| Age | Commit message (Collapse) | Author |
|---|
|
This patch changes the logic in tx path to ensure that tx descriptors
are reused for transmission only after they have been reclaimed by
arc_emac_tx_clean().
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the current implementation the cleaning of tx ring is done by the
NAPI poll handler, which is scheduled after rx interrupts. Thus, in
absence of received packets the reclaim of used tx buffers is never
executed, blocking further transmission.
This can be easily reproduced starting the transmission of a UDP flow
with iperf, which blocks almost immediately because skbs are not
returned to the stack and the socket send buffer becomes full.
The patch enables tx interrupts so that the tx reclaim is scheduled
after completed transmissions.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We wrongly tested QP context bits without BE conversion
as was spotted by sparse...
drivers/infiniband/hw/mlx4/qp.c:1685:38: sparse: restricted __be32 degrades to integer
Fix that!
Fixes: d2fce8a ('mlx4: Set user-space raw Ethernet QPs to properly handle VXLAN traffic')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changing the vlan stripping policy of the QP isn't supported by older
firmware versions for the INIT2RTR command. Nevertheless, we've used it.
Fix that by doing this policy change using INIT2RTR only if the firmware
supports it, otherwise, we call UPDATE_QP command to do the task.
Fixes: 7677fc9 ('net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current wrapper implementation of the UPDATE_QP command tries to get
the MAC index, even if MAC wasn't set by the VF. Fix it up to only handle
the MAC field if it's valid.
Fixes: ce8d9e0 ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When doing VGT->VST->VGT state changes, we used an incorrect mask
for the vlan-stripping-disable (VSD) flag, hence the vlan related policy
for user-space Raw Ethernet QPs open by VFs wasn't really applied.
Fix that, by using the correct mask.
Fixes: f0f829b ('net/mlx4_core: Add immediate activate for VGT->VST->VGT')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Single port VFs are seen PCI wise on both ports of the PF (we don't have
single port PFs with ConnectX). With this in mind, it's possible for
virtualization tools to try and configure a single ported VF through
the "wrong" PF port.
To handle that, we use the PF driver mapping of single port VFs to NIC
ports and adjust the port value before calling into the low level
code that does the actual VF configuration
Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In Dual EMAC, when both interface are up and while doing ifdown with heavy
traffic then skbs already processed by DMA from that slave emac has to be
requeued as still the other interface is up and running.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds missing space between "interface" and "by"
in bonding module parameter description.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a potential case where we might be failing to refill a
control block, leaving it with both a NULL skb pointer *and* a NULL
dma_unmap_addr.
The way we process incoming packets, by first calling
dma_unmap_single(), and then only checking for a potential NULL skb can
lead to situations where do pass a NULL dma_unmap_addr() to
dma_unmap_single(), resulting in an oops.
Fix this my moving the NULL skb check earlier, since no backing skb
also means no corresponding DMA mapping for this packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a potential case where we might be failing to refill a
control block, leaving it with both a NULL skb pointer *and* a NULL
dma_unmap_addr.
The way we process incoming packets, by first calling
dma_unmap_single(), and then only checking for a potential NULL skb can
lead to situations where do pass a NULL dma_unmap_addr() to
dma_unmap_single(), resulting in an oops.
Fix this my moving the NULL skb check earlier, since no backing skb
also means no corresponding DMA mapping for this packet.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver does not support pause autonegotiation so it should return
-EINVAL when the function is called with non-zero autoneg.
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following compiler warning:
drivers/net/ethernet/octeon/octeon_mgmt.c: In function 'octeon_mgmt_clean_tx_buffers':
drivers/net/ethernet/octeon/octeon_mgmt.c:295:4: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
u64 ns = cvmx_read_csr(CVMX_MIXX_TSTAMP(p->port));
^
Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sunvnet driver does not have an rmb() in the ring consumer corresponding
to the wmb() in the producer. According to Documentation/memory-barriers.txt:
"When dealing with CPU-CPU interactions, certain types of memory barrier should
always be paired. A lack of appropriate pairing is almost certainly an error."
