Age | Commit message (Collapse) | Author |
|
The wakeup packet in the status response is padded out
to a multiple of 4 bytes by the firmware for transfer
to the host, take that into account when checking the
length of the command.
Also, the reported wakeup packet includes the FCS but
the userspace API doesn't, so remove that. If it is a
data packet it is reported as an 802.3 packet but I
forgot to take into account and remove the encryption
head/tail, fix all of that as well.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar.
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource : Nomadik-mtu : fix missing irq initialization
posix-timer: Don't call idr_find() with out-of-range ID
|
|
Use the new version of the encoding for osd requests and replies. In the
process, update the way we are tracking request ops and reply lengths and
results in the struct ceph_osd_request. Update the rbd and fs/ceph users
appropriately.
The main changes are:
- we keep pointers into the request memory for fields we need to update
each time the request is sent out over the wire
- we keep information about the result in an array in the request struct
where the users can easily get at it.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
|
|
The only thing type-specific osd completion functions do with their
osd op parameter is (in some cases) extract the number of bytes
transferred from it. In the other cases, the xferred bytes field
is not used, and total message data transfer byte count (which may
well be zero) is used.
Just set the object request transfer count in the main osd request
callback function and provide that to the other routines. There is
then no longer any need to pass the op pointer to the type-specific
completion routines, so drop those parameters.
Stop doing anything with the total message data length.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
|
|
This function is slightly out of place, probably the result
of an errant automatic merge or something.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"All trivial, thanks to the stuff which didn't quite make it time"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_console: Initialize guest_connected=true for rproc_serial
virtio: use module_virtio_driver.
virtio: Add module driver macro for virtio drivers.
virtio_console: Use virtio device index to generate port name
virtio: make pci_device_id const
virtio: make config_ops const
virtio-mmio: fix wrong comment about register offset
virtio_console: Let unconnected rproc device receive data.
|
|
Pull VFIO updates from Alex Williamson:
- Fixes PCIe v1 extended capability support
- Cleans up read/write access functions
- Fix Removal test to properly wait until devices are unused
- Enable pcieport driver usage for non-accessible devices w/in groups
- Extensions for PCI VGA support
* tag 'vfio-v3.9-rc1' of git://github.com/awilliam/linux-vfio:
drivers/vfio: remove depends on CONFIG_EXPERIMENTAL
vfio-pci: Add support for VGA region access
vfio-pci: Manage user power state transitions
vfio: whitelist pcieport
vfio: Protect vfio_dev_present against device_del
vfio-pci: Cleanup BAR access
vfio-pci: Cleanup read/write functions
vfio-pci: Enable PCIe extended capabilities on v1
|
|
Add missing usb_free_urb() on failure path in st5481_setup_usb().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Marina Makienko <makienko@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
in bond_enslave(), check slave_cnt before actually using slave address.
introduced by:
commit 409cc1f8a41 (bond: have random dev address by default instead of zeroes)
Reported-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make cpsw_add_default_vlan() look at the actual number of slaves for its
iteration, so boards with less than 2 slaves don't ooops at boot.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ben Hutchings says:
====================
Some fixes that should go into 3.9:
1. Fix packet corruption when using non-coherent RX DMA buffers.
2. Fix occasional watchdog misfiring when changing MTU or ring size.
These are longstanding bugs and should be fixed in stable as well, but
I'd like to review other recent fixes first and send a separate request
for stable inclusion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch (as1649) reverts commit
55bcdce8a8228223ec4d17d8ded8134ed265d2c5 (USB: EHCI: remove ASS/PSS
polling timeout). That commit was written under the assumption that
some controllers may take a very long time to turn off their async and
periodic schedules. It now appears that in fact the schedules do get
turned off reasonably quickly, but some controllers occasionally leave
the schedules' status bits turned on and consequently ehci-hcd can't
tell that the schedules are off.
VIA controllers in particular have this problem. ehci-hcd tells the
hardware to turn off the async schedule, the schedule does get turned
off, but the status bit remains on. Since the EHCI spec requires that
the schedules not be re-enabled until the previous disable has taken
effect, with an unlimited timeout the async schedule never gets turned
back on. The resulting symptom is that the system is unable to
communicate with USB devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Ronald <ronald645@gmail.com>
Reported-and-tested-by: Paul Hartman <paul.hartman@gmail.com>
Reported-and-tested-by: Dieter Nützel <dieter@nuetzel-hh.de>
Reported-and-tested-by: Jean Delvare <khali@linux-fr.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When stations are removed while packets are in the queue,
we drain the queues first, and then remove the stations.
If this happens in AP mode while the interface is removed
the MAC context might be removed from the firmware before
we removed the station(s), resulting in a SYSASSERT 3421.
This is because we remove the MAC context from the FW in
stop_ap(), but only flush the station drain work later in
remove_interface().
