| Age | Commit message (Collapse) | Author |
|---|
|
Use PCI_VENDOR_ID_INTEL from pci_ids.h instead of creating its own
vendor ID #define.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use PCI_VENDOR_ID_INTEL from pci_ids.h instead of creating its own
vendor ID #define.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc Kleine-Budde says:
====================
the fifth pull request for upcoming v3.6 net-next cleans up and
improves the janz-ican3 driver (6 patches by Ira W. Snyder, one by me).
A patch by Steffen Trumtrar adds imx53 support to the flexcan driver.
And another patch by me, which marks the bit timing constant in the CAN
drivers as "const".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
The Janz VMOD-ICAN3 hardware has support for one shot packet
transmission. This means that a packet will be attempted to be sent
once, with no automatic retries.
The SocketCAN core has a controller-wide setting for this mode:
CAN_CTRLMODE_ONE_SHOT. The Janz VMOD-ICAN3 hardware supports this flag
on a per-packet level, but the SocketCAN core does not.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If the bus error quota is set to infinite and the host CPU cannot keep
up, the Janz VMOD-ICAN3 firmware will stop responding to control
messages until the controller is reset.
The firmware will automatically stop sending bus error messages when the
quota is reached, and will only resume sending bus error messages when
the quota is re-set to a positive value.
This limitation is worked around by setting the bus error quota to one
message, and then re-setting the quota to one message every time a bus
error message is received. By doing this, the firmware never stops
responding to control messages. The CAN bus can be reset without a
hard-reset of the controller card.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The Janz VMOD-ICAN3 firmware does not support any sort of TX-done
notification or interrupt. The driver previously used the hardware
loopback to attempt to work around this deficiency, but this caused all
sockets to receive all messages, even if CAN_RAW_RECV_OWN_MSGS is off.
Using the new function ican3_cmp_echo_skb(), we can drop the loopback
messages and return the original skbs. This fixes the issues with
CAN_RAW_RECV_OWN_MSGS.
A private skb queue is used to store the echo skbs. This avoids the need
for any index management.
Due to a lack of TX-error interrupts, bus errors are permanently
enabled, and are used as a TX-error notification. This is used to drop
an echo skb when transmission fails. Bus error packets are not generated
if the user has not enabled bus error reporting.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The error and byte counter statistics were being incremented
incorrectly. For example, a TX error would be counted both in tx_errors
and rx_errors.
This corrects the problem so that tx_errors and rx_errors are only
incremented for errors caused by packets sent to the bus. Error packets
generated by the driver are not counted.
The byte counters are only increased for packets which are actually
transmitted or received from the bus. Error packets generated by the
driver are not counted.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch cleans up the ICAN3 to Linux CAN frame and vice versa
conversion functions:
- RX: Use get_can_dlc() to limit the dlc value.
- RX+TX: Don't copy the whole frame, only copy the amount of bytes
specified in cf->can_dlc.
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
Tested-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The commit which added the janz-ican3 driver and commit
3ccd4c61 "can: Unify droping of invalid tx skbs and netdev stats" were
committed into mainline Linux during the same merge window.
Therefore, the addition of this code to the janz-ican3 driver was
forgotten. This patch adds the expected code.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The code which used this variable was removed during review, before the
driver was added to mainline Linux. It is now dead code, and can be
removed.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds support for a second clock to the flexcan driver. On
modern freescale ARM cores like the imx53 and imx6q two clocks ("ipg"
and "per") must be enabled in order to access the CAN core.
In the original driver, the clock was requested without specifying the
connection id, further all mainline ARM archs with flexcan support
(imx28, imx25, imx35) register their flexcan clock without a
connection id, too.
This patch first renames the existing clk variable to clk_ipg and
converts it to devm for easier error handling. The connection id "ipg"
is added to the devm_clk_get() call. Then a second clock "per" is
requested. As all archs don't specify a connection id, both clk_get
return the same clock. This ensures compatibility to existing flexcan
support and adds support for imx53 at the same time.
After this patch hits mainline, the archs may give their existing
flexcan clock the "ipg" connection id and implement a dummy "per"
clock.
