| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
serial: bcm63xx_uart: fix irq storm after rx fifo overrun.
amba pl011: platform data for reg lockup and glitch v2
amba pl011: workaround for uart registers lockup
tty: n_gsm: improper skb_pull() use was leaking framed data
tty: n_gsm: Fixed logic to decode break signal from modem status
TTY: ntty, add one more sanity check
TTY: ldisc, do not close until there are readers
8250: Fix capabilities when changing the port type
8250_pci: Fix missing const from merges
ARM: SAMSUNG: serial: Fix on handling of one clock source for UART
serial: ioremap warning fix for jsm driver.
8250_pci: add -ENODEV code for Intel EG20T PCH
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: comedi: fix build breakages on some platforms
Staging: brcm80211: disable drivers except for X86 or MIPS platforms
Staging: brcm80211: disable drivers for PPC platforms
Staging: iio: Make IIO depend on GENERIC_HARDIRQS
Staging: mei: fix suspend failure
Staging: fix iio builds when IIO_RING_BUFFER is not enabled
Staging: Comedi: Build only on arches providing PAGE_KERNEL_NOCACHE
Staging: fix more iio builds when IIO_RING_BUFFER is not enabled
|
|
* 'for-linus' of git://neil.brown.name/md:
md: avoid endless recovery loop when waiting for fail device to complete.
|
|
If a device fails in a way that causes pending request to take a while
to complete, md will not be able to immediately remove it from the
array in remove_and_add_spares.
It will then incorrectly look like a spare device and md will try to
recover it even though it is failed.
This leads to a recovery process starting and instantly aborting over
and over again.
We should check if the device is faulty before considering it to be a
spare. This will avoid trying to start a recovery that cannot
proceed.
This bug was introduced in 2.6.26 so that patch is suitable for any
kernel since then.
Cc: stable@kernel.org
Reported-by: Jim Paradis <james.paradis@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When auditing the locking in i915_gem.c (for a prospective change which
I then abandoned), I noticed two places where struct_mutex is not held
across GEM object manipulations that would usually require it.
Since one is in initial setup and the other in driver unload, I'm
guessing the mutex is not required for either; but post a patch in case
it is.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The interface to ->truncate_range is changing very slightly: once "tmpfs:
take control of its truncate_range" has been applied, this can be applied.
For now there is only a slight inefficiency while this remains unapplied,
but it will soon become essential for managing shmem's use of swap.
Change i915_gem_object_truncate() to use shmem_truncate_range() directly:
which should also spare i915 later change if we switch from
inode_operations->truncate_range to file_operations->fallocate.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Soon tmpfs will stop supporting ->readpage and read_cache_page_gfp(): once
"tmpfs: add shmem_read_mapping_page_gfp" has been applied, this patch can
be applied to ease the transition.
Make i915_gem_object_get_pages_gtt() use shmem_read_mapping_page_gfp() in
the one place it's needed; elsewhere use shmem_read_mapping_page(), with
the mapping's gfp_mask properly initialized.
Forget about __GFP_COLD: since tmpfs initializes its pages with memset,
asking for a cold page is counter-productive.
Include linux/shmem_fs.h also in drm_gem.c: with shmem_file_setup() now
declared there too, we shall remove the prototype from linux/mm.h later.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Soon tmpfs will stop supporting ->readpage and read_mapping_page(): once
"tmpfs: add shmem_read_mapping_page_gfp" has been applied, this patch can
be applied to ease the transition.
ttm_tt_swapin() and ttm_tt_swapout() use shmem_read_mapping_page() in
place of read_mapping_page(), since their swap_space has been created with
shmem_file_setup().
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Dave Airlie <airlied@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fis the warning
drivers/tty/serial/8250_pci.c:1457: warning: initialization from incompatible pointer type
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix this section mismatch:
WARNING: drivers/misc/ioc4.o(.data+0x144): Section mismatch in reference from the variable ioc4_load_modules_work to the function .devinit.text:ioc4_load_modules()
The variable ioc4_load_modules_work references
the function __devinit ioc4_load_modules()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
This one is potentially fatal; by the time ioc4_load_modules is invoked
it may already have been freed. For that reason ioc4_load_modules_work
can't be turned to __devinitdata but also because it's referenced in
ioc4_exit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Brent Casavant <bcasavan@sgi.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix this section mismatch:
WARNING: drivers/leds/leds-lp5523.o(.text+0x12f4): Section mismatch in reference from the function lp5523_probe() to the function .init.text:lp5523_init_led()
The function lp5523_probe() references
the function __init lp5523_init_led().
