Age | Commit message (Collapse) | Author |
|
On s390 I have seen some random
"Warning: unable to open an initial console"
boot failure. Turns out that tty_open fails, because the
hvc_alloc was not yet done. In former times this could not happen,
since the probe function automatically called hvc_alloc. With newer
versions (multiport) some host<->guest interaction is required
before hvc_alloc is called. This might be too late, especially if
an initramfs is involved. Lets use a completion if we have
multiport and an early console.
[Amit:
* Use NULL instead of 0 for pointer comparison
* Rename 'port_added' to 'early_console_added'
* Re-format, re-word commit message
* Rebase patch on top of current queue]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Chrstian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
This commit adds port-specific stats for the number of bytes received,
sent and discarded. They're exposed via the debugfs interface. This
data can be used to check for data loss bugs (or disprove such claims).
It can also be used for accounting, if there's such a need.
The stats remain valid throughout the lifetime of the port. Unplugging
a port will reset the stats. The numbers are not reset across port
opens/closes.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
discard_port_data() used virtqueue_get_buf() directly instead of using
get_inbuf(). Fix this, so that we get accounting for all received
bytes. This also simplifies the code a lot.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
'ret' is a misnomer in discard_port_data() since we don't return the
value. Rename it to 'err'.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Instead of pulling in a buffer from the vq each time it's called,
get_inbuf() now checks if the current active buffer, in port->inbuf is
valid. If it is, just returns a pointer to it. This ends up
simplifying a lot of code calling get_inbuf() since the check for
port->inbuf being valid was done by all the callers.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
get_inbuf() returns void *. There's no reason to return void pointers
instead of the correct struct port_buffer *.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Get ready to support suspend/resume by using the freezable calls so that
blocking read/write syscalls are handled properly across suspend/resume.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
We don't allow port name changes dynamically for a port. So any
requests by the host to change the name are ignored.
Before this patch, if the hypervisor sent a port name while we had one
set already, we would leak memory equivalent to the size of the old
name.
This scenario wasn't expected so far, but with the suspend-resume
support, we'll send the VIRTIO_CONSOLE_PORT_READY message after restore,
which can get us into this situation.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Convert spaces to tabs and fix indentation for an if statement split
into multiple lines.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
This patch modifies virtio-net to use virtio_config_val() instead
of a 'if(virtio_has_feature()) vdev->config->get()' construct to retrieve
optional values from the config space.
Cc: Amit Shah <amit.shah@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
This patch modifies virtio-console to use virtio_config_val() instead
of a 'if(virtio_has_feature()) vdev->config->get()' construct to retrieve
optional values from the config space.
Cc: Amit Shah <amit.shah@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
* 'for-linus/i2c-3.2' of git://git.fluff.org/bjdooks/linux: (47 commits)
i2c-s3c2410: Add device tree support
i2c-s3c2410: Keep a copy of platform data and use it
i2c-nomadik: cosmetic coding style corrections
i2c-au1550: dev_pm_ops conversion
i2c-au1550: increase timeout waiting for master done
i2c-au1550: remove unused ack_timeout
i2c-au1550: remove usage of volatile keyword
i2c-tegra: __iomem annotation fix
i2c-eg20t: Add initialize processing in case i2c-error occurs
i2c-eg20t: Fix flag setting issue
i2c-eg20t: add stop sequence in case wait-event timeout occurs
i2c-eg20t: Separate error processing
i2c-eg20t: Fix 10bit access issue
i2c-eg20t: Modify returned value s32 to long
i2c-eg20t: Fix bus-idle waiting issue
i2c-designware: Fix PCI core warning on suspend/resume
i2c-designware: Add runtime power management support
i2c-designware: Add support for Designware core behind PCI devices.
i2c-designware: Push all register reads/writes into the core code.
i2c-designware: Support multiple cores using same ISR
...
