| Age | Commit message (Collapse) | Author |
|---|
|
Wrong PCI device may be selected by cy82c693_set_pio_mode() if modular
IDE host drivers are used and there are additional IDE PCI devices
installed in the system. Fix it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix problem introduced by commit 5e37bdc ("ide: add struct
ide_dma_ops (take 3)"): d.dma_ops shouldn't be cleared if
we are going to use DMA.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't powerdown Compaq Triflex IDE device on suspend
This fixes APM suspend on Compaq Armada 7400.
APM BIOS doesn't suspend if IDE is powered down when suspending.
The Triflex controller is found only on old Compaq boards,
so this patch will hopefully have no side effects.
This patch fixes a suspend regression introduced in
feb22b7f8e62b1b987a3a1dbad95af767a1df832 ("ide: add proper PCI PM
support (v2)").
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
[bart: add commit's summary in parens]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on libata commit c611bed7.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: use hardcoded dig encoder to transmitter mapping for DCE4.1
drm/radeon/kms: fix dp_detect handling for DP bridge chips
drm/radeon/kms: retry aux transactions if there are status flags
|
|
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (29 commits)
MIPS: Call oops_enter, oops_exit in die
staging/octeon: Software should check the checksum of no tcp/udp packets
MIPS: Octeon: Enable C0_UserLocal probing.
MIPS: No branches in delay slots for huge pages in handle_tlbl
MIPS: Don't clobber CP0_STATUS value for CONFIG_MIPS_MT_SMTC
MIPS: Octeon: Select CONFIG_HOLES_IN_ZONE
MIPS: PM: Use struct syscore_ops instead of sysdevs for PM (v2)
MIPS: Compat: Use 32-bit wrapper for compat_sys_futex.
MIPS: Do not use EXTRA_CFLAGS
MIPS: Alchemy: DB1200: Disable cascade IRQ in handler
SERIAL: Lantiq: Set timeout in uart_port
MIPS: Lantiq: Fix setting the PCI bus speed on AR9
MIPS: Lantiq: Fix external interrupt sources
MIPS: tlbex: Fix build error in R3000 code.
MIPS: Alchemy: Include Au1100 in PM code.
MIPS: Alchemy: Fix typo in MAC0 registration
MIPS: MSP71xx: Fix build error.
MIPS: Handle __put_user() sleeping.
MIPS: Allow forced irq threading
MIPS: i8259: Mark cascade interrupt non-threaded
...
|
|
* git://github.com/davem330/net:
net: fix typos in Documentation/networking/scaling.txt
bridge: leave carrier on for empty bridge
netfilter: Use proper rwlock init function
tcp: properly update lost_cnt_hint during shifting
tcp: properly handle md5sig_pool references
macvlan/macvtap: Fix unicast between macvtap interfaces in bridge mode
|
|
* 'for-linus' of http://people.redhat.com/agk/git/linux-dm:
dm crypt: always disable discard_zeroes_data
dm: raid fix write_mostly arg validation
dm table: avoid crash if integrity profile changes
dm: flakey fix corrupt_bio_byte error path
|
|
* 'for-linus' of git://neil.brown.name/md:
md: Avoid waking up a thread after it has been freed.
|
|
The encoders are supposedly fully routeable, but changing the mapping
doesn't always seem to take. Using a hardcoded mapping is much more
reliable.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=41366
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
* 'for-linus' of git://github.com/dtor/input:
Input: wacom - revert "Cintiq 21UX2 does not have menu strips"
|
|
* git://bedivere.hansenpartnership.com/git/scsi-rc-fixes-2.6:
[SCSI] libsas: fix panic when single phy is disabled on a wide port
[SCSI] qla2xxx: Fix crash in qla2x00_abort_all_cmds() on unload
|
|
The HPD pin is not reliable for detecting whether a monitor
is connected or not. Skip HPD and just use DDC or load
detection.
Fixes phantom VGA connected bugs.
[Michel: fixes phantom VGA bugs on his llano system.]
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
If there are error flags in the aux status, retry the transaction.