This patch has been tested on imx28 (unmodified clk tree) and on imx53
with a seperate "ipg" and "per" clock.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch marks the bittiming_const pointer as in the struct can_pric as
"const". This allows us to mark the struct can_bittiming_const in the CAN
drivers as "const", too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
|
|
Conflicts:
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c
|
|
In its receive path, mlx4_en driver maps each page chunk that it pushes
to the hardware and unmaps it when pushing it up the stack. This limits
throughput to about 3Gbps on a Power7 8-core machine.
One solution is to map the entire allocated page at once. However, this
requires that we keep track of every page fragment we give to a
descriptor. We also need to work with the discipline that all fragments will
be released (in the sense that it will not be reused by the driver
anymore) in the order they are allocated to the driver.
This requires that we don't reuse any fragments, every single one of
them must be reallocated. We do that by releasing all the fragments that
are processed and only after finished processing the descriptors, we
start the refill.
We also must somehow guarantee that we either refill all fragments in a
descriptor or none at all, without resorting to giving up a page
fragment that we would have already given. Otherwise, we would break the
discipline of only releasing the fragments in the order they were
allocated.
This has passed page allocation fault injections (restricted to the
driver by using required-start and required-end) and device hotplug
while 16 TCP streams were able to deliver more than 9Gbps.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dynamically allocated sysfs attributes must be initialized using
sysfs_attr_init(), otherwise lockdep complains:
BUG: key <address> not in .data!
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 9ac32e1b firmware: convert e100 driver to request_firmware()
did a straight conversion of the in-driver ucode to external
files. This introduced the possibility of the driver failing
to enable an interface due to missing ucode. There was no
evaluation of the importance of the ucode at the time.
Based on comments in earlier versions of this driver, and in
the source code for the FreeBSD fxp driver, we can assume that
the ucode implements the "CPU Cycle Saver" feature on supported
adapters. Although generally wanted, this is an optional
feature. The ucode source is not available, preventing it from
being included in free distributions. This creates unnecessary
problems for the end users. Doing a network install based on a
free distribution installer requires the user to download and
insert the ucode into the installer.
Making the ucode optional when possible improves the user
experience and driver usability.
The ucode for some adapters include a bugfix, making it
essential. We continue to fail for these adapters unless the
ucode is available.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 16626b0cc3d5afe250850f96759b241f8a403b52 the asix
driver depends on the phylib. Select phylib when the asix driver is
selected.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: kernel-janitors@vger.kernel.org
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the asix_set_eeprom() function to provide support for
programming the configuration EEPROM via ethtool.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code for reading the EEPROM via ethtool in the asix
driver has a few issues. It cannot handle odd length values
(accesses must be aligned at 16 bit boundaries) and interprets the
offset provided by ethtool as 16 bit word offset instead as byte offset.
The new code for asix_get_eeprom() introduced by this patch is
modeled after the code in
drivers/net/ethernet/atheros/atl1e/atl1e_ethtool.c
and provides read access to the entire EEPROM with arbitrary
offsets and lengths.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because there are multiple variants to the stmmac/dwmac driver, the
dts bindings should be updated to include version of the IP used.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cxgb3 interface has a bad performance when VLAN is set. On my current
setup, a PowerLinux 7R2, I am able to get around 7 Gbps on a TCP_STREAM
(8 instances, 4k message).
With this patch, I am able to reach 9.5 Gbps.
Signed-off-by: Breno Leitao <brenohl@br.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Duan Jiong <djduanjiong@gmail.com>
|
|
Use RFS infrastructure and flow steering in HW to keep CPU
affinity of rx interrupts and application per TCP stream.
A flow steering filter is added to the HW whenever the RFS
ndo callback is invoked by core networking code.
Because the invocation takes place in interrupt context, the
actual setup of HW is done using workqueue. Whenever new filter
is added, the driver checks for expiry of existing filters.
Since there's window in time between the point where the core
RFS code invoked the ndo callback, to the point where the HW
is configured from the workqueue context, the 2nd, 3rd etc
packets from that stream will cause the net core to invoke
the callback again and again.
To prevent inefficient/double configuration of the HW, the filters
are kept in a database which is indexed using hash function to enable
fast access.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable callers of mlx4_assign_eq to supply a pointer to cpu_rmap.
If supplied, the assigned IRQ is tracked using rmap infrastructure.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define this macro is one common place instead of duplicating it over the code
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull three md bugfixes from NeilBrown:
"One of the bugs was introduced in 3.5-rc1. Others have been there for
longer."