In cases where an rmb() is not a no-op and a consumer is removing data from
the ring while a producer is adding new entries, a load reorder would allow
CPU1 CPU2
---- ----
LOAD desc.size [e.g]
STORE desc.size
<wmb>
set desc.hdr.state = VIO_DESC_READY
LOAD desc.hdr.state
[because VIO_DESC_READY, use
old desc.size, already loaded
out of order]
[CPU2 has reordered apparently unrelated LOADs]
To ensure other desc fields are not loaded before checking VIO_DESC_READY, we
need an rmb() between the check and desc data accesses.
I've also moved the viodbg() call to after the rmb() so that it, too, has
current descriptor data even with reordering, which has the side effect that
it won't print anything for descriptors that are not VIO_DESC_READY as before.
That's a) probably a good thing, since the fields are not necessarily set and,
b) better than adding another rmb() just for viodbg().
This would not be possible if strict-ordering is enforced, but then the
memory barriers should be no-ops in that case.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A bug fix for the vdso code, the loadparm for booting from SCSI is
added and the access permissions for the dasd module parameters are
corrected"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/vdso: remove NULL pointer check from clock_gettime
s390/ipl: Add missing SCSI loadparm attributes to /sys/firmware
s390/dasd: Make module parameter visible in sysfs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Two patches are to add PCI IDs for ICH9 and all others are device
specific fixes. Nothing too interesting"
* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci_xgene: Fix the link down in first attempt for the APM X-Gene SoC AHCI SATA host controller driver.
ahci_xgene: Skip the PHY and clock initialization if already configured by the firmware.
ahci: add pcid for Marvel 0x9182 controller
ata: Disabling the async PM for JMicron chip 363/361
ata_piix: Add Device IDs for Intel 9 Series PCH
ahci: Add Device IDs for Intel 9 Series PCH
ata: ahci_tegra: Read calibration fuse
|
|
Pull networking fixes from David Miller:
1) Fix skb leak in mac802154, from Martin Townsend
2) Use select not depends on NF_NAT for NFT_NAT, from Pablo Neira
Ayuso
3) Fix union initializer bogosity in vxlan, from Gerhard Stenzel
4) Fix RX checksum configuration in stmmac driver, from Giuseppe
CAVALLARO
5) Fix TSO with non-accelerated VLANs in e1000, e1000e, bna, ehea,
i40e, i40evf, mvneta, and qlge, from Vlad Yasevich
6) Fix capability checks in phy_init_eee(), from Giuseppe CAVALLARO
7) Try high order allocations more sanely for SKBs, specifically if a
high order allocation fails, fall back directly to zero order pages
rather than iterating down one order at a time. From Eric Dumazet
8) Fix a memory leak in openvswitch, from Li RongQing
9) amd-xgbe initializes wrong spinlock, from Thomas Lendacky
10) RTNL locking was busted in setsockopt for anycast and multicast, fix
from Sabrina Dubroca
11) Fix peer address refcount leak in ipv6, from Nicolas Dichtel
12) DocBook typo fixes, from Masanari Iida
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
ipv6: restore the behavior of ipv6_sock_ac_drop()
amd-xgbe: Enable interrupts for all management counters
amd-xgbe: Treat certain counter registers as 64 bit
greth: moved TX ring cleaning to NAPI rx poll func
cnic : Cleanup CONFIG_IPV6 & VLAN check
net: treewide: Fix typo found in DocBook/networking.xml
bnx2x: Fix link problems for 1G SFP RJ45 module
3c59x: avoid panic in boomerang_start_xmit when finding page address:
netfilter: add explicit Kconfig for NETFILTER_XT_NAT
ipv6: use addrconf_get_prefix_route() to remove peer addr
ipv6: fix a refcnt leak with peer addr
net-timestamp: only report sw timestamp if reporting bit is set
drivers/net/fddi/skfp/h/skfbi.h: Remove useless PCI_BASE_2ND macros
l2tp: fix race while getting PMTU on PPP pseudo-wire
ipv6: fix rtnl locking in setsockopt for anycast and multicast
VMXNET3: Check for map error in vmxnet3_set_mc
openvswitch: distinguish between the dropped and consumed skb
amd-xgbe: Fix initialization of the wrong spin lock
openvswitch: fix a memory leak
netfilter: fix missing dependencies in NETFILTER_XT_TARGET_LOG
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-09-05
Please pull this batch of fixes intended for the 3.17 stream...
For the mac80211 bits, Johannes says:
"Here are a few fixes for mac80211. One has been discussed for a while
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs."