Refactor the code a bit to have a common MAC context
removal preparation first to solve this.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The FH hardware will always write back to the scratch field
in commands, even host commands not just TX commands, which
can overwrite parts of the command. This is problematic if
the command is re-used (with IWL_HCMD_DFL_NOCOPY) and can
cause calibration issues.
Address this problem by always putting at least the first
16 bytes into the buffer we also use for the command header
and therefore make the DMA engine write back into this.
For commands that are smaller than 16 bytes also always map
enough memory for the DMA engine to write back to.
Cc: stable@vger.kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Pull networking fixes from David Miller:
1) ping_err() ICMP error handler looks at wrong ICMP header, from Li
Wei.
2) TCP socket hash function on ipv6 is too weak, from Eric Dumazet.
3) netif_set_xps_queue() forgets to drop mutex on errors, fix from
Alexander Duyck.
4) sum_frag_mem_limit() can deadlock due to lack of BH disabling, fix
from Eric Dumazet.
5) TCP SYN data is miscalculated in tcp_send_syn_data(), because the
amount of TCP option space was not taken into account properly in
this code path. Fix from yuchung Cheng.
6) MLX4 driver allocates device queues with the wrong size, from Kleber
Sacilotto.
7) sock_diag can access past the end of the sock_diag_handlers[] array,
from Mathias Krause.
8) vlan_set_encap_proto() makes incorrect assumptions about where
skb->data points, rework the logic so that it works regardless of
where skb->data happens to be. From Jesse Gross.
9) Fix gianfar build failure with NET_POLL enabled, from Paul
Gortmaker.
10) Fix Ipv4 ID setting and checksum calculations in GRE driver, from
Pravin B Shelar.
11) bgmac driver does:
int i;
for (i = 0; ...; ...) {
...
for (i = 0; ...; ...) {
effectively corrupting the outer loop index, use a seperate
variable for the inner loops. From Rafał Miłecki.
12) Fix suspend bugs in smsc95xx driver, from Ming Lei.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
usbnet: smsc95xx: rename FEATURE_AUTOSUSPEND
usbnet: smsc95xx: fix broken runtime suspend
usbnet: smsc95xx: fix suspend failure
bgmac: fix indexing of 2nd level loops
b43: Fix lockdep splat on module unload
Revert "ip_gre: propogate target device GSO capability to the tunnel device"
IP_GRE: Fix GRE_CSUM case.
VXLAN: Use tunnel_ip_select_ident() for tunnel IP-Identification.
IP_GRE: Fix IP-Identification.
net/pasemi: Fix missing coding style
vmxnet3: fix ethtool ring buffer size setting
vmxnet3: make local function static
bnx2x: remove dead code and make local funcs static
gianfar: fix compile fail for NET_POLL=y due to struct packing
vlan: adjust vlan_set_encap_proto() for its callers
sock_diag: Simplify sock_diag_handlers[] handling in __sock_diag_rcv_msg
sock_diag: Fix out-of-bounds access to sock_diag_handlers[]
vxlan: remove depends on CONFIG_EXPERIMENTAL
mlx4_en: fix allocation of CPU affinity reverse-map
mlx4_en: fix allocation of device tx_cq
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull scsi target updates from Nicholas Bellinger:
"The highlights in this series include:
- Improve sg_table lookup scalability in RAMDISK_MCP (martin)
- Add device attribute to expose config name for INQUIRY model (tregaron)
- Convert tcm_vhost to use lock-less list for cmd completion (asias)
- Add tcm_vhost support for multiple target's per endpoint (asias)
- Add tcm_vhost support for multiple queues per vhost (asias)
- Add missing mapped_lun bounds checking during make_mappedlun setup
in generic fabric configfs code (jan engelhardt + nab)
- Enforce individual iscsi-target network portal export once per
TargetName endpoint (grover + nab)
- Add WRITE_SAME w/ UNMAP=0 emulation to FILEIO backend (nab)
Things have been mostly quiet this round, with majority of the work
being done on the iser-target WIP driver + associated iscsi-target
refactoring patches currently in flight for v3.10 code.
At this point there is one patch series left outstanding from Asias to
add support for UNMAP + WRITE_SAME w/ UNMAP=1 to FILEIO awaiting
feedback from hch & Co, that will likely be included in a post
v3.9-rc1 PULL request if there are no objections.
