Age | Commit message (Collapse) | Author |
|
Creating a VLAN interface on top of ucc_geth adds 4 bytes
to the frame and the HW controller is not prepared to
TX a frame bigger than 1518 bytes which is 4 bytes too
small for a full VLAN frame. Add 16 bytes which will handle
the a simple VLAN and leaves 12 bytes for future expansion.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a busy network we see ucc_geth is dropping RX pkgs every now
and then. Increase the RX queues HW descriptors from
16 to 32 to deal with this.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here are two EHCI Tegra driver patches for your tree.
The first is a bit big, but the majority is just moving code around.
It is needed due to the other EHCI core changes that went in way back
in 3.4-rc1, so this driver will now properly handle suspend/resume, as
it was broken. The other one is a minor bugfix that resolves an
warning that people have been seeing."
* tag 'usb-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: ehci-tegra: remove redundant gpio_set_value
EHCI: update PM methods in ehci-tegra.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull a TTY fix from Greg Kroah-Hartman:
"This is a deadlock bugfix that was easy to hit, and that the vt layer
lock rework got wrong, so it reverts the logic back to the way it was
in 3.3 and earlier kernels to prevent problems."
* tag 'tty-3.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt: Fix deadlock on scroll-lock
|
|
Match the correct information which is DMI_PRODUCT_NAME instead of DMI_BOARD_NAME
See dmidecode information on launchpad for both thin client:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/911920
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/911916
Signed-off-by: Marc Gariepy <mgariepy@ubuntu.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
On SandyBridge IPS was entirely implemented in hardware and not reliant
on the driver monitoring power consumption and feeding back desired run
states, so the hardware is able to adapt quicker and more flexibly. Which
is a huge relief for us as we no longer have to carry empirically
derived magic algorithms.
Yet despite the advance in technology, the driver was still doing its
IPS polling on all machines. Restrict it to the only supported hardware,
Clarkdale/Arrandale.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49025
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We only execute intel_decrease_pllclock for pre-PCH hardware, typically
gen4 mobiles. However, in the variable declaration we did read from the
non-PCH DPLL register, quite naughty and detected by SandyBridge.
Reported-and-tested-by: Andrey Rahmatullin <wrar@wrar.name>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49025
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
The immediately preceding gpio_direction_output() already set the value,
so there's no need to repeat it. This also prevents gpio_set_value() from
WARNing when the GPIO is sleepable (e.g. is on an I2C expander); the set
direction API is always sleepable, but plain set_value isn't.
Cc: <stable@vger.kernel.org> # v3.3
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1547) rearranges the Power Management parts of the
ehci-tegra driver to match the conventions used in other EHCI platform
drivers. In particular, the controller should not be powered down by
the root hub's suspend routine; the controller's power level should be
managed by the controller's own PM methods.
The end result of the patch is that the standard ehci_bus_suspend()
and ehci_bus_resume() methods can be used instead of special-purpose
routines. The driver now uses the standard dev_pm_ops methods instead
of legacy power management. Since there is no supported wakeup
mechanism for the controller, runtime suspend is forbidden by default
(this can be overridden via sysfs, if desired).
These adjustments are needed in order to make ehci-tegra compatible
with recent changes to the USB core. The core now checks the root
hub's status following bus suspend; if the controller is automatically
powered down during bus suspend then the check will fail and the root
hub will be resumed immediately. Doing the controller power-down in a
separate method avoids this problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixing the locking accidentally replaced a race in the scroll
lock handling with a deadlock. Turn it back into a race for
now.
The basic problem is that there are two paths into the tty
stop/start helpers. One via the tty layer ^S/^Q handling
where we need to take the kbd_event_lock and one via the
special keyboard handler for fn_hold where we already hold
it. Probably we need to split out into a separate LED lock
but for now just go back to the race as it's a bit close
to release.
Reported-by: Clemens Ladisch <clemens@ladisch.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Bug: The VLAN bit of the MAC RX Status Word is unreliable in several older
supported chips. Sometimes the VLAN bit is not set for valid VLAN packets
and also sometimes the VLAN bit is set for non-VLAN packets that came after
a VLAN packet. This results in a receive length error when VLAN hardware
tagging is enabled.