For the iwlwifi bits, Emmanuel says:
"I revert a patch that disabled CTS to self in dvm because users
reported issues. The revert is CCed to stable since the offending
patch was sent to stable too. I also bump the firmware API versions
since a new firmware is coming up. On top of that, Marcel fixes a
bug I introduced while fixing a bug in our Kconfig file."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are regression fixes (ACPI sysfs, ACPI video, suspend test),
ACPI cpuidle deadlock fix, missing runtime validation of ACPI _DSD
output, a fix and a new CPU ID for the RAPL driver, new blacklist
entry for the ACPI EC driver and a couple of trivial cleanups
(intel_pstate and generic PM domains).
Specifics:
- Fix for recently broken test_suspend= command line argument (Rafael
Wysocki).
- Fixes for regressions related to the ACPI video driver caused by
switching the default to native backlight handling in 3.16 from
Hans de Goede.
- Fix for a sysfs attribute of ACPI device objects that returns stale
values sometimes due to the fact that they are cached instead of
executing the appropriate method (_SUN) every time (broken in
3.14). From Yasuaki Ishimatsu.
- Fix for a deadlock between cpuidle_lock and cpu_hotplug.lock in the
ACPI processor driver from Jiri Kosina.
- Runtime output validation for the ACPI _DSD device configuration
object missing from the support for it that has been introduced
recently. From Mika Westerberg.
- Fix for an unuseful and misleading RAPL (Running Average Power
Limit) domain detection message in the RAPL driver from Jacob Pan.
- New Intel Haswell CPU ID for the RAPL driver from Jason Baron.
- New Clevo W350etq blacklist entry for the ACPI EC driver from Lan
Tianyu.
- Cleanup for the intel_pstate driver and the core generic PM domains
code from Gabriele Mazzotta and Geert Uytterhoeven"
* tag 'pm+acpi-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / cpuidle: fix deadlock between cpuidle_lock and cpu_hotplug.lock
ACPI / scan: not cache _SUN value in struct acpi_device_pnp
cpufreq: intel_pstate: Remove unneeded variable
powercap / RAPL: change domain detection message
powercap / RAPL: add support for CPU model 0x3f
PM / domains: Make generic_pm_domain.name const
PM / sleep: Fix test_suspend= command line option
ACPI / EC: Add msi quirk for Clevo W350etq
ACPI / video: Disable native_backlight on HP ENVY 15 Notebook PC
ACPI / video: Add a disable_native_backlight quirk
ACPI / video: Fix use_native_backlight selection logic
ACPICA: ACPI 5.1: Add support for runtime validation of _DSD package.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"Another round of fixes from arm-soc land, which are mostly DT fixes
for:
- OMAP: handful of DT fixes devices on newly supported hardware
- davinci: fix 2nd EDMA channel
- ux500: extend previous pinctrl fix to another board
- at91: clock registration fixes, compatibility string precision
And one more fix for event cleanup in drivers/bus/arm-ccn"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
bus: arm-ccn: Move event cleanup routine
ARM: at91/dt: rm9200: fix usb clock definition
ARM: at91: rm9200: fix clock registration
ARM: at91/dt: sam9g20: set at91sam9g20 pllb driver
ARM: dts: dra7-evm: Add vtt regulator support
ARM: dts: dra7-evm: Fix spi1 mux documentation
ARM: dts: am43x-epos-evm: Disable QSPI to prevent conflict with GPMC-NAND
ARM: OMAP2+: gpmc: Don't complain if wait pin is used without r/w monitoring
ARM: dts: am43xx-epos-evm: Don't use read/write wait monitoring
ARM: dts: am437x-gp-evm: Don't use read/write wait monitoring
ARM: dts: am437x-gp-evm: Use BCH16 ECC scheme instead of BCH8
ARM: dts: am43x-epos-evm: Use BCH16 ECC scheme instead of BCH8
ARM: dts: am4372: fix USB regs size
ARM: dts: am437x-gp: switch i2c0 to 100KHz
ARM: dts: dra7-evm: Fix 8th NAND partition's name
ARM: dts: dra7-evm: Fix i2c3 pinmux and frequency
ARM: ux500: disable msp2 node on Snowball
ARM: edma: Fix configuration parsing for SoCs with multiple eDMA3 CC
ARM: dts: set 'ti,set-rate-parent' for dpll4_m5x2 clock
|
|
Pull mtd fixes from Brian Norris:
"Two trivial MTD updates for 3.17-rc4:
- a tiny comment tweak, to kill a bunch of DocBook warnings added
during the merge window
- a small fixup to the OTP routines' error handling"
* tag 'for-linus-20140905' of git://git.infradead.org/linux-mtd:
mtd: nand: fix DocBook warnings on nand_sdr_timings doc
mtd: cfi_cmdset_0002: check return code for get_chip()
|
|
As the management counters reach a threshold they will generate an
interrupt so the value can be saved and the counter reset. The
current code does not enable this interrupt on all counters. This
can result in inaccurate statistics.
