| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
V4L/DVB (10696): Remove outdated README for the flexcop-driver
V4L/DVB (10695): Update Technisat card documentation
V4L/DVB (10694): [PATCH] software IRQ watchdog for Flexcop B2C2 DVB PCI cards
V4L/DVB (10663): soc-camera: fix S_CROP breakage on PXA and SuperH
V4L/DVB (10659): em28xx: register device to soundcard for sysfs
|
|
Future iLO devices will have an HP vendor id.
Signed-off-by: David Altobelli <david.altobelli@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The w1_ds2433 driver does not read from the hardware if the CRC was valid
on the last read. The validcrc flag should be cleared after a write so
that the new value can be read.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With (some) Technisat cards you cannot run multiple DVB applications
in parallel and switch the channel at the same time.
There seems to be a problem on the interfaces or even inside the flexcop-device
that can't handle interruption on the streaming interface.
This patch adds a watchdog to check whether data is supposed to come in
(streaming PIDs are requested) and if no data is seen within 400ms (default) it
resets the streaming/pid-filtering hardware.
This patch is urgently needed to support the rev 2.8 of the hardware and solves
problem occassionally seen on older hardware.
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Recent format-negotiation patches caused S_CROP breakage in pxa_camera.c
and sh_mobile_ceu_camera.c drivers, fix it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
As explained in "Writing an ALSA driver" (T. Iwai), audio drivers should
set the struct device for the card before registering the card instance.
This will add the correct /sys/class/sound/cardN/device symlink, so HAL
can see the device and ConsoleKit sets its ACL permissions for the
logged-in user.
For em28xx audio capture cards found e.g. in Hauppauge WinTV-HVR-900 (R2),
this patch fixes errors like:
ALSA lib pcm_hw.c:1429:(_snd_pcm_hw_open) Invalid value for card
Error opening audio: Permission denied
when running mplayer as a normal user.
Signed-off-by: Nicola Soranzo <nsoranzo@tiscali.it>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
* git://git.infradead.org/mtd-2.6:
[MTD] [MAPS] Remove MODULE_DEVICE_TABLE() from ck804rom driver.
[JFFS2] fix mount crash caused by removed nodes
[JFFS2] force the jffs2 GC daemon to behave a bit better
[MTD] [MAPS] blackfin async requires complex mappings
[MTD] [MAPS] blackfin: fix memory leak in error path
[MTD] [MAPS] physmap: fix wrong free and del_mtd_{partition,device}
[MTD] slram: Handle negative devlength correctly
[MTD] map_rom has NULL erase pointer
[MTD] [LPDDR] qinfo_probe depends on lpddr
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: AMD 813x B2 devices do not need boot interrupt quirk
PCI: Enable PCIe AER only after checking firmware support
PCI: pciehp: Handle interrupts that happen during initialization.
PCI: don't enable too many HT MSI mappings
PCI: add some sysfs ABI docs
PCI quirk: enable MSI on 8132
|
|
Turns out that the new AMD 813x devices do not need the
quirk_disable_amd_813x_boot_interrupt quirk to be run on them. If it
is, no interrupts are seen on the PCI-X adapter.
From: Stefan Assmann <sassmann@novell.com>
Reported-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Tested-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
|
|
We really don't want the BIOS flash mapping hacks to get automatically
loaded.
No idea why it isn't using pci_register_driver() though -- that should
be fine... and is even _present_ but disabled by #if 0.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
xen/blkfront: use blk_rq_map_sg to generate ring entries
block: reduce stack footprint of blk_recount_segments()
cciss: shorten 30s timeout on controller reset
block: add documentation for register_blkdev()
block: fix bogus gcc warning for uninitialized var usage
|
|
It needs to happen before any firewire driver actually registers itself,
and that was previously handled by having the Makefile list the core
ieee1394 files before the drivers.
But now there are firewire drivers in drivers/media, and the Makefile
games aren't enough. So just make ieee1394_init happen earlier in the
init sequence, the way all other bus layers already do.