Also, there is a regression bug recently reported off-list that seems
to be effecting v3.5 and v3.6 kernels with MSFT iSCSI initiators that
is still being tracked down. No word if this effects >= v3.7 just
yet, but if so there will likely another PULL request coming your
way.."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (26 commits)
target: Rename spc_get_write_same_sectors -> sbc_get_write_same_sectors
target/file: Add WRITE_SAME w/ UNMAP=0 emulation support
iscsi-target: Enforce individual network portal export once per TargetName
iscsi-target: Refactor iscsit_get_np sockaddr matching into iscsit_check_np_match
target: Add missing mapped_lun bounds checking during make_mappedlun setup
target: Fix lookup of dynamic NodeACLs during cached demo-mode operation
target: Fix parameter list length checking in MODE SELECT
target: Fix error checking for UNMAP commands
target: Fix sense data for out-of-bounds IO operations
target_core_rd: break out unterminated loop during copy
tcm_vhost: Multi-queue support
tcm_vhost: Multi-target support
target: Add device attribute to expose config_item_name for INQUIRY model
target: don't truncate the fail intr address
target: don't always say "ipv6" as address type
target/iblock: Use backend REQ_FLUSH hint for WriteCacheEnabled status
iscsi-target: make some temporary buffers larger
tcm_vhost: Optimize gup in vhost_scsi_map_to_sgl
tcm_vhost: Use iov_num_pages to calculate sgl_count
tcm_vhost: Introduce iov_num_pages
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband update from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.9:
- SRP error handling fixes from Bart Van Assche
- Implementation of memory windows for mlx4 from Shani Michaeli
- Lots of cxgb4 HW driver fixes from Vipul Pandya
- Make iSER work for virtual functions, other fixes from Or Gerlitz
- Fix for bug in qib HW driver from Mike Marciniszyn
- IPoIB fixes from me, Itai Garbi, Shlomo Pongratz, Yan Burman
- Various cleanups and warning fixes from Julia Lawall, Paul Bolle,
Wei Yongjun"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (41 commits)
IB/mlx4: Advertise MW support
IB/mlx4: Support memory window binding
mlx4: Implement memory windows allocation and deallocation
mlx4_core: Enable memory windows in {INIT, QUERY}_HCA
mlx4_core: Disable memory windows for virtual functions
IPoIB: Free ipoib neigh on path record failure so path rec queries are retried
IB/srp: Fail I/O requests if the transport is offline
IB/srp: Avoid endless SCSI error handling loop
IB/srp: Avoid sending a task management function needlessly
IB/srp: Track connection state properly
IB/mlx4: Remove redundant NULL check before kfree
IB/mlx4: Fix compiler warning about uninitialized 'vlan' variable
IB/mlx4: Convert is_xxx variables in build_mlx_header() to bool
IB/iser: Enable iser when FMRs are not supported
IB/iser: Avoid error prints on EAGAIN registration failures
IB/iser: Use proper define for the commands per LUN value advertised to SCSI ML
IB/uverbs: Implement memory windows support in uverbs
IB/core: Add "type 2" memory windows support
mlx4_core: Propagate MR deregistration failures to caller
mlx4_core: Rename MPT-related functions to have mpt_ prefix
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU Updates from Joerg Roedel:
"Besides some fixes and cleanups in the code there are three more
important changes to point out this time:
* New IOMMU driver for the ARM SHMOBILE platform
* An IOMMU-API extension for non-paging IOMMUs (required for
upcoming PAMU driver)
* Rework of the way the Tegra IOMMU driver accesses its
registetrs - register windows are easier to extend now.
There are also a few changes to non-iommu code, but that is acked by
the respective maintainers."
* tag 'iommu-updates-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (23 commits)
iommu/tegra: assume CONFIG_OF in SMMU driver
iommu/tegra: assume CONFIG_OF in gart driver
iommu/amd: Remove redundant NULL check before dma_ops_domain_free().
iommu/amd: Initialize device table after dma_ops
iommu/vt-d: Zero out allocated memory in dmar_enable_qi
iommu/tegra: smmu: Fix incorrect mask for regbase
iommu/exynos: Make exynos_sysmmu_disable static
ARM: mach-shmobile: r8a7740: Add IPMMU device
ARM: mach-shmobile: sh73a0: Add IPMMU device
ARM: mach-shmobile: sh7372: Add IPMMU device
iommu/shmobile: Add iommu driver for Renesas IPMMU modules
iommu: Add DOMAIN_ATTR_WINDOWS domain attribute
iommu: Add domain window handling functions
iommu: Implement DOMAIN_ATTR_PAGING attribute
iommu: Check for valid pgsize_bitmap in iommu_map/unmap
iommu: Make sure DOMAIN_ATTR_MAX is really the maximum
iommu/tegra: smmu: Change SMMU's dependency on ARCH_TEGRA
iommu/tegra: smmu: Use helper function to check for valid register offset
iommu/tegra: smmu: Support variable MMIO ranges/blocks
iommu/tegra: Add missing spinlock initialization
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Highlights:
- new drivers for Intel ismt & Broadcom bcm2835
- a number of drivers got support for more variants and mostly got
cleaned up on the way (sis630, i801, at91, tegra, designware)
- i2c got rid of all *_set_drvdata(..., NULL) on remove/probe failure
- removed the i2c_smbus_process_call from the core since there are no
users
- mxs can now switch between PIO and DMA depending on the message
size and the bus speed can now be arbitrary
In addition, there is the usual bunch of fixes, cleanups, devm_*
conversions, etc"
Fixed conflict (and buggy devm_* conversion) in i2c-s3c2410.c
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (39 commits)
i2c: Remove unneeded xxx_set_drvdata(..., NULL) calls
i2c: pxa: remove incorrect __exit annotations
i2c: ocores: Fix pointer to integer cast warning
i2c: tegra: remove warning dump if timeout happen in transfer
i2c: fix i2c-ismt.c printk format warning
i2c: i801: Add Device IDs for Intel Wellsburg PCH
i2c: add bcm2835 driver
i2c: ismt: Add Seth and Myself as maintainers
i2c: sis630: checkpatch cleanup
i2c: sis630: display unsigned hex
i2c: sis630: use hex to constants for SMBus commands
i2c: sis630: fix behavior after collision
i2c: sis630: clear sticky bits
i2c: sis630: Add SIS964 support
i2c: isch: Add module parameter for backbone clock rate if divider is unset
i2c: at91: fix unsed variable warning when building with !CONFIG_OF
i2c: Adding support for Intel iSMT SMBus 2.0 host controller
i2c: sh_mobile: don't send a stop condition by default inside transfers
i2c: sh_mobile: eliminate an open-coded "goto" loop
i2c: sh_mobile: fix timeout error handling
...
