summaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)Author
2008-06-17atl1: relax eeprom mac address error checkRadu Cristescu
The atl1 driver tries to determine the MAC address thusly: - If an EEPROM exists, read the MAC address from EEPROM and validate it. - If an EEPROM doesn't exist, try to read a MAC address from SPI flash. - If that fails, try to read a MAC address directly from the MAC Station Address register. - If that fails, assign a random MAC address provided by the kernel. We now have a report of a system fitted with an EEPROM containing all zeros where we expect the MAC address to be, and we currently handle this as an error condition. Turns out, on this system the BIOS writes a valid MAC address to the NIC's MAC Station Address register, but we never try to read it because we return an error when we find the all- zeros address in EEPROM. This patch relaxes the error check and continues looking for a MAC address even if it finds an illegal one in EEPROM. Signed-off-by: Radu Cristescu <advantis@gmx.net> Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-17net/enc28j60: low power modeDavid Brownell
Keep enc28j60 chips in low-power mode when they're not in use. At typically 120 mA, these chips run hot even when idle; this low power mode cuts that power usage by a factor of around 100. This version provides a generic routine to poll a register until its masked value equals some value ... e.g. bit set or cleared. It's basically what the previous wait_phy_ready() did, but this version is generalized to support the handshaking needed to enter and exit low power mode. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Claudio Lanconelli <lanconelli.claudio@eptar.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-17net/enc28j60: section fixDavid Brownell
Minor bugfixes to the enc28j60 driver ... wrong section marking, indentation, and bogus use of spi_bus_type. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Claudio Lanconelli <lanconelli.claudio@eptar.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-17sky2: 88E8040T pci device idStephen Hemminger
Missed one pci id for 88E8040T. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-17netxen: download firmware in pci probeDhananjay Phadke
Downloading firmware in pci probe allows recovery in case of firmware failure by reloading the driver. Also reduced delays in firmware load. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-17netxen: cleanup debug messagesDhananjay Phadke
o Remove unnecessary debug prints and functions. o Explicitly specify pci class (0x020000) to avoid enabling management function. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-17netxen: remove global physical_port arrayDhananjay Phadke
Store physical port number in netxen_adapter structure. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-17netxen: fix portnum for hp mezz cardsDhananjay Phadke
This fixes a the issue where logical port number is set incorrectly for HP blade mezz cards. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-17ibm_newemac: select CRC32 in KconfigJosh Boyer
The ibm_newemac driver requires ether_crc to be defined. Apparently it is possible to generate a .config without CONFIG_CRC32 set which causes the following link errors if IBM_NEW_EMAC is selected: LD .tmp_vmlinux1 drivers/built-in.o: In function `emac_hash_mc': core.c:(.text+0x2f524): undefined reference to `crc32_le' core.c:(.text+0x2f528): undefined reference to `bitrev32' make: *** [.tmp_vmlinux1] Error 1 This patch has IBM_NEW_EMAC select CRC32 so we don't hit this error. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-16atm: [he] send idle cells instead of unassigned when in SDH modeChas Williams
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-16atm: [he] limit queries to the device's register spaceRobert T. Johnson
From: "Robert T. Johnson" <rtjohnso@eecs.berkeley.edu> Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
2008-06-16atm: [he] only support suni driver on multimode interfacesChas Williams
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-16atm: [iphase] doesn't call phy->start due to a bogus #ifndefJorge Boncompte [DTI2]
This causes the suni driver to oops if you try to use sonetdiag to get the statistics. Also add the corresponding phy->stop call to fix another oops if you try to remove the module. Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net> Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-16atm: [iphase] set drvdata before enabling interruptsJorge Boncompte [DTI2]
Signed-off-by: Jorge Boncompte [DTI2] <jorge@dti2.net> Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-14Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/linville/wireless-2.6
2008-06-13rt2x00: Add D-link DWA111 supportIvo van Doorn
Add new rt73usb USB ID for D-Link DWA111 Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-06-13ssb: Fix coherent DMA mask for PCI devicesMichael Buesch
This fixes setting the coherent DMA mask for PCI devices. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-06-13rt2x00: LEDS build failureRandy Dunlap
