Age | Commit message (Collapse) | Author |
|
- core_tpg_pre_addlun()
returns always ERR_PTR() or the pointer, never NULL. The additional
check for NULL in core_dev_add_lun() is not required.
- core_tpg_pre_dellun()
returns always ERR_PTR() or the pointer, never NULL. The check for NULL
in core_dev_del_lun() is wrong. The third argument (int *) is never
used, remove it.
- core_dev_add_lun()
returns always NULL or the pointer, never ERR_PTR. The check for
IS_ERR() is not required.
(nab: Convert core_dev_add_lun() use err.h macros for failure
handling to be consistent with the rest of target_core_fabric_configfs.c
callers)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
It may happen that uasp will free the request in irq conntext, the
callchain:
uasp_cmd_release() -> transport_generic_free_cmd() -> core_dec_lacl_count()
where the last function enables the IRQ. Those irqs are re-disabled
later (due to the spin.*irq_restore) but in between we could get hurt.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The multiple calls to pr_debug() each with one letter results in a new
line. This patch merges the multiple requests into one call per line
so we don't have the multiple line cuts.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds a work-around for handling zero allocation length
control CDBs (type SCF_SCSI_CONTROL_SG_IO_CDB) that was causing an
OOPs with the following raw calls:
# sg_raw -v /dev/sdd 3 0 0 0 0 0
# sg_raw -v /dev/sdd 0x1a 0 1 0 0 0
This patch will follow existing zero-length handling for data I/O
and silently return with GOOD status. This addresses the zero length
issue, but the proper long-term resolution for handling arbitary
allocation lengths will be to refactor out data-phase handling in
individual CDB emulation logic within target_core_cdb.c
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
According to SPC-4, the sense key for commands that are failed with
INVALID FIELD IN PARAMETER LIST and INVALID FIELD IN CDB should be
ILLEGAL REQUEST (5h) rather than ABORTED COMMAND (Bh). Without this
patch, a tcm_loop LUN incorrectly gives:
# sg_raw -r 1 -v /dev/sda 3 1 0 0 ff 0
Sense Information:
Fixed format, current; Sense key: Aborted Command
Additional sense: Invalid field in cdb
Raw sense data (in hex):
70 00 0b 00 00 00 00 0a 00 00 00 00 24 00 00 00
00 00
While a real SCSI disk gives:
Sense Information:
Fixed format, current; Sense key: Illegal Request
Additional sense: Invalid field in cdb
Raw sense data (in hex):
70 00 05 00 00 00 00 18 00 00 00 00 24 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
with the main point being that the real disk gives a sense key of
ILLEGAL REQUEST (5h).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Doing alloc_page(GFP_KERNEL | __GFP_ZERO) to get pages used for data
buffers wastes a lot of CPU clearing pages that will be quickly be
overwritten by the actual data. However, for emulated control
commands such as INQUIRY and so on, the code does assume that the
buffer is zeroed.
To avoid this CPU overhead, skip the __GFP_ZERO for commands that are
actually moving data, ie cmds that have SCF_SCSI_DATA_SG_IO_CDB set.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Initiators that aren't the active reservation holder should be able to
do a PERSISTENT RESERVE IN command in all cases, so add it to the list
of allowed CDBs in core_scsi3_pr_seq_non_holder().
Signed-off-by: Marco Sanvido <marco@purestorage.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The comments quote the right parts of the spec:
* d) Establish a unit attention condition for the
* initiator port associated with every I_T nexus
* that lost its registration other than the I_T
* nexus on which the PERSISTENT RESERVE OUT command
* was received, with the additional sense code set
* to REGISTRATIONS PREEMPTED.
and
* e) Establish a unit attention condition for the initiator
* port associated with every I_T nexus that lost its
* persistent reservation and/or registration, with the
* additional sense code set to REGISTRATIONS PREEMPTED;
but the actual code accidentally uses ASCQ_2AH_RESERVATIONS_PREEMPTED
instead of ASCQ_2AH_REGISTRATIONS_PREEMPTED. Fix this.