|
|
Pull GPIO changes from Grant Likely:
"This branch contains the usual set of individual driver improvements
and bug fixes, as well as updates to the core code. The more notable
changes include:
- Internally add new API for referencing GPIOs by gpio_desc instead
of number. Eventually this will become a public API
- ACPI GPIO binding support"
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux: (33 commits)
arm64: select ARCH_WANT_OPTIONAL_GPIOLIB
gpio: em: Use irq_domain_add_simple() to fix runtime error
gpio: using common order: let 'static const' instead of 'const static'
gpio/vt8500: memory cleanup missing
gpiolib: Fix locking on gpio debugfs files
gpiolib: let gpio_chip reference its descriptors
gpiolib: use descriptors internally
gpiolib: use gpio_chips list in gpiochip_find_base
gpiolib: use gpio_chips list in sysfs ops
gpiolib: use gpio_chips list in gpiochip_find
gpiolib: use gpio_chips list in gpiolib_sysfs_init
gpiolib: link all gpio_chips using a list
gpio/langwell: cleanup driver
gpio/langwell: Add Cloverview ids to pci device table
gpio/lynxpoint: add chipset gpio driver.
gpiolib: add missing braces in gpio_direction_show
gpiolib-acpi: Fix error checks in interrupt requesting
gpio: mpc8xxx: don't set IRQ_TYPE_NONE when creating irq mapping
gpiolib: remove gpiochip_reserve()
arm: pxa: tosa: do not use gpiochip_reserve()
...
|
|
Pull PWM changes from Thierry Reding:
"A new driver has been added to support the PWM mode of the timer
counter blocks found on Atmel AT91 SoCs. The VT8500 driver now
supports changing the PWM signal polarity and the TI drivers (EHRPWM
and ECAP) gained suspend and resume functionality.
User drivers can now query the core for whether access to a PWM device
will sleep (if the PWM chip is on a slow bus such as I2C or SPI).
The pwm-backlight driver now handles the backlight BL_CORE_FBBLANK
state in addition to the FB layer's blanking states.
To round things off, a few fixes and cleanups are also included"
* tag 'for-3.9-rc1' of git://gitorious.org/linux-pwm/linux-pwm:
pwm: twl: Use to_twl() instead of container_of()
pwm: tegra: assume CONFIG_OF
pwm_backlight: Validate dft_brightness in main probe function
pwm: Export pwm_{set,get}_chip_data()
pwm: Make Kconfig entries more consistent
pwm: Add can_sleep property to drivers
pwm: Add pwm_can_sleep() as exported API to users
pwm-backlight: handle BL_CORE_FBBLANK state
pwm: pwm-tiecap: Low power sleep support
pwm: pwm-tiehrpwm: Low power sleep support
pwm: pwm-tiehrpwm: Update the clock handling of pwm-tiehrpwm driver
pwm: vt8500: Add polarity support
pwm: vt8500: Register write busy test performed incorrectly
pwm: atmel: add Timer Counter Block PWM driver
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC update from Chris Ball:
"MMC highlights for 3.9:
Core:
- Support for packed commands in eMMC 4.5. (This requires a host
capability to be turned on. It increases write throughput by 20%+,
but may also increase average write latency; more testing needed.)
- Add DT bindings for capability flags.
- Add mmc_of_parse() for shared DT parsing between drivers.
Drivers:
- android-goldfish: New MMC driver for the Android Goldfish emulator.
- mvsdio: Add DT bindings, pinctrl, use slot-gpio for card detection.