This is often because lp5523_probe lacks a __init
annotation or the annotation of lp5523_init_led is wrong.
Fixing this one triggers one more mismatch, fix that one as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix this section mismatch:
WARNING: drivers/leds/leds-lp5521.o(.text+0xf2c): Section mismatch in reference from the function lp5521_probe() to the function .init.text:lp5521_init_led()
The function lp5521_probe() references
the function __init lp5521_init_led().
This is often because lp5521_probe lacks a __init
annotation or the annotation of lp5521_init_led is wrong.
Fixing this mismatch triggers one more mismatch, fix that one as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
checking count
We observed the crash point count going negative in cases where the
crash point is hit multiple times before the check of "count == 0" is
done. Because of this we never call lkdtm_do_action(). This patch just
adds a spinlock to protect count.
Reported-by: Tapan Dhimant <tdhimant@akamai.com>
Signed-off-by: Josh Hunt <johunt@akamai.com>
Acked-by: Ankita Garg <ankita@in.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
PT7C4338 chip is being manufactured by Pericom Technology Inc. It is a
serial real-time clock which provides:
1) Low-power clock/calendar.
2) Programmable square-wave output.
It has 56 bytes of nonvolatile RAM. Its register set is same as that of
rtc device: DS1307.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: queue: bring discard_granularity/alignment into line with SCSI
mmc: queue: append partition subname to queue thread name
mmc: core: make erase timeout calculation allow for gated clock
mmc: block: switch card to User Data Area when removing the block driver
mmc: sdio: reset card during power_restore
mmc: cb710: fix #ifdef HAVE_EFFICIENT_UNALIGNED_ACCESS
mmc: sdhi: DMA slave ID 0 is invalid
mmc: tmio: fix regression in TMIO_MMC_WRPROTECT_DISABLE handling
mmc: omap_hsmmc: use original sg_len for dma_unmap_sg
mmc: omap_hsmmc: fix ocr mask usage
mmc: sdio: fix runtime PM path during driver removal
mmc: Add PCI fixup quirks for Ricoh 1180:e823 reader
mmc: sdhi: fix module unloading
mmc: of_mmc_spi: add NO_IRQ define to of_mmc_spi.c
mmc: vub300: fix null dereferences in error handling
|
|
Some platforms do not have virt_to_bus(), so properly depend on
CONFIG_VIRT_TO_BUS for the Comedi drivers that need this function.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
As David points out, the driver is also broken on SPARC, so might
as well just only enable it on platforms where people have reported it
working, instead of trying to list all of the ones where it doesn't
work, as the working platform list is much smaller...
Reported-by: David Miller <davem@davemloft.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Henry Ptasinski <henryp@broadcom.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Right now, bad things happen if you try to build these drivers for the
PPC platform as it seems that the code only has been tested and built on
the MIPS big endian platform.
So disable it on the PPC32 and PPC64 platforms for now, hopefully this
will be resolved in the future as I'm sure someone will want to use
these chips with that platform someday.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Henry Ptasinski <henryp@broadcom.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
On m68k (which doesn't support generic hardirqs yet):
drivers/staging/iio/industrialio-trigger.c: In function ‘iio_trigger_poll’:
drivers/staging/iio/industrialio-trigger.c:180: error: implicit declaration of function ‘generic_handle_irq’
drivers/staging/iio/industrialio-trigger.c: In function ‘iio_trigger_poll_chained’:
drivers/staging/iio/industrialio-trigger.c:200: error: implicit declaration of function ‘handle_nested_irq’
drivers/staging/iio/industrialio-trigger.c: In function ‘iio_trig_release’:
drivers/staging/iio/industrialio-trigger.c:379: error: implicit declaration of function ‘irq_modify_status’
drivers/staging/iio/industrialio-trigger.c:382: error: implicit declaration of function ‘irq_set_chip’
drivers/staging/iio/industrialio-trigger.c:384: error: implicit declaration of function ‘irq_set_handler’
drivers/staging/iio/industrialio-trigger.c:388: error: implicit declaration of function ‘irq_free_descs’
drivers/staging/iio/industrialio-trigger.c: In function ‘iio_trig_subirqmask’:
drivers/staging/iio/industrialio-trigger.c:402: error: implicit declaration of function ‘irq_data_get_irq_chip’
drivers/staging/iio/industrialio-trigger.c:402: warning: initialization makes pointer from integer without a cast
drivers/staging/iio/industrialio-trigger.c: In function ‘iio_trig_subirqunmask’:
drivers/staging/iio/industrialio-trigger.c:411: warning: initialization makes pointer from integer without a cast
drivers/staging/iio/industrialio-trigger.c: In function ‘iio_allocate_trigger’:
drivers/staging/iio/industrialio-trigger.c:432: error: implicit declaration of function ‘irq_alloc_descs’
drivers/staging/iio/industrialio-trigger.c:455: error: ‘handle_simple_irq’ undeclared (first use in this function)
drivers/staging/iio/industrialio-trigger.c:455: error: (Each undeclared identifier is reported only once
drivers/staging/iio/industrialio-trigger.c:455: error: for each function it appears in.)