This makes aux much more reliable, especially on llano systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This reverts commit 71c86ce59791bcd67af937bbea719a508079d7c2.
The 21UX2 does have touchstrips, but they are in a somewhat-
hidden location.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pinglinux@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Packets should always be forwarded to the lowerdev using dev_forward_skb.
vlan->forward is for packets being forwarded directly to another macvlan/
macvtap device (used for multicast in bridge mode).
Reported-and-tested-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://github.com/davem330/net:
pch_gbe: Fixed the issue on which a network freezes
pch_gbe: Fixed the issue on which PC was frozen when link was downed.
make PACKET_STATISTICS getsockopt report consistently between ring and non-ring
net: xen-netback: correctly restart Tx after a VM restore/migrate
bonding: properly stop queuing work when requested
can bcm: fix incomplete tx_setup fix
RDSRDMA: Fix cleanup of rds_iw_mr_pool
net: Documentation: Fix type of variables
ibmveth: Fix oops on request_irq failure
ipv6: nullify ipv6_ac_list and ipv6_fl_list when creating new socket
cxgb4: Fix EEH on IBM P7IOC
can bcm: fix tx_setup off-by-one errors
MAINTAINERS: tehuti: Alexander Indenbaum's address bounces
dp83640: reduce driver noise
ptp: fix L2 event message recognition
|
|
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: fix channel_remap setup (v2)
drm/radeon: Set cursor x/y to 0 when x/yorigin > 0.
drm/radeon: Update AVIVO cursor coordinate origin before x/yorigin calculation.
drm/radeon: Simplify cursor x/yorigin calculation.
drm/radeon/kms: fix cursor image off-by-one error
drm/radeon/kms: Fix logic error in DP HPD handler
drm/radeon/kms: add retry limits for native DP aux defer
drm/radeon/kms: fix regression in DP aux defer handling
|
|
* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
spi-topcliff-pch: Fix overrun issue
spi-topcliff-pch: Add recovery processing in case FIFO overrun error occurs
spi-topcliff-pch: Fix CPU read complete condition issue
spi-topcliff-pch: Fix SSN Control issue
spi-topcliff-pch: add tx-memory clear after complete transmitting
|
|
Add the ability to disable PCI-E MPS turning and using the BIOS
configured MPS defaults. Due to the number of issues recently
discovered on some x86 chipsets, make this the default behavior.
Also, add the option for peer to peer DMA MPS configuration. Peer to
peer DMA is outside the scope of this patch, but MPS configuration could
prevent it from working by having the MPS on one root port different
than the MPS on another. To work around this, simply make the system
wide MPS the smallest possible value (128B).
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Most asics just use the hw default value which requires
no explicit programming. For those that need a different
value, the vbios will program it properly. As such,
there's no need to program these registers explicitly
in the driver. Changing MC_SHARED_CHREMAP requires a reload
of all data in vram otherwise its contents will be scambled.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=40103
v2: drop now unused channel_remap functions.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
We found that adding load, Rx data sometimes drops.(with DMA transfer mode)
The cause is that before starting Rx-DMA processing, Tx-DMA processing starts.
This causes FIFO overrun occurs.
This patch fixes the issue by modifying FIFO tx-threshold and DMA descriptor
size like below.
Current this patch
Rx-descriptor 4Byte+12Byte*341 --> 12Byte*340-4Byte-12Byte
Rx-threshold (Not modified)
Tx-descriptor 4Byte+12Byte*341 --> 16Byte-12Byte*340
Rx-threshold 12Byte --> 2Byte
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Add recovery processing in case FIFO overrun error occurs with DMA transfer mode.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
We found Rx data sometimes drops.(with non-DMA transfer mode)
The cause is read complete condition is not true.
This patch fixes the issue.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
During processing 1 command/data series,
SSN should keep LOW.
However, currently, SSN becomes HIGH.
This patch fixes the issue.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Currently, in case of reading date from SPI flash,
command is sent twice.
The cause is that tx-memory clear processing is missing .