- omap_hsmmc: Fix boot hangs with RPMB partitions.
- sdhci-bcm2835: New driver for controller used by Raspberry Pi.
- sdhci-esdhc-imx: Add 8-bit data, auto CMD23 support, use slot-gpio.
- sh_mmcif: Add support for eMMC DDR, bundled MMCIF IRQs.
- tmio_mmc: Add DT bindings, support for vccq regulator"
* tag 'mmc-updates-for-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (92 commits)
mmc: tegra: assume CONFIG_OF, remove platform data
mmc: add DT bindings for more MMC capability flags
mmc: tmio: add support for the VccQ regulator
mmc: tmio: remove unused and deprecated symbols
mmc: sh_mobile_sdhi: use managed resource allocations
mmc: sh_mobile_sdhi: remove unused .pdata field
mmc: tmio-mmc: parse device-tree bindings
mmc: tmio-mmc: define device-tree bindings
mmc: sh_mmcif: use mmc_of_parse() to parse standard MMC DT bindings
mmc: (cosmetic) remove "extern" from function declarations
mmc: provide a standard MMC device-tree binding parser centrally
mmc: detailed definition of CD and WP MMC line polarities in DT
mmc: sdhi, tmio: only check flags in tmio-mmc driver proper
mmc: sdhci: Fix parameter of sdhci_do_start_signal_voltage_switch()
mmc: sdhci: check voltage range only on regulators aware of voltage value
mmc: bcm2835: set SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK
mmc: support packed write command for eMMC4.5 devices
mmc: add packed command feature of eMMC4.5
mmc: rtsx: remove driving adjustment
mmc: use regulator_can_change_voltage() instead of regulator_count_voltages
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds
Pull LED subsystem update from Bryan Wu.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (61 commits)
leds: leds-sunfire: use dev_err()/pr_err() instead of printk()
leds: 88pm860x: Add missing of_node_put()
leds: tca6507: Use of_get_child_count()
leds: leds-pwm: make it depend on PWM and not HAVE_PWM
Documentation: leds: update LP55xx family devices
leds-lp55xx: fix problem on removing LED attributes
leds-lp5521/5523: add author and copyright description
leds-lp5521/5523: use new lp55xx common header
leds-lp55xx: clean up headers
leds-lp55xx: clean up definitions
leds-lp55xx: clean up unused data and functions
leds-lp55xx: clean up _remove()
leds-lp55xx: add new function for removing device attribtues
leds-lp55xx: code refactoring on selftest function
leds-lp55xx: use common device attribute driver function
leds-lp55xx: support device specific attributes
leds-lp5523: use generic firmware interface
leds-lp5521: use generic firmware interface
leds-lp55xx: support firmware interface
leds-lp55xx: add new lp55xx_register_sysfs() for the firmware interface
...
|
|
Pull slave-dmaengine updates from Vinod Koul:
"This is fairly big pull by my standards as I had missed last merge
window. So we have the support for device tree for slave-dmaengine,
large updates to dw_dmac driver from Andy for reusing on different
architectures. Along with this we have fixes on bunch of the drivers"
Fix up trivial conflicts, usually due to #include line movement next to
each other.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (111 commits)
Revert "ARM: SPEAr13xx: Pass DW DMAC platform data from DT"
ARM: dts: pl330: Add #dma-cells for generic dma binding support
DMA: PL330: Register the DMA controller with the generic DMA helpers
DMA: PL330: Add xlate function
DMA: PL330: Add new pl330 filter for DT case.
dma: tegra20-apb-dma: remove unnecessary assignment
edma: do not waste memory for dma_mask
dma: coh901318: set residue only if dma is in progress
dma: coh901318: avoid unbalanced locking
dmaengine.h: remove redundant else keyword
dma: of-dma: protect list write operation by spin_lock
dmaengine: ste_dma40: do not remove descriptors for cyclic transfers
dma: of-dma.c: fix memory leakage
dw_dmac: apply default dma_mask if needed
dmaengine: ioat - fix spare sparse complain
dmaengine: move drivers/of/dma.c -> drivers/dma/of-dma.c
ioatdma: fix race between updating ioat->head and IOAT_COMPLETION_PENDING
dw_dmac: add support for Lynxpoint DMA controllers
dw_dmac: return proper residue value
dw_dmac: fill individual length of descriptor
...
|
|
'srp' into for-next
|
|
We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned. Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.
The device is ready if all the following are true:
(a) It has a qdisc
(b) It is marked present
(c) It is running
(d) The link is reported up
(a) and (c) are normally true, and must not be changed by a driver.
(d) is under our control, but fake link changes may disturb userland.
