| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (21 commits)
[media] mceusb: set a default rx timeout
[media] mceusb: fix inverted mask inversion logic
[media] mceusb: add another Fintek device ID
[media] lirc_dev: fixes in lirc_dev_fop_read()
[media] lirc_dev: stray unlock in lirc_dev_fop_poll()
[media] rc: fix sysfs entry for mceusb and streamzap
[media] streamzap: merge timeout space with trailing space
[media] mceusb: fix keybouce issue after parser simplification
[media] IR: add tv power scancode to rc6 mce keymap
[media] mceusb: buffer parsing fixups for 1st-gen device
[media] mceusb: fix up reporting of trailing space
[media] nuvoton-cir: improve buffer parsing responsiveness
[media] mceusb: add support for Conexant Hybrid TV RDU253S
[media] s5p-fimc: Fix output DMA handling in S5PV310 IP revisions
[media] s5p-fimc: Use correct fourcc code for 32-bit RGB format
[media] s5p-fimc: Convert m2m driver to unlocked_ioctl
[media] s5p-fimc: Explicitly add required header file
[media] s5p-fimc: Fix vidioc_g_crop/cropcap on camera sensor
[media] s5p-fimc: BKL lock removal - compilation fix
[media] soc-camera: fix static build of the sh_mobile_csi2.c driver
...
|
|
The default for non-READ_BACK GPIO regs is to have the clear bits set;
this means that our original errata fix was too simplistic. This
changes it to the following behavior:
- when setting GPIOs, ignore the higher order bits (they're for
clearing, we don't need to care about them).
- when clearing GPIOs, keep all the bits, but unset (via XOR) the
lower order bit that negates the clear bit that we care about. That
is, if we're clearing GPIO 26 (val = 0x04000000), we first XOR what's
currently in the register with 0x0400 (GPIO 26's SET bit), and then
OR that with the GPIO 26's CLEAR bit.
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The edge detect status GPIOs function differently from the other atomic
model CS5536 GPIO registers; writing 1 to the high bits clears the GPIO,
but writing 1 to the lower bits also clears the bit.
This means that read-modify-write doesn't actually work for it, so don't
apply the errata here. If a negative edge status gets lost after
resume.. well, we tried our best!
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Include the connector name in the output_poll_execute() debug message
drm/radeon/kms: fix bug in r600_gpu_is_lockup
drm/radeon/kms: reorder display resume to avoid problems
drm/radeon/kms/evergreen: reset the grbm blocks at resume and init
drm/radeon/kms: fix evergreen asic reset
Revert "drm: Don't try and disable an encoder that was never enabled"
drm/radeon: Add early unregister of firmware fb's
drm/radeon: use aperture size not vram size for overlap tests
drm/radeon/kms/evergreen: flush hdp cache when flushing gart tlb
drm/radeon/kms: disable the r600 cb offset checker for linear surfaces
drm/radeon/kms: disable ss fixed ref divide
drm/i915/bios: Reverse order of 100/120 Mhz SSC clocks
agp/intel: Fix missed cached memory flags setting in i965_write_entry()
drm/i915/sdvo: Only use the SDVO pin if it is in the valid range
drm/i915/ringbuffer: Handle wrapping of the autoreported HEAD
drm/i915/dp: Fix I2C/EDID handling with active DisplayPort to DVI converter
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Support additional parent IDs for wm831x
mfd: Fix ab8500-core interrupt ffs bit bug
mfd: Supply IRQ base for WM832x devices
watchdog: Fix null pointer dereference while accessing rdc321x platform_data
gpio: Fix null pointer dereference while accessing rdc321x platform_data
|
|
This was fixed by David Lamparter in v2.6.36-rc5 3486008 ("spi: free
children in spi_unregister_master, not siblings") and broken again in
v2.6.37-rc1~2^2~4 during the merge of 2b9603a0 ("spi: enable
spi_board_info to be registered after spi_master").
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Lamparter <equinox@diac24.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When I added led_blink_set I had a typo: the return value of the hw
offload is a regular error code that is zero when succesful, and in that
case software emulation should not be used, rather than the other way
around.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Thomas Hellstrom <thomas@tungstengraphics.com>
Cc: Alan Hourihane <alanh@tungstengraphics.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Match the buffer size to the amount of initialized values. Before, it was
one too big and thus destroyed the neighbouring register causing the clock
to run at false speeds.