Update the code to enable all the counters to generate an interrupt
when its threshold is exceeded.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even if the management counters are configured to be 32 bit register
values, the [rt]xoctetcount_gb and [rt]xoctetcount_g counters are
always 64 bit counter registers. Since they are not being treated as
64 bit values, these statistics are being reported incorrectly (ifconfig,
ethtool, etc.).
Update the routines used to read the registers to access the "hi"
register (an offset of 4 from the "lo" register) to create a 64 bit
value for these 64 bit counters.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch does not affect the 10/100 GRETH MAC.
Before all GBit GRETH TX descriptor ring cleaning was done in
start_xmit(), when descriptor list became full it activated
TX interrupt to start the NAPI rx poll function to do TX ring
cleaning.
With this patch the TX descriptor ring is always cleaned from
the NAPI rx poll function, triggered via TX or RX interrupt.
Otherwise we could end up in TX frames being sent but not
reported to the stack being sent. On the 10/100 GRETH this
is not an issue since the SKB is copied&aligned into private
buffers so that the SKB can be freed directly on start_xmit()
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cnic module needs to ensure that if ipv6 support is compiled as a module,
then the cnic module cannot be compiled as built-in as it depends on ipv6.
Made this check cleaner via Kconfig
Use simpler IS_ENABLED for CONFIG_VLAN_8021Q check
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SATA host controller driver.
Due to HW errata the APM X-Gene AHCI SATA host controller reports link
down even if the device presence is detected. This issue is due to speed
negotiation failure. This patch implements the algorithm to retry the
COMRESET if PxSTAT register reports device presence detected but
PHY communication not established. The maximum retry attempts are 3.
This patch also fixes the code to match the algorithm for the printing
a warning message if the disparity error still exists after link up.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
the firmware.
This patch implements the feature to skip the PHY and clock
initialization if it is already configured by the firmware.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
When 1G SFP RJ45 module is detected, driver must reset the Tx laser
in order to prevent link issues. As part of change, the link_attr_sync
was relocated from vars to params.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This bug was reported on a very old kernel (RHEL6, 2.6.32-491.el6):
BUG: unable to handle kernel paging request at 00800000
IP: [<c04107b5>] nommu_map_page+0x15/0x110
*pdpt = 000000003454f001 *pde = 000000003f03d067
Oops: 0000 [#1] SMP
last sysfs file: /sys/devices/system/cpu/online
Modules linked in: nfsd lockd nfs_acl auth_rpcgss sunrpc exportfs p4_clockmod
ipv6 ppdev parport_pc parport microcode iTCO_wdt iTCO_vendor_support 3c59x mii
dcdbas serio_raw snd_intel8x0 snd_ac97_codec ac97_bus snd_seq snd_seq_device
snd_pcm snd_timer snd soundcore snd_page_alloc i2c_i801 sg lpc_ich mfd_core ext4
jbd2 mbcache sr_mod cdrom sd_mod crc_t10dif pata_acpi ata_generic ata_piix
radeon ttm drm_kms_helper drm i2c_algo_bit i2c_core dm_mirror dm_region_hash
