| Age | Commit message (Collapse) | Author |
|---|
|
Use managed resources for the mmio memory region and the clock.
Makes the code a bit shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Use the slot-gpio helpers to handle the write protect and card detect
GPIO pins instead of re-implementing the same functionality in the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
It's a bit shorter than open-conding it. While we are at it also make
jz4740_mmc_pm_ops static.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
For no reason, the code handling write errors was implemented while
the code handling read errors was missing.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The following error randomly appears on an imx6q board where gpio is
used to implement card-detection when mounting EXT4 rootfs during boot.
mmc1: Card removed during transfer!
mmc1: Resetting controller.
mmcblk0: unknown error -123 sending read/write command, card status 0x900
end_request: I/O error, dev mmcblk0, sector 106744
EXT4-fs error (device mmcblk0p2): ext4_find_entry:1312: inode #5011: comm swapper/0: reading directory lblock 0
It turns out that the error message comes from the card removal check
in function sdhci_card_event(). While we have a well implemented
function sdhci_do_get_cd() handling all the possible cases of
CD, the current code only checks controller internal CD case. That
causes problem for other CD cases like gpio on above imx6q board.
Improve the check by using sdhci_do_get_cd() to cover all possible CD
cases, so that above error on the imx6q board gets fixed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
As of now we rely on code outside of the driver to set the ciu clock
frequency. There's no reason to do that. Add support for setting up
the clock in the driver during probe.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
It is possible to specify a regulator that should be turned on when
dw_mmc is probed. At the moment dw_mmc will fail to use the regulator
properly if the regulator probes after dw_mmc. Fix this problem by
honoring EPROBE_DEFER.
At the same time move the regulator code out of the slot init code.
We only specify one regulator for the whole device and other parts of
the code (like suspend/resume) assume that the regulator has only been
enabled once.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
In order to make it possible to reduce the SD bus frequency,
parse the optional "max-frequency" attribute as documented in
devicetree/bindings/mmc/mmc.txt
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The SDCLK is divided down from the host controller clock. Host
controller clock may be different from the maximum SDCLK, so
get it from the platform, instead of just using the max SDCLK.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Inside the routine mmc_blk_ioctl_cmd() the sanitize command is
identified according to the value of bits 16-23 of the argument.
but what happens if a different command is sent, and only by
chance, bits 16-23 contain the value of SANITIZE command ?
In that case a SANITIZE command will be falsely identified.
In order to prevent such a case, the condition is expanded and
now it also checks the opcode itself, and verifies that it is an
MMC_SWITCH opcode.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Header file not needed anymore as we have removed the calls to
cpu_is_xxx() macro.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The PCI driver is getting simplier and tidier with pcim_* and devm_*
functions in use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
In few places usage of ret variable is not needed.
This patch simplifies those pieces of code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
devm_ioremap_resource does sanity checks on the given resource.
No need to duplicate this in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
We had a multi-partition SD-Card with two ext2 file systems. The partition
table was getting overwritten by a race between the card removal and
the unmount of the 2nd ext2 partition.
What was observed:
1. Suspend/resume would call to remove the device. The clearing
of the device information is done asynchronously.
2. A request is made to unmount the file system (this is called
after the removal has started).
3. The remapping table was cleared by the asynchronous part of
the device removal.
4. A write request to the super block (block 0 of the partition)
was sent down and instead of being remapped to the partition
offset, it was remapped to block 0 of the device which is where
the partition table is located.
5. Write was queued and written resulting in the overwriting
of the partition table with the ext2 super block.
6. The mmc_queue is cleaned up.
The mmc card device driver used to access SD cards, was calling del_gendisk
before calling mmc_cleanup-queue. The comment in the mmc_blk_remove_req
code indicated that it expected del_gendisk to block all further requests
from being queued but it doesn't. The mmc driver uses the presences of the
mmc_queue to determine if the request should be queued.
The fix was to clean up the mmc_queue before the rest of the
the delete partition code is called.
This prevents the overwriting of the partition table.
However, the umount gets an error trying to write the super block.
The umount should be issued before the device is removed but that
is not always possible. The umount is still needed to cleanup other
data structures.
Addresses the problem described in http://crbug.com/240815
Signed-off-by: Paul Taysom <taysom@chromium.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Patch "mmc: sdhci: Add size for caller in init+register" changed the
interface for sdhci_pltfm_init, while patch "mmc: sdhci-sirf: add mmc
host sdhci-pltfm based driver for SiRF SoCs" added a new driver
with the old interface.
This changes the sirf driver to use the new interface, avoiding
one warning, and simplifying the init sequence. Since we're here
already, this also adds an error path for failed clk_prepare_enable.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christian Daudt <csd@broadcom.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Fix to return a negative error code instead of 0 when we cannot get
IRQ source by platform_get_irq(), as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Fix to return a negative error code in the gpio_to_irq() error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
At Interrupt status register, Bit9 is Data Read Timeout.
But we used macro name as the DTO. It could be confused with the
Data Transfer Over(DTO)-Bit[3].
It's clearly that is changed the DRTO instead of DTO.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Since commit ab78029 (drivers/pinctrl: grab default handles from
device core), we can rely on device core for handling pinctrl.
So remove devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
With the new eMMC5.1 spec, there is a new EXT_CSD register with
the revision number(EXT_CSD_REV) 7. This patch updates the check
for ext-csd.rev number as 7.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
With device core now able to setup the default pin configuration, the
call to devm_pinctrl_get_select_default can be removed. And the pin
configuration code based on the deprecated Samsung specific gpio
bindings is also removed.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Instead of parsing the DT binding on our own, use the standard parser
mmc_of_parse(), introduced by commit 6c56e7a.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
In addition to just logging errors encountered during DT parsing or
allocating GPIO slots for CD/WP, mmc_of_parse() now returns with an error.
