| Age | Commit message (Collapse) | Author |
|---|
|
This fixes pxa2xx_udc.c to include asm/arch/udc.h again to fix current
build breakage.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
[ forwarded by David Brownell <david-b@pacbell.net> ]
[ fixed to apply properly by Linus ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/devfs-2.6: (22 commits)
[PATCH] devfs: Remove it from the feature_removal.txt file
[PATCH] devfs: Last little devfs cleanups throughout the kernel tree.
[PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
[PATCH] devfs: Remove the tty_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the line_driver devfs_name field as it's no longer needed
[PATCH] devfs: Remove the videodevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the gendisk devfs_name field as it's no longer needed
[PATCH] devfs: Remove the miscdevice devfs_name field as it's no longer needed
[PATCH] devfs: Remove the devfs_fs_kernel.h file from the tree
[PATCH] devfs: Remove devfs_remove() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_cdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_bdev() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_symlink() function from the kernel tree
[PATCH] devfs: Remove devfs_mk_dir() function from the kernel tree
[PATCH] devfs: Remove devfs_*_tape() functions from the kernel tree
[PATCH] devfs: Remove devfs support from the sound subsystem
[PATCH] devfs: Remove devfs support from the ide subsystem.
[PATCH] devfs: Remove devfs support from the serial subsystem
[PATCH] devfs: Remove devfs from the init code
[PATCH] devfs: Remove devfs from the partition code
...
|
|
Conflicts:
drivers/char/agp/Kconfig
|
|
If all drivers go away before all ISDN network interfaces are closed we got
a OOps on removing interfaces, this patch avoid it.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
most current laptops do not work without allowing shared cardbus IRQs.
This patch enables IRQ sharing, so these cards work again.
This was tested with shared and none shared cardbus IRQs on different laptops
without problems.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (43 commits)
[POWERPC] Use little-endian bit from firmware ibm,pa-features property
[POWERPC] Make sure smp_processor_id works very early in boot
[POWERPC] U4 DART improvements
[POWERPC] todc: add support for Time-Of-Day-Clock
[POWERPC] Make lparcfg.c work when both iseries and pseries are selected
[POWERPC] Fix idr locking in init_new_context
[POWERPC] mpc7448hpc2 (taiga) board config file
[POWERPC] Add tsi108 pci and platform device data register function
[POWERPC] Add general support for mpc7448hpc2 (Taiga) platform
[POWERPC] Correct the MAX_CONTEXT definition
powerpc: minor cleanups for mpc86xx
[POWERPC] Make sure we select CONFIG_NEW_LEDS if ADB_PMU_LED is set
[POWERPC] Simplify the code defining the 64-bit CPU features
[POWERPC] powerpc: kconfig warning fix
[POWERPC] Consolidate some of kernel/misc*.S
[POWERPC] Remove unused function call_with_mmu_off
[POWERPC] update asm-powerpc/time.h
[POWERPC] Clean up it_lp_queue.h
[POWERPC] Skip the "copy down" of the kernel if it is already at zero.
[POWERPC] Add the use of the firmware soft-reset-nmi to kdump.
...
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (23 commits)
[PARISC] Move os_id_to_string() inside #ifndef __ASSEMBLY__
[PARISC] Fix do_gettimeofday() hang
[PARISC] Fix PCREL22F relocation problem for most modules
[PARISC] Refactor show_regs in traps.c
[PARISC] Add os_id_to_string helper
[PARISC] OS_ID_LINUX == 0x0006
[PARISC] Ensure Space ID hashing is turned off
[PARISC] Match show_cache_info with reality
[PARISC] Remove unused macro fixup_branch in syscall.S
[PARISC] Add is_compat_task() helper
[PARISC] Update Thibaut Varene's CREDITS entry
[PARISC] Reduce data footprint in pdc_stable.c
[PARISC] pdc_stable version 0.30
[PARISC] Work around machines which do not support chassis warnings
[PARISC] PDC_CHASSIS is implemented on all machines
[PARISC] Remove unconditional #define PIC in syscall macros
[PARISC] Use MFIA in current_text_addr on pa2.0 processors
[PARISC] Remove dead function pc_in_user_space
[PARISC] Test ioc_needs_fdc variable instead of open coding
[PARISC] Fix gcc 4.1 warnings in sba_iommu.c
...
|
|
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (28 commits)
[S390] rework of channel measurement facility.