This leaves (b). We already mark the device absent during reset
and self-test, but we need to do the same during MTU changes and ring
reallocation. We don't need to do this when the device is brought
down because then (c) is already false.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
We assume that the mapping between DMA and virtual addresses is done
on whole pages, so we can find the page offset of an RX buffer using
the lower bits of the DMA address. However, swiotlb maps in units of
2K, breaking this assumption.
Add an explicit page_offset field to struct efx_rx_buffer.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
We may currently allocate two RX DMA buffers to a page, and only unmap
the page when the second is completed. We do not sync the first RX
buffer to be completed; this can result in packet loss or corruption
if the last RX buffer completed in a NAPI poll is the first in a page
and is not DMA-coherent. (In the middle of a NAPI poll, we will
handle the following RX completion and unmap the page *before* looking
at the content of the first buffer.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
This removes an open coded simple_open() function and
replaces file operations references to the function
with simple_open() instead.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Since we will remove items off the list using list_del() we need
to use a safe version of the list_for_each_entry() macro aptly named
list_for_each_entry_safe().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
... in other news:
filp_open() can't return a struct file with NULL dentry
filp_open() can't return a struct file negative dentry
filp_close() of something that never had been in any descriptor
tables is pointless - fput() is all you need
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
file argument is a struct file being passed to ->open() or
already opened; none of the checks in lirc_get_pdata()
can fail.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Fixes for blackfin and microblaze build problems introduced by the
removal of global pm_idle. From Lars-Peter Clausen.
- OPP core build fix from Shawn Guo.
- Error condition check fix for the new imx6q-cpufreq driver from Wei
Yongjun.
- Fix for an AER driver crash related to the lack of APEI
initialization for acpi=off. From Rafael J Wysocki.
- Fix for a USB breakage on Thinkpad T430 related to ACPI power
resources and PCI wakeup from Rafael J. Wysocki.
* tag 'pm+acpi-fixes-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PM: Take unusual configurations of power resources into account
imx6q-cpufreq: fix return value check in imx6q_cpufreq_probe()
PM / OPP: fix condition for empty of_init_opp_table()
ACPI / APEI: Fix crash in apei_hest_parse() for acpi=off
microblaze idle: Fix compile error
blackfin idle: Fix compile error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Major overhaul of ACPI host bridge add/start (Rafael Wysocki, Yinghai Lu)
- Major overhaul of PCI/ACPI binding (Rafael Wysocki, Yinghai Lu)
- Split out ACPI host bridge and ACPI PCI device hotplug (Yinghai Lu)
- Stop caching _PRT and make independent of bus numbers (Yinghai Lu)
PCI device hotplug
- Clean up cpqphp dead code (Sasha Levin)
- Disable ARI unless device and upstream bridge support it (Yijing Wang)
- Initialize all hot-added devices (not functions 0-7) (Yijing Wang)
Power management
- Don't touch ASPM if disabled (Joe Lawrence)
- Fix ASPM link state management (Myron Stowe)
Miscellaneous
- Fix PCI_EXP_FLAGS accessor (Alex Williamson)
- Disable Bus Master in pci_device_shutdown (Konstantin Khlebnikov)
- Document hotplug resource and MPS parameters (Yijing Wang)
- Add accessor for PCIe capabilities (Myron Stowe)
- Drop pciehp suspend/resume messages (Paul Bolle)
- Make pci_slot built-in only (not a module) (Jiang Liu)
- Remove unused PCI/ACPI bind ops (Jiang Liu)
- Removed used pci_root_bus (Bjorn Helgaas)"
* tag 'pci-v3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
PCI/ACPI: Don't cache _PRT, and don't associate them with bus numbers
PCI: Fix PCI Express Capability accessors for PCI_EXP_FLAGS
ACPI / PCI: Make pci_slot built-in only, not a module
PCI/PM: Clear state_saved during suspend
PCI: Use atomic_inc_return() rather than atomic_add_return()
PCI: Catch attempts to disable already-disabled devices
PCI: Disable Bus Master unconditionally in pci_device_shutdown()
PCI: acpiphp: Remove dead code for PCI host bridge hotplug
PCI: acpiphp: Create companion ACPI devices before creating PCI devices
PCI: Remove unused "rc" in virtfn_add_bus()
PCI: pciehp: Drop suspend/resume ENTRY messages
PCI/ASPM: Don't touch ASPM if forcibly disabled
PCI/ASPM: Deallocate upstream link state even if device is not PCIe
PCI: Document MPS parameters pci=pcie_bus_safe, pci=pcie_bus_perf, etc
PCI: Document hpiosize= and hpmemsize= resource reservation parameters
PCI: Use PCI Express Capability accessor
PCI: Introduce accessor to retrieve PCIe Capabilities Register
PCI: Put pci_dev in device tree as early as possible
PCI: Skip attaching driver in device_add()
PCI: acpiphp: Keep driver loaded even if no slots found
...
|
|
When raid1/raid10 needs to fix a read error, it first drains
all pending requests by calling freeze_array().
