| Age | Commit message (Collapse) | Author |
|---|
|
Fix a problem in i350 where anti spoofing configuration was written into a
wrong register.
Signed-off-by: Lior Levy <lior.levy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the ixgbevf driver is opened the request to allocate MSIX irq
vectors may fail. In that case the driver will call ixgbevf_down()
which will call ixgbevf_irq_disable() to clear the HW interrupt
registers and calls synchronize_irq() using the msix_entries pointer in
the adapter structure. However, when the function to request the MSIX
irq vectors failed it had already freed the msix_entries which causes
an OOPs from using the NULL pointer in synchronize_irq().
The calls to pci_disable_msix() and to free the msix_entries memory
should not occur if device open fails. Instead they should be called
during device driver removal to balance with the call to
pci_enable_msix() and the call to allocate msix_entries memory
during the device probe and driver load.
Signed-off-by: Li Xun <xunleer.li@huawei.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch removes dynamic allocation on the stack error.
Signed-off-by: Philip J Kelleher <pjk1939@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The Boot ROM has an issue which will cause the driver to
lock up as pending irqs are not being cleared. With them
cleared it prevents that issue.
This patch is needed for the current (3.9-rc3) mainline kernel. I guess
it went unnoticed, because it was only tested with u-boot up until now.
And u-boot maybe handles this.
[s.trumtrar@pengutronix.de: cherry-picked from linux-xlnx.git]
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
They were introduced by mistake in 3.7. Let's deprecate them now. For
the reasons, see the text in Kconfig below.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In 3.7 the 8250 module name was changed unintentionally from 8250 to
8250_core by commit 835d844d1a28efba81d5aca7385e24c29d3a6db2
(8250_pnp: do pnp probe before legacy probe). We then had to
re-introduce the old module options to ensure the old good
8250.nr_uart & co. still work. This can be done only by a very dirty
hack and we did it in f2b8dfd9e480c3db3bad0c25c590a5d11b31f4ef
(serial: 8250: Keep 8250.<xxxx> module options functional after driver
rename).
That is so damn ugly so that I decided to revert to the old module
name and deprecate the new 8250_core options present in 3.7 and 3.8
only. The deprecation will happen in the following patch.
Note that this patch changes the hack above to support "8250_core.*",
because we now have "8250.*" natively.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[Description written by Alan Stern]
Soeren tracked down a very difficult bug in ehci-hcd's DMA pool
management of iTD and siTD structures. Some background: ehci-hcd
gives each isochronous endpoint its own set of active and free itd's
(or sitd's for full-speed devices). When a new itd is needed, it is
taken from the head of the free list, if possible. However, itd's
must not be used twice in a single frame because the hardware
continues to access the data structure for the entire duration of a
frame. Therefore if the itd at the head of the free list has its
"frame" member equal to the current value of ehci->now_frame, it
cannot be reused and instead a new itd is allocated from the DMA pool.
The entries on the free list are not released back to the pool until
the endpoint is no longer in use.
The bug arises from the fact that sometimes an itd can be moved back
onto the free list before itd->frame has been set properly. In
Soeren's case, this happened because ehci-hcd can allocate one more
itd than it actually needs for an URB; the extra itd may or may not be
required depending on how the transfer aligns with a frame boundary.
For example, an URB with 8 isochronous packets will cause two itd's to
be allocated. If the URB is scheduled to start in microframe 3 of
frame N then it will require both itds: one for microframes 3 - 7 of
frame N and one for microframes 0 - 2 of frame N+1. But if the URB
had been scheduled to start in microframe 0 then it would require only
the first itd, which could cover microframes 0 - 7 of frame N. The
second itd would be returned to the end of the free list.
The itd allocation routine initializes the entire structure to 0, so
the extra itd ends up on the free list with itd->frame set to 0
instead of a meaningful value. After a while the itd reaches the head
of the list, and occasionally this happens when ehci->now_frame is
equal to 0. Then, even though it would be okay to reuse this itd, the
driver thinks it must get another itd from the DMA pool.
For as long as the isochronous endpoint remains in use, this flaw in
the mechanism causes more and more itd's to be taken slowly from the
DMA pool. Since none are released back, the pool eventually becomes
exhausted.