[S390] appldata enhancements.
[S390] Add vmpanic parameter.
[S390] add PAV support to the dasd driver.
[S390] remove export of sys_call_table
[S390] remove unused macros from binfmt_elf32.c
[S390] fix duplicate export of overflow{ug}id
[S390] cio chpid offline.
[S390] avenrun export in appdata_base.c
Convert s390_collect_crw_info() in s390mach.c from being started
[S390] dasd eer data format.
[S390] preempt_count initialization.
[S390] head.S code moving.
[S390] dasd whitespace and other cosmetics.
[S390] virtual cpu accounting vs. machine checks.
[S390] add __cpuinit to appldata cpu hotplug notifier.
[S390] dasd_eckd_dump_sense bug.
[S390] missing check in dasd_eer_open.
[S390] modular 3270 driver.
[S390] console_unblank woes.
...
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
|
|
This patch-queue improves the generic IRQ layer to be truly generic, by adding
various abstractions and features to it, without impacting existing
functionality.
While the queue can be best described as "fix and improve everything in the
generic IRQ layer that we could think of", and thus it consists of many
smaller features and lots of cleanups, the one feature that stands out most is
the new 'irq chip' abstraction.
The irq-chip abstraction is about describing and coding and IRQ controller
driver by mapping its raw hardware capabilities [and quirks, if needed] in a
straightforward way, without having to think about "IRQ flow"
(level/edge/etc.) type of details.
This stands in contrast with the current 'irq-type' model of genirq
architectures, which 'mixes' raw hardware capabilities with 'flow' details.
The patchset supports both types of irq controller designs at once, and
converts i386 and x86_64 to the new irq-chip design.
As a bonus side-effect of the irq-chip approach, chained interrupt controllers
(master/slave PIC constructs, etc.) are now supported by design as well.
The end result of this patchset intends to be simpler architecture-level code
and more consolidation between architectures.
We reused many bits of code and many concepts from Russell King's ARM IRQ
layer, the merging of which was one of the motivations for this patchset.
This patch:
rename desc->handler to desc->chip.
Originally i did not want to do this, because it's a big patch. But having
both "desc->handler", "desc->handle_irq" and "action->handler" caused a
large degree of confusion and made the code appear alot less clean than it
truly is.
I have also attempted a dual approach as well by introducing a
desc->chip alias - but that just wasnt robust enough and broke
frequently.
So lets get over with this quickly. The conversion was done automatically
via scripts and converts all the code in the kernel.
This renaming patch is the first one amongst the patches, so that the
remaining patches can stay flexible and can be merged and split up
without having some big monolithic patch act as a merge barrier.
[akpm@osdl.org: build fix]
[akpm@osdl.org: another build fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Coverity spotted this leak (id #613), when we are not configured, we return
without freeing the allocated skb.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
AFAICT, this is x86 only, so the patch below is needed to stop this new
option showing up on PPC, IA64, etc..
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Another possible dereference detected by coverity (id #759). pf_probe()
might call pf_identify() which might call get_capacity() which dereferences
pf->disk
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Documention/pci.txt states..
"The struct pci_driver shouldn't be marked with any of these tags."
(Referring to __devinit and friends).
(akpm: good documentation, that. Link this driver into vmlinux with hotplug
CPU disabled and it'll crash).
