PR_SET_CHILD_SUBREAPER reparenting
exit: reparent: fix the dead-parent PR_SET_CHILD_SUBREAPER reparenting
exit: proc: don't try to flush /proc/tgid/task/tgid
exit: release_task: fix the comment about group leader accounting
exit: wait: drop tasklist_lock before psig->c* accounting
exit: wait: don't use zombie->real_parent
exit: wait: cleanup the ptrace_reparented() checks
usermodehelper: kill the kmod_thread_locker logic
usermodehelper: don't use CLONE_VFORK for ____call_usermodehelper()
fs/hfs/catalog.c: fix comparison bug in hfs_cat_keycmp
nilfs2: fix the nilfs_iget() vs. nilfs_new_inode() races
...
|
|
rtc_timer_do_work() only judges -ETIME failure of__rtc_set_alarm(), but
doesn't handle other failures like -EIO, -EBUSY, etc.
If there is a failure other than -ETIME, the next rtc_timer will stay in
the timerqueue. Then later rtc_timers will be enqueued directly because
they have a later expires time, so the alarm irq will never be programmed.
When such failures happen, this patch will retry __rtc_set_alarm(), if
still can't program the alarm time, it will remove current rtc_timer from
timerqueue and fetch next one, thus preventing it from affecting other rtc
timers.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, ab8500 doesn't set uie_unsupported of rtc_device, while it
doesn't support UIE, see ab8500_rtc_set_alarm().
Thus, when going through rtc_update_irq_enable()->rtc_timer_enqueue(),
there's a chance it has an alarm timer1 queued before which is going to
fired, so this update timer2 will be queued because it isn't the leftmost
one, which means rtc_timer_enqueue() will return 0.
This will result in two problems:
1) UIE EMUL will not be used.
2) When the alarm timer1 is fired, in rtc_timer_do_work() timer2 will
fail to set the alarm time, so this rtc will disfunctional due to
timer2 with the earliest expires in the timerqueue.
So, rtc drivers must set this flag if they don't support UIE.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The alarm interrupt handler also reads registers which are part of SNVS
and need clocks enabled. However, the resume function is called after
IRQ's have been enabled, hence this leads to a abort:
Unhandled fault: external abort on non-linefetch (0x1008) at 0x908c604c
Internal error: : 1008 [#1] ARM
Modules linked in:
CPU: 0 PID: 421 Comm: sh Not tainted 3.18.0-rc5-00135-g0689c67-dirty #1592
task: 8e03e800 ti: 8cad8000 task.ti: 8cad8000
PC is at snvs_rtc_irq_handler+0x14/0x74
LR is at handle_irq_event_percpu+0x3c/0x144
Fix this by using the .{suspend/resume}_noirq callbacks instead of
.{suspend/resume} .
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add clock enable and disable support for the SNVS peripheral, which is
required for using the RTC within the SNVS block.
The clock is not strictly enforced, as this would break the i.MX devices.
The clocking for the i.MX devices seems to be enabled elsewhere and
enabling RTC SNVS for Vybrid results in a crash. This patch adds the
clock support but also makes it optional so Vybrid platform can use the
clock if defined while making sure not to break i.MX.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stefan Agner <stefan@agner.ch>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Drop the vendor-prefix from the "ti,system-power-controller" device-tree
property name.
It has been agreed to make "system-power-controller" a standard property
and to drop the vendor-prefix that is currently used by several drivers.
Note that drivers that have used "<vendor>,system-power-controller" in a
released kernel will need to support both versions.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benot Cousson <bcousson@baylibre.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As pointed out by Mark, it is generally useful to log the error code when
reporting a failure. This patch improves existing calls to dev_err() in
ISL12057 driver to also report error code.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Suggested-by: Mark Brown <broonie@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grant Likely <grant.likely@linaro.org>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As suggested by Uwe, instead of clearing oscillator failure bit
unconditionally at driver load, this patch adds proper handling of the
flag. The driver now returns -ENODATA when reading time from the device
and oscillator failure bit is set. The flag is now cleared only when the
a new time value is pushed to the device.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Reported-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The month register of ISL12057 RTC chip includes a century bit which
reports overflow of year register from 99 to 0. This bit can also be
written, which allows using it to extend the time interval the chip can
support from 99 to 199 years.
This patch adds support for century overflow bit in tm to regs and regs to
tm helpers in ISL12057 driver.
This was tested by putting a device 100 years in the future (using a
specific kernel due to the inability of userland tools such as date or
hwclock to pass year 2038), rebooting on a kernel w/ this patch applied
and verifying the device was still 100 years in the future.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Suggested-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When Intersil ISL12057 support was added by commit 70e123373c05 ("rtc: Add
support for Intersil ISL12057 I2C RTC chip"), two masks for time registers
values imported from the device were either wrong or omitted, leading to
additional bits from those registers to impact read values:
- mask for hour register value when reading it in AM/PM mode. As
AM/PM mode is not the usual mode used by the driver, this error
would only have an impact on an externally configured RTC hour
later read by the driver.
- mask for month value. The lack of masking would provide an
erroneous value if century bit is set.
This patch fixes those two masks.
Fixes: 70e123373c05 ("rtc: Add support for Intersil ISL12057 I2C RTC chip")
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
MCP7940x is same RTC as MCP7941x. The difference is that MCP7941x chips
contain additional EEPROM on a different i2c address.
DS1307 driver already supports MCP7941x, so just add a new i2c device id
and rename functions and defines accordingly.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add support for the watchdog functionality of the DS1374 rtc. Based on
the m41t80 watchdog functionality Note: watchdog uses the same registers
as alarm.
[akpm@linux-foundation.org: don't forget mutex_unlock() in ds1374_wdt_open() error path]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Soeren Andersen <san@rosetechnology.dk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|