| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Supports YCbCr420sp, YCbCr422sp, and YCbCr44sp, formats
(bpp = 12, 16, and 24) respectively.
When double-buffering both Y planes appear before the C planes (Y-Y-C-C),
as opposed to Y-C-Y-C.
Set .nonstd in struct sh_mobile_lcdc_chan_cfg to enable YUV mode, and use
.bpp to distiguish between the 3 modes.
The value of .nonstd is copied to bits 16-31 of LDDFR in the LCDC and
should be set accordingly.
.nonstd must be set to 0 for RGB mode.
Due to the encoding of YUV data, the framebuffer will clear to green
instead of black.
In YUV 420 mode, panning is only possible in 2 line increments.
Additionally in YUV 420 mode the vertical resolution of the framebuffer
must be an even number.
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
This patch splits the pll configs up on pll versions. This allows
easy adding of other known good pll values. Additionally it made it
possible to remove invalid configurations resulting in better
behaviour for such cases. The resulting clocks are no longer stored
resulting in some computing overhead on each mode change.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
The clocks can be easily recalculated by the timing and refresh value.
This brings us one step closer to removing VIAs modetable and use
generic ones and being easier extensible.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Before this patch only clocks that perfectly match were used and if
none existed this was not handled properly. This patch changes this
to always use the closest clock supported. This should behave like
before for clocks that have a perfect match but be much saner for
clocks which are slightly off.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
This patch removes the direct lookup table for resolution+refresh and
pixclock by calculating this information from the mode table. Removes a
lot of dupllication and error potential by just doing a little more
calculations on each mode change.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Support for backlight devices controlled through board-specific
routines. Backlights can be defined per-channel and follow fbdev
directives to switch off as the LCD blanks or is turned on/off.
Signed-off-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
watchdog: sbc_fitpc2_wdt, fix crash on systems without DMI_BOARD_NAME
|
|
* 'for-2639-rc7/i2c-fixes' of git://git.fluff.org/bjdooks/linux:
i2c-eg20t: include slab.h for memory allocations
i2c-ocores: Fix pointer type mismatch error
i2c-omap: Program I2C_WE on OMAP4 to enable i2c wakeup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: fix CONFIG_MMC_UNSAFE_RESUME regression
|
|
Some systems don't provide DMI_BOARD_NAME in their DMI tables. Avoid
crash in such situations in fitpc2_wdt_init.
The fix is to check if the dmi_get_system_info return value is NULL.
The oops:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81253ae6>] strstr+0x26/0xa0
PGD 3966e067 PUD 39605067 PMD 0
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/system/cpu/cpu1/cache/index2/shared_cpu_map
CPU 1
Modules linked in: ...
Pid: 1748, comm: modprobe Not tainted 2.6.37-22-default #1 /Bochs
RIP: 0010:[<ffffffff81253ae6>] [<ffffffff81253ae6>] strstr+0x26/0xa0
RSP: 0018:ffff88003ad73f18 EFLAGS: 00010206
RAX: 0000000000000000 RBX: 00000000ffffffed RCX: 00000000ffffffff
RDX: ffffffffa003f4cc RSI: ffffffffa003f4c2 RDI: 0000000000000000
...
CR2: 0000000000000000 CR3: 000000003b7ac000 CR4: 00000000000006e0
...
Process modprobe (pid: 1748, threadinfo ffff88003ad72000, task ffff88002e6365c0)
Stack: ...
Call Trace:
[<ffffffffa004201f>] fitpc2_wdt_init+0x1f/0x13c [sbc_fitpc2_wdt]
[<ffffffff810002da>] do_one_initcall+0x3a/0x170
...
Code: f3 c3 0f 1f 00 80 3e 00 53 48 89 f8 74 1b 48 89 f2 0f 1f 40 00 48 83 c2 01 80 3a 00 75 f7 49 89 d0 48 89 f8 49 29 f0 75 02 5b c3 <80> 3f 00 74 0e 0f 1f 44 00 00 48 83 c0 01 80 38 00 75 f7 49 89
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
These parameters are the same for all currently known VIA IGPs so it
does not make any sense to store them with IGP specific data. This
saves a few bytes and helps a bit in dicovering the real differences.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
This patch removes some write-only variables from the device management
structures. Just a small cleanup.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
This patch is a little cleanup for the chip_info structures.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
This patch removes all internal uses of another mostly artificial
value. It does duplicate the information of the maximum resolution and
it is not flexible as only a few resolutions exist. Hence it is better
to remove it and clean the mess up.