Config symbols that select LEDS_CLASS need to depend on NEW_LEDS so that undefined symbols are not used in the build. The alternative is to select NEW_LEDS, which some drivers do. This patch fixes the led_* symbols build errors. (.text+0x174cdc): undefined reference to `input_unregister_device' (.text+0x174d9f): undefined reference to `input_allocate_device' (.text+0x174e2d): undefined reference to `input_register_device' (.text+0x174e53): undefined reference to `input_free_device' rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device' rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event' rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event' (.text+0x176eca): undefined reference to `input_unregister_polled_device' (.text+0x176efc): undefined reference to `input_free_polled_device' (.text+0x176f37): undefined reference to `input_free_polled_device' (.text+0x176fd8): undefined reference to `input_register_polled_device' (.text+0x1772c0): undefined reference to `led_classdev_resume' (.text+0x1772d4): undefined reference to `led_classdev_resume' (.text+0x1772e8): undefined reference to `led_classdev_resume' (.text+0x17730a): undefined reference to `led_classdev_suspend' (.text+0x17731e): undefined reference to `led_classdev_suspend' (.text+0x17732f): undefined reference to `led_classdev_suspend' rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister' rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register' rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device' rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle' rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle' rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device' rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle' rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler' rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler' make[1]: *** [vmlinux] Error 1 Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-06-13rt2x00: INPUT build failureRandy Dunlap
Config symbols that select RFKILL need to depend on INPUT so that undefined symbols are not used in the build. This patch fixes the input_* symbols build errors. (.text+0x174cdc): undefined reference to `input_unregister_device' (.text+0x174d9f): undefined reference to `input_allocate_device' (.text+0x174e2d): undefined reference to `input_register_device' (.text+0x174e53): undefined reference to `input_free_device' rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device' rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event' rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event' (.text+0x176eca): undefined reference to `input_unregister_polled_device' (.text+0x176efc): undefined reference to `input_free_polled_device' (.text+0x176f37): undefined reference to `input_free_polled_device' (.text+0x176fd8): undefined reference to `input_register_polled_device' (.text+0x1772c0): undefined reference to `led_classdev_resume' (.text+0x1772d4): undefined reference to `led_classdev_resume' (.text+0x1772e8): undefined reference to `led_classdev_resume' (.text+0x17730a): undefined reference to `led_classdev_suspend' (.text+0x17731e): undefined reference to `led_classdev_suspend' (.text+0x17732f): undefined reference to `led_classdev_suspend' rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister' rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register' rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device' rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle' rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle' rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device' rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle' rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler' rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler' make[1]: *** [vmlinux] Error 1 Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-06-13b43: Fix noise calculation WARN_ONMichael Buesch
This removes a WARN_ON that is responsible for the following koops: http://www.kerneloops.org/searchweek.php?search=b43_generate_noise_sample The comment in the patch describes why it's safe to simply remove the check. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-06-13b43: Fix possible NULL pointer dereference in DMA codeMichael Buesch
This fixes a possible NULL pointer dereference in an error path of the DMA allocation error checking code. This is also necessary for a future DMA API change that is on its way into the mainline kernel that adds an additional dev parameter to dma_mapping_error(). This patch moves the whole struct b43_dmaring struct initialization right before any DMA allocation operation. Reported-by: Miles Lane <miles.lane@gmail.com> Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-06-13rt2x00: Restrict DMA to 32-bit addresses.Gertjan van Wingerde
None of the rt2x00 PCI devices support 64-bit DMA addresses (they all only accept 32-bit buffer addresses). Hence it makes no sense to try to enable 64-bit DMA addresses. Only try to enable 32-bit DMA addresses. Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-06-13rt2x00: Don't kill guardian_urb when it wasn't createdIvo van Doorn
This fixes a "BUG: unable to handle kernel paging request" bug in rt73usb which was caused by killing the guardian_urb while it had never been allocated for rt73usb. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-06-13Merge branch 'upstream-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev * 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: ahci: Workaround HW bug for SB600/700 SATA controller PMP support ahci: workarounds for mcp65