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Brent Casavant <bcasavan@sgi.com>
Cc: Pat Gefre <pfg@sgi.com>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
drivers/built-in.o: In function `sgivwfb_set_par':
sgivwfb.c:(.text+0x88583): undefined reference to `sgivwfb_mem_phys'
sgivwfb.c:(.text+0x88596): undefined reference to `sgivwfb_mem_phys'
sgivwfb.c:(.text+0x885a8): undefined reference to `sgivwfb_mem_phys'
drivers/built-in.o: In function `sgivwfb_check_var':
sgivwfb.c:(.text+0x88ad0): undefined reference to `sgivwfb_mem_size'
drivers/built-in.o: In function `sgivwfb_mmap':
sgivwfb.c:(.text+0x88c75): undefined reference to `sgivwfb_mem_size'
sgivwfb.c:(.text+0x88c7f): undefined reference to `sgivwfb_mem_phys'
drivers/built-in.o: In function `sgivwfb_probe':
sgivwfb.c:(.init.text+0x4060): undefined reference to `sgivwfb_mem_size'
sgivwfb.c:(.init.text+0x4065): undefined reference to `sgivwfb_mem_phys'
sgivwfb.c:(.init.text+0x4076): undefined reference to `sgivwfb_mem_phys'
sgivwfb.c:(.init.text+0x409c): undefined reference to `sgivwfb_mem_size'
sgivwfb.c:(.init.text+0x410e): undefined reference to `sgivwfb_mem_size'
sgivwfb.c:(.init.text+0x4113): undefined reference to `sgivwfb_mem_phys'
sgivwfb.c:(.init.text+0x4162): undefined reference to `sgivwfb_mem_size'
sgivwfb.c:(.init.text+0x4168): undefined reference to `sgivwfb_mem_phys'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fixes for several channel measurement facility bugs:
* Blocks copied from the hardware might not be consistent. Solve this
by moving the copying into idle state and repeating the copying.
* avg_sample_interval changed with every read, even though no new block
was available. Solve this by storing a timestamp when the last new
block was received.
* Several locking issues.
* Measurements were not reenabled after a disconnected device became
available again.
* Remove #defines for ioctls that were never implemented.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Add support for parallel-access-volumes to the dasd driver. This
allows concurrent access to dasd devices with multiple channel
programs.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
After setting a path to a dasd offline at the SE, I/O hangs on that
dasd for 5 minutes, then continues.
I/O for which an interrupt will not be reported after the channel
path has been disabled was not terminated by the common I/O layer,
causing the dasd MIH to hit after 5 minutes.
Be more aggressive in terminating I/O after setting a channel path
offline. Also make sure to generate a fake irb if the device
driver issues an I/O request after being notified of the killed
I/O and clear residual information from the irb before trying to
start the delayed verification.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
as a deprecated kernel_thread to a kthread.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The struct dasd_eer_header needs the packed attribute, or there will
be 6 additional bytes of random data between the fixed header and
the variable length part of the eer data.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Dasd code cleanup: 1) remove white space, 2) remove the emacs override
sections, and 3) use kzalloc instead of kmalloc.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The ccw dump function dasd_eckd_dump_ccw_range can crash because
it does not take care about the IDAL flag in the ccw.
Check for IDALs flag set in CCW and follow the indirect list to
print the data that is refered by the ccw.
Signed-off-by: Horst Hummel <horst.hummel@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Check the return value of kzalloc in dasd_eer_open.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The initial i/o to a 3270 device is done using the static module variables
raw3270_init_data and raw3270_init_request. If the 3270 device driver is
built as a module and gets loaded above 2GB, the initial i/o will fail
because these variables will get addresses > 2GB. To make it work the
two variables are moved to struct raw3270 and the data structure is
allocated with GFP_DMA.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Changes in the DASD driver require an asynchronous implementation of the
subchannel reprobe loop. This loop was so far only used by the blacklisting
mechanism but is now available to all CCW device drivers.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Work around the problem that a device cannot be unregistered from
driver_for_each_device() because of klist node refcounting: Get device
after device owned by the driver to be unregistered with driver_find_device()
and then unregister it. This works because driver_get_device() gets us out of
the region of the elevated klist node refcount. driver_find_device() will
always get the next device in the list after the found one has been
unregistered.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Specify correct sizeof() in chp_measurement_read() and return
correct amount of read data.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Trying to set a DASD root device online can fail under some circumstances
with the message "Read configuration data returned error -5". The cause
is that read configuration data incorrectly aborts with -EIO when it
encounters a temporary busy condition at a storage server.