Fix: Variation on original fix proposed by Mirko.
The VLAN information is decoded in the status loop, and can be
applied to the received SKB there. This eliminates the need for the
separate tag field in the interface data structure. The tag has to
be copied and cleared if packet is copied. This version checked out
with vlan and normal traffic.
Note: vlan_tx_tag_present should be renamed vlan_tag_present, but that
is outside scope of this.
Reported-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a small packet is received, the driver copies it to a new skb to allow
reusing the full size Rx buffer. The copy was propogating the checksum offload
but not the receive hash information. The bug is impact was mostly harmless
and therefore not observed until reviewing this area of code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CPU core ID is used to index the core_data[] array. The core ID is, however, not
sequential; 10-core CPUS can have a core ID as high as 25. Increase the limit to
32 to be able to deal with current CPUs.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Durgadoss R <durgadoss.r@intel.com>
|
|
coretemp tries to access core_data array beyond bounds on cpu unplug if
core id of the cpu if more than NUM_REAL_CORES-1.
BUG: unable to handle kernel NULL pointer dereference at 000000000000013c
IP: [<ffffffffa00159af>] coretemp_cpu_callback+0x93/0x1ba [coretemp]
PGD 673e5a067 PUD 66e9b3067 PMD 0
Oops: 0000 [#1] SMP
CPU 79
Modules linked in: sunrpc cpufreq_ondemand acpi_cpufreq freq_table mperf bnep bluetooth rfkill ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 ip6table_filter nf_conntrack_ipv4 nf_defrag_ipv4 ip6_tables xt_state nf_conntrack coretemp crc32c_intel asix tpm_tis pcspkr usbnet iTCO_wdt i2c_i801 microcode mii joydev tpm i2c_core iTCO_vendor_support tpm_bios i7core_edac igb ioatdma edac_core dca megaraid_sas [last unloaded: oprofile]
Pid: 3315, comm: set-cpus Tainted: G W 3.4.0-rc5+ #2 QCI QSSC-S4R/QSSC-S4R
RIP: 0010:[<ffffffffa00159af>] [<ffffffffa00159af>] coretemp_cpu_callback+0x93/0x1ba [coretemp]
RSP: 0018:ffff880472fb3d48 EFLAGS: 00010246
RAX: 0000000000000124 RBX: 0000000000000034 RCX: 00000000ffffffff
RDX: 0000000000000000 RSI: 0000000000000046 RDI: 0000000000000246
RBP: ffff880472fb3d88 R08: ffff88077fcd36c0 R09: 0000000000000001
R10: ffffffff8184bc48 R11: 0000000000000000 R12: ffff880273095800
R13: 0000000000000013 R14: ffff8802730a1810 R15: 0000000000000000
FS: 00007f694a20f720(0000) GS:ffff88077fcc0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 000000000000013c CR3: 000000067209b000 CR4: 00000000000007e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process set-cpus (pid: 3315, threadinfo ffff880472fb2000, task ffff880471fa0000)
Stack:
ffff880277b4c308 0000000000000003 ffff880472fb3d88 0000000000000005
0000000000000034 00000000ffffffd1 ffffffff81cadc70 ffff880472fb3e14
ffff880472fb3dc8 ffffffff8161f48d ffff880471fa0000 0000000000000034
Call Trace:
[<ffffffff8161f48d>] notifier_call_chain+0x4d/0x70
[<ffffffff8107f1be>] __raw_notifier_call_chain+0xe/0x10
[<ffffffff81059d30>] __cpu_notify+0x20/0x40
[<ffffffff815fa251>] _cpu_down+0x81/0x270
[<ffffffff815fa477>] cpu_down+0x37/0x50
[<ffffffff815fd6a3>] store_online+0x63/0xc0
[<ffffffff813c7078>] dev_attr_store+0x18/0x30
[<ffffffff811f02cf>] sysfs_write_file+0xef/0x170
[<ffffffff81180443>] vfs_write+0xb3/0x180
[<ffffffff8118076a>] sys_write+0x4a/0x90
[<ffffffff816236a9>] system_call_fastpath+0x16/0x1b
Code: 48 c7 c7 94 60 01 a0 44 0f b7 ac 10 ac 00 00 00 31 c0 e8 41 b7 5f e1 41 83 c5 02 49 63 c5 49 8b 44 c4 10 48 85 c0 74 56 45 31 ff <39> 58 18 75 4e eb 1f 49 63 d7 4c 89 f7 48 89 45 c8 48 6b d2 28
RIP [<ffffffffa00159af>] coretemp_cpu_callback+0x93/0x1ba [coretemp]
RSP <ffff880472fb3d48>
CR2: 000000000000013c
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
git://git.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nv10/gpio: fix thinko in mask for gpio lines 2-9
nvc0/fb: shut up PMFB interrupt after the first occurrence
drm/nouveau/hdmi: use correct hdmi regs for nvaa/nvac
drm/nouveau/bios: fix regression on some nv4x board
|
|
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' removes the include for
linux/gpio.h from omap-usb-host.c. This include indirectly includes plat/cpu.h
which is required by omap-usb-host.c. Fix the build breakage by including
it directly.