No runtime change expected.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Many local variables should be declared static.
Found by sparse, compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
This driver is not respecting the iomem memory space restrictions
and does direct access. This works on x86 but is non-portable and
should not be done. Converted memcpy() of 2 to readw.
Last post increment of romptr was unnecessary since pointer never
used after that.
Found by sparse, compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Fixes (with v2.6.38-rc3/parisc/parisc-allmodconfig):
src/drivers/i2c/busses/i2c-eg20t.c:720: error: implicit declaration of function 'kzalloc'
src/drivers/i2c/busses/i2c-eg20t.c:790: error: implicit declaration of function 'kfree'
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
ocores_i2c_of_probe needs to use a const __be32 type for handing
device tree property values. This patch fixed the following build
warning:
CC drivers/i2c/busses/i2c-ocores.o
drivers/i2c/busses/i2c-ocores.c: In function 'ocores_i2c_of_probe':
drivers/i2c/busses/i2c-ocores.c:254: warning: assignment discards qualifiers from pointer target type
drivers/i2c/busses/i2c-ocores.c:261: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
30201e7f3 ("mmc: skip detection of nonremovable cards on rescan")
allowed skipping detection of nonremovable cards on mmc_rescan().
The intention was to only skip detection of hardwired cards that
cannot be removed, so make sure this is indeed the case by directly
checking for (lack of) MMC_CAP_NONREMOVABLE, instead of using
mmc_card_is_removable(), which is overloaded with
CONFIG_MMC_UNSAFE_RESUME semantics.
The user-visible symptom of the bug this patch fixes is that no
"mmc: card XXXX removed" message appears in dmesg when a card is
removed and CONFIG_MMC_UNSAFE_RESUME=y.
Reported-and-tested-by: Dmitry Shmidt <dimitrysh@google.com>
Reported-and-tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
davinci: cpufreq: fix section mismatch warning
DaVinci: fix compilation warnings in <mach/clkdev.h>
davinci: tnetv107x: fix register indexing for GPIOs numbers > 31
davinci: da8xx/omap-l1x: add platform device for davinci-pcm-audio
ARM: pxa/tosa: register wm9712 codec device
ARM: pxa: enable pxa-pcm-audio on pxa210/pxa25x platform
ARM: pxa/colibri: don't register pxa2xx-pcmcia nodes on non-colibri platforms
ARM: pxa/tosa: drop setting LED trigger name, as it's unsupported now
ARM: 6762/1: Update number of VIC for S5P6442 and S5PC100
ARM: 6761/1: Update number of VIC for S5PV210
ARM: 6768/1: hw_breakpoint: ensure debug logic is powered up on v7 cores
ARM: 6767/1: ptrace: fix register indexing in GETHBPREGS request
ARM: 6765/1: remove obsolete comment from asm/mach/arch.h
ARM: 6757/1: fix tlb.h induced linux/swap.h build failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: sdio: Allow sdio operations in other threads during sdio_add_func()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: index i shadowed in 2nd loop
drm/nv50-nvc0: prevent multiple vm/bar flushes occuring simultanenously
drm/nouveau: fix regression causing ttm to not be able to evict vram
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
|
|
Index i was already used in thhe first loop
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This fixes a bug introduced by 807e8e40673d ("mmc: Fix sd/sdio/mmc
initialization frequency retries") that prevented SDIO drivers from
performing SDIO commands in their probe routines -- the above patch
called mmc_claim_host() before sdio_add_func(), which causes a deadlock
if an external SDIO driver calls sdio_claim_host().
Fix tested on an OLPC XO-1.75 with libertas on SDIO.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Reviewed-and-Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
* ickle/drm-intel-fixes:
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] tape: deadlock on system work queue
[S390] keyboard: integer underflow bug
[S390] xpram: remove __initdata attribute from module parameters
|
|
The per-vm mutex doesn't prevent this completely, a flush coming from the
BAR VM could potentially happen at the same time as one for the channel
VM. Not to mention that if/when we get per-client/channel VM, this will
happen far more frequently.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
TTM assumes an error condition from man->func->get_node() means that
something went horribly wrong, and causes it to bail.