Signed-off-by: Marco Sanvido <marco@purestorage.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
We never embedd the bio into a structure, so there is no need to allocate
64 bytes of headroom per bio.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
tg3: Fix single-vector MSI-X code
openvswitch: Fix multipart datapath dumps.
ipv6: fix per device IP snmp counters
inetpeer: initialize ->redirect_genid in inet_getpeer()
net: fix NULL-deref in WARN() in skb_gso_segment()
net: WARN if skb_checksum_help() is called on skb requiring segmentation
caif: Remove bad WARN_ON in caif_dev
caif: Fix typo in Vendor/Product-ID for CAIF modems
bnx2x: Disable AN KR work-around for BCM57810
bnx2x: Remove AutoGrEEEn for BCM84833
bnx2x: Remove 100Mb force speed for BCM84833
bnx2x: Fix PFC setting on BCM57840
bnx2x: Fix Super-Isolate mode for BCM84833
net: fix some sparse errors
net: kill duplicate included header
net: sh-eth: Fix build error by the value which is not defined
net: Use device model to get driver name in skb_gso_segment()
bridge: BH already disabled in br_fdb_cleanup()
net: move sock_update_memcg outside of CONFIG_INET
mwl8k: Fixing Sparse ENDIAN CHECK warning
...
|
|
release
|
|
ACPI 5.0 provides extensions to the EINJ mechanism to specify the
target for the error injection - by APICID for cpu related errors,
by address for memory related errors, and by segment/bus/device/function
for PCIe related errors. Also extensions for vendor specific error
injections.
Tested-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
|
|
|
|
Function split up, should have no functional change.
Provides entry point for physically hotplugged CPUs
to initialize and activate cpuidle.
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
CC: Shaohua Li <shaohua.li@intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
V2: Fix typo: pr->handle -> pr, here: acpi_processor_hotadd_init(pr)
This is a very small part taken from patches which afaik
are coming from Yunhong Jiang (for a Xen not a Linus repo?).
Cleanup only: no functional change.
Advantage (beside cleanup) is that other data of the pr (acpi_processor) struct
in the acpi_processor_hotadd_init() is needed later, for example a newly
introduced flag:
pr->flags.need_hotplug_init
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Jiang, Yunhong <yunhong.jiang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Kdump kernels leave MSI-X interrupts (as setup by the crashed kernel)
enabled. However, kdump only enables one CPU in the new environment,
thus causing tg3 to abort MSI-X setup. When the driver attempts to
enable INTA or MSI interrupt modes on a kdump kernel, interrupt
delivery fails.
This patch attempts to workaround the problem by forcing the driver
to enable a single MSI-X interrupt. In such a configuration, the
device's multivector interrupt mode must be disabled.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (53 commits)
ARM: mach-shmobile: specify CHCLR registers on SH7372
dma: shdma: fix runtime PM: clear channel buffers on reset
dma/imx-sdma: save irq flags when use spin_lock in sdma_tx_submit
dmaengine/ste_dma40: clear LNK on channel startup
dmaengine: intel_mid_dma: remove legacy pm interface
ASoC: mxs: correct 'direction' of device_prep_dma_cyclic
dmaengine: intel_mid_dma: error path fix
dmaengine: intel_mid_dma: locking and freeing fixes
mtd: gpmi-nand: move to dma_transfer_direction
mtd: fix compile error for gpmi-nand
mmc: mxs-mmc: fix the dma_transfer_direction migration
dmaengine: add DMA_TRANS_NONE to dma_transfer_direction
dma: mxs-dma: Don't use CLKGATE bits in CTRL0 to disable DMA channels
dma: mxs-dma: make mxs_dma_prep_slave_sg() multi user safe
dma: mxs-dma: Always leave mxs_dma_init() with the clock disabled.
dma: mxs-dma: fix a typo in comment
DMA: PL330: Remove pm_runtime_xxx calls from pl330 probe/remove
video i.MX IPU: Fix display connections
i.MX IPU DMA: Fix wrong burstsize settings
dmaengine/ste_dma40: allow fixed physical channel
...
Fix up conflicts in drivers/dma/{Kconfig,mxs-dma.c,pl330.c}
The conflicts looked pretty trivial, but I'll ask people to verify them.
|
|
due to broken suspend functionality.
Signed-off-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
BF54x on-chip ATAPI controller allows maximum 0x1fffe bytes to be transfered
in one ATAPI transfer. So, set the max sg_tablesize to 4.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Configure the FSL SATA controller to the preferred, enterprise mode.
Signed-off-by: Yutaka Ando <r46913@freescale.com>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This saves devices suspend/resume time.
Tested system suspend/resume with SATA IDE/AHCI mode 3 times.
Below is the time took for devices suspend/resume.