|
|
* 'for-linus' of git://opensource.wolfsonmicro.com/regulator: (22 commits)
regulator: Constify constraints name
regulator: Fix possible nullpointer dereference in regulator_enable()
regulator: gpio-regulator add dependency on GENERIC_GPIO
regulator: Add module.h include to gpio-regulator
regulator: Add driver for gpio-controlled regulators
regulator: remove duplicate REG_CTRL2 defines in tps65023
regulator: Clarify documentation for regulator-regulator supplies
regulator: Fix some bitrot in the machine driver documentation
regulator: tps65023: Added support for the similiar TPS65020 chip
regulator: tps65023: Setting correct core regulator for tps65021
regulator: tps65023: Set missing bit for update core-voltage
regulator: tps65023: Fixes i2c configuration issues
regulator: Add debugfs file showing the supply map table
regulator: tps6586x: add SMx slew rate setting
regulator: tps65023: Fixes i2c configuration issues
regulator: tps6507x: Remove num_voltages array
regulator: max8952: removed unused mutex.
regulator: fix regulator/consumer.h kernel-doc warning
regulator: Ensure enough enable time for max8649
regulator: 88pm8607: Fix off-by-one value range checking in the case of no id is matched
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: fix isochronous DMA synchronization
firewire: ohci: work around selfID junk due to wrong gap count
firewire: net: Use posted writes
firewire: use clamp and min3 macros
firewire: ohci: optimize TSB41BA3D detection
firewire: ohci: TSB41BA3D support tweaks
firewire: ohci: Add support for TSB41BA3D phy
firewire: ohci: Move code from the bus reset tasklet into a workqueue
firewire: sbp2: fold two functions into one
firewire: sbp2: move some code to more sensible places
firewire: sbp2: remove obsolete reference counting
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
* 'pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
pstore: make pstore write function return normal success/fail value
pstore: change mutex locking to spin_locks
pstore: defer inserting OOPS entries into pstore
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (62 commits)
mlx4_core: Deprecate log_num_vlan module param
IB/mlx4: Don't set VLAN in IBoE WQEs' control segment
IB/mlx4: Enable 4K mtu for IBoE
RDMA/cxgb4: Mark QP in error before disabling the queue in firmware
RDMA/cxgb4: Serialize calls to CQ's comp_handler
RDMA/cxgb3: Serialize calls to CQ's comp_handler
IB/qib: Fix issue with link states and QSFP cables
IB/mlx4: Configure extended active speeds
mlx4_core: Add extended port capabilities support
IB/qib: Hold links until tuning data is available
IB/qib: Clean up checkpatch issue
IB/qib: Remove s_lock around header validation
IB/qib: Precompute timeout jiffies to optimize latency
IB/qib: Use RCU for qpn lookup
IB/qib: Eliminate divide/mod in converting idx to egr buf pointer
IB/qib: Decode path MTU optimization
IB/qib: Optimize RC/UC code by IB operation
IPoIB: Use the right function to do DMA unmap pages
RDMA/cxgb4: Use correct QID in insert_recv_cqe()
RDMA/cxgb4: Make sure flush CQ entries are collected on connection close
...
|
|
'misc', 'mlx4', 'misc', 'nes', 'qib' and 'xrc' into for-next
|
|
* git://github.com/herbertx/crypto: (48 commits)
crypto: user - Depend on NET instead of selecting it
crypto: user - Add dependency on NET
crypto: talitos - handle descriptor not found in error path
crypto: user - Initialise match in crypto_alg_match
crypto: testmgr - add twofish tests
crypto: testmgr - add blowfish test-vectors
crypto: Make hifn_795x build depend on !ARCH_DMA_ADDR_T_64BIT
crypto: twofish-x86_64-3way - fix ctr blocksize to 1
crypto: blowfish-x86_64 - fix ctr blocksize to 1
crypto: whirlpool - count rounds from 0
crypto: Add userspace report for compress type algorithms
crypto: Add userspace report for cipher type algorithms
crypto: Add userspace report for rng type algorithms
crypto: Add userspace report for pcompress type algorithms
crypto: Add userspace report for nivaead type algorithms
crypto: Add userspace report for aead type algorithms
crypto: Add userspace report for givcipher type algorithms
crypto: Add userspace report for ablkcipher type algorithms
crypto: Add userspace report for blkcipher type algorithms
crypto: Add userspace report for ahash type algorithms
...
|
|
'for-32/i2c/tegra-iomem' into for-linus/i2c-3.2
|
|
Conflicts:
drivers/i2c/busses/i2c-designware-core.c
Fixed up merge conflic
|
|
'for-32/i2c/eg20t-v4', 'for-32/i2c/designware-v5' and 'for-32/i2c/au1550' into for-linus/i2c-3.2
|
|
Quoth Andrew:
- Most of MM. Still waiting for the poweroc guys to get off their
butts and review some threaded hugepages patches.