This reuslts in memory allocation failures, which typically show up
during a long-running audio stream. Video might suffer the same
effect.
The fix is very simple. To prevent allocations from the pool when
they aren't needed, make sure that itd's sent back to the free list
prematurely have itd->frame set to an invalid value which can never be
equal to ehci->now_frame.
This should be applied to -stable kernels going back to 3.6.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For the s626 driver, there is a bug in the handling of asynchronous
commands on the AI subdevice when the stop source is `TRIG_NONE`. The
command should run continuously until cancelled, but the interrupt
handler stops the command running after the first scan.
The command set-up function `s626_ai_cmd()` contains this code:
switch (cmd->stop_src) {
case TRIG_COUNT:
/* data arrives as one packet */
devpriv->ai_sample_count = cmd->stop_arg;
devpriv->ai_continous = 0;
break;
case TRIG_NONE:
/* continous acquisition */
devpriv->ai_continous = 1;
devpriv->ai_sample_count = 0;
break;
}
The interrupt handler `s626_irq_handler()` contains this code:
if (!(devpriv->ai_continous))
devpriv->ai_sample_count--;
if (devpriv->ai_sample_count <= 0) {
devpriv->ai_cmd_running = 0;
/* ... */
}
So `devpriv->ai_sample_count` is only decremented for the `TRIG_COUNT`
case, but `devpriv->ai_cmd_running` is set to 0 (and the command
stopped) regardless.
Fix this in `s626_ai_cmd()` by setting `devpriv->ai_sample_count = 1`
for the `TRIG_NONE` case. The interrupt handler will not decrement it
so it will remain greater than 0 and the check for stopping the
acquisition will fail.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When config options are:
CONFIG_VIDEO_DEV=y
CONFIG_VIDEO_V4L2=m
CONFIG_I2C=m
Compilation breaks, as reported by:
https://bugzilla.kernel.org/show_bug.cgi?id=55681
Before changeset 7b34be71db533f3e0cf93d53cf62d036cdb5418a,
no compilation errors occurred. However, the I2C code there at
v4l2-device was incorrectly disabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
When a device attached to the roothub is suspended, the endpoint rings
are stopped. The host may generate a completion event with the
completion code set to 'Stopped' or 'Stopped Invalid' when the ring is
halted. The current xHCI code prints a warning in that case, which can
be really annoying if the USB device is coming into and out of suspend.
Remove the unnecessary warning.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Stephen Hemminger <stephen@networkplumber.org>
|
|
Use proper macro while extracting TRB transfer length from
Transfer event TRBs. Adding a macro EVENT_TRB_LEN (bits 0:23)
for the same, and use it instead of TRB_LEN (bits 0:16) in
case of event TRBs.
This patch should be backported to kernels as old as 2.6.31, that
contain the commit b10de142119a676552df3f0d2e3a9d647036c26a "USB: xhci:
Bulk transfer support". This patch will have issues applying to older
kernels.
Signed-off-by: Vivek gautam <gautam.vivek@samsung.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
|
|
This patch is to bind xhci root hub usb port with its acpi node.
The port num in the acpi table matches with the sequence in the xhci
extended capabilities table. So call usb_hcd_find_raw_port_number() to
transfer hub port num into raw port number which associates with
the sequence in the xhci extended capabilities table before binding.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
xhci driver divides the root hub into two logical hubs which work
respectively for usb 2.0 and usb 3.0 devices. They are independent
devices in the usb core. But in the ACPI table, it's one device node
and all usb2.0 and usb3.0 ports are under it. Binding usb port with
its acpi node needs the raw port number which is reflected in the xhci
extended capabilities table. This patch is to add find_raw_port_number
callback to struct hc_driver(), fill it with xhci_find_raw_port_number()
which will return raw port number and add a wrap usb_hcd_find_raw_port_number().
Otherwise, refactor xhci_find_real_port_number(). Using
xhci_find_raw_port_number() to get real index in the HW port status
registers instead of scanning through the xHCI roothub port array.
This can help to speed up.
All addresses in xhci->usb2_ports and xhci->usb3_ports array are
kown good ports and don't include following bad ports in the extended
capabilities talbe.