The driver is supposed to return 0, and leave mm_node == NULL to
signal that it couldn't allocate any memory.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Early gen3 and gen2 chipset do not have the relaxed per-surface tiling
constraints of the later chipsets, so we need to check that the GTT
alignment is correct for the new tiling. If it is not, we need to
rebind.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Andi Kleen narrowed his GPU hangs on his Sugar Bay (SNB desktop) rev 09
down to the use of GPU semaphores, and we already know that they appear
broken up to Huron River (mobile) rev 08. (I'm optimistic that disabling
GPU semaphores is simply hiding another bug by the latency and
side-effects of the additional device interaction it introduces...)
However, use of semaphores is a massive performance improvement... Only
as long as the system remains stable. Enable at your peril.
Reported-by: Andi Kleen <andi-fd@firstfloor.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33921
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
For the I2C module to be wakeup capable, programming I2C_WE register (which
was skipped for OMAP4430) is needed even on OMAP4.
This fixes i2c controller timeouts which were seen recently with the static
dependency being cleared between MPU and L4PER clockdomains.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[ben-linux@fluff.org: re-flowed description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
If a virtio-console device gets unplugged while a port is open, a
subsequent close() call on the port accesses vqs to free up buffers.
This can lead to a crash.
The buffers are already freed up as a result of the call to
unplug_ports() from virtcons_remove(). The fix is to simply not access
vq information if port->portdev is NULL.
Reported-by: juzhang <juzhang@redhat.com>
CC: stable@kernel.org
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Whilst the GT is powered down (rc6), writes to MMADDR are placed in a
FIFO by the System Agent. This is a limited resource, only 64 entries, of
which 20 are reserved for Display and PCH writes, and so we must take
care not to queue up too many writes. To avoid this, there is counter
which we can poll to ensure there are sufficient free entries in the
fifo.
"Issuing a write to a full FIFO is not supported; at worst it could
result in corruption or a system hang."
Reported-and-Tested-by: Matt Turner <mattst88@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34056
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
This reverts commit c2e0eb167070a6e9dcb49c84c13c79a30d672431.
As it turns out, userspace already depends upon being able to enable
tiling on existing bo which it promises to be large enough for its
purposes i.e. it will not access beyond the end of the last full-tile
row.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35016
Reported-and-tested-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This driver causes hard lockups, when the active clock soure is jiffies.
The reason is that it loops with interrupts disabled waiting for a
timestamp to be reached by polling getnstimeofday(). Though with a
jiffies clocksource, when that code runs on the same CPU which is
responsible for updating jiffies, then we loop in circles for ever
simply because the timer interrupt cannot update jiffies. So both UP
and SMP can be affected.
There is no easy fix for that problem so make it depend on BROKEN for
now.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The device table is required to load modules based on modaliases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Shubhrajyoti D <shubhrajyoti@ti.com>
Cc: Christoph Mair <christoph.mair@gmail.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix s3c_rtc_setaie() prototype to eliminate the following compile
warning:
drivers/rtc/rtc-s3c.c:383: warning: initialization from incompatible pointer type
(akpm: the rtc_class_ops.alarm_irq_enable() handler is being passed two
arguments where it expects just one, presumably with undesired effects)
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The nv30/nv40 3d driver is about to start using DMA_FENCE from the 3D
object which, it turns out, doesn't like its DMA object to not be
aligned to a 4KiB boundary.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
MAINTAINERS: Add Andy Gospodarek as co-maintainer.
r8169: disable ASPM
RxRPC: Fix v1 keys
AF_RXRPC: Handle receiving ACKALL packets
cnic: Fix lost interrupt on bnx2x
cnic: Prevent status block race conditions with hardware
net: dcbnl: check correct ops in dcbnl_ieee_set()
e1000e: disable broken PHY wakeup for ICH10 LOMs, use MAC wakeup instead
igb: fix sparse warning
e1000: fix sparse warning
netfilter: nf_log: avoid oops in (un)bind with invalid nfproto values
dccp: fix oops on Reset after close
ipvs: fix dst_lock locking on dest update
davinci_emac: Add Carrier Link OK check in Davinci RX Handler
bnx2x: update driver version to 1.62.00-6
bnx2x: properly calculate lro_mss
bnx2x: perform statistics "action" before state transition.
bnx2x: properly configure coefficients for MinBW algorithm (NPAR mode).
bnx2x: Fix ethtool -t link test for MF (non-pmf) devices.
bnx2x: Fix nvram test for single port devices.