- alpha
- vfs bits
- drivers/misc
- a few core kerenl tweaks
- printk() features
- MAINTAINERS updates
- backlight merge
- leds merge
- various lib/ updates
- checkpatch updates
* akpm: (127 commits)
epoll: fix spurious lockdep warnings
checkpatch: add a --strict check for utf-8 in commit logs
kernel.h/checkpatch: mark strict_strto<foo> and simple_strto<foo> as obsolete
llist-return-whether-list-is-empty-before-adding-in-llist_add-fix
wireless: at76c50x: follow rename pack_hex_byte to hex_byte_pack
fat: follow rename pack_hex_byte() to hex_byte_pack()
security: follow rename pack_hex_byte() to hex_byte_pack()
kgdb: follow rename pack_hex_byte() to hex_byte_pack()
lib: rename pack_hex_byte() to hex_byte_pack()
lib/string.c: fix strim() semantics for strings that have only blanks
lib/idr.c: fix comment for ida_get_new_above()
lib/percpu_counter.c: enclose hotplug only variables in hotplug ifdef
lib/bitmap.c: quiet sparse noise about address space
lib/spinlock_debug.c: print owner on spinlock lockup
lib/kstrtox: common code between kstrto*() and simple_strto*() functions
drivers/leds/leds-lp5521.c: check if reset is successful
leds: turn the blink_timer off before starting to blink
leds: save the delay values after a successful call to blink_set()
drivers/leds/leds-gpio.c: use gpio_get_value_cansleep() when initializing
drivers/leds/leds-lm3530.c: add __devexit_p where needed
...
|
|
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make sure that the reset is successful by issuing a dummy read to R
channel current register and check its default value. On some platforms,
without this dummy read, any further access to {R/G/B}_EXEC will not have
any impact.
[akpm@linux-foundation.org: fix up code comment]
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Tested-by: Naga Radhesh <naga.radheshy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Depending on the implementation of the hardware blinking function in
blink_set(), the led can support hardware blinking for some values of
delay_on and delay_off and fall-back to software blinking for some other
values.
Turning off the blink_timer unconditionally before starting to blink
make sure that a sequence like:
OFF
hardware blinking
software blinking
hardware blinking
does not leave the software blinking timer active.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: <stable@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When calling the hardware blinking function implemented by blink_set(),
the delay_on and delay_off values are not preserved across calls.
Fix that and make the "timer" trigger work as expected when hardware
blinking is available.
BEFORE the fix:
$ cd /sys/class/leds/someled
$ echo timer > trigger
$ cat delay_on delay_off
0
0
$ echo 100 > delay_on
$ cat delay_on delay_off
0
0
$ echo 100 > delay_off
$ cat delay_on delay_off
0
0
AFTER the fix:
$ cd /sys/class/leds/someled
$ echo timer > trigger
$ cat delay_on delay_off
0
0
$ echo 100 > delay_on
$ cat delay_on delay_off
100
0
$ echo 100 > delay_off
$ cat delay_on delay_off
100
100
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: <stable@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I get the following warning:
------------[ cut here ]------------
WARNING: at drivers/gpio/gpiolib.c:1559 __gpio_get_value+0x90/0x98()
Modules linked in:
Call Trace:
[<ffffffff81440950>] dump_stack+0x8/0x34
[<ffffffff81141478>] warn_slowpath_common+0x78/0xa0
[<ffffffff812f0958>] __gpio_get_value+0x90/0x98
[<ffffffff81434f04>] create_gpio_led+0xdc/0x194
[<ffffffff8143524c>] gpio_led_probe+0x290/0x36c
[<ffffffff8130e8b0>] driver_probe_device+0x78/0x1b0
[<ffffffff8130eaa8>] __driver_attach+0xc0/0xc8
[<ffffffff8130d7ac>] bus_for_each_dev+0x64/0xb0
[<ffffffff8130e130>] bus_add_driver+0x1c8/0x2a8
[<ffffffff8130f100>] driver_register+0x90/0x180
[<ffffffff81100438>] do_one_initcall+0x38/0x160
---[ end trace ee38723fbefcd65c ]---
My GPIOs are on an I2C port expander, so we must use the *_cansleep()
variant of the GPIO functions. This is was not being done in
create_gpio_led().