Reported-by: Andre van Rooyen <a.v.rooyen@sercom.nl>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If GPIO request succeeds, but configuration fails, it should be released.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some newer device revisions add a second parent ID. Support this in
the device validity checks done at startup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
We want to find the first set bit on value, not status.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Without this the IRQ base will not be correctly configured for the
subdevices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
rdc321x-wdt currently fetches its driver specific data by using the
platform_device->platform_data pointer, this is wrong because the mfd
device which registers our platform_device has been added using
mfd_add_device() which sets the platform_device->driver_data pointer
instead.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
rdc321x-gpio currently fetches its driver specific data by using the
platform_device->platform_data pointer, this is wrong because the mfd
device which registers our platform_device has been added using
mfd_add_device() which sets the platform_device->driver_data pointer
instead.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Always useful to know just which connector was polled and had its
status updated.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
We were using the lockup struct from the wrong union.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
n_gsm: gsm_data_alloc buffer allocation could fail and it is not being checked
n_gsm: Fix message length handling when building header
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
Revert "USB: gadget: Allow function access to device ID data during bind()"
USB: misc: uss720.c: add another vendor/product ID
USB: usb-storage: unusual_devs entry for the Samsung YP-CP3
USB: gadget: Remove suspended sysfs file before freeing cdev
USB: core: Add input prompt and help text for USB_OTG config
USB: ftdi_sio: Add D.O.Tec PID
xhci: Fix issue with port array setup and buggy hosts.
|
|
.. caused by a missing semi-colon, introduced in commit 0fc13c8995cd
("cciss: fix cciss_revalidate panic").
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Thiago Farina <tfransosi@gmail.com>
Cc: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On resume, we were attemping to unblank the displays before the
timing and plls had be reprogrammed which led to atom timeouts
waiting for things that are not yet programmed. Re-program
the mode first, then reset the dpms state.
This fixes the infamous atombios timeouts on resume.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This fixes module reloading and resume as the gfx block seems to
be left in a bad state in some cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Only reset the grbm blocks, srbm tends to lock the GPU
if not done properly and in most cases is not necessary.
Also, no need to call asic init after reset the grbm blocks.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This reverts commit 541cc966915b6756e54c20eebe60ae957afdb537.
Wei Yonjun reported this caused a regression against Intel VGA hotplug
on his G33 hw.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Without this, we attempt the handover too late, the firmware fb
might be accessing the chip simultaneously to us re-initializing
various parts of it, which might frighten babies or cause all sort
of nasty psychologic trauma to kitten.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[danvet: add cc: stable, forward ported and compile-fixed for X86]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[airlied: move to even earlier in module load.]
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] gspca - sonixj: Better handling of the bridge registers 0x01 and 0x17
[media] gspca - sonixj: Add the bit definitions of the bridge reg 0x01 and 0x17
[media] gspca - sonixj: Set the flag for some devices
[media] gspca - sonixj: Add a flag in the driver_info table
[media] gspca - sonixj: Fix a bad probe exchange
[media] gspca - sonixj: Move bridge init to sd start
[media] bttv: remove unneeded locking comments
[media] bttv: fix mutex use before init (BZ#24602)
[media] Don't export format_by_forcc on two different drivers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
clocksource: sh_cmt: Remove nested spinlock fix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6
* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
OMAP: OMAPFB: disable old omapfb for OMAP4 builds
OMAP: DSS: VRAM: Align start & size of vram to 2M
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cciss: fix cciss_revalidate panic
block: max hardware sectors limit wrapper
block: Deprecate QUEUE_FLAG_CLUSTER and use queue_limits instead
blk-throttle: Correct the placement of smp_rmb()
blk-throttle: Trim/adjust slice_end once a bio has been dispatched
block: check for proper length of iov entries earlier in blk_rq_map_user_iov()
drbd: fix for spin_lock_irqsave in endio callback
drbd: don't recvmsg with zero length
|
|
Its possible for the call to read rx timeout from the hardware to fail,
in which case we end up with a bogus rx timeout value. Set a default one
when filling in the rc struct, and we'll just overwrite it later w/the
value from hardware, but if that read fails, we've at least got a sane
rx timeout value to work with (1000ms is the default value I've seen
returned on most if not all mceusb hardware).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
As it turns out, somewhere along the way, we managed to invert the
meaning of the tx_mask_inverted flag. Looking back over the old lirc
driver, tx_mask_inverted was set to 0 if the device was in tx_mask_list.
Now we have a tx_mask_inverted flag set to 1 for all the devices that
were in the list, and set tx_mask_inverted to that flag value, which is
actually the opposite of what we used to set, causing set_tx_mask to use
the wrong mask setting option. Since there seem to be more devices with
inverted masks than not (using the original device as the baseline for
inverted vs. normal), lets just call the ones currently marked as
inverted normal instead, and flip the if/else actions that key off of
the inverted flag.