Hence IIO_TRIGGER should depend on GENERIC_HARDIRQS.
But as IIO_TRIGGER and IIO_RING_BUFFER form a maze of dependencies and selects,
just make the whole IIO subsystem depend on GENERIC_HARDIRQS.
This dependency also covers !S390, so that one can be removed again.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
wait_event_interruptible_timeout return value was wrongly used.
The remaining timeout was used as the error code.
This fix translated wait_event_interruptible_timeout return value
into error code that can be propagated.
[10291.674121] pci_pm_suspend(): mei_pci_suspend+0x0/0x8b [mei] returns 2500
It's thinkpad t400 with
00:03.0 Communication controller [0780]: Intel Corporation Mobile 4 Series Chipset MEI Controller [8086:2a44] (rev 07)
Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix build by moving enum list outside of
#ifdef CONFIG_IIO_RING_BUFFER.
drivers/staging/iio/accel/adis16201_core.c:413: error: 'ADIS16201_SCAN_SUPPLY' undeclared here (not in a function)
drivers/staging/iio/accel/adis16201_core.c:417: error: 'ADIS16201_SCAN_TEMP' undeclared here (not in a function)
drivers/staging/iio/accel/adis16201_core.c:422: error: 'ADIS16201_SCAN_ACC_X' undeclared here (not in a function)
drivers/staging/iio/accel/adis16201_core.c:427: error: 'ADIS16201_SCAN_ACC_Y' undeclared here (not in a function)
drivers/staging/iio/accel/adis16201_core.c:432: error: 'ADIS16201_SCAN_AUX_ADC' undeclared here (not in a function)
drivers/staging/iio/accel/adis16201_core.c:436: error: 'ADIS16201_SCAN_INCLI_X' undeclared here (not in a function)
drivers/staging/iio/accel/adis16201_core.c:441: error: 'ADIS16201_SCAN_INCLI_Y' undeclared here (not in a function)
vers/staging/iio/accel/adis16203_core.c:374: error: 'ADIS16203_SCAN_SUPPLY' undeclared here (not in a function)
drivers/staging/iio/accel/adis16203_core.c:378: error: 'ADIS16203_SCAN_AUX_ADC' undeclared here (not in a function)
drivers/staging/iio/accel/adis16203_core.c:382: error: 'ADIS16203_SCAN_INCLI_X' undeclared here (not in a function)
drivers/staging/iio/accel/adis16203_core.c:388: error: 'ADIS16203_SCAN_INCLI_Y' undeclared here (not in a function)
drivers/staging/iio/accel/adis16203_core.c:392: error: 'ADIS16203_SCAN_TEMP' undeclared here (not in a function)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
On architectures that don't define PAGE_KERNEL_NOCACHE, the Comedi driver turns
into tragedy:
CC [M] drivers/staging/comedi/drivers.o
drivers/staging/comedi/drivers.c: In function ‘comedi_buf_alloc’:
drivers/staging/comedi/drivers.c:505:41: error: ‘PAGE_KERNEL_NOCACHE’ undeclared (first use in this function)
drivers/staging/comedi/drivers.c:505:41: note: each undeclared identifier is rep orted only once for each function it appears in
make[3]: *** [drivers/staging/comedi/drivers.o] Error 1
Restrict the driver to only those architectures that define PAGE_KERNEL_NOCACHE.