This patch adds the tx-momory clear processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Commit 2a7fade7e03 ("hwmon: lis3: Power on corrections") caused a
regression on HP laptops with 8bit chip. Writing CTRL2_BOOT_8B bit seems
clearing the BIOS setup, and no proper interrupt for DriveGuard will be
triggered any more.
Since the init code there is basically only for embedded devices, put a
pdata check so that the problematic initialization will be skipped for
hp_accel stuff.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'hwmon-for-linus' of git://github.com/groeck/linux:
hwmon: (coretemp) Avoid leaving around dangling pointer
hwmon: (coretemp) Fixup platform device ID change
|
|
Simon Kirby reported that on his RAID setup with idedisk underneath
the box OOMs after a couple of days of runtime. Running with
CONFIG_DEBUG_KMEMLEAK pointed to idedisk_prep_fn() which unconditionally
allocates an ide_cmd struct. However, ide_requeue_and_plug() can be
called more than once per request, either from the request issue or the
IRQ handler path and do blk_peek_request() ends up in idedisk_prep_fn()
repeatedly, allocating a struct ide_cmd everytime and "forgetting" the
previous pointer.
Make sure the code reuses the old allocated chunk.
Reported-and-tested-by: Simon Kirby <sim@hostway.ca>
Cc: <stable@kernel.org> [ 39.x, 3.0.x ]
Link: http://marc.info/?l=linux-kernel&m=131667641517919
Link: http://lkml.kernel.org/r/20110922072643.GA27232@hostway.ca
Signed-off-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pch_gbe driver has an issue which a network stops,
when receiving traffic is high.
In the case, The link down and up are necessary to return a network.
This patch fixed this issue.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a link was downed during network use,
there is an issue on which PC freezes.
This patch fixed this issue.
Signed-off-by: Toshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a VM is saved and restored (or migrated) the netback driver will no
longer process any Tx packets from the frontend. xenvif_up() does not
schedule the processing of any pending Tx requests from the front end
because the carrier is off. Without this initial kick the frontend
just adds Tx requests to the ring without raising an event (until the
ring is full).
This was caused by 47103041e91794acdbc6165da0ae288d844c820b (net:
xen-netback: convert to hw_features) which reordered the calls to
xenvif_up() and netif_carrier_on() in xenvif_connect().
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During a test where a pair of bonding interfaces using ARP monitoring
were both brought up and torn down (with an rmmod) repeatedly, a panic
in the timer code was noticed. I tracked this down and determined that
any of the bonding functions that ran as workqueue handlers and requeued
more work might not properly exit when the module was removed.
There was a flag protected by the bond lock called kill_timers that is
set when the interface goes down or the module is removed, but many of
the functions that monitor link status now unlock the bond lock to take
rtnl first. There is a chance that another CPU running the rmmod could
get the lock and set kill_timers after the first check has passed.
This patch does not allow any function to queue work that will make
itself run unless kill_timers is not set. I also noticed while doing
this work that bond_resend_igmp_join_requests did not have a check for
kill_timers, so I added the needed call there as well.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Reported-by: Liang Zheng <lzheng@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Apart from the obvious cleanup, this should make the line
cursor_end = x - xorigin + w;
correct now.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Fixes cursor disappearing prematurely when moving off a top/left edge which
is not located at the desktop top/left edge.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The mouse cursor hotspot calculation when the cursor is partially off the
top or left side of the screen was off by one.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=41158
Signed-off-by: Nicholas Miell <nmiell@gmail.com>
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Only disable the pipe if the monitor is physically
disconnected. The previous logic also disabled the
pipe if the link was trained.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=41248
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The previous code could potentially loop forever. Limit
the number of DP aux defer retries to 4 for native aux
transactions, same as i2c over aux transactions.
Noticed by: Brad Campbell <lists2009@fnarfbargle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Brad Campbell <lists2009@fnarfbargle.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
An incorrect ordering in the error checking code lead
to DP aux defer being skipped in the aux native write
path. Move the bytes transferred check (ret == 0)
below the defer check.