Note: the problem only cropped up if a call to set_tx_mask was made, if
no mask was set, the device would work just fine, which is why this
managed to slip though w/o getting noticed until now.
Tested successfully by myself and Dennis Gilmore.
Reported-by: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This makes several changes but they're in one function and sort of
related:
"buf" was leaked on error. The leak if we try to read an invalid
length is the main concern because it could be triggered over and
over.
If the copy_to_user() failed, then the original code returned the
number of bytes remaining. read() is supposed to be the opposite way,
where we return the number of bytes copied. I changed it to just return
-EFAULT on errors.
Also I changed the debug output from "-EFAULT" to just "<fail>" because
it isn't -EFAULT necessarily. And since we go though that path if the
length is invalid now, there was another debug print that I removed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
We shouldn't unlock here. I think this was a cut and paste error.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When trying to create persistent device names for mceusb and streamzap
devices, I noticed that their respective drivers are not creating the rc
device as a child of the USB device. Rather it creates it as virtual
device. As a result, udev cannot use the USB device information to
create persistent device names for event and lirc devices associated
with the rc device. Not having persistent device names makes it more
difficult to make use of the devices in userspace as their names can
change.
Signed-off-by: Paul Bender <pebender@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
There are cases where we get an ending space, and our trailing timeout
space then gets sent right after it, which breaks repeat, at least for
lirc userspace decoding. Merge the two spaces by way of using
ir_raw_event_store_filter, set a timeout value, and we're back to good.
Successfully tested with streamzap and windows mce remotes.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Something I failed to notice while testing the mceusb RLE buffer
decoding simplification patches was that we were getting an extra event
from the previously pressed key.
As was pointed out to me on irc by Maxim, this is actually due to using
ir_raw_event_store_with_filter without having set up a timeout value.
The hardware has a timeout value we're now reading and storing, which
properly enables the transition to idle in the raw event storage
process, and makes IR decode behave correctly w/o keybounce.
Also remove no-longer-used ir_raw_event struct from mceusb_dev struct
and add as-yet-unused enable flags for carrier reports and learning
mode, which I'll hopefully start wiring up sooner than later. While
looking into that, found evidence that 0x9f 0x15 responses are only
non-zero when the short-range learning sensor is used, so correct the
debug spew message, and then suppress it when using the standard
long-range sensor.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
And clean up some stray spaces.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
If we pass in an offset, we shouldn't skip 2 bytes. And the first-gen
hardware generates a constant stream of interrupts, always with two
header bytes, and if there's been no IR, with nothing else. Bail from
ir processing without calling ir_handle_raw_event when we get such a
buffer delivered to us.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
We were storing a bunch of spaces at the end of each signal, rather than
a single long space. The in-kernel decoders were actually okay with
this, but lirc isn't. As suggested by David Härdeman, switch to storing
samples using ir_raw_event_store_with_filter, which auto-merges the
consecutive space samples for us. This also allows us to bypass having
to store rawir samples in our device struct, further simplifying the
buffer parsing state machine. Both in-kernel decoders and lirc are happy
again with this change.
Also included in this patch is proper parsing of 0x9f 0x01 commands, the
removal of some magic number usage and some printk spew fixups.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Rather than waiting for trigger bits, the formula for which was slightly
messy, and apparently, not actually 100% complete for some remotes, just
call ir_raw_event_handle whenever we finish parsing a chunk of data from
the rx fifo, similar to mceusb, as well as whenever we see an 'end of
signal data' 0x80 packet.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Another multi-function Conexant device. Interface 0 is IR, though on
this model, TX isn't wired up at all, so I've mixed in support for
models without TX (and verified that lircd says TX isn't supported when
trying to send w/this device).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
FIMC IP in S5Pv310 series has extended DMA status registers
and some bit fields are marked as reserved comparing to S5PC100/110.
Use correct registers for getting DMA write pointer in each SoC variant
supported by the driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Replace V4L2_PIX_FMT_RGB24 code with V4L2_PIX_FMT_RGB32
since the hardware uses 24-bits for actual pixel data but pixels
are 4-byte aligned in memory.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Reported by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Create separate vidioc_g_crop/vidioc_s_crop handlers for capture
video node and so image cropping parameters are properly queried
at FIMC input (image sensor) and not at FIMC output.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Adapt to recent videobuf_queue_dma_contig_init signature change.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The test for driver->owner != NULL in sh_mobile_ceu_camera.c is unneeded and it
breaks the static build of sh_mobile_csi2.c. Remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When SOCAM_PCLK_SAMPLE_FALLING, just leave CSICR1_REDGE unset, otherwise we get
the inverted behaviour.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