(1) root port that doesn't have an entry
(2) root port with unknown speed
(3) root port that is listed twice and with different speeds.
So xhci_find_raw_port_number() will only return port num of good ones
and never touch bad ports above.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
/home/b29397/work/code/git/linus/linux-2.6/drivers/usb/host/xhci-ring.c: In function ‘handle_port_status’:
/home/b29397/work/code/git/linus/linux-2.6/drivers/usb/host/xhci-ring.c:1580: warning: ‘hcd’ may be used uninitialized in this function
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma fixes from Roland Dreier:
"Small batch of InfiniBand/RDMA fixes for 3.9:
- Fix for TX lockup in IPoIB
- QLogic -> Intel update for qib driver
- Small static checker fix for qib
- Fix error path return value in cxgb4"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: change QLogic to Intel
IB/ipath: Silence a static checker warning
IPoIB: Fix send lockup due to missed TX completion
RDMA/cxgb4: Fix error return code in create_qp()
|
|
Pull ARM SoC bug fixes from Arnd Bergmann:
"Four patches for arm-soc this week:
- Kevin Hilman is no longer reachable under his previous email
address. He submitted the patch earlier, but nobody felt
responsible to pick it up.
- One Tegra fix for an incorect register address in device tree.
- IMX multiplatform support exposes a configuration option that leads
to unbootable kernels on all other machines and that needs to
depend on that platform.
- A nontrivial bug fix for the setup of the mxs video output."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: update email address for Kevin Hilman
ARM: tegra: fix register address of slink controller
ARM: imx: add dependency check for DEBUG_IMX_UART_PORT
ARM: video: mxs: Fix mxsfb misconfiguring VDCTRL0
|
|
With the addition of following patch:
fcf8058 cpufreq: Simplify cpufreq_add_dev()
cpufreq driver's .init() routine must initialize policy->cpus with
mask of all possible CPUs (Online + Offline) that share the clock.
Then the core would copy this mask onto policy->related_cpus and will
reset policy->cpus to carry only online cpus.
acpi-cpufreq driver wasn't updated with this assumption and so
sometimes when we try to hot[un]plug CPUs at run time, sysfs
directories get corrupted.
This patch fixes acpi-cpufreq driver against this corruption.
Reported-and-tested-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In cpufreq_stats_free_sysfs() we aren't balancing calls to
cpufreq_cpu_get() with cpufreq_cpu_put(). This will never let us have
ref count to policy->kobj as zero.
We will get a hang if somehow cpufreq_driver_unregister() is called.
And that can happen when we compile our driver as module and
insmod/rmmod it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
They are defined in coreboot (MSR_PLATFORM) and the other
one is already defined in msr-index.h.
Let's use those.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use the correct pstate value to calculate the effective frequency.
References: https://bugzilla.redhat.com/show_bug.cgi?id=923942
Reported-by: Satish Balay <balay@fastmail.fm>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Some VMs seem to try to implement some MSRs but not all the registers
the driver needs. Check to make sure all the MSR that we need are
available. If any of the required MSRs are not available refuse to
load.
References: https://bugzilla.redhat.com/show_bug.cgi?id=922923
Reported-by: Josh Stone <jistone@redhat.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull drm fixes from Dave Airlie:
"Exynos and Intel fixes.
The intel fixes are fairly straightforward, mostly reverts due to bugs
found. The exynos one is a big larger since they found some issues
with the G2D engine and iommu interaction, and needed to verify the
operations a lot better than they were previously, otherwise a user
app can just crash the kernel with an iommu fault."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "drm/i915: write backlight harder"
drm/i915: don't disable the power well yet
Revert "drm/i915: set TRANSCODER_EDP even earlier"
drm/exynos: Check g2d cmd list for g2d restrictions
drm/exynos: Add a new function to get gem buffer size
drm/exynos: Deal with g2d buffer info more efficiently
drm/exynos: Clean up some G2D codes for readability
drm/exynos: Fix G2D core malfunctioning issue
drm/exynos: clear node object type at gem unmap
drm/exynos: Fix error routine to getting dma addr.
drm/exynos: Replaced kzalloc & memcpy with kmemdup
drm/exynos: fimd: calculate the correct address offset
drm/exynos: Make mixer_check_timing static
drm/exynos: modify the compatible string for exynos fimd
|
|
git://people.freedesktop.org/~danvet/drm-intel into HEAD
Daniel writes:
"Just three revert/disable by default patches, one of them cc: stable
(since the offending commit was cc: stable, too)."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
Revert "drm/i915: write backlight harder"
drm/i915: don't disable the power well yet
Revert "drm/i915: set TRANSCODER_EDP even earlier"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into HEAD
Inki writes:
Includes bug fixes and code cleanups.