This calls flush_pending_writes() if it needs to sleep,
but some writes may be pending in a per-process plug rather
than in the per-array request queue.
When raid1{,0}_unplug() moves the request from the per-process
plug to the per-array request queue (from which
flush_pending_writes() can flush them), it needs to wake up
freeze_array(), or freeze_array() will never flush them and so
it will block forever.
So add the requires wake_up() calls.
This bug was introduced by commit
f54a9d0e59c4bea3db733921ca9147612a6f292c
for raid1 and a similar commit for RAID10, and so has been present
since linux-3.6. As the bug causes a deadlock I believe this fix is
suitable for -stable.
Cc: stable@vger.kernel.org (3.6.y 3.7.y 3.8.y)
Reported-by: Tregaron Bayly <tbayly@bluehost.com>
Tested-by: Tregaron Bayly <tbayly@bluehost.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Mentioning "bad disk number -1" exposes irrelevant internal detail.
Just say they are inactive and must be removed.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Create_stripe_zones returns an error slightly differently to
raid0_run and to raid0_takeover_*.
The error returned used by the second was wrong and an error would
result in mddev->private being set to NULL and sooner or later a
crash.
So never return NULL, return ERR_PTR(err), not NULL from
create_stripe_zones.
This bug has been present since 2.6.35 so the fix is suitable
for any kernel since then.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
You cannot resize a RAID0 array (in terms of making the devices
bigger), but the code doesn't entirely stop you.
So:
disable setting of the available size on each device for
RAID0 and Linear devices. This must not change as doing so
can change the effective layout of data.
Make sure that the size that raid0_size() reports is accurate,
but rounding devices sizes to chunk sizes. As the device sizes
cannot change now, this isn't so important, but it is best to be
safe.
Without this change:
mdadm --grow /dev/md0 -z max
mdadm --grow /dev/md0 -Z max
then read to the end of the array
can cause a BUG in a RAID0 array.
These bugs have been present ever since it became possible
to resize any device, which is a long time. So the fix is
suitable for any -stable kerenl.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
DM RAID: Add support for MD's RAID10 "far" and "offset" algorithms
Until now, dm-raid.c only supported the "near" algorthm of MD's RAID10
implementation. This patch adds support for the "far" and "offset"
algorithms, but only with the improved redundancy that is brought with
the introduction of the 'use_far_sets' bit, which shifts copied stripes
according to smaller sets vs the entire array. That is, the 17th bit
of the 'layout' variable that defines the RAID10 implementation will
always be set. (More information on how the 'layout' variable selects
the RAID10 algorithm can be found in the opening comments of
drivers/md/raid10.c.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
MD RAID10: Improve redundancy for 'far' and 'offset' algorithms (part 2)
This patch addresses raid arrays that have a number of devices that cannot
be evenly divided by 'far_copies'. (E.g. 5 devices, far_copies = 2) This
case must be handled differently because it causes that last set to be of
a different size than the rest of the sets. We must compute a new modulo
for this last set so that copied chunks are properly wrapped around.
Example use_far_sets=1, far_copies=2, near_copies=1, devices=5:
"far" algorithm
dev1 dev2 dev3 dev4 dev5
==== ==== ==== ==== ====
[ A B ] [ C D E ]
[ G H ] [ I J K ]
...
[ B A ] [ E C D ] --> nominal set of 2 and last set of 3
[ H G ] [ K I J ] []'s show far/offset sets
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
The MD RAID10 'far' and 'offset' algorithms make copies of entire stripe
widths - copying them to a different location on the same devices after
shifting the stripe. An example layout of each follows below:
"far" algorithm
dev1 dev2 dev3 dev4 dev5 dev6
==== ==== ==== ==== ==== ====
A B C D E F
G H I J K L
...
F A B C D E --> Copy of stripe0, but shifted by 1
L G H I J K
...
"offset" algorithm
dev1 dev2 dev3 dev4 dev5 dev6
==== ==== ==== ==== ==== ====
A B C D E F
F A B C D E --> Copy of stripe0, but shifted by 1
G H I J K L
L G H I J K
...
Redundancy for these algorithms is gained by shifting the copied stripes
one device to the right. This patch proposes that array be divided into
sets of adjacent devices and when the stripe copies are shifted, they wrap
on set boundaries rather than the array size boundary. That is, for the
purposes of shifting, the copies are confined to their sets within the
array. The sets are 'near_copies * far_copies' in size.
The above "far" algorithm example would change to:
"far" algorithm
dev1 dev2 dev3 dev4 dev5 dev6
==== ==== ==== ==== ==== ====
A B C D E F
G H I J K L
...
B A D C F E --> Copy of stripe0, shifted 1, 2-dev sets
H G J I L K Dev sets are 1-2, 3-4, 5-6
...