SATA mode vanilla-kernel patched-kernel
--------- --------------------- ---------------------
IDE suspend: 0.744 suspend: 0.432
(0.716, 0.768, 0.748) (0.440, 0.428, 0.428)
resume: 5.084 resume: 2.209
(5.100, 5.064, 5.088) (2.168, 2.232, 2.228)
AHCI: suspend: 0.725 suspend: 0.449
(0.740, 0.708, 0.728) (0.456, 0.448, 0.444)
resume: 2.556 resume: 1.896
(2.604, 2.492, 2.572) (1.932, 1.872, 1.884)
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The as3645a driver calls kzalloc(). Include slab.h.
Reported-by: Fredrik Lingvall <fredrik.lingvall@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The intent here was to test if the FE_HAS_LOCK was set. The current
test is equivalent to "if (status) { ..."
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Several control names used inconsistent capitalization or were inconsistent
in other ways. I also corrected a spelling mistake and fixed four strings
that were too long (>31 characters). Harmless, but the string is cut off when
it is returned with QUERYCTRL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add an override of read_status to intercept lock status. This allows
us to switch LEDs appropriately on and off with signal un/locked.
The second phase is to override sleep to properly turn off both.
This is a hackish way to achieve that.
Thanks to Mike Krufky for his help.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This means cut & paste from the former f. attach. But while at it write
to the right GPIO to turn on the right LED. Also turn the other two
off jsut for sure.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The start is common for both stk7070pd and novatd specific routine.
This is just a preparation for the next patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
To properly support the three LEDs which are on the stick, we need
a special handling in the ->frontend_attach function. Thus let's have
a separate ->frontend_attach instead of ifs in the common one.
The hadnling itself will be added in further patches.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The dib0700 needs a binary firmware file. This patch added the MODULE_FIRMWARE-macro.
Signed-off-by: Christoph Anton Mitterer <calestyo@scientia.net>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This small patch removes superfluous DTV_CMDs from dvb_frontend.c which were added in the initially when ISBD-T support was added.
They were there unnoticed even though compilers should have warning about those duplicates. Finally they did and now we can remove them.
Thanks to Dan Carpenter <dan.carpenter@oracle.com> for pointing that out.
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
queue_setup callback has been extended with struct v4l2_format *fmt
parameter in 2d86401c2c commit. This patch adds this parameter to
s5p-jpeg driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Rewrite a duplicated test to test the correct value
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E;
@@
(
* E
|| ... || E
|
* E
&& ... && E
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Rewrite a duplicated test to test the correct value
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E;
@@
(
* E
|| ... || E
|
* E
&& ... && E
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch fixes the mismatch between control IDs (CID) and controls
for hflip, vflip and rotate.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This driver does an unconditional read of io space during module init which
causes a bad dereference on ARM. It looks to me like this is an x86 only
drivers, so restrict it to only compile on x86.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Denis Turischev <denis@compulab.co.il>
|
|
|
|
On October 1 in 2011,
OKI SEMICONDUCTOR Co., Ltd. changed the company name in to LAPIS Semiconductor Co., Ltd.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
ML7831 is companion chip for Intel Atom E6xx series.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
This patch modified the setting value of
I2C Bus Transfer Rate Setting Counter regisrer.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
For EG20T and ML7213 IOH, the i2c controller numbers are fixed, using
fixed bus number will make it much easier for platform code to use
i2c_register_board_info() to register i2c devices.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Add initial DT support to retrieve the frequency using a
DT attribute instead of the pdata pointer if of_node exist.
Add documentation for omap i2c controller binding.
Based on original patches from Manju and Grant.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Reviewed-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
On OMAP4 OMAP_I2C_STAT_NACK is causing a timeout on the next access.
The isr cleans all flags in OMAP_I2C_CON_REG by setting OMAP_I2C_CON_STP
OMAP_I2C_CON_STP is also set in omap_i2c_xfer_msg on the last message.
According to the TI TSR the sequence for OMAP_I2C_STAT_NACK and
OMAP_I2C_STAT_AL are nearly the same.
Removing the OMAP_I2C_CON_STP part in the isr fix the problem.
Tested on OMAP4430 and OMAP3530 (here NACK was not a problem)
Fixes also booting on 2430sdp.
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Correct OMAP_I2C_SYSC_REG offset in omap4 register map.
Offset 0x20 is reserved and OMAP_I2C_SYSC_REG has 0x10 as offset.
Signed-off-by: Alexander Aring <a.aring@phytec.de>
[khilman@ti.com: minor changelog edits]
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/for-linus-fixes-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/balloon: Move the registration from device to subsystem.
|