| Age | Commit message (Collapse) | Author |
|---|
|
This makes it easier to have outputs without subdevs.
This needs more work. The way the outputs are configured should be identical
to how inputs are configured.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
vpif_capture relied on a 1-1 mapping of input and subdev. This is not
necessarily the case. Separate the two. So there is a list of subdevs
and a list of inputs. Each input refers to a subdev and has routing
information. An input does not have to have a subdev.
The initial input for each channel is set to the fist input.
Currently missing is support for associating multiple subdevs with
an input.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The cleanup sequence was incorrect and could cause a kernel oops.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The cleanup sequence was incorrect and could cause a kernel oops.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When device nodes are registered they must be ready for use
immediately, so make sure the subdevs are loaded first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When device nodes are registered they must be ready for use
immediately, so make sure the subdevs are loaded first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Routing information is a property of the input, not of the subdev.
One subdev may provide multiple inputs, each with its own routing
information.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Calling a subdev op that isn't implemented will just return -ENOIOCTLCMD
No need to have a flag for that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The output index does not belong to video_obj, it belongs to
channel_obj. Also rename to output_idx to be consistent with
the input_idx name used in vpif_capture.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
input_idx does not belong to video_obj. Move it where it belongs.
Also remove the bogus code in the open() function that suddenly
changes the input to 0 for no reason.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
for da850/omap-l138, there is no need to setup_input_channel_mode()
and set_clock(), to avoid adding dummy code in board file just returning
zero add a check in the driver itself to call the handler only if its
not NULL.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
drivers/media/platform/fsl-viu.c: In function 'vidioc_s_fbuf':
drivers/media/platform/fsl-viu.c:867:32: warning: initialization discards 'const' qualifier from pointer target type [enabled by default]
This is fall-out from this commit:
commit e6eb28c2207b9397d0ab56e238865a4ee95b7ef9
Author: Hans Verkuil <hans.verkuil@cisco.com>
[media] v4l2: make vidioc_s_fbuf const
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
pattern control
V4L2_CID_TEST_PATTERN is now a standard control.
This patch replaces the user defined control for test
pattern to make use of standard control V4L2_CID_TEST_PATTERN.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
driver specific menu
Add helper function v4l2_ctrl_new_std_menu_items(), which adds
a standard menu control, with driver specific menu.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
add V4L2_CID_TEST_PATTERN of type menu, which determines
the internal test pattern selected by the device.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
.get_frame_desc can be used by host interface driver to query
properties of captured frames, e.g. required memory buffer size.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The V4L2_PIX_FMT_S5C_YUYV_JPG image formats consists of 2 planes, the
first containing interleaved JPEG/YUYV data and the second containing
meta data describing the interleaving method.
The image data is transferred with MIPI-CSI "User Defined Byte-Based
Data 1" type and is captured to memory by FIMC DMA engine.
The meta data is transferred using MIPI-CSI2 "Embedded 8-bit non Image
Data" and it is captured in the MIPI-CSI slave device and copied to
the bridge provided buffer.
To make sure the size of allocated buffers is correct for the subdevs
configuration when VIDIOC_STREAMON ioctl is invoked, an additional
check is added at the video pipeline validation function.
Flag FMT_FLAGS_COMPRESSED indicates the buffer size must be retrieved
from a sensor subdev.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
MIPI-CSI has internal memory mapped buffers for the frame embedded
(non-image) data. There are two buffers, for even and odd frames which
need to be saved after an interrupt is raised. The packet data buffers
size is 4 KiB and there is no status register in the hardware where the
actual non-image data size can be read from. Hence the driver copies
whole packet data buffer into a buffer provided by the FIMC driver.
This will form a separate plane in the user buffer.