2008-06-13Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: tcp: Revert 'process defer accept as established' changes. ipv6: Fix duplicate initialization of rawv6_prot.destroy bnx2x: Updating the Maintainer net: Eliminate flush_scheduled_work() calls while RTNL is held. drivers/net/r6040.c: correct bad use of round_jiffies() fec_mpc52xx: MPC52xx_MESSAGES_DEFAULT: 2nd NETIF_MSG_IFDOWN => IFUP ipg: fix receivemode IPG_RM_RECEIVEMULTICAST{,HASH} in ipg_nic_set_multicast_list() netfilter: nf_conntrack: fix ctnetlink related crash in nf_nat_setup_info() netfilter: Make nflog quiet when no one listen in userspace. ipv6: Fail with appropriate error code when setting not-applicable sockopt. ipv6: Check IPV6_MULTICAST_LOOP option value. ipv6: Check the hop limit setting in ancillary data. ipv6 route: Fix route lifetime in netlink message. ipv6 mcast: Check address family of gf_group in getsockopt(MS_FILTER). dccp: Bug in initial acknowledgment number assignment dccp ccid-3: X truncated due to type conversion dccp ccid-3: TFRC reverse-lookup Bug-Fix dccp ccid-2: Bug-Fix - Ack Vectors need to be ignored on request sockets dccp: Fix sparse warnings dccp ccid-3: Bug-Fix - Zero RTT is possible
2008-06-13Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6: sparc: get leo framebuffer working
2008-06-13ahci: Workaround HW bug for SB600/700 SATA controller PMP supportShane Huang
There is one bug in ATI SATA PMP of SB600 and SB700 old revision, which leads to soft reset failure. This patch can fix the bug. Signed-off-by: Shane Huang <shane.huang@amd.com> Acked-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-13ahci: workarounds for mcp65Tejun Heo
MCP65 ahci can do NCQ but doesn't set the CAP bit and rev A0 and A1 can't do MSI but have MSI capability. Implement AHCI_HFLAG_YES_NCQ and apply appropriate workarounds. Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Peer Chen <pchen@nvidia.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-12Merge master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* master.kernel.org:/home/rmk/linux-2.6-arm: [ARM] 5091/1: Add missing bitfield include to regs-lcd.h [ARM] 5090/1: Correct pxafb palette typo error [ARM] 5077/1: spi: fix list scan success verification in PXA ssp driver
2008-06-12rtc: Ramtron FM3130 RTC supportSergey Lapin
Ramtron FM3130 is a chip with two separate devices inside, RTC clock and FRAM. This driver provides only RTC functionality. This chip is met in lots of custom boards with AT91SAMXXXX CPU I work with, is cheap and in no way better or worse than any other RTC on market. While it is mostly met on much smaller devices, I think it is great to have it supported in Linux. Signed-off-by: Sergey Lapin <slapin@ossfans.org> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-12rtc: make HPET_RTC_IRQ track HPET_EMULATE_RTCDavid Brownell
More Kconfig tweaks related to the legacy PC RTC code: - Describe the legacy PC RTC driver as such ... it's never quite been clear that this driver is for PC RTCs, and now it's fair to call this the "legacy" driver. - Force it to understand about HPET stealing its IRQs ... kernel code does this always when HPET is in use, there should be no option for users to goof up the config. This seems to fix kernel bugzilla #10729. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Maxim Levitsky <maximlevitsky@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-12provide rtc_cmos platform deviceStas Sergeev
Recently (around 2.6.25) I've noticed that RTC no longer works for me. It turned out this is because I use pnpacpi=off kernel option to work around the parport_pc bugs. I always did so, but RTC used to work fine in the past, and now it have regressed. The patch fixes the problem by creating the platform device for the RTC when PNP is disabled. This may also help running the PNP-enabled kernel on an older PCs. Signed-off-by: Stas Sergeev <stsp@aknet.ru> Cc: David Brownell <david-b@pacbell.net> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Adam Belay <ambx1@neo.rr.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-12console keyboard mapping broken by 04c71976Jiri Bohac
Several console keyboard maps are broken since commit 04c71976500352d02f60616d2b960267d8c5fe24 Author: Samuel Thibault <samuel.thibault@ens-lyon.org> Date: Tue Oct 16 23:27:04 2007 -0700 unicode diacritics support because that changeset made k_self consider the value as a latin1 character when in Unicode mode, which is wrong; k_self should still take the console map into account. Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-12driver/char/generic_nvram: fix bannerPhilippe De Muyter
The generic nvram driver announces itself as 'Macintosh non-volatile memory driver' instead of 'Generic non-volatile memory driver'. Fix that. Signed-off-by: Philippe De Muyter <phdm@macqel.be> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-12drivers/video/cirrusfb: fix RAM address printkPhilippe De Muyter
In the cirrusfb driver, the RAM address printk has a superfluous 'x' that could be interpreted as "don't care", while it is actually a typo. Fix that. [akpm@linux-foundation.org: join the two printk strings to make it atomic] Signed-off-by: Philippe De Muyter <phdm@macqel.be> Cc: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-12intel_rng: make device not found a warningStephen Hemminger
Since many distros load this driver by default (throw it against the wall and see what sticks method). Change the error message severity level to avoid alarming users. Isn't it annoying when users actually read the error logs... Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Cc: Michael Buesch <mb@bu3sch.de> Acked-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-12drivers/isdn/sc/ioctl.c: add missing kfreeJulia Lawall