We can change gpio_get_value() to gpio_get_value_cansleep() because it is
only called from the platform_driver probe function, which is a context
where we can sleep.
Only tested on my gpio_cansleep() system, but it seems safe for all
systems.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Trent Piepho <tpiepho@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
According to the comments in include/linux/init.h:
"Pointers to __devexit functions must use __devexit_p(function_name), the
wrapper will insert either the function_name or NULL, depending on the config
options."
We have __devexit annotation for lm3530_remove(), so add __devexit_p to
the `struct i2c_driver'.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
LP5521_REG_OP_MODE register
If lp5521_read fails, engine_state variable is not initialized.
If lp5521_read fails, we should return error.
This patch fixes below warning.
CC drivers/leds/leds-lp5521.o
drivers/leds/leds-lp5521.c: In function 'lp5521_set_engine_mode':
drivers/leds/leds-lp5521.c:168: warning: 'engine_state' may be used uninitialized in this function
[akpm@linux-foundation.org: remove unneeded "ret |="]
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use the platform_data include directory for the TPU LED driver, as
suggested by Paul Mundt.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use a workqueue in the Renesas TPU LED driver to allow the Runtime PM code
to sleep.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A few new i2c-drivers came into the kernel which clear the
clientdata-pointer on exit or error. This is obsolete meanwhile, the core
will do it.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The memory for struct led_trigger should be kfreed in the
led_trigger_register() error path. Also this function should return NULL
on error.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add V2 of the LED driver for a single timer channel for the TPU hardware
block commonly found in Renesas SoCs.
The driver has been written with optimal Power Management in mind, so to
save power the LED is driven as a regular GPIO pin in case of maximum
brightness and power off which allows the TPU hardware to be idle and
which in turn allows the clocks to be stopped and the power domain to be
turned off transparently.
Any other brightness level requires use of the TPU hardware in PWM mode.
TPU hardware device clocks and power are managed through Runtime PM.
System suspend and resume is known to be working - during suspend the LED
is set to off by the generic LED code.
The TPU hardware timer is equipeed with a 16-bit counter together with an
up-to-divide-by-64 prescaler which makes the hardware suitable for
brightness control. Hardware blink is unsupported.
The LED PWM waveform has been verified with a Fluke 123 Scope meter on a
sh7372 Mackerel board. Tested with experimental sh7372 A3SP power domain
patches. Platform device bind/unbind tested ok.
V2 has been tested on the DS2 LED of the sh73a0-based AG5EVM.
[axel.lin@gmail.com: include linux/module.h]
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The rename of corgibl_limit_intensity is missed in commit d00ba726
("backlight: Rename the corgi backlight driver to generic"). Let's fix it
now.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
error handling
Using gpio_request_one can make the error handling simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The regulator support in the l4f00242t03 is very non-idiomatic. Rather
than requesting the regulators based on the device name and the supply
names used by the device the driver requires boards to pass system
specific supply names around through platform data. The driver also
conditionally requests the regulators based on this platform data, adding
unneeded conditional code to the driver.
Fix this by removing the platform data and converting to the standard
idiom, also updating all in tree users of the driver. As no datasheet
appears to be available for the LCD I'm guessing the names for the
supplies based on the existing users and I've no ability to do anything
more than compile test.
The use of regulator_set_voltage() in the driver is also problematic,
since fixed voltages are required the expectation would be that the
voltages would be fixed in the constraints set by the machines rather than
manually configured by the driver, but is less problematic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A few new i2c-drivers came into the kernel which clear the
clientdata-pointer on exit or error. This is obsolete meanwhile, the core
will do it.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Standardize the style for compiler based printf format verification.
Standardized the location of __printf too.
Done via script and a little typing.