Reported-and-tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Henrik Kurelid <henrik@kurelid.se>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Ben Backx <ben@bbackx.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On occasion, the request will apparently have more segments than we
fit into the ring. Jens says:
> The second problem is that the block layer then appears to create one
> too many segments, but from the dump it has rq->nr_phys_segments ==
> BLKIF_MAX_SEGMENTS_PER_REQUEST. I suspect the latter is due to
> xen-blkfront not handling the merging on its own. It should check that
> the new page doesn't form part of the previous page. The
> rq_for_each_segment() iterates all single bits in the request, not dma
> segments. The "easiest" way to do this is to call blk_rq_map_sg() and
> then iterate the mapped sg list. That will give you what you are
> looking for.
> Here's a test patch, compiles but otherwise untested. I spent more
> time figuring out how to enable XEN than to code it up, so YMMV!
> Probably the sg list wants to be put inside the ring and only
> initialized on allocation, then you can get rid of the sg on stack and
> sg_init_table() loop call in the function. I'll leave that, and the
> testing, to you.
[Moved sg array into info structure, and initialize once. -J]
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
|
|
If reset_devices is set for kexec, then cciss will delay 30 seconds
since the old 5i controller _may_ need that long to recover. Replace
the long sleep with incremental sleep and tests to reduce the 30 seconds
to worst case for 5i, so that other controllers will proceed quickly.
Reviewed-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] pata_legacy: for VLB 32bit PIO don't try tricks with slop
[libata] pata_amd: program FIFO
sata_mv: fix SoC interrupt breakage
pata_it821x: resume from hibernation fails with RAID volume
|
|
These devices are generally used with ATA anyway and it seems that some
ATAPI will need us to issue the right number of words. Therefore as we
can't switch mid burst on VLB devices we should only use 32bit I/O for
suitable block sizes.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
With 32bit PIO we can use the posted write buffers, but only for 32bit I/O
cycles. This means we must disable the FIFO for ATAPI where a final 16bit
cycle may occur.
Rework the FIFO logic so that we disable the FIFO then selectively
re-enable it when we set the timings on AMD devices. Also fix a case
where we scribbled on PCI config 0x41 of Nvidia chips when we shouldn't.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
For some reason, sata_mv doesn't clear interrupt status during init
when it's running on an SoC host adapter. If the bootloader has
touched the SATA controller before starting Linux, Linux can end up
enabling the SATA interrupt with events pending, which will cause the
interrupt to be marked as spurious and then be disabled, which then
breaks all further accesses to the controller.
This patch makes the SoC path clear interrupt status on init like in
the non-SoC case.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Hibernation didn't work for me since I started to use IT8212 controller.
I did some debugging (booting with no_console_suspend init=/bin/sh).
Found that resume fails (2.6.28) with "serial number mismatch 'some
garbage' != 'some other garbage'" and "revalidation failed" messages.
That's because the controller firmware fills different serial number in
the IDENTIFY every boot.
The patch below fixes the resume simply clearing the serial number. The
proper fix would be probably to fill in the serial number of the RAID
volume instead. I assume that there must be something like that stored on
the drives but I don't know where.
Fix resume on pata_it821x RAID volume by clearing the serial number in
IDENTIFY data, which is otherwise different on each boot.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
During host driver module removal del_gendisk() results in a final
put on drive->gendev and freeing the drive by drive_release_dev().
Convert device drivers from using struct kref to use struct device
so device driver's object holds reference on ->gendev and prevents
drive from prematurely going away.
Also fix ->remove methods to not erroneously drop reference on a
host driver by using only put_device() instead of ide*_put().
Reported-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Just copy the comment from drivers/scsi/sr.c::sr_done()
(from which the capacity hack has been originated).
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Fix missing parentheses so PIO/DMA timings for master device on the
second channel are programmed correctly (IOW "8 0 24 16" offset values
should be used instead of the current "8 0 16 16").