dm_log dm_mod [last unloaded: mperf]
Pid: 4219, comm: nfsd Not tainted 2.6.32-491.el6.i686 #1 Dell Computer
Corporation OptiPlex GX240 /OptiPlex GX240
EIP: 0060:[<c04107b5>] EFLAGS: 00010246 CPU: 0
EIP is at nommu_map_page+0x15/0x110
EAX: 00000000 EBX: c0a83480 ECX: 00000000 EDX: 00800000
ESI: 00000000 EDI: f70e7860 EBP: e2d09b54 ESP: e2d09b24
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process nfsd (pid: 4219, ti=e2d08000 task=e2ceaaa0 task.ti=e2d08000)
Stack:
00000056 00000000 0000000e c65efd38 00000020 00000296 00000206 00000206
<0> c050c850 c0a83480 e2cef154 00000001 e2d09ba8 f8fcd585 00000510 00000001
<0> 00000000 00000000 f5172200 f8fdac00 0039ef8c f5277020 f70e7860 00000510
Call Trace:
[<c050c850>] ? page_address+0xd0/0xe0
[<f8fcd585>] ? boomerang_start_xmit+0x3b5/0x520 [3c59x]
[<c07b2975>] ? dev_hard_start_xmit+0xe5/0x400
[<f9182b00>] ? ip6_output_finish+0x0/0xf0 [ipv6]
[<c07ca053>] ? sch_direct_xmit+0x113/0x180
[<c07d5588>] ? nf_hook_slow+0x68/0x120
[<c07b2ea5>] ? dev_queue_xmit+0x1b5/0x290
[<f9182b6d>] ? ip6_output_finish+0x6d/0xf0 [ipv6]
[<f9184cb8>] ? ip6_xmit+0x3e8/0x490 [ipv6]
[<f91ab9f9>] ? inet6_csk_xmit+0x289/0x2f0 [ipv6]
[<c07f6451>] ? tcp_transmit_skb+0x431/0x7f0
[<c07a403f>] ? __alloc_skb+0x4f/0x140
[<c07f85a2>] ? tcp_write_xmit+0x1c2/0xa50
[<c07f90b1>] ? __tcp_push_pending_frames+0x31/0xe0
[<c07ea47a>] ? tcp_sendpage+0x44a/0x4b0
[<c07ea030>] ? tcp_sendpage+0x0/0x4b0
[<c079be1e>] ? kernel_sendpage+0x4e/0x90
[<f8457bb9>] ? svc_send_common+0xc9/0x120 [sunrpc]
[<f8457c85>] ? svc_sendto+0x75/0x1f0 [sunrpc]
[<c060d0d9>] ? _atomic_dec_and_lock+0x59/0x90
[<f87d55d0>] ? nfs3svc_encode_readres+0x0/0xc0 [nfsd]
[<f845876d>] ? svc_authorise+0x2d/0x40 [sunrpc]
[<f87d4410>] ? nfs3svc_release_fhandle+0x0/0x10 [nfsd]
[<f8455721>] ? svc_process_common+0xf1/0x5a0 [sunrpc]
[<f8457e86>] ? svc_tcp_sendto+0x36/0xa0 [sunrpc]
[<f8461778>] ? svc_send+0x98/0xd0 [sunrpc]
[<f87c698c>] ? nfsd+0xac/0x140 [nfsd]
[<c04470e0>] ? complete+0x40/0x60
[<f87c68e0>] ? nfsd+0x0/0x140 [nfsd]
[<c04802ac>] ? kthread+0x7c/0xa0
[<c0480230>] ? kthread+0x0/0xa0
[<c0409f9f>] ? kernel_thread_helper+0x7/0x10
Code: 8d b6 00 00 00 00 eb f8 8d b4 26 00 00 00 00 8d bc 27 00 00 00 00 55 89 e5
83 ec 30 89 75 f8 31 f6 89 7d fc 89 c7 89 c8 89 5d f4 <8b> 1a 8b 4d 08 c1 eb 19
c1 e3 04 8b 9b c0 29 c7 c0 83 e3 fc 29
But the problem seems to still exist upstream. It seems on 32 bit kernels
page_address() can reutrn a NULL value in some circumstances, and the
pci_map_single api isn't prepared to handle that (on this system it results in a
bogus pointer deference in nommu_map_page.
The fix is pretty easy, if we convert the 3c59x driver to use the more
convieient skb_frag_dma_map api we don't need to find the virtual address of the
page at all, and page gets mapped to the hardware properly. Verified to fix the
problem as described by the reporter.
Applies to the net tree
Change Notes:
v2) Converted PCI_DMA_TODEVICE to DMA_TO_DEVICE. Thanks Dave!
v3) Actually Run git commit after making changes to v2 :)
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: klassert@mathematik.tu-chemnitz.de
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
They are use less, and may generate compiling warnings, so remove them
(microblaze, arc, arm64, and unicore32 have already defined PCI_IOBASE).