In particular, this is needed if the GPIO allocation may return
EPROBE_DEFER.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
In preparation to switching the jz4740 clk driver to the
common clk framework, update the clk enable/disable calls
to clk_prepare_enable/clk_disable_unprepare.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This fixes two reported problems:
1. after a system resume the controller isn't functioning until a command
runs on a timeout and a controller reset is performed.
2. if a card is ejected during a running write operation, its re-insertion
isn't detected.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Reported-by: Nguyen Hong Ky <nh-ky@jinso.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Tested-by: Nguyen Hong Ky <nh-ky@jinso.co.jp>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
With MMC clock gating enabled the MMC core currently calls MMC host driver's
.set_ios() method with .power_mode == MMC_POWER_ON and the clock value set
either to 0 or to the target rate. The tmio MMC driver then wrongly
translates the latter calls to card slot power-on requests, even when the
slot already was on. This patch fixes the driver to avoid needlessly
incrementing power-supplying regulator's use count.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Masking events on MMCIF means that an occurrence of the masked event
won't raise an interrupt, but the event bit will still be set in the
interrupt status register. If simultaneously a different event occurs
which was enabled, both flags will be set. However, only the unmasked
event bit should be cleared in the status register in such a case.
Clearing also the masked bit can lead to lost interrupts, which indeed
can be observed on the armadillo800eva r8a7740 board with an eMMC chip.
The problem has been introduced by the recent "mmc: sh_mmcif: simplify
IRQ processing" patch. Fix the problem by only clearing enabled interrupts.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
When resuming, the tmio_mmc_host_resume() function is run when the
controller might still be powered down. Issuing a reset command to it at
that time has no effect. This patch postpones resetting the controller
until the first powering-up .set_ios() call.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add a param to allow users of sdhci_pltfm to allocate private space
in calls to sdhci_pltfm_init+sdhci_pltfm_register. This is implemented
in the same way as sdhci does for its users.
None of the users have been migrated yet and are passing in zero to
retain their private allocation.
- todo: migrate clients to using allocation this way
- todo: remove priv variable once migration is complete
Also removed unused variable in sdhci_pltfm_init fn
Signed-off-by: Christian Daudt <csd@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add support for runtime PM for BYT SD cards.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Enable runtime PM for ACPI HID 80860F14 SD cards, adding support for
card detect GPIO.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
If card power is dependent on SD bus power then the host controller
must not be runtime suspended while the card is powered up. Add
the ability to stay runtime-resumed in that case and enable it with a new
quirk SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/mmc/host/atmel-mci.c:2509:12: warning: 'atmci_suspend' defined but not used [-Wunused-function]
drivers/mmc/host/atmel-mci.c:2539:12: warning: 'atmci_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add support for initialising DMA from the Device Tree.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This removes the deprecated use of the .private member of struct dma_chan
and switches the sdhi / tmio mmc driver to using the
dmaengine_slave_config() channel configuration method.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
So far only the SDHI implementation uses TMIO MMC with DMA. That way a DMA
channel filter function, defined in the TMIO driver wasn't a problem.
However, such a filter function is DMA controller specific. Since the SDHI
glue is only running on systems with the SHDMA DMA controller, the filter
function can safely be provided by it. Move it into SDHI.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
If pending interrupt for IDMAC exists when initialize IDMAC, it will
call interrupt handler unnecessarily.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Use the saved values in card->ext_csd when selecting power class.
By doing this the power class will be selected even if mmc_init_card
is called with oldcard != NULL, which is the case after a suspend/resume.
Today ext_csd is NULL if mmc_init_card is called with oldcard != NULL
and power class will not be selected.
According to the eMMC specification the POWER_CLASS value is reset after
power failure, H/W reset assertion and any CMD0 reset.
Signed-off-by: Fredrik Soderstedt <fredrik.soderstedt@stericsson.com>
Reviewed-by: Johan Rudholm <jrudholm@gmail.com>
Acked By: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The mmc_card_sleep|awake APIs are not being used since the support is
already properly encapsulated within the suspend sequence. Sleep|awake
command is also specific for eMMC.
We remove the sleep|awake bus_ops, the mmc_card_sleep|awake APIs and
move the code into the mmc specific core instead. This also includes
the mmc ops function, mmc_sleepawake. All releated functions have then
become static and we have got far less code to maintain.
Additionally this patch also simplifies the code from mmc_sleepawake,
since it is only used to put the card to sleep and not awake.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Aggressive power management is suitable when saving power is
essential. At request inactivity timeout, aka pm runtime
autosuspend timeout, the card will be suspended.
Once a new request arrives, the card will be re-initalized and
thus the first request will suffer from a latency. This latency
is card-specific, experiments has shown in general that SD-cards
has quite poor initialization time, around 300ms-1100ms. eMMC is
not surprisingly far better but still a couple of hundreds of ms
has been observed.
Except for the request latency, it is important to know that
suspending the card will also prevent the card from executing
internal house-keeping operations in idle mode. This could mean
degradation in performance.
To use this feature make sure the request inactivity timeout is
chosen carefully. This has not been done as a part of this patch.
Enable this feature by using host cap MMC_CAP_AGGRESSIVE_PM and
by setting CONFIG_MMC_UNSAFE_RESUME.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