This has the affect of improving the redundancy of the array. We can
always sustain at least one failure, but sometimes more than one can
be handled. In the first examples, the pairs of devices that CANNOT fail
together are:
(1,2) (2,3) (3,4) (4,5) (5,6) (1, 6) [40% of possible pairs]
In the example where the copies are confined to sets, the pairs of
devices that cannot fail together are:
(1,2) (3,4) (5,6) [20% of possible pairs]
We cannot simply replace the old algorithms, so the 17th bit of the 'layout'
variable is used to indicate whether we use the old or new method of computing
the shift. (This is similar to the way the 16th bit indicates whether the
"far" algorithm or the "offset" algorithm is being used.)
This patch only handles the cases where the number of total raid disks is
a multiple of 'far_copies'. A follow-on patch addresses the condition where
this is not true.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Changes include assigning 'addr' from 's' instead of 'sector' to be
consistent with the way the code does it just a few lines later and
using '%=' vs a conditional and subtraction.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Set mddev queue's max_write_same_sectors to its chunk_sector value (before
disk_stack_limits merges the underlying disk limits.) With that in place,
be sure to handle writes coming down from the block layer that have the
REQ_WRITE_SAME flag set. That flag needs to be copied into any newly cloned
write bio.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Pull drm merge from Dave Airlie:
"Highlights:
- TI LCD controller KMS driver
- TI OMAP KMS driver merged from staging
- drop gma500 stub driver
- the fbcon locking fixes
- the vgacon dirty like zebra fix.
- open firmware videomode and hdmi common code helpers
- major locking rework for kms object handling - pageflip/cursor
won't block on polling anymore!
- fbcon helper and prime helper cleanups
- i915: all over the map, haswell power well enhancements, valleyview
macro horrors cleaned up, killing lots of legacy GTT code,
- radeon: CS ioctl unification, deprecated UMS support, gpu reset
rework, VM fixes
- nouveau: reworked thermal code, external dp/tmds encoder support
(anx9805), fences sleep instead of polling,
- exynos: all over the driver fixes."
Lovely conflict in radeon/evergreen_cs.c between commit de0babd60d8d
("drm/radeon: enforce use of radeon_get_ib_value when reading user cmd")
and the new changes that modified that evergreen_dma_cs_parse()
function.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (508 commits)
drm/tilcdc: only build on arm
drm/i915: Revert hdmi HDP pin checks
drm/tegra: Add list of framebuffers to debugfs
drm/tegra: Fix color expansion
drm/tegra: Split DC_CMD_STATE_CONTROL register write
drm/tegra: Implement page-flipping support
drm/tegra: Implement VBLANK support
drm/tegra: Implement .mode_set_base()
drm/tegra: Add plane support
drm/tegra: Remove bogus tegra_framebuffer structure
drm: Add consistency check for page-flipping
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
gma500: Fix n, m1 and m2 clock limits for sdvo and lvds
...
|
|
Pull crypto update from Herbert Xu:
"Here is the crypto update for 3.9:
- Added accelerated implementation of crc32 using pclmulqdq.
- Added test vector for fcrypt.
- Added support for OMAP4/AM33XX cipher and hash.
- Fixed loose crypto_user input checks.
- Misc fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (43 commits)
crypto: user - ensure user supplied strings are nul-terminated
crypto: user - fix empty string test in report API
crypto: user - fix info leaks in report API
crypto: caam - Added property fsl,sec-era in SEC4.0 device tree binding.
crypto: use ERR_CAST
crypto: atmel-aes - adjust duplicate test
crypto: crc32-pclmul - Kill warning on x86-32
crypto: x86/twofish - assembler clean-ups: use ENTRY/ENDPROC, localize jump labels
crypto: x86/sha1 - assembler clean-ups: use ENTRY/ENDPROC
crypto: x86/serpent - use ENTRY/ENDPROC for assember functions and localize jump targets
crypto: x86/salsa20 - assembler cleanup, use ENTRY/ENDPROC for assember functions and rename ECRYPT_* to salsa20_*
crypto: x86/ghash - assembler clean-up: use ENDPROC at end of assember functions
crypto: x86/crc32c - assembler clean-up: use ENTRY/ENDPROC
crypto: cast6-avx: use ENTRY()/ENDPROC() for assembler functions
crypto: cast5-avx: use ENTRY()/ENDPROC() for assembler functions and localize jump targets
crypto: camellia-x86_64/aes-ni: use ENTRY()/ENDPROC() for assembler functions and localize jump targets
crypto: blowfish-x86_64: use ENTRY()/ENDPROC() for assembler functions and localize jump targets
crypto: aesni-intel - add ENDPROC statements for assembler functions
crypto: x86/aes - assembler clean-ups: use ENTRY/ENDPROC, localize jump targets
crypto: testmgr - add test vector for fcrypt
...
|
|
[airlied: hack for now until we fix cma helpers on other OF platforms]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dave Airlie <airlied@linux.ie>
|