And it considers some restrictions to G2D hardware.
With this, the malfunction and page fault issues to g2d driver
would be fixed.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: Check g2d cmd list for g2d restrictions
drm/exynos: Add a new function to get gem buffer size
drm/exynos: Deal with g2d buffer info more efficiently
drm/exynos: Clean up some G2D codes for readability
drm/exynos: Fix G2D core malfunctioning issue
drm/exynos: clear node object type at gem unmap
drm/exynos: Fix error routine to getting dma addr.
drm/exynos: Replaced kzalloc & memcpy with kmemdup
drm/exynos: fimd: calculate the correct address offset
drm/exynos: Make mixer_check_timing static
drm/exynos: modify the compatible string for exynos fimd
|
|
fix for incorrect assignment of signed expression to unsigned variable.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"Here are a few pinctrl fixes for the v3.9 rc series:
- Usecount bounds checking so we do not go below zero on mux
usecounts.
- Loop range checking in GPIO ranges in the DT range parser.
- Proper print in debugfs for pinconf state.
- Fix compilation bug in generic pinconf code.
- Minor bugfixes to abx500 and mvebu drivers."
* tag 'pinctrl-fixes-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinmux: forbid mux_usecount to be set at UINT_MAX
pinctrl: mvebu: fix checking for SoC specific controls
pinctrl: generic: Fix compilation error
pinctrl: Print the correct information in debugfs pinconf-state file
pinctrl: abx500: Fix checking if pin use AlternateFunction register
gpio: fix wrong checking condition for gpio range
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"A collection of minor fixes, more EFI variables paranoia
(anti-bricking) plus the ability to disable the pstore either as a
runtime default or completely, due to bricking concerns."
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efivars: Fix check for CONFIG_EFI_VARS_PSTORE_DEFAULT_DISABLE
x86, microcode_intel_early: Mark apply_microcode_early() as cpuinit
efivars: Handle duplicate names from get_next_variable()
efivars: explicitly calculate length of VariableName
efivars: Add module parameter to disable use as a pstore backend
efivars: Allow disabling use as a pstore backend
x86-32, microcode_intel_early: Fix crash with CONFIG_DEBUG_VIRTUAL
x86-64: Fix the failure case in copy_user_handle_tail()
|
|
This reverts commit cf0a6584aa6d382f802f2c3cacac23ccbccde0cd.
Turns out that cargo-culting breaks systems. Note that we can't revert
further, since
commit 770c12312ad617172b1a65b911d3e6564fc5aca8
Author: Takashi Iwai <tiwai@suse.de>
Date: Sat Aug 11 08:56:42 2012 +0200
drm/i915: Fix blank panel at reopening lid
fixed a regression in 3.6-rc kernels for which we've never figured out
the exact root cause. But some further inspection of the backlight
code reveals that it's seriously lacking locking. And especially the
asle backlight update is know to get fired (through some smm magic)
when writing specific backlight control registers. So the possibility
of suffering from races is rather real.
Until those races are fixed I don't think it makes sense to try
further hacks. Which sucks a bit, but sometimes that's how it is :(
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18788.html
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47941
Tested-by: Takashi Iwai <tiwai@suse.de>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: stable@vger.kernel.org (the reverted commit was cc: stable, too)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
We're still not 100% ready to disable the power well, so don't disable
it for now. When we disable it we break the audio driver (because some
of the audio registers are on the power well) and machines with eDP on
port D (because it doesn't use TRANSCODER_EDP).
Also, instead of just reverting the code, add a Kernel option to let
us disable it if we want. This will allow us to keep developing and
testing the feature while it's not enabled.
