Age | Commit message (Collapse) | Author |
|
Add a read/write rfkill interface to the bluetooth radio switch on the
bluetooth submodule, and one for the wireless wan radio switch to the wan
submodule.
Since rfkill does care for when a switch changes state, use WLSW
notifications to also check if the WWAN or Bluetooth switches did not
change state (due to them being slaves of WLSW in firmware/hardware, but
that reality not being always properly exported by the thinkpad firmware).
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
|
|
On ThinkPads where the WLSW switch exists, the firmware or the hardware
ANDs the WLSW state with the device-specific switches (WWAN, Bluetooth).
It is downright impossible to enable WWAN or Bluetooth when WLSW is
blocking the radios.
This reality does not necessarily carry over to the WWAN and Bluetooth
firmware interfaces, though... so the state thinkpad-acpi was reporting
could be incorrect.
Tie the three switches in the driver so that we keep their state sane.
When WLSL is off, force the other switches to off as well.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
|
|
Get rid of some forward definitions by moving code around, this will make
the rfkill conversion of wwan and bluetooth a bit cleaner.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
|
|
Rename tpacpi_input_send_radiosw() to tpacpi_send_radiosw_update(), and
make it a central point to issue "radio switch changed state" notifications
by consolidating also the poll() notification in the same function.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
|
|
Change the code of hotkey_init, wan_init and bluetooth_init a bit to make it
much easier to add some Kconfig-selected debugging code later.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
gpu: re-order GPU subdirectory vs char for AGP vs DRM startup.
|
|
* 'for-linus' of git://git.o-hand.com/linux-mfd:
mfd: let asic3 use mem resource instead of bus_shift
mfd: remove DS1WM register definitions from asic3.h
mfd: add ASIC3_CONFIG_GPIO templates
mfd: fix the asic3 irq demux code
mfd: asic3 should depend on gpiolib
mfd: fix asic3 config array initialisation
mfd: move asic3 probe functions into __init section
mfd: Use uppercase only for asic3 macros and defines
mfd: use dev_* macros for asic3 debugging
mfd: New asic3 gpio configuration code
mfd: asic3 children platform data removal
mfd: asic3 gpiolib support
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (277 commits)
V4L/DVB (8415): gspca: Infinite loop in i2c_w() of etoms.
V4L/DVB (8414): videodev/cx18: fix get_index bug and error-handling lock-ups
V4L/DVB (8411): videobuf-dma-contig.c: fix 64-bit build for pre-2.6.24 kernels
V4L/DVB (8410): sh_mobile_ceu_camera: fix 64-bit compiler warnings
V4L/DVB (8397): video: convert select VIDEO_ZORAN_ZR36060 into depends on
V4L/DVB (8396): video: Fix Kbuild dependency for VIDEO_IR_I2C
V4L/DVB (8395): saa7134: Fix Kbuild dependency of ir-kbd-i2c
V4L/DVB (8394): ir-common: CodingStyle fix: move EXPORT_SYMBOL_GPL to their proper places
V4L/DVB (8393): media/video: Fix depencencies for VIDEOBUF
V4L/DVB (8392): media/Kconfig: Convert V4L1_COMPAT select into "depends on"
V4L/DVB (8390): videodev: add comment and remove magic number.
V4L/DVB (8389): videodev: simplify get_index()
V4L/DVB (8387): Some cosmetic changes
V4L/DVB (8381): ov7670: fix compile warnings
V4L/DVB (8380): saa7115: use saa7115_auto instead of saa711x as the autodetect driver name.
V4L/DVB (8379): saa7127: Make device detection optional
V4L/DVB (8378): cx18: move cx18_av_vbi_setup to av-core.c and rename to cx18_av_std_setup
V4L/DVB (8377): ivtv/cx18: ensure the default control values are correct
V4L/DVB (8376): cx25840: move cx25840_vbi_setup to core.c and rename to cx25840_std_setup
V4L/DVB (8374): gspca: No conflict of 0c45:6011 with the sn9c102 driver.
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (1232 commits)
iucv: Fix bad merging.
net_sched: Add size table for qdiscs
net_sched: Add accessor function for packet length for qdiscs
net_sched: Add qdisc_enqueue wrapper
highmem: Export totalhigh_pages.
ipv6 mcast: Omit redundant address family checks in ip6_mc_source().
net: Use standard structures for generic socket address structures.
ipv6 netns: Make several "global" sysctl variables namespace aware.
netns: Use net_eq() to compare net-namespaces for optimization.
ipv6: remove unused macros from net/ipv6.h
ipv6: remove unused parameter from ip6_ra_control
tcp: fix kernel panic with listening_get_next
tcp: Remove redundant checks when setting eff_sacks
tcp: options clean up
tcp: Fix MD5 signatures for non-linear skbs
sctp: Update sctp global memory limit allocations.
sctp: remove unnecessary byteshifting, calculate directly in big-endian
sctp: Allow only 1 listening socket with SO_REUSEADDR
sctp: Do not leak memory on multiple listen() calls
sctp: Support ipv6only AF_INET6 sockets.
...
|
|
dio_bus_match() can use dio_match_device().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Looking at older kernel sources the APOLLO_ELPLUS option was added
somewhere during kernel 2.1, but even kernel 2.2.0 does not contain
any driver that would be enabled through it...
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes the following build error:
<-- snip -->
..
Building modules, stage 2.
MODPOST 1203 modules
ERROR: "c2p" [drivers/video/amifb.ko] undefined!
..
make[2]: *** [__modpost] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds the missing MODULE_LICENSE("GPL").