Tracked down by: Brad Campbell <brad@fnarfbargle.com>
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=41121
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Brad Campbell <brad@fnarfbargle.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
* 'for-linus' of git://git.infradead.org/users/sameo/mfd-2.6:
mfd: Fix generic irq chip ack function name for jz4740-adc
|
|
When a wide port is being utilized to a target, if one disables only one
of the
phys, we get an OS crash:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000238
IP: [<ffffffff814ca9b1>] mutex_lock+0x21/0x50
PGD 4103f5067 PUD 41dba9067 PMD 0
Oops: 0002 [#1] SMP
last sysfs file: /sys/bus/pci/slots/5/address
CPU 0
Modules linked in: pm8001(U) ses enclosure fuse nfsd exportfs autofs4
ipmi_devintf ipmi_si ipmi_msghandler nfs lockd fscache nfs_acl
auth_rpcgss 8021q fcoe libfcoe garp libfc scsi_transport_fc stp scsi_tgt
llc sunrpc cpufreq_ondemand acpi_cpufreq freq_table ipv6 sr_mod cdrom
dm_mirror dm_region_hash dm_log uinput sg i2c_i801 i2c_core iTCO_wdt
iTCO_vendor_support e1000e mlx4_ib ib_mad ib_core mlx4_en mlx4_core ext3
jbd mbcache sd_mod crc_t10dif usb_storage ata_generic pata_acpi ata_piix
libsas(U) scsi_transport_sas dm_mod [last unloaded: pm8001]
Modules linked in: pm8001(U) ses enclosure fuse nfsd exportfs autofs4
ipmi_devintf ipmi_si ipmi_msghandler nfs lockd fscache nfs_acl
auth_rpcgss 8021q fcoe libfcoe garp libfc scsi_transport_fc stp scsi_tgt
llc sunrpc cpufreq_ondemand acpi_cpufreq freq_table ipv6 sr_mod cdrom
dm_mirror dm_region_hash dm_log uinput sg i2c_i801 i2c_core iTCO_wdt
iTCO_vendor_support e1000e mlx4_ib ib_mad ib_core mlx4_en mlx4_core ext3
jbd mbcache sd_mod crc_t10dif usb_storage ata_generic pata_acpi ata_piix
libsas(U) scsi_transport_sas dm_mod [last unloaded: pm8001]
Pid: 5146, comm: scsi_wq_5 Not tainted
2.6.32-71.29.1.el6.lustre.7.x86_64 #1 Storage Server
RIP: 0010:[<ffffffff814ca9b1>] [<ffffffff814ca9b1>]
mutex_lock+0x21/0x50
RSP: 0018:ffff8803e4e33d30 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000238 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffff8803e664c800 RDI: 0000000000000238
RBP: ffff8803e4e33d40 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000000
R13: 0000000000000238 R14: ffff88041acb7200 R15: ffff88041c51ada0
FS: 0000000000000000(0000) GS:ffff880028200000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000238 CR3: 0000000410143000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process scsi_wq_5 (pid: 5146, threadinfo ffff8803e4e32000, task
ffff8803e4e294a0)
Stack:
ffff8803e664c800 0000000000000000 ffff8803e4e33d70 ffffffffa001f06e
<0> ffff8803e4e33d60 ffff88041c51ada0 ffff88041acb7200 ffff88041bc0aa00
<0> ffff8803e4e33d90 ffffffffa0032b6c 0000000000000014 ffff88041acb7200
Call Trace:
[<ffffffffa001f06e>] sas_port_delete_phy+0x2e/0xa0 [scsi_transport_sas]
[<ffffffffa0032b6c>] sas_unregister_devs_sas_addr+0xac/0xe0 [libsas]
[<ffffffffa0034914>] sas_ex_revalidate_domain+0x204/0x330 [libsas]
[<ffffffffa00307f0>] ? sas_revalidate_domain+0x0/0x90 [libsas]
[<ffffffffa0030855>] sas_revalidate_domain+0x65/0x90 [libsas]
[<ffffffff8108c7d0>] worker_thread+0x170/0x2a0
[<ffffffff81091ea0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff8108c660>] ? worker_thread+0x0/0x2a0
[<ffffffff81091b36>] kthread+0x96/0xa0
[<ffffffff810141ca>] child_rip+0xa/0x20
[<ffffffff81091aa0>] ? kthread+0x0/0xa0
[<ffffffff810141c0>] ? child_rip+0x0/0x20
Code: ff ff 85 c0 75 ed eb d6 66 90 55 48 89 e5 48 83 ec 10 48 89 1c 24
4c 89 64 24 08 0f 1f 44 00 00 48 89 fb e8 92 f4 ff ff 48 89 df <f0> ff
0f 79 05 e8 25 00 00 00 65 48 8b 04 25 08 cc 00 00 48 2d
RIP [<ffffffff814ca9b1>] mutex_lock+0x21/0x50
RSP <ffff8803e4e33d30>
CR2: 0000000000000238
The following patch is admittedly a band-aid, and does not solve the
root cause, but it still is a good candidate for hardening as a pointer
check before reference.