The related warnings (with allmodconfig under microblaze):
CC [M] drivers/net/fddi/skfp/skfddi.o
In file included from drivers/net/fddi/skfp/skfddi.c:95:0:
drivers/net/fddi/skfp/h/skfbi.h:151:0: warning: "PCI_IOBASE" redefined
#define PCI_IOBASE 0xffffff00L /* Bit 31..8: I/O Base address */
^
In file included from include/linux/io.h:22:0,
from include/linux/pci.h:31,
from drivers/net/fddi/skfp/skfddi.c:82:
./arch/microblaze/include/asm/io.h:33:0: note: this is the location of the previous definition
#define PCI_IOBASE ((void __iomem *)_IO_BASE)
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c bugfixes from Wolfram Sang:
"I2C driver bugfixes for the 3.17 release. Details can be found in the
commit messages, yet I think this is typical driver stuff"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: rcar: remove spinlock"
i2c: at91: add bound checking on SMBus block length bytes
i2c: rk3x: fix bug that cause transfer fails in master receive mode
i2c: at91: Fix a race condition during signal handling in at91_do_twi_xfer.
i2c: mv64xxx: continue probe when clock-frequency is missing
i2c: rcar: fix MNR interrupt handling
|
|
The function cleaning up an initialized event
was called from the "event_del" handler, instead
of being used as the "destroy" callback. In case of
events group allocation this caused NULL pointer
dereference (as events are added and deleted
multiple times then). Fixed now.
Signed-off-by: Pawel Moll <mail@pawelmoll.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
We should check if the map of the table actually succeeds, and also free
resources accordingly.
Version bumped to 1.2.1.0
Acked-by: Shelley Gong <shelleygong@vmware.com>
Acked-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Andy King <acking@vmware.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Keystone K2E EVM uses Marvel 0x9182 controller. This requires support
for the ID in the ahci driver.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
- some documentation sync
- resource leak in the bt8xx driver
- again fix the way varargs are used to handle the optional flags on
the gpiod_* accessors. Now hopefully nailed the entire problem.
* tag 'gpio-v3.17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: move varargs hack outside #ifdef GPIOLIB
gpio: bt8xx: fix release of managed resources
Documentation: gpio: documentation for optional getters functions
|
|
Pull drm fixes from Dave Airlie:
- i915 fixes: a few display regressions
- vmwgfx: possible loop forever fix
- nouveau: one userspace interface fix
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/core: don't leak oclass type bits to user
drm/i915: Fix lock dropping in intel_tv_detect()
drm/i915: handle G45/GM45 pulse detection connected state.
drm/vmwgfx: Fix a potential infinite spin waiting for fifo idle
drm/vmwgfx: Fix an incorrect OOM return value
drm/i915: Remove bogus __init annotation from DMI callbacks
drm/i915: don't warn if backlight unexpectedly enabled
drm/i915: Move intel_ddi_set_vc_payload_alloc(false) to haswell_crtc_disable()
drm/i915: fix plane/cursor handling when runtime suspended
drm/i915: Ignore VBT backlight presence check on Acer C720 (4005U)
|
|
* pm-sleep:
PM / sleep: Fix test_suspend= command line option
* powercap:
powercap / RAPL: change domain detection message
powercap / RAPL: add support for CPU model 0x3f
* pm-domains:
PM / domains: Make generic_pm_domain.name const
* pm-cpufreq:
cpufreq: intel_pstate: Remove unneeded variable
|
|
* acpi-video:
ACPI / video: Disable native_backlight on HP ENVY 15 Notebook PC
ACPI / video: Add a disable_native_backlight quirk
ACPI / video: Fix use_native_backlight selection logic
* acpi-ec:
ACPI / EC: Add msi quirk for Clevo W350etq
|
|
* acpica:
ACPICA: ACPI 5.1: Add support for runtime validation of _DSD package.
* acpi-processor:
ACPI / cpuidle: fix deadlock between cpuidle_lock and cpu_hotplug.lock
* acpi-scan:
ACPI / scan: not cache _SUN value in struct acpi_device_pnp
|
|
git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
single fix for nouveau.