* tag 'md-3.5-fixes' of git://neil.brown.name/md:
md/raid1: close some possible races on write errors during resync
md: avoid crash when stopping md array races with closing other open fds.
md: fix bug in handling of new_data_offset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID update from Jiri Kosina:
"A final round of changes for HID for 3.5: just device ID additions."
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: hid-multitouch: add support for Zytronic panels
HID: add Sennheiser BTD500USB device support
HID: add battery quirk for Apple Wireless ANSI
|
|
The strcpy was being used to set the name of the board. Since the
destination char* was read-only and the name is set statically at
compile time; this was both wrong and redundant.
The type of char* is changed to const char* to prevent future errors.
Reported-by: Radek Masin <radek@masin.eu>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
[ Taking directly due to vacations - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
commit 4367af556133723d0f443e14ca8170d9447317cb
md/raid1: clear bad-block record when write succeeds.
Added a 'reschedule_retry' call possibility at the end of
end_sync_write, but didn't add matching code at the end of
sync_request_write. So if the writes complete very quickly, or
scheduling makes it seem that way, then we can miss rescheduling
the request and the resync could hang.
Also commit 73d5c38a9536142e062c35997b044e89166e063b
md: avoid races when stopping resync.
Fix a race condition in this same code in end_sync_write but didn't
make the change in sync_request_write.
This patch updates sync_request_write to fix both of those.
Patch is suitable for 3.1 and later kernels.
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Original-version-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
md will refuse to stop an array if any other fd (or mounted fs) is
using it.
When any fs is unmounted of when the last open fd is closed all
pending IO will be flushed (e.g. sync_blockdev call in __blkdev_put)
so there will be no pending IO to worry about when the array is
stopped.
However in order to send the STOP_ARRAY ioctl to stop the array one
must first get and open fd on the block device.
If some fd is being used to write to the block device and it is closed
after mdadm open the block device, but before mdadm issues the
STOP_ARRAY ioctl, then there will be no last-close on the md device so
__blkdev_put will not call sync_blockdev.
If this happens, then IO can still be in-flight while md tears down
the array and bad things can happen (use-after-free and subsequent
havoc).
So in the case where do_md_stop is being called from an open file
descriptor, call sync_block after taking the mutex to ensure there
will be no new openers.
This is needed when setting a read-write device to read-only too.
Cc: stable@vger.kernel.org
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
commit c6563a8c38fde3c1c7fc925a10bde3ca20799301
md: add possibility to change data-offset for devices.
introduced a 'new_data_offset' attribute which should normally
be the same as 'data_offset', but can be explicitly set to a different
value to allow a reshape operation to move the data.
Unfortunately when the 'data_offset' is explicitly set through
sysfs, the new_data_offset is not also set, so the two would become
out-of-sync incorrectly.
One result of this is that trying to set the 'size' after the
'data_offset' would fail because it is not permitted to set the size
when the 'data_offset' and 'new_data_offset' are different - as that
can be confusing.
Consequently when mdadm tried to do this while assembling an IMSM
array it would fail.
This bug was introduced in 3.5-rc1.
Reported-by: Brian Downing <bdowning@lavos.net>
Bisected-by: Brian Downing <bdowning@lavos.net>
Tested-by: Brian Downing <bdowning@lavos.net>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Pull target fixes from Nicholas Bellinger:
"This includes a bugfix from MDR to address a NULL pointer OOPs with
FCoE aborts, along with a WRITE_SAME emulation bugfix for NOLB=0
cases, and persistent reservation return cleanups from Roland.
All three patches are CC'ed to stable."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix range calculation in WRITE SAME emulation when num blocks == 0
target: Clean up returning errors in PR handling code
tcm_fc: Fix crash seen with aborts and large reads
|
|
Commit a7a20d103994 ("sd: limit the scope of the async probe domain")
make the SCSI device probing run device discovery in it's own async
domain.
However, as a result, the partition detection was no longer synchronized
by async_synchronize_full() (which, despite the name, only synchronizes
the global async space, not all of them). Which in turn meant that
"wait_for_device_probe()" would not wait for the SCSI partitions to be
parsed.
And "wait_for_device_probe()" was what the boot time init code relied on
for mounting the root filesystem.
Now, most people never noticed this, because not only is it
timing-dependent, but modern distributions all use initrd. So the root
filesystem isn't actually on a disk at all. And then before they
actually mount the final disk filesystem, they will have loaded the
scsi-wait-scan module, which not only does the expected
wait_for_device_probe(), but also does scsi_complete_async_scans().