spid has been allocated in this function and so should be freed before leaving it, as in the other error handling cases. The semantic match that finds the problem is as follows: (http://www.emn.fr/x-info/coccinelle/) @r exists@ expression E,E1; statement S; position p1,p2,p3; @@ E =@p1 \(kmalloc\|kcalloc\|kzalloc\)(...) ... when != E = E1 if (E == NULL || ...) S ... when != E = E1 if@p2 (...) { ... when != kfree(E) } ... when != E = E1 kfree@p3(E); @forall@ position r.p2; expression r.E; int E1 != 0; @@ * if@p2 (...) { ... when != kfree(E) when strict return E1; } Signed-off-by: Julia Lawall <julia@diku.dk> Cc: Karsten Keil <kkeil@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-12mmc: wbsd: initialize tasklets before requesting interruptChuck Ebbert
With CONFIG_DEBUG_SHIRQ set we will get an interrupt as soon as we allocate one. Tasklets may be scheduled in the interrupt handler but they will be initialized after the handler returns, causing a BUG() in kernel/softirq.c when they run. Should fix this Fedora bug report: https://bugzilla.redhat.com/show_bug.cgi?id=449817 Signed-off-by: Chuck Ebbert <cebbert@redhat.com> Acked-by: Pierre Ossman <drzeus@drzeus.cx> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-12rtc-at32ap700x: fix bug in at32_rtc_readalarm()Haavard Skinnemoen
alarm->pending indicates whether there's an alarm that has actually been triggered, not whether we're waiting for it. alarm->enabled indicates that. Also add missing locking around reading the RTC registers. Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-12cciss: add new hardware supportMike Miller
Add support for the next generation of HP Smart Array SAS/SATA controllers. Shipping date is late Fall 2008. Bump the driver version to 3.6.20 to reflect the new hardware support from patch 1 of this set. Signed-off-by: Mike Miller <mike.miller@hp.com> Cc: Jens Axboe <jens.axboe@oracle.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-12hgafb: resource management fixKrzysztof Helt
Release ports which are requested during detection which are not freed if there is no hga card. Otherwise there is a crash during cat /proc/ioports command. Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-12agp: add support for Radeon Mobility 9000 chipsetAmit Kucheria
Addresses https://bugs.edge.launchpad.net/ubuntu/+source/linux-source-2.6.22/+bug/178634 Signed-off-by: Amit Kucheria <amit.kucheria@ubuntu.com> Signed-off-by: maximilian attems <max@stro.at> Acked-by: Dave Airlie <airlied@linux.ie> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-12bnx2x: Updating the MaintainerEilon Greenstein
I would like to thank Eliezer Tamir for writing and maintaining the driver for the past two years. I will take over maintaining the bnx2x driver from now on. Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: Eliezer Tamir <eliezert@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-12fsl-diu-db: compile fixJeff Mahoney
This patch fixes a compile failure in 2.6.26-rc5-git5. The variable is expected to be called ofdev. Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-12net: Eliminate flush_scheduled_work() calls while RTNL is held.David S. Miller
If the RTNL is held when we invoke flush_scheduled_work() we could deadlock. One such case is linkwatch, it is a work struct which tries to grab the RTNL semaphore. The most common case are net driver ->stop() methods. The simplest conversion is to instead use cancel_{delayed_}work_sync() explicitly on the various work struct the driver uses. This is an OK transformation because these work structs are doing things like resetting the chip, restarting link negotiation, and so forth. And if we're bringing down the device, we're about to turn the chip off and reset it anways. So if we cancel a pending work event, that's fine here. Some drivers were working around this deadlock by using a msleep() polling loop of some sort, and those cases are converted to instead use cancel_{delayed_}work_sync() as well. Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-11drivers/net/r6040.c: correct bad use of round_jiffies()Christophe Jaillet
Compared to other places in the kernel, I think that this driver misuses the function round_jiffies. Signed-off-by: Christophe Jaillet <christophe.jaillet@wanadoo.fr> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-11fec_mpc52xx: MPC52xx_MESSAGES_DEFAULT: 2nd NETIF_MSG_IFDOWN => IFUPRoel Kluin
Duplicate NETIF_MSG_IFDOWN, 2nd should be NETIF_MSG_IFUP Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Sylvain Munaut <tnt@246tNt.com> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-11ipg: fix receivemode IPG_RM_RECEIVEMULTICAST{,HASH} in ↵Roel Kluin
ipg_nic_set_multicast_list() The branches are dead code. even when dev->flag IFF_MULTICAST (defined 0x1000) is set, dev->flags & IFF_MULTICAST & [boolean] always evaluates to 0. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Cc: Francois Romieu <romieu@fr.zoreil.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-11Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: USB: don't use reset-resume if drivers don't support it USB: isp1760: Assign resource fields before adding hcd isight_firmware: Avoid crash on loading invalid firmware USB: fix build bug in USB_ISIGHTFW
2008-06-11Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: kobject: Documentation Spelling Patch dev_set_name: fix missing kernel-doc
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-11-02 15:41:47 +0000