[ The bug went unnoticed because after PIO/DMA timings get programmed
incorrectly for the third device they are overwritten with timings
for the fourth device and since BIOS should also program timings for
the third device everything should work fine until suspend/resume
cycle or user requested transfer mode changes. ]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
[bart: update patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Device and vendor ids were confused
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Documentation/kernel-parameters.txt
- ide=nodma is no longer valid.
drivers/ide/Kconfig
- The module is ide-core.ko not ide.
drivers/ide/ide.c
- It took me a while to figure out what the arguments %d.%d:%d to nodma
module parameter ment, so I added a comment to each.
- Added a comment to each of the sscanf lines.
- There is a bug, if j is 0 it would previously clear all the other bits
except the current device, changed in three different places.
mask &= (1 << i) should be mask &= ~(1 << i).
Signed-off-by: David Fries <david@fries.net>
[bart: s/disk/device/ in ide.c, beautify patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: convert DRM_ERROR to DRM_DEBUG in phys object pwrite path
drm/i915: make hw page ioremap use ioremap_wc
drm: edid revision 0 is valid
drm: Correct unbalanced drm_vblank_put() during mode setting.
drm: disable encoders before re-routing them
drm: Fix ordering of bit fields in EDID structure leading huge vsync values.
drm: Fix shifts of EDID vsync offset/width fields.
drm/i915: handle bogus VBT panel timing
drm/i915: remove PLL debugging messages
|
|
* 'for-linus' of git://neil.brown.name/md:
md: avoid races when stopping resync.
md/raid10: Don't call bitmap_cond_end_sync when we are doing recovery.
md/raid10: Don't skip more than 1 bitmap-chunk at a time during recovery.
|
|
* git://git.infradead.org/iommu-2.6:
intel-iommu: fix endless "Unknown DMAR structure type" loop
VT-d: handle Invalidation Queue Error to avoid system hang
intel-iommu: fix build error with INTR_REMAP=y and DMAR=n
|
|
When iwlan runs on IOMMU, IOMMU generates a lot of PTE write faults
because PTE write bit is not set on some of PTE's. This is because
iwlan driver calls DMA mapping with PCI_DMA_TODEVICE which is read only
in mapping PTE. But iwlan device actually writes to the mapped page to
update its contents. This issue is not exposed in swiotlb. But VT-d
hardware can capture this fault and stop the fault transaction.
The following patch fixes the issue.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Bhavesh Davda <bhavesh@vmware.com>
Tested-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This snuck in when I wrote phys object support.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
However we still have another issue with ioremap_wc not falling back
properly or somehow doing something else stupid, this probably needs
to be tracked down.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
edid->revision == 0 should be valid (at least, so the error message
indicates. :) and wikipedia seems to indicate that EDID 1.0 existed.
We can dump the entire check, since edid->revision is a u8, so
it can't ever be less than 0.
Marko reports in RH bz#476735 that his monitor claims to be
EDID 1.0, and therefore hits the check and is stuck at 800x600 because
of it.
Reported-by: Marko Ristola <marko.ristola@kolumbus.fi>
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
The first time we install a mode, the vblank will be disabled for a pipe
and so drm_vblank_get() in drm_vblank_pre_modeset() will fail. As we
unconditionally call drm_vblank_put() afterwards, the vblank reference
counter becomes unbalanced.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
In some cases we may receive a mode config that has a different
CRTC<->encoder map that the current configuration. In that case, we
need to disable any re-routed encoders before setting the mode,
otherwise they may not pick up the new CRTC (if the output types are
incompatible for example).
Tested-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
We've seen cases in the wild where the VBT sync data is wrong, so add
some code to fix it up in that case, taking care to make sure that the
total is greater than the sync end.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
These are normal; we walk through different values looking for the right
one, so why flood the screen with messages?
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
There has been a race in raid10 and raid1 for a long time
which has only recently started showing up due to a scheduler changed.