* 'linux-3.17' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/core: don't leak oclass type bits to user
|
|
Fixes not being able to init fence subsystem when multiple boards are
present.
Reported-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
This reverts commit 150b8be3cda54412ad7b54f5392b513b25c0aaa7.
The I2C core's per-adapter locks can't protect from IRQs, so the driver still
needs a spinlock to protect the register accesses.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon bugfix from Guenter Roeck:
"Fix a bug in the ds1621 driver"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ds1621) Update zbits after conversion rate change
|
|
git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform drivers fixes from Darren Hart:
"This is my first pull request since taking on maintenance for the
platform-drivers-x86 tree from Matthew Garrett. These have passed my
build testing and been run through Fengguang's LKP tests. Due to
timing this round, these have not spent any time in linux-next. I
have asked Stephen to include my for-next branch in linux-next going
forward, once he's back from vacation.
Details from tag:
- toshiba_acpi: re-enable hotkeys and cleanups
- ideapad-laptop: revert touchpad disable, and cleanup static/const
usage
- MAINTAINERS: update platform-drivers-x86 maintainer and tree"
* tag 'platform-drivers-x86-v3.17-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
toshiba_acpi: fix and cleanup toshiba_kbd_bl_mode_store()
platform/x86: toshiba: re-enable acpi hotkeys after suspend to disk
ideapad-laptop: Constify DMI table for real!
Revert "ideapad-laptop: Disable touchpad interface on Yoga models"
MAINTAINERS: Update platform-drivers-x86 maintainer and tree
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
here's a couple of display regression fixes for 3.17.
* tag 'drm-intel-fixes-2014-09-03' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix lock dropping in intel_tv_detect()
drm/i915: handle G45/GM45 pulse detection connected state.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem updates from Dmitry Torokhov:
"A fix for MT breakage, enhancement to Elantech PS/2 driver and a
couple of assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add support for trackpoint found on some v3 models
Input: elantech - reset the device when elantech probe fails
Input: ALPS - suppress message about 'Unknown touchpad'
Input: fix used slots detection breakage
Input: sparc - i8042-sparcio.h: fix unused kbd_res warning
Input: atmel_mxt_ts - improve description of gpio-keymap property
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Several bug fixes for issues that have been lurking for a while:
- Check that devices haven't set the flag saying they only support
register at a time operation while we're doing cache syncs,
otherwise we fail to restore caches
- Ensure that we don't mark all registers on devices using
format_write() as cacheable, avoiding adding a cache of things like
reset registers which we don't want to rewrite during cache sync
- Make sure we create the debugfs files in the correct directory"
* tag 'regmap-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Don't attempt block writes when syncing cache on single_rw devices
regmap: Fix handling of volatile registers for format_write() chips
regmap: Fix regcache debugfs initialization
|
|
There is a following AB-BA dependency between cpu_hotplug.lock and
cpuidle_lock:
1) cpu_hotplug.lock -> cpuidle_lock
enable_nonboot_cpus()
_cpu_up()
cpu_hotplug_begin()
LOCK(cpu_hotplug.lock)
cpu_notify()
...
acpi_processor_hotplug()
cpuidle_pause_and_lock()
LOCK(cpuidle_lock)
2) cpuidle_lock -> cpu_hotplug.lock
acpi_os_execute_deferred() workqueue
...
acpi_processor_cst_has_changed()
cpuidle_pause_and_lock()
LOCK(cpuidle_lock)
get_online_cpus()
LOCK(cpu_hotplug.lock)
Fix this by reversing the order acpi_processor_cst_has_changed() does
thigs -- let it first execute the protection against CPU hotplug by
calling get_online_cpus() and obtain the cpuidle lock only after that (and
perform the symmentric change when allowing CPUs hotplug again and
dropping cpuidle lock).
Spotted by lockdep.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The _SUN device indentification object is not guaranteed to return
the same value every time it is executed, so we should not cache its
return value, but rather execute it every time as needed. If it is
cached, an incorrect stale value may be used in some situations.
This issue was exposed by commit 202317a573b2 (ACPI / scan: Add
acpi_device objects for all device nodes in the namespace). Fix it
by avoiding to cache the return value of _SUN.
Fixes: 202317a573b2 (ACPI / scan: Add acpi_device objects for all device nodes in the namespace)
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