This fixes problems caused by the following commit:
commit d6dd9eb1d96d2b7345fe4664066c2b7ed86da898
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jan 29 16:35:20 2013 -0200
drm/i915: dynamic Haswell display power well support
References: http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18788.html
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This reverts commit cc464b2a17c59adedbdc02cc54341d630354edc3.
The reason is that Takashi Iwai reported a regression bisected to this
commit:
http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg18788.html
His machine has eDP on port D (usual desktop all-in-on setup), which
intel_dp.c identifies as an eDP panel, but the hsw ddi code
mishandles.
Closer inspection of the code reveals that haswell_crtc_mode_set also
checks intel_encoder_is_pch_edp when setting is_cpu_edp. On haswell
that doesn't make much sense (since there's no edp on the pch), but
what this function _really_ checks is whether that edp connector is on
port A or port D. It's just that on ilk-ivb port D was on the pch ...
So that explains why this seemingly innocent change killed eDP on port
D. Furthermore it looks like everything else accidentally works, since
we've never enabled eDP on port D support for hsw intentionally (e.g.
we still register the HDMI output for port D in that case).
But in retrospective I also don't like that this leaks highly platform
specific details into common code, and the reason is that the drm
vblank layer sucks. So instead I think we should:
- move the cpu_transcoder into the dynamic pipe_config tracking (once
that's merged).
- fix up the drm vblank layer to finally deal with kms crtc objects
instead of int pipes.
v2: Pimp commit message with the better diagnosis as discussed with
Paulo on irc.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"These are mostly minor fixes this time around. The iscsi-target CHAP
big-endian bugfix and bump FD_MAX_SECTORS=2048 default patch to allow
1MB sized I/Os for FILEIO backends on >= v3.5 code are both CC'ed to
stable.
Also, there is a persistent reservations regression that has recently
been reported for >= v3.8.x code, that is currently being tracked down
for v3.9."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/pscsi: Reject cross page boundary case in pscsi_map_sg
target/file: Bump FD_MAX_SECTORS to 2048 to handle 1M sized I/Os
tcm_vhost: Flush vhost_work in vhost_scsi_flush()
tcm_vhost: Add missed lock in vhost_scsi_clear_endpoint()
target: fix possible memory leak in core_tpg_register()
target/iscsi: Fix mutual CHAP auth on big-endian arches
target_core_sbc: use noop for SYNCHRONIZE_CACHE
|
|
Pull md fixes from NeilBrown:
"A few bugfixes for md
- recent regressions in raid5
- recent regressions in dmraid
- a few instances of CONFIG_MULTICORE_RAID456 linger
Several tagged for -stable"
* tag 'md-3.9-fixes' of git://neil.brown.name/md:
md: remove CONFIG_MULTICORE_RAID456 entirely
md/raid5: ensure sync and DISCARD don't happen at the same time.
MD: Prevent sysfs operations on uninitialized kobjects
MD RAID5: Avoid accessing gendisk or queue structs when not available
md/raid5: schedule_construction should abort if nothing to do.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata updates from Jeff Garzik:
"Simple stuff. See one-line summaries."
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_samsung_cf: use module_platform_driver_probe()
[libata] Avoid specialized TLA's in ZPODD's Kconfig
libata-acpi.c: fix copy and paste mistake in ata_acpi_register_power_resource
sata_fsl: Remove redundant NULL check before kfree
ahci: Add Device IDs for Intel Wellsburg PCH
ata_piix: Add MODULE_PARM_DESC to prefer_ms_hyperv
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"One bugfix for the tegra driver. Two updates regarding email
addresses and MAINTAINERS which I like to have up-to-date so people
can be reached immediately. While we are here, there is on PCI_ID
addition."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: add maintainer entry for atmel i2c driver
i2c: Fix my e-mail address in drivers and documentation
i2c: iSMT: add Intel Avoton DeviceIDs
i2c: tegra: check the clk_prepare_enable() return value
|
|
Pull watchdog fixes from Wim Van Sebroeck:
"Fix a boot issues and correct the AcpiMmioSel bitmask in the
sp5100_tco watchdog device driver"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: sp5100_tco: Set the AcpiMmioSel bitmask value to 1 instead of 2
watchdog: sp5100_tco: Remove code that may cause a boot failure
|
|
When KMS has parsed an EDID "detailed timing", it leaves the frame rate
zeroed. Consecutive (debug-) output of that mode thus yields 0 for
vsync. This simple fix also speeds up future invocations of
drm_mode_vrefresh().