When FIMC DMA engine is stopped by the driver due the to user space
not keeping up with buffer de-queuing the MIPI-CSIS will still run,
however it must discard data which is not captured by FIMC. Which
frames are actually capture by MIPI-CSIS is determined by means of
the s_tx_buffer subdev callback. When it is not called after a single
embedded data frame has been captured and copied and before next
embedded data frame interrupt occurrs, subsequent embedded data frames
will be dropped.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
drivers/media/platform/s5p-fimc/fimc-m2m.c:561:2: warning: passing argument 2 of 'fimc_m2m_try_crop' discards 'const' qualifier from pointer target type [enabled by default]
drivers/media/platform/s5p-fimc/fimc-m2m.c:502:12: note: expected 'struct v4l2_crop *' but argument is of type 'const struct v4l2_crop *'
This is fall-out from this commit:
commit 4f996594ceaf6c3f9bc42b40c40b0f7f87b79c86
Author: Hans Verkuil <hans.verkuil@cisco.com>
[media] v4l2: make vidioc_s_crop const
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
drivers/media/platform/s5p-g2d/g2d.c:535:2: warning: passing argument 3 of 'vidioc_try_crop' discards 'const' qualifier from pointer target type [enabled by default]
drivers/media/platform/s5p-g2d/g2d.c:510:12: note: expected 'struct v4l2_crop *' but argument is of type 'const struct v4l2_crop *'
This is fall-out from this commit:
commit 4f996594ceaf6c3f9bc42b40c40b0f7f87b79c86
Author: Hans Verkuil <hans.verkuil@cisco.com>
[media] v4l2: make vidioc_s_crop const
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch adds a module-device-table-entry to the
technisat-usb2-driver which will help udev to on-demand load the
driver. This was obviously forgotten during initial commit.
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This should be register 66 instead of 62.
(probably happened by copy&past'ing from the lines below)
Signed-off-by: Daniel Golle <dgolle@allnet.de>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Using ieee80211_free_txskb for tx frames is required, since mac80211 clones
skbs for which socket tx status is requested.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Ensure that drv_start() always returns true, as a failing hw start usually
eventually leads to crashes when there's still a station entry present.
Call a power-on reset after a resume and after a hw reset failure to bring
the hardware back to life again.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath_pci_aspm_init is only called on card init, so PCI registers get reset
after a suspend/resume cycle.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix build failure in Intel PIIX4 I2C driver.
Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org [v3.6]
|
|
Now that i2c-mux-gpio is able to find the GPIO chip by itself, we can
delegate this task. The great thing here is that i2c-mux-gpio can
defer device probing until the gpio chip is available, so we no longer
depend on the module loading order.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The code instantiating an i2c-mux-gpio platform device doesn't
necessarily know in advance the GPIO pin numbers it wants to use. If
pins are on a GPIO device which gets its base GPIO number assigned
dynamically at run-time, the values can't be hard-coded.
In that case, let the caller tell i2c-mux-gpio the name of the GPIO
chip and the (relative) GPIO pin numbers to use. At probe time, the
i2c-mux-gpio driver will look for the chip and apply the proper offset
to turn relative GPIO pin numbers to absolute GPIO pin numbers.
The same could be (and was so far) done on the caller's end, however
doing it in i2c-mux-gpio has two benefits:
* It avoids duplicating the code on every caller's side (about 30
lines of code.)
* It allows for deferred probing for the muxed part of the I2C bus
only. If finding the GPIO chip is the caller's responsibility, then
deferred probing (if the GPIO chip isn't there yet) will not only
affect the mux and the I2C bus segments behind it, but also the I2C
bus trunk.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
|
|
Use the devm_kzalloc managed function to stripdown the error and remove
code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Add support for SMBus multiplexing on Asus Z8 motherboard series. On
these boards, the memory slots are behind a GPIO-controlled I2C
multiplexer. Models with 6 or 12 memory slots have 2 segments behind
the multiplexer, while models with 18 memory slots have 3 such
segments.
On these boards, only the memory slots are behind the multiplexer,
so it is possible to keep the autodetection mechanism.
The code is generic enough so it could work on other boards as long as
the multiplexer is controlled by GPIO pins. For other forms of
multiplexing (for example using an I2C device) additional code will be
needed.
Thanks to Asus for providing a board to develop and test this feature,
as well as all the technical information required.