$ grep -rPl --include=*.[ch] -w "__attribute__" * | \
grep -vP "^(tools|scripts|include/linux/compiler-gcc.h)" | \
xargs perl -n -i -e 'local $/; while (<>) { s/\b__attribute__\s*\(\s*\(\s*format\s*\(\s*printf\s*,\s*(.+)\s*,\s*(.+)\s*\)\s*\)\s*\)/__printf($1, $2)/g ; print; }'
[akpm@linux-foundation.org: revert arch bits]
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 6c536e4ce8e ("ad525x_dpot: add support for SPI parts") added
support for the AD5161 through SPI, but the device supports both I2C and
SPI (depending on the DIS pin), so add it to -i2c as well.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Cc: Donggeun Kim <dg77.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The regulator API contains a range of features for stubbing itself out
when not in use and for transparently restricting the actual effect of
regulator API calls where they can't be supported on a particular system
so that drivers don't need to individually implement this. Simplify the
driver slightly by making use of this idiom.
The only in tree user is ecovec24 which does not use the regulator API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
[ilkka.koskinen@nokia.com: fix arg to lis3->read()]
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Subject: lis3-remove-the-references-to-the-global-variable-in-core-driver-fix
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change exported functions to use the device given as parameter
instead of the global one.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add axis correction for HP ProBook 6555b.
Signed-off-by: Malte Starostik <m-starostik@versanet.de>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add axis correction for HP EliteBook 8540w.
Reported-by: Lyall Pearce <lyall.pearce@hp.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add axis correction for HP EliteBook 2730p.
Tested-by: Witold Pilat <witold.pilat@gmail.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
After an "unexpected" reboot, I found this Oops in my logs:
divide error: 0000 [#1] PREEMPT SMP=20
CPU 0=20
Modules linked in: lis3lv02d hp_wmi input_polldev [...]
Pid: 390, comm: modprobe Tainted: G C 2.6.39-rc7-wl+=20
RIP: 0010:[<ffffffffa014b427>] [<ffffffffa014b427>]
lis3lv02d_poweron+0x4e/0x94 [lis3lv02d]
RSP: 0018:ffff8801d6407cf8 EFLAGS: 00010246
RAX: 0000000000000bb8 RBX: ffffffffa014e000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffea00066e4708 RDI: ffff8801df002700
RBP: ffff8801d6407d18 R08: ffffea00066c5a30 R09: ffffffff812498c9
R10: ffff8801d7bfcea0 R11: ffff8801d7bfce10 R12: 0000000000000bb8
R13: 00000000ffffffda R14: ffffffffa0154120 R15: ffffffffa0154030
=46S: 00007fc0705db700(0000) GS:ffff8801dfa00000(0000) knlGS:0
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007f33549174f0 CR3: 00000001d65c9000 CR4: 00000000000406f0
Process modprobe (pid: 390, threadinfo ffff8801d6406000, task ffff8801d6b40=
000)
Stack:
ffffffffa0154120 62ffffffa0154030 ffffffffa014e000 00000000ffffffea
ffff8801d6407d58 ffffffffa014bcc1 0000000000000000 0000000000000048
ffff8801d8bae800 00000000ffffffea 00000000ffffffda ffffffffa0154120
Call Trace:
[<ffffffffa014bcc1>] lis3lv02d_init_device+0x1ce/0x496 [lis3lv02d]
[<ffffffffa01522ff>] lis3lv02d_add+0x10f/0x17c [hp_accel]
[<ffffffff81233e11>] acpi_device_probe+0x49/0x117
[...]
Code: 3a 75 06 80 4d ef 50 eb 04 80 4d ef 40 0f b6 55 ef be 21
00 00 00 48 89 df ff 53 18 44 8b 63 6c e8 3e fc ff ff 89 c1 44
89 e0 99 <f7> f9 89 c7 e8 93 82 ef e0 48 83 7b 30 00 74 2d 45
31 e4 80 7b=20
RIP [<ffffffffa014b427>] lis3lv02d_poweron+0x4e/0x94 [lis3lv02d]
RSP <ffff8801d6407cf8>
>From my POV, it looks like the hardware is not working as expected
and returns a bogus data rate. The driver doesn't check the result
and directly uses it as some sort of divisor in some places:
msleep(lis3->pwron_delay / lis3lv02d_get_odr());
Under this circumstances, this could very well cause the
"divide by zero" exception from above.
For now, I fixed it the easiest and most obvious way:
Check if the result is sane and if it isn't use a sane default
instead. I went for "100" in the latter case, simply because
/sys/devices/platform/lis3lv02d/rate returns it on a successful
boot.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|