[ Side note: scsi_complete_async_scans() had also been partially broken,
but that was fixed in commit 43a8d39d0137 ("fix async probe
regression"), so that same commit a7a20d103994 had actually broken
setups even if you used scsi-wait-scan explicitly ]
Solve this problem by just moving the scsi_complete_async_scans() call
into wait_for_device_probe(). Everybody who wants to wait for device
probing to finish really wants the SCSI probing to complete, so there's
no reason not to do this.
So now "wait_for_device_probe()" really does what the name implies, and
properly waits for device probing to finish. This also removes the now
unnecessary extra calls to scsi_complete_async_scans().
Reported-and-tested-by: Artem S. Tashkinov <t.artem@mailcity.com>
Cc: Dan Williams <dan.j.williams@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <jbottomley@parallels.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: linux-scsi <linux-scsi@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This change is just meant to defragment the flags as there are several hole
that have been introduced since several features, or the flags for them,
have been removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
All of our hardware supports RSS even if it is only for a single queue. So
instead of toting around the RSS enable flag I am updating the code so that
all devices are enabled and if we want to disable RSS it is indicated via
the RSS mask.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change essentially makes it so that we can enable almost all of the
features all at once. This patch allows for the combination of SR-IOV,
DCB, and FCoE in the case of the x540. It also beefs up the SR-IOV by
adding support for RSS to the PF.
The testing matrix gets to be very complex for this patch as there are a
number of different features and subsets for queueing options. I tried to
narrow these down a bit by restricting the PF to only supporting 4TC DCB
when it is enabled in addition to SR-IOV.
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change allows all pools from the default pool forward to be enabled vi
ixgbe_configure_virtualization. This is needed as we are planning to use
queues belonging to adjacent pools for FCoE when SR-IOV and FCoE are both
enabled.
In addition this patch contains some minor formatting changes as there were
a few spots that seemed to be in need of some cleanup.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In ixgbevf_get_ringparam we could run into a NULL pointer dereference
if the rings were not allocated when we attempted the call. To prevent
that we can just access the tx/rx_ring_count values instead of attempting
to access the rings to get the count.
This change corrects a memory leak and memory corruption in
ixgbevf_set_ringparam.
The memory leak was due to us not freeing the resources from the ring
before overwriting them. This change corrects the memory leak by making
certain to call ixgbe_free_tx/rx_resources on the rings prior to freeing
them.
The memory corruption was because we were replacing the rings but not
updating the q_vectors. It addresses the memory corruption by leaving the
rings in place and instead just copying the contents of the new rings into
the existing rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There is a good bit of redundancy between the Tx checksum and segmentation
offloads. In order to reduce some of this I am moving the code for
creating a context descriptor into a separate function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change adds the netdev to the ring structure. This allows for a
quicker transition from ring to netdev without having to go from ring to
adapter to netdev.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The driver is going back one step from its' previous location before
bumping tail. This is incorrect. We should just be writing the value of
next_to_use into the tail register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We have had an issue when using ixgbe+ixgbevf and 802.1 VLAN tagging.
When attaching a VLAN to a VF, frames with a 802.1q priority appeared
untagged on the VF hence not reaching the VLAN, where frames with
priority 0 where tagged as expected and seen by the VLAN device.
This seems due to the way ixgbevf is looking up the full tag
(prio+cfi+vlan) against the adapter active_vlans, as a condition to mark
the skb tagged.
Signed-off-by: Pascal Bouchareine <pascal@gandi.net>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
The original driver implementation assumed that for TSO, all the
payload data would be in the frags. This isn't always true; change
the driver to support payload data at skb->data between
"skb_transport_offset(skb) + tcp_hdrlen(skb)" and "skb->hdr_len",
followed by the data in the frags.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
Avoid packets belonging to queue/cpu A trying to transmit on cpu B.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
|
|
Cloned patch of Eric Dumazet for bonding.
Some workloads greatly benefit of IFF_XMIT_DST_RELEASE capability
on output net device, avoiding dirtying dst refcount.
team currently disables IFF_XMIT_DST_RELEASE unconditionally.
If all ports have the IFF_XMIT_DST_RELEASE bit set, then
team dev can also have it in its priv_flags.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