At the moment, the GPIO driver must be loaded before the i2c-i801
driver, but I hope to solve this soon, using deferred probing on
the i2c-mux-gpio side.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The SMBus controller in the VIA VX900 appears to be compatible with
the VIA VX855, so just add the device ID.
This closes kernel bug #43096.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
i2c_parport_irq is only called internally so it can be static.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
i2c_dw_xfer_msg is only called internally so it can be static. It
original was, before the driver split. No idea why it was changed at
that time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Dirk Brandewie <dirk.brandewie@gmail.com>
|
|
Replace printks with pr_<level>s, add pr_fmt()s to replace NAMEs
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Reviewed-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Remove the global dependency of the I2C subsystem on HAS_IOMEM and
move the dependency to the i2c/busses submenu, with an exception for
i2c-stub.
The generic I2C part does not need to have HAS_IOMEM set and thus now
becomes available in UML, so the I2C subsystem can now be used, e.g.
by the i2c-stub driver, for development of I2C device drivers.
[JD: Some adjustments.]
[Heiko Carstens: Keep I2C disabled on S390.]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Converting kzalloc to devm_kzalloc simplifies the code and ensures that the
result, alert, is freed after the irq allocated by the subsequent
devm_request_irq. This in turn ensures that when an interrupt can be
triggered, the alert structure is still available.
The problem of a free after a devm_request_irq was found using the
following semantic match (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2,x,a,b,c,d;
identifier free;
position p1,p2;
@@
devm_request_irq@p1(e1,e2,...,x)
... when any
when != e2 = a
when != x = b
if (...) {
... when != e2 = c
when != x = d
free@p2(...,x,...);
...
return ...;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Let I2C bus segments behind multiplexers have a class. This allows for
device auto-detection on these segments. As long as parent segments
don't share the same class, it should be fine.
I implemented support in drivers i2c-mux-gpio and i2c-mux-pca954x. I
left i2c-mux-pca9541 and i2c-mux-pinctrl alone for the moment as I
don't know if this feature makes sense for the use cases of these
drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
Cc: Rodolfo Giometti <giometti@linux.it>
|
|
Make sure the duty-cycle and period passed in are not negative. This
should eventually be made implicit by making them unsigned. While at
it, the drivers' .config() implementations can have the equivalent
checks removed.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Axel Lin <axel.lin@gmail.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Jonghwan Choi <jhbird.choi@samsung.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: "Philip, Avinash" <avinashphilip@ti.com>
Cc: Vaibhav Bedia <vaibhav.bedia@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
|
|
This commit moves the driver to drivers/pwm and converts it to the new
PWM framework.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This commit moves the driver to drivers/pwm and converts it to the new
PWM framework.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Qin Rui <qinrui@mprc.pku.edu.cn>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
|
|
Managed versions of the pwm_get() and pwm_put() functions were recently
added to the PWM framework. They can be used to simplify cleanup in the
error paths and the device removal callback.
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc updates from Benjamin Herrenschmidt:
"Some highlights in addition to the usual batch of fixes:
- 64TB address space support for 64-bit processes by Aneesh Kumar
- Gavin Shan did a major cleanup & re-organization of our EEH support
code (IBM fancy PCI error handling & recovery infrastructure) which
paves the way for supporting different platform backends, along
with some rework of the PCIe code for the PowerNV platform in order
to remove home made resource allocations and instead use the
generic code (which is possible after some small improvements to it
done by Gavin).
- Uprobes support by Ananth N Mavinakayanahalli
- A pile of embedded updates from Freescale folks, including new SoC
and board supports, more KVM stuff including preparing for 64-bit
BookE KVM support, ePAPR 1.1 updates, etc..."