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Register the Atari-specific video modes with sysfs, so you can see them in
/sys/class/graphics/fb0/modes and change the video mode by writing to
/sys/class/graphics/fb0/mode.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Register the Amiga-specific video modes with sysfs, so you can see them in
/sys/class/graphics/fb0/modes and change the video mode by writing to
/sys/class/graphics/fb0/mode.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
zorro: use memory_read_from_buffer
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ZORRO: Replace deprecated __initcall with equivalent device_initcall.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
According to the tests in do_initcalls(), the proper error code in case no
device is found is -ENODEV, not -ENXIO or -EIO.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use net_device_stats from net_device structure instead of local.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://oss.oracle.com/git/jlbec/linux-2.6
* 'configfs-fixup-ptr-error' of git://oss.oracle.com/git/jlbec/linux-2.6:
configfs: Allow ->make_item() and ->make_group() to return detailed errors.
Revert "configfs: Allow ->make_item() and ->make_group() to return detailed errors."
|
|
commit d1857056904d5f313f11184fcfa624652ff9620a ("ACPI: don't walk
tables if ACPI was disabled") is another superfluous duplicate commit
caused by git -> quilt -> git conversion.
Revert it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit 816c2eda3ce8fa7eb62f22e01e2ec7a3f7d677c0 ("dock: bay: Don't call
acpi_walk_namespace() when ACPI is disabled.") was merged between
2.6.26-rc8 and -rc9)
Due to rebasing the ACPI tree via quilt the same patch got applied again
via commit cc7e51666d82aedfd6b9a033ca1a10d71c21f1ca ("dock: bay: Don't
call acpi_walk_namespace() when ACPI is disabled.")
Revert it, as it is obviously bogus.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move more bits into the tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch cyclades to use the new tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Reverse the order of one test and it gets much more readable
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch the synclink ports to use the new tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch the stallion driver to use the tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The tty pointer has been moved into a tty_port field, so we need to use
->info->port.tty instead of just ->info->tty. Fixes these build errors:
David Brownell <david-b@pacbell.net> wrote:
> drivers/serial/atmel_serial.c: In function 'atmel_rx_from_ring':
> drivers/serial/atmel_serial.c:665: error: 'struct uart_info' has no member named 'tty'
> drivers/serial/atmel_serial.c: In function 'atmel_rx_from_dma':
> drivers/serial/atmel_serial.c:672: error: 'struct uart_info' has no member named 'tty'
> drivers/serial/atmel_serial.c: In function 'atmel_startup':
> drivers/serial/atmel_serial.c:797: error: 'struct uart_info' has no member named 'tty'
> make[2]: *** [drivers/serial/atmel_serial.o] Error 1
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch the rocketport to use the new tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch mxser to use the new tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch MOXA to use the new tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch istallion to use the new tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch isicom to use a tty_port structure for some fields
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Chris Malley posted a patch removing a NULL check in the riscom8 driver.
Further analysis shows that even more of the tests are irrelevant so we
can delete lots of stuff
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch riscom8 to use the new tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch drivers using the old "generic serial" driver to use the tty_port
structures
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch esp to use the new tty_port structures
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch the EPCA driver to include and begin using a tty_port structure
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The below is the patch to replace blindly all possible places,
including Jack's fixes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
(Reviewed and checked rather than blindly added)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix compile errors in SGI console drivers caused by changes to the
tty_port structures in the linux-next tree.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Today's linux-next build (powerpc allyesconfig) failed like this:
drivers/serial/pmac_zilog.c: In function 'pmz_receive_chars':
drivers/serial/pmac_zilog.c:245: error: 'struct uart_info' has no member named 'tty'
drivers/serial/pmac_zilog.c:250: error: 'struct uart_info' has no member named 'tty'
I applied the patch below (which builds but may, or may not, be correct).
--
Cheers,
Stephen Rothwell sfr@canb.auug.org.au
http://www.canb.auug.org.au/~sfr/
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Today's linux-next build (sparc64 defconfig) failed like this:
drivers/serial/sunhv.c: In function `receive_chars':
drivers/serial/sunhv.c:188: error: structure has no member named `tty'
drivers/serial/sunsu.c: In function `receive_chars':
drivers/serial/sunsu.c:314: error: structure has no member named `tty'
drivers/serial/sunsab.c: In function `receive_chars':
drivers/serial/sunsab.c:121: error: structure has no member named `tty'
I applied the following patch (which, again, may not be correct).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch the serial_core based drivers to use the new tty_port structure.
We can't quite use all of it yet because of the dynamically allocated
extras in the serial_core layer.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Every tty driver has its own concept of a port structure and because
they all differ we cannot extract commonality. Begin fixing this by
creating a structure drivers can elect to use so that over time we can
push fields into this and create commonality and then introduce common
methods.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch removes CVS keywords that weren't updated for a long time in
comments, printk's and MODULE_DESCRIPTION's (no printk's or
MODULE_DESCRIPTION's are completely removed).
While doing this I also found and fixed a missing \n in a printk
in m32r_sio.c
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch removes ancient VCS tags (either protected
by #ifdef SCCS_LABELS or commented out).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move the line disciplines towards a conventional ->ops arrangement. For
the moment the actual 'tty_ldisc' struct in the tty is kept as part of
the tty struct but this can then be changed if it turns out that when it
all settles down we want to refcount ldiscs separately to the tty.
Pull the ldisc code out of /proc and put it with our ldisc code.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Don't forget to enable and disable PCI devices. The device might be
unusable without that.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|