Signed-off-by: Mark Salyzyn <mark_salyzyn@us.xyratex.com>
Tested-by: Jack Wang <jack_wang@usish.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
I hit a crash in qla2x00_abort_all_cmds() if the qla2xxx module is
unloaded right after it is loaded. I debugged this down to the abort
handling improperly treating a command of type SRB_ADISC_CMD as if it
had a bsg_job to complete when that command actually uses the iocb_cmd
part of the union. (I guess to hit this one has to unload the module
while the async FC initialization is still in progress)
It seems we should only look for a bsg_job if type is SRB_ELS_CMD_RPT,
SRB_ELS_CMD_HST or SRB_CT_CMD, so switch the test to make that explicit.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
* 'v4l_for_linus' of git://linuxtv.org/mchehab/for_linus:
[media] omap3isp: Fix build error in ispccdc.c
[media] uvcvideo: Fix crash when linking entities
[media] v4l: Make sure we hold a reference to the v4l2_device before using it
[media] v4l: Fix use-after-free case in v4l2_device_release
[media] uvcvideo: Set alternate setting 0 on resume if the bus has been reset
[media] OMAP_VOUT: Fix build break caused by update_mode removal in DSS2
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] cio: fix cio_tpi ignoring adapter interrupts
[S390] gmap: always up mmap_sem properly
[S390] Do not clobber personality flags on exec
|
|
* 'drm-intel-fixes' of git://people.freedesktop.org/~keithp/linux:
drm/i915: FBC off for ironlake and older, otherwise on by default
drm/i915: Enable SDVO hotplug interrupts for HDMI and DVI
drm/i915: Enable dither whenever display bpc < frame buffer bpc
|
|
If request_irq fails, the ibmveth driver will overwrite
the rc and end up returning a successful rc on its open
function, resulting in an oops later when a packet gets
sent and buffers are not allocated due to the failed open.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix EEH recovery on new P Series platform by
requesting fundamental reset.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver has two warning messages that might be triggered
by normal use cases. When they appear, the messages give the
impression of a never ending series of errors.
This commit changes them to debug messages instead.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://github.com/davem330/net:
ipv6-multicast: Fix memory leak in IPv6 multicast.
ipv6: check return value for dst_alloc
net: check return value for dst_alloc
ipv6-multicast: Fix memory leak in input path.
bnx2x: add missing break in bnx2x_dcbnl_get_cap
bnx2x: fix WOL by enablement PME in config space
bnx2x: fix hw attention handling
net: fix a typo in Documentation/networking/scaling.txt
ath9k: Fix a dma warning/memory leak
rtlwifi: rtl8192cu: Fix unitialized struct
iwlagn: fix dangling scan request
batman-adv: do_bcast has to be true for broadcast packets only
cfg80211: Fix validation of AKM suites
iwlegacy: do not use interruptible waits
iwlegacy: fix command queue timeout
ath9k_hw: Fix Rx DMA stuck for AR9003 chips
|