Acked-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The driver calls cxgb_vlan_mode() from init_one(). This calls into
synchronize_rx(), which locks all the q locks, but the q locks are not
initialized until cxgb_up() -> setup_sge_qsets(). So move the call to
cxgb_vlan_mode() into cxgb_up(), after the call to setup_sge_qsets().
We also move the body of these functions up higher to avoid having to
a forward declaration.
This was found because of the lockdep warning:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 323, comm: work_for_cpu Not tainted 3.4.0-rc5 #28
Call Trace:
[<ffffffff8106e767>] register_lock_class+0x108/0x2d0
[<ffffffff8106ff42>] __lock_acquire+0xd3/0xd06
[<ffffffff81070fd0>] lock_acquire+0xbf/0xfe
[<ffffffff813862a6>] _raw_spin_lock_irq+0x36/0x45
[<ffffffffa01e71aa>] cxgb_vlan_mode+0x96/0xcb [cxgb3]
[<ffffffffa01f90eb>] init_one+0x8c4/0x980 [cxgb3]
[<ffffffff811fcbf0>] local_pci_probe+0x3f/0x70
[<ffffffff81042206>] do_work_for_cpu+0x10/0x22
[<ffffffff810482de>] kthread+0xa1/0xa9
[<ffffffff8138e234>] kernel_thread_helper+0x4/0x10
Contrary to what lockdep says, the code is not fine: we are locking an
uninitialized spinlock.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
|
|
With the support to bounce buffer added, the skb is coming as nonlinear in the
case of non-DDPed data frames for FCoE, which is mostly ok as the FCoE stack
would take care of that. However, for target mode, we have to set the FC CRC
and FC EOF field to allow the protocol stack to not drop the frame for the last
data frame of that sequence. So fix this by linearizing the skb first before
doing skb_put().
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The driver was freeing memory in shutdown instead of remove. As a result
we were leaking memory if IEEE DCB was enabled and we loaded/unloaded the
driver. This change moves the freeing of the memory into the remove
routine where it belongs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Maybe it's a typo, but it cause that igbvf can't be initialized successfully.
Set perm_addr value using valid dev_addr, although which is equal to hw.mac.addr.
Signed-off-by: Samuel Liao <samuelliao@tencent.com>
Signed-off-by: Shan Wei <davidshan@tencent.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch sets the automatic speed and duplex detection bits
in MAC_CR to enable the mac to determine its speed automatically
from the phy.
Note this must be done BEFORE the receiver or transmitter is
enabled.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
also explicitly set the phy to advertise 1000 speeds
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
smsc75xx phy interrupt acknowledge needs an mdio_write to clear
PHY_INT_SRC instead of just a read like in smsc95xx.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fix bug in phy_init loop that was ignoring BMCR reset bit, akin to smsc95xx's d946092000698fd204d82a9d239103c656fb63bf
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
smsc75xx needs MII_ACCESS_BUSY to be set to correctly trigger mdio I/O. Note smsc75xx is different from smsc95xx in this regard.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
changes
This patch fixes the same issue as reported on smsc95xx, where the
usb device is connected with no ethernet cable plugged-in.