When a sync_read request finishes, as soon as reschedule_retry
is called, another thread can mark the resync request as having
completed, so md_do_sync can finish, ->stop can be called, and
->conf can be freed. So using conf after reschedule_retry is not
safe.
Similarly, when finishing a sync_write, calling md_done_sync must be
the last thing we do, as it allows a chain of events which will free
conf and other data structures.
The first of these requires action in raid10.c
The second requires action in raid1.c and raid10.c
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
For raid1/4/5/6, resync (fixing inconsistencies between devices) is
very similar to recovery (rebuilding a failed device onto a spare).
The both walk through the device addresses in order.
For raid10 it can be quite different. resync follows the 'array'
address, and makes sure all copies are the same. Recover walks
through 'device' addresses and recreates each missing block.
The 'bitmap_cond_end_sync' function allows the write-intent-bitmap
(When present) to be updated to reflect a partially completed resync.
It makes assumptions which mean that it does not work correctly for
raid10 recovery at all.
In particularly, it can cause bitmap-directed recovery of a raid10 to
not recovery some of the blocks that need to be recovered.
So move the call to bitmap_cond_end_sync into the resync path, rather
than being in the common "resync or recovery" path.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When doing recovery on a raid10 with a write-intent bitmap, we only
need to recovery chunks that are flagged in the bitmap.
However if we choose to skip a chunk as it isn't flag, the code
currently skips the whole raid10-chunk, thus it might not recovery
some blocks that need recovering.
This patch fixes it.
In case that is confusing, it might help to understand that there
is a 'raid10 chunk size' which guides how data is distributed across
the devices, and a 'bitmap chunk size' which says how much data
corresponds to a single bit in the bitmap.
This bug only affects cases where the bitmap chunk size is smaller
than the raid10 chunk size.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
Add i2c_board_info for RiscPC PCF8583
i2c: Make sure i2c_algo_bit_data.timeout is HZ-independent
i2c-dev: Clarify the unit of ioctl I2C_TIMEOUT
i2c: Timeouts reach -1
i2c: Fix misplaced parentheses
|
|
Add the necessary i2c_board_info structure to fix the lack of PCF8583
RTC on RiscPC.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
|
|
i2c_algo_bit_data.timeout is supposed to be in jiffies, so drivers
should use set this value in terms of HZ.
Ultimately I think this field should be discarded in favor of
i2c_adapter.timeout, but that's left for a future patch.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
|
|
The unit in which user-space can set the bus timeout value is jiffies
for historical reasons (back when HZ was always 100.) This is however
not good because user-space doesn't know how long a jiffy lasts. The
timeout value should instead be set in a fixed time unit. Given the
original value of HZ, this unit should be 10 ms, for compatibility.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
With a postfix decrement these timeouts reach -1 rather than 0, but
after the loop it is tested whether they have become 0.
As pointed out by Jean Delvare, the condition we are waiting for should
also be tested before the timeout. With the current order, you could
exit with a timeout error while the job is actually done.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Fix misplaced parentheses.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The PCIe port driver currently sets the PCIe AER error reporting bits for
any root or switch port without first checking to see if firmware will grant
control. This patch moves setting these bits to the AER service driver
aer_enable_port routine. The bits are then set for the root port and any
downstream switch ports after the check for firmware support (aer_osc_setup)
is made. The patch also unsets the bits in a similar fashion when the AER
service driver is unloaded.
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
|
|
Move the enabling of interrupts after all of the data structures
are setup so that we can safely run the interrupt handler as
soon as it is registered.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
|
|
Prakash reported that his c51-mcp51 ondie sound card doesn't work with
MSI. But if he hacks out the HT-MSI quirk, MSI works fine.
So this patch reworks the nv_msi_ht_cap_quirk(). It will now only
enable ht_msi on own its root device, avoiding enabling it on devices
following that root dev.
Reported-by: Prakash Punnoor <prakash@punnoor.de>
Tested-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
|