Fixup trivial conflicts in drivers/scsi/ipr.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc/iommu: Fix multiple issues with IOMMU pools code
powerpc: Fix VMX fix for memcpy case
driver/mtd:IFC NAND:Initialise internal SRAM before any write
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
powerpc: Remove tlb batching hack for nighthawk
powerpc: Set paca->data_offset = 0 for boot cpu
powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
powerpc/mpc85xx: Update interrupt handling for IFC controller
powerpc/85xx: Enable USB support in p1023rds_defconfig
powerpc/smp: Do not disable IPI interrupts during suspend
powerpc/eeh: Fix crash on converting OF node to edev
powerpc/eeh: Lock module while handling EEH event
powerpc/kprobe: Don't emulate store when kprobe stwu r1
powerpc/kprobe: Complete kprobe and migrate exception frame
powerpc/kprobe: Introduce a new thread flag
powerpc: Remove unused __get_user64() and __put_user64()
powerpc/eeh: Global mutex to protect PE tree
powerpc/eeh: Remove EEH PE for normal PCI hotplug
...
|
|
Pull networking changes from David Miller:
"The most important bit in here is the fix for input route caching from
Eric Dumazet, it's a shame we couldn't fully analyze this in time for
3.6 as it's a 3.6 regression introduced by the routing cache removal.
Anyways, will send quickly to -stable after you pull this in.
Other changes of note:
1) Fix lockdep splats in team and bonding, from Eric Dumazet.
2) IPV6 adds link local route even when there is no link local
address, from Nicolas Dichtel.
3) Fix ixgbe PTP implementation, from Jacob Keller.
4) Fix excessive stack usage in cxgb4 driver, from Vipul Pandya.
5) MAC length computed improperly in VLAN demux, from Antonio
Quartulli."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
ipv6: release reference of ip6_null_entry's dst entry in __ip6_del_rt
Remove noisy printks from llcp_sock_connect
tipc: prevent dropped connections due to rcvbuf overflow
silence some noisy printks in irda
team: set qdisc_tx_busylock to avoid LOCKDEP splat
bonding: set qdisc_tx_busylock to avoid LOCKDEP splat
sctp: check src addr when processing SACK to update transport state
sctp: fix a typo in prototype of __sctp_rcv_lookup()
ipv4: add a fib_type to fib_info
can: mpc5xxx_can: fix section type conflict
can: peak_pcmcia: fix error return code
can: peak_pci: fix error return code
cxgb4: Fix build error due to missing linux/vmalloc.h include.
bnx2x: fix ring size for 10G functions
cxgb4: Dynamically allocate memory in t4_memory_rw() and get_vpd_params()
ixgbe: add support for X540-AT1
ixgbe: fix poll loop for FDIRCTRL.INIT_DONE bit
ixgbe: fix PTP ethtool timestamping function
ixgbe: (PTP) Fix PPS interrupt code
ixgbe: Fix PTP X540 SDP alignment code for PPS signal
...
|
|
Merge misc patches from Andrew Morton:
"The MM tree is rather stuck while I wait to find out what the heck is
happening with sched/numa. Probably I'll need to route around all the
code which was added to -next, sigh.
So this is "everything else", or at least most of it - other small
bits are still awaiting resolutions of various kinds."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (180 commits)
lib/decompress.c add __init to decompress_method and data
kernel/resource.c: fix stack overflow in __reserve_region_with_split()
omfs: convert to use beXX_add_cpu()
taskstats: cgroupstats_user_cmd() may leak on error
aoe: update aoe-internal version number to 50
aoe: update documentation to better reflect aoe-plus-udev usage
aoe: remove unused code
aoe: make dynamic block minor numbers the default
aoe: update and specify AoE address guards and error messages
aoe: retain static block device numbers for backwards compatibility
aoe: support more AoE addresses with dynamic block device minor numbers
aoe: update documentation with new URL and VM settings reference
aoe: update copyright year in touched files
aoe: update internal version number to 49
aoe: remove unused code and add cosmetic improvements
aoe: increase net_device reference count while using it
aoe: associate frames with the AoE storage target
aoe: disallow unsupported AoE minor addresses
aoe: do revalidation steps in order
aoe: failover remote interface based on aoe_deadsecs parameter
...
|
|
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Ed Cashin <ecashin@coraid.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