Without this patch sysfs reports the cable as present
flag@flag-desktop:~$ cat /sys/class/net/eth0/carrier
1
while it's not:
flag@flag-desktop:~$ sudo mii-tool eth0
eth0: no link
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of SAS and SATA fixes; there are one or two longstanding
bug fixes, but most of this is regression fixes."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] libfc: update mfs boundry checking
[SCSI] Revert "[SCSI] libsas: fix sas port naming"
[SCSI] libsas: fix false positive 'device attached' conditions
[SCSI] libsas, libata: fix start of life for a sas ata_port
[SCSI] libsas: fix ata_eh clobbering ex_phys via smp_ata_check_ready
[SCSI] libsas: unify domain_device sas_rphy lifetimes
[SCSI] libsas: fix sas_get_port_device regression
[SCSI] libsas: fix sas_find_bcast_phy() in the presence of 'vacant' phys
[SCSI] libsas: introduce sas_work to fix sas_drain_work vs sas_queue_work
[SCSI] libata: Pass correct DMA device to scsi host
[SCSI] scsi_lib: use correct DMA device in __scsi_alloc_queue
|
|
A common flaw in UEFI systems is a refusal to POST triggered by a malformed
boot variable. Once in this state, machines may only be restored by
reflashing their firmware with an external hardware device. While this is
obviously a firmware bug, the serious nature of the outcome suggests that
operating systems should filter their variable writes in order to prevent
a malicious user from rendering the machine unusable.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a handful more fixes for powerpc. The irq stuff are all
regression fixes, and Gavin's patch is a simple compile fix."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
tty/serial/pmac_zilog: Fix "nobody cared" IRQ message
powerpc/pseries: Rivet CONFIG_EEH for pSeries platform
powerpc/irqdomain: Fix broken NR_IRQ references
powerpc/8xx: Fix NR_IRQ bugs and refactor 8xx interrupt controller
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"A simple fix for a recent regression in Synaptics driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - fix regression with "image sensor" trackpads
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Signed-off-by: Christoph Bumiller <e0425955@student.tuwien.ac.at>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
We started using the connector table on nv4x a while back, and this VBIOS
has bad connector indices which causes the wrong encoders to get paired
with connectors.
Add a quirk to fix this...
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
This replaces the old therm_pm72 using the same windfarm infrastructure
that was used for other PowerMac G5 models. The fan speeds and sensors
should now be visible in the same location in sysfs.
The driver is split into separate core modules for PowerMac7,2 (and 7,3)
and RackMac3,1, with a lot of the shared code now in the separate sensor
and control modules.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The FCU operates the fans on the earlier generation G5 machines,
this module will be used by upcoming windfarm drivers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This allows those modules to load on PowerMac7,2 PowerMac7,3
and RackMac3,1 and add the sensor name conversion for those
machines.
This will be used by the corresponding new windfarm modules
for those machines.
Note that since therm_pm72 is linked first, it will still
take priority on those i2c devices if built-in. If using modules
it will depend which is loaded first, but you should avoid building
therm_pm72 if you are using the new windfarm drivers
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
For use by the upcoming windfarm_rm31
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
For user by the upcoming windfarm_pm72 and windfarm_rm31
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Makes the code more readable
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Controls registered as RPM and PWM fans are now displayed
with the "RPM" or "%" suffix respectively to make it
clearer to the user what the value actually means since
the fan type isn't otherwise obvious.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The windfarm core will do it, so this is a duplicate.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
const'ify the sensor ops and name and add a void* for use by
the control and sensor drivers to point back to their private
data, avoiding the need to create a wrapper data structure
per sensor or control instance.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This simplifies the driver to stop using the deprecated attach interface.
While at it we also implement teardown properly and fix the refcounting
by using a kref.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This simplifies the driver to stop using the deprecated attach interface
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This simplifies the driver to stop using the deprecated attach interface
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This simplifies the driver to stop using the deprecated attach interface,
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|