PAGE_KERNEL_NOCACHE is a kludge - some system architectures such as SGI IP27
are even uable to offer uncached operation - at least in the way an unwitting
driver might assume. I haven't looked in details how the driver is using
the area vmaped with PAGE_KERNEL_NOCACHE but maybe doing it XFS-style using
cached memory and the flush_kernel_vmap_range / invalidate_kernel_vmap_range
APIs in conjunction with the DMA API is a practical alternative.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: David Miller <davem@davemloft.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix lots more build errors in staging/iio when CONFIG_IIO_RING_BUFFER
is not enabled by moving enums and defines outside of the
CONFIG_IIO_RING_BUFFER ifdef block.
Examples (one from each driver; there were 116 total errors):
drivers/staging/iio/accel/adis16204_core.c:437: error: 'ADIS16204_SCAN_SUPPLY' undeclared here (not in a function)
drivers/staging/iio/accel/adis16209_core.c:410: error: 'ADIS16209_SCAN_SUPPLY' undeclared here (not in a function)
drivers/staging/iio/gyro/adis16260_core.c:420: error: 'ADIS16260_SCAN_GYRO' undeclared here (not in a function)
drivers/staging/iio/imu/adis16400_core.c:565: error: 'ADIS16400_SCAN_SUPPLY' undeclared here (not in a function)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hid-multitouch: add support for a new Lumio dual-touch panel
HID: hid-multitouch: correct VID for Stantum panels
HID: hid-multitouch: ensure slots are initialized
|
|
SCSI defines discard alignment as the offset to the first
optimal discard. In the case of SD/MMC, that is always zero
which is the default.
SCSI defines discard granularity as a hint of a optimal
discard size. That is much better expressed by the MMC
"preferred erase size" (pref_erase) field.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
For example, an eMMC with 2 boot partitions will have 3 threads.
The names change from:
40 ? 00:00:00 mmcqd/0
41 ? 00:00:00 mmcqd/0
42 ? 00:00:00 mmcqd/0
to:
40 ? 00:00:00 mmcqd/0
41 ? 00:00:00 mmcqd/0boot0
42 ? 00:00:00 mmcqd/0boot1
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The erase timeout calculation may depend on clock rate
which is zero if the clock is gated, so use
mmc_host_clk_rate() which allows for that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The MMC block driver and other drivers (e.g. mmc-test) will expect
the card to be switched to the User Data Area eMMC partition when
they start. Hence the MMC block driver should ensure it is that
way when it is removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
mmc_sdio_power_restore() skips some steps that are performed in other
power-related codepaths which are necessary to fully reset the card.
Without this, runtime PM fails for SD8686 SDIO wifi on OLPC XO-1.5.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
HAVE_EFFICIENT_UNALIGNED_ACCESS is a config option, therefore it needs
the CONFIG_ before it when used by the preprocessor.
Signed-off-by: James Hogan <james@albanarts.com>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Don't try to allocate DMA resources if the platform didn't specify
positive DMA slave IDs.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Commit b6147490e6aac82 ("mmc: tmio: split core functionality, DMA and
MFD glue") broke handling of the TMIO_MMC_WRPROTECT_DISABLE flag by
the tmio-mmc driver. This patch restores the original behaviour.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Don't use the returned sg_len from dma_map_sg() as inparameter
to dma_unmap_sg(). Use the original sg_len for both dma_map_sg
and dma_unmap_sg according to the documentation in DMA-API.txt.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The OMAP HSMMC driver uses an ocr_mask to determine the list of voltages
supported by the card. It populates this mask based on the list of
voltages supported by the regulator that supplies the voltage.
Commit 64be97822b (omap4 hsmmc: Update ocr mask for MMC2 for regulator
to use) passed a fixed ocr_mask from the OMAP4 SDP board file to limit
the voltage to 2.9-3.0 Volts, and updated the driver to use this mask
if provided, instead of using the regulator's supported voltages.
However the commit is buggy - the ocr_mask is overridden by the
regulator's capabilities anyway. Fix this.
(The bug shows up when a system-wide suspend is attempted on the OMAP4
SDP/Blaze platforms. The eMMC card comes up at 3V, but drops to 1.65V
after the system resumes).
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Balaji T K <balajitk@ti.com>
Acked-by: Venkatraman S <svenkatr@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
After commit e1866b3 "PM / Runtime: Rework runtime PM handling
during driver removal" was introduced, the driver core stopped
incrementing the runtime PM usage counter of the device during
the invocation of the ->remove() callback.
This indirectly broke SDIO's runtime PM path during driver removal,
because no one calls _put_sync() anymore after ->remove() completes.