...
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: kill loop_mutex
blktrace: Remove blk_fill_rwbs_rq.
block: blk-flush shouldn't call directly into q->request_fn() __blk_run_queue()
block: add @force_kblockd to __blk_run_queue()
block: fix kernel-doc format for blkdev_issue_zeroout
blk-throttle: Do not use kblockd workqueue for throtl work
|
|
For some time is known that ASPM is causing troubles on r8169, i.e. make
device randomly stop working without any errors in dmesg.
Currently Tomi Leppikangas reports that system with r8169 device hangs
with MCE errors when ASPM is enabled:
https://bugzilla.redhat.com/show_bug.cgi?id=642861#c4
Lets disable ASPM for r8169 devices at all, to avoid problems with
r8169 PCIe devices at least for some users.
Reported-by: Tomi Leppikangas <tomi.leppikangas@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 34xx and 3590 tape driver uses the system work queue to defer work
from the interrupt function to process context, e.g. a medium sense
after an unsolicited interrupt. The tape commands started by the work
handler need to be asynchronous, otherwise a deadlock on the system
work queue can occur.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The "ct" variable should be an unsigned int. Both struct kbdiacrs
->kb_cnt and struct kbd_data ->accent_table_size are unsigned ints.
Making it signed causes a problem in KBDIACRUC because the user could
set the signed bit and cause a buffer overflow.
Cc: <stable@kernel.org>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The module parameter 'devs' and 'sizes' are marked as __initdata. The
memory for the parameters are freed after module_init completed. This
can lead to kernel crashes in param_free_charp. Remove the __initdata
attribute to fix the problem.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Following steps lead to deadlock in kernel:
dd if=/dev/zero of=img bs=512 count=1000
losetup -f img
mkfs.ext2 /dev/loop0
mount -t ext2 -o loop /dev/loop0 mnt
umount mnt/
Stacktrace:
[<c102ec04>] irq_exit+0x36/0x59
[<c101502c>] smp_apic_timer_interrupt+0x6b/0x75
[<c127f639>] apic_timer_interrupt+0x31/0x38
[<c101df88>] mutex_spin_on_owner+0x54/0x5b
[<fe2250e9>] lo_release+0x12/0x67 [loop]
[<c10c4eae>] __blkdev_put+0x7c/0x10c
[<c10a4da5>] fput+0xd5/0x1aa
[<fe2250cf>] loop_clr_fd+0x1a9/0x1b1 [loop]
[<fe225110>] lo_release+0x39/0x67 [loop]
[<c10c4eae>] __blkdev_put+0x7c/0x10c
[<c10a59d9>] deactivate_locked_super+0x17/0x36
[<c10b6f37>] sys_umount+0x27e/0x2a5
[<c10b6f69>] sys_oldumount+0xb/0xe
[<c1002897>] sysenter_do_call+0x12/0x26
[<ffffffff>] 0xffffffff
Regression since 2a48fc0ab24241755dc9, which introduced the private
loop_mutex as part of the BKL removal process.
As per [1], the mutex can be safely removed.
[1] http://www.gossamer-threads.com/lists/linux/kernel/1341930
Addresses: https://bugzilla.novell.com/show_bug.cgi?id=669394
Addresses: https://bugzilla.kernel.org/show_bug.cgi?id=29172
Signed-off-by: Petr Uzel <petr.uzel@suse.cz>
Cc: stable@kernel.org
Reviewed-by: Nikanth Karthikesan <knikanth@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: fix memory corruption with GM965 and >4GB RAM
|
|
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
of/promtree: allow DT device matching by fixing 'name' brokenness (v5)
x86: OLPC: have prom_early_alloc BUG rather than return NULL
of/flattree: Drop an uninteresting message to pr_debug level
of: Add missing of_address.h to xilinx ehci driver
|