Perform retry when encountering temporary busy conditions.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] Documentation/watchdog update
[WATCHDOG] convert AT91RM9200 watchdog to platform driver
[WATCHDOG] add WDIOC_GETTIMELEFT ioctl
[WATCHDOG] Pre-Timeout flags
|
|
This patch adds earlier initialization of spi_device.mode, as needed
on boards using nondefault chipselect polarity. An example would be
ones using the RS5C348 RTC without an external signal inverter between
the RTC chipselect and the SPI controller.
Without this mechanism, the first setup() call for that chip would
wrongly enable chips, corrupting transfers to/from other chips sharing
that SPI bus.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/dtor/input:
Input: db9 - fix potential buffer overrun
Input: atkbd - fix hardware autorepeat
Input: wistron - add mapping for Wistron MS 2111
|
|
Clean out the 68328serial driver:
. remove use of cli/sti
. fix usage of tty_* calls
. remove unused variables
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
work on libata ports)
Also sets the new fifo flag so that we don't hang on some errors with this
chipset.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Move auto arrays to static (const). Clean up using PCI_DEVICE in places,
remove unreachable junk and dead code.
Fix the serverworks cable detect logic (if ordering is wrong). Backport
from libata. Plenty of scope for more cleanup left.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
If the controller FIFO cleared automatically on error we must not try
and drain it as this will hang some chips.
Based in concept on a broken patch from -mm some while back
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Kill a pair of long escaped debug printk calls
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove all the ifdef preparation for enhanced features that never occcurred
and is only in libata. For the SATA chips (but not yet PATA ones) politely
suggest to the user that libata may offer more features.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Sergei Shtylylov <sshtylyov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This is based on the proposed patches flying around but also checks that
the device in question is new enough to have word 93 rather thanb blindly
assuming word 93 == 0 means SATA (see ATA-5, ATA-7)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix a erroneous calculation of the legacy brightness values as reported by
Paul Collins. Additionally, it moves the calculation of the negative value
in the radeonfb driver after the value check.
Signed-off-by: Michael Hanselmann <linux-kernel@hansmi.ch>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Collins <paul@briny.ondioline.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Modify the watchdog timeout in IPMI to only do things at panic/reboot time if
the watchdog timer was already running. Some BIOSes do not disable the
watchdog timer at startup, and this led to a reboot a while later if the new
OS running didn't start monitoring the watchdog, even if the watchdog was not
running before.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
There was some old high-res-timer code in the IPMI driver that is dead.
Remove it.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Tidy up the timer usage in the IPMI driver.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Turned out to be rather a monster
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Works better on SMP if...
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove 'active' field from tty buffer structure. This was added in 2.6.16
as part of a patch to make the new tty buffering SMP safe. This field is
unnecessary with the more intelligently written flush_to_ldisc that adds
receive_room handling.
Removing this field reverts to simpler logic where the tail buffer is
always the 'active' buffer, which should not be freed by flush_to_ldisc.
(active == buffer being filled with new data)
The result is simpler, smaller, and faster tty buffer code.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Flush data serially to line discipline in blocks no larger than
tty->receive_room to avoid losing data if line discipline is busy (such as
N_TTY operating at high speed on heavily loaded system) or does not accept
data in large blocks (such as N_MOUSE).
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Remove TTY_DONT_FLIP tty flag. This flag was introduced in 2.1.X kernels
to prevent the N_TTY line discipline functions read_chan() and
n_tty_receive_buf() from running at the same time. 2.2.15 introduced
tty->read_lock to protect access to the N_TTY read buffer, which is the
only state requiring protection between these two functions.
The current TTY_DONT_FLIP implementation is broken for SMP, and is not
universally honored by drivers that send data directly to the line
discipline receive_buf function.
Because TTY_DONT_FLIP is not necessary, is broken in implementation, and is
not universally honored, it is removed.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add an SPI driver for the Ricoh RS5C348 RTC chip.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