This means that the power of runtime-PM-managed SDIO cards is kept
high after their driver is removed (even if it was powered down
beforehand).
Fix that by directly calling _put_sync() when the last usage
counter is downref'ed by the SDIO bus.
Reported-and-tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timer-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rtc: vt8500: Fix build error & cleanup rtc_class_ops->update_irq_enable()
alarmtimers: Return -ENOTSUPP if no RTC device is present
alarmtimers: Handle late rtc module loading
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915: save/resume forcewake lock fixes
Revert "drm/i915: Kill GTT mappings when moving from GTT domain"
drm/i915: Apply HWSTAM workaround for BSD ring on SandyBridge
drm/i915: Call intel_enable_plane from i9xx_crtc_mode_set (again)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_marvell: Add support for 88SE91A0, 88SE91A4
libata/sas: only set FROZEN flag if new EH is supported
libata: apply NOSETXFER horkage to the affected Pioneer drives regardless of firmware revision
drivers/ata/sata_dwc_460ex: Fix typo 'corrresponding'
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: handle special cases for vddc
drm/radeon/kms: fix num_banks tiling config for fusion
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/scsi-post-merge-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/scsi-post-merge-2.6:
tcm_fc: Fix conversion spec warning
tcm_fc: Fix possible lock to unlock type deadlock
tcm_fc: Fix ft_send_tm LUN lookup OOPs
target: Fix incorrect strlen() NULL terminator checks
target: Drop bogus ERR_PTR usage in target_fabric_configfs_init
target: Fix ERR_PTR dereferencing bugs
target: Convert transport_deregister_session_configfs nacl_sess_lock to save irq state
target: Fix transport_get_lun_for_tmr failure cases
[SCSI] target: Convert TASK_ATTR to scsi_tcq.h definitions
[SCSI] target: Convert REPORT_LUNs to use int_to_scsilun
[SCSI] target: Fix task->task_execute_queue=1 clear bug + LUN_RESET OOPs
[SCSI] target: Fix bug with task_sg chained transport_free_dev_tasks release
[SCSI] target: Fix interrupt context bug with stats_lock and core_tmr_alloc_req
[SCSI] target: Fix multi task->task_sg[] chaining logic bug
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
x86/PCI/ACPI: fix type mismatch
PCI: fix new kernel-doc warning
PCI: Fix warning in drivers/pci/probe.c on sparc64
|
|
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
while merging hid-stantum into hid-multitouch, I did not correctly copy/paste
the VIDs for those devices. This patch fixes it.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
In case a device does not provide the feature "Maximum Contact Count",
or set it at 0, the maxcontacts field may be at 0 while calling
input_mt_init_slots.
This patch ensures that hid-multitouch will allways report
ABS_MT_SLOT and ABS_MT_TRACKING_ID to the user space.
This corrects a bug found with some Ilitek devices that has been
integrated in 3.0-rc0.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch enables support for Marvell IDE PATA controllers found on
Asus P8P67LE motherboard.
The formatting has been corrected and I also received a report from two
users of this motherboard that the patch works.
Signed-off-by: Paweł Drewniak <czajernia@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
A voltage value of 0xff01 requires that the driver
look up the max voltage for the board based using the
atom SetVoltage command table.
Setting the proper voltage should fix stability on
some newer asics.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The field is encoded:
0 = 4 banks
1 = 8 banks
2 = 16 banks
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This patch fixes the following conversion specification warning for size_t
drivers/target/tcm_fc/tfc_io.c: In function ‘ft_queue_data_in’:
drivers/target/tcm_fc/tfc_io.c:209: warning: format ‘%x’ expects type ‘unsigned int’, but argument 5 has type ‘size_t’
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
There is a typo here, it should be an unlock instead of a lock. The
original code will deadlock.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes a bug in ft_send_tm() that was incorrectly calling
ft_get_lun_for_cmd() -> transport_get_lun_for_cmd(), instead of using
transport_get_lun_for_tmr() for the proper struct se_lun lookup
that was triggering an OOPs in the se_cmd->tmr_req failure path.
This patch fixes the issue by re-arranging the codepath where
transport_get_lun_for_tmr() is called after tmr request is allocated and
made it available as part of se_cmd.
It also drops the now unnecessary ft_get_lun_for_cmd() unpacking code, and
uses scsilun_to_int() directly ahead of transport_get_lun_for_cmd() and
transport_get_lun_for_tmr() usage.
Signed-off-by: Patil, Kiran <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
|