While it is debatable whether this qualifies as a -stable fix I'd apply
it for consistency's sake; drm_helper_probe_single_connector_modes()
does the same thing already for all probed modes.
Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
EDID spreads some values across multiple bytes; bit-fiddling is needed
to retrieve these. The current code to parse "detailed timings" has a
cut&paste error that results in a vsync offset of at most 15 lines
instead of 63.
See
http://en.wikipedia.org/wiki/EDID
and in the "EDID Detailed Timing Descriptor" see bytes 10+11 show why
that needs to be a left shift.
Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
These changes modify the qib driver as part of acquiring
the InfiniBand assets of QLogic.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Vinit Agnihotri <vinit.abhay.agnihotri@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
I have a static checker which complains that 0x255 is too high for
the "dev->opstats[opcode]" array. It turns out that the hardware
has already validated the opcode at this point so it can't actually
overflow.
However, silencing the warning is good and this matches how the
opcode is treated in qib_ib_rcv() as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Commit f0dc117abdfa ("IPoIB: Fix TX queue lockup with mixed UD/CM
traffic") attempts to solve an issue where unprocessed UD send
completions can deadlock the netdev.
The patch doesn't fully resolve the issue because if more than half
the tx_outstanding's were UD and all of the destinations are RC
reachable, arming the CQ doesn't solve the issue.
This patch uses the IB_CQ_REPORT_MISSED_EVENTS on the
ib_req_notify_cq(). If the rc is above 0, the UD send cq completion
callback is called directly to re-arm the send completion timer.
This issue is seen in very large parallel filesystem deployments
and the patch has been shown to correct the issue.
Cc: <stable@vger.kernel.org>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Fix to return a negative error code from the error handling case
instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Pull NVMe driver update from Matthew Wilcox:
"These patches have mostly been baking for a few months; sorry I didn't
get them in during the merge window. They're all bug fixes, except
for the addition of the SMART log and the addition to MAINTAINERS."
* git://git.infradead.org/users/willy/linux-nvme:
NVMe: Add namespaces with no LBA range feature
MAINTAINERS: Add entry for the NVMe driver
NVMe: Initialize iod nents to 0
NVMe: Define SMART log
NVMe: Add result to nvme_get_features
NVMe: Set result from user admin command
NVMe: End queued bio requests when freeing queue
NVMe: Free cmdid on nvme_submit_bio error
|
|
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mqueue: sys_mq_open: do not call mnt_drop_write() if read-only
mm/hotplug: only free wait_table if it's allocated by vmalloc
dma-debug: update DMA debug API to better handle multiple mappings of a buffer
dma-debug: fix locking bug in check_unmap()
drivers/rtc/rtc-at91rm9200.c: use a variable for storing IMR
drivers/video/ep93xx-fb.c: include <linux/io.h> for devm_ioremap()
drivers/rtc/rtc-da9052.c: fix for rtc device registration
mm: zone_end_pfn is too small
poweroff: change orderly_poweroff() to use schedule_work()
mm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting
printk: Provide a wake_up_klogd() off-case
irq_work.h: fix warning when CONFIG_IRQ_WORK=n
|
|
On some revisions of AT91 SoCs, the RTC IMR register is not working.
Instead of elaborating a workaround for that specific SoC or IP version,
we simply use a software variable to store the Interrupt Mask Register
and modify it for each enabling/disabling of an interrupt. The overhead
of this is negligible anyway.
The interrupt mask register (IMR) for the RTC is broken on the AT91SAM9x5
sub-family of SoCs (good overview of the members here:
http://www.eewiki.net/display/linuxonarm/AT91SAM9x5 ). The "user visible
effect" is the RTC doesn't work.
That sub-family is less than two years old and only has devicetree (DT)
support and came online circa lk 3.7 . The dust is yet to settle on the
DT stuff at least for AT91 SoCs (translation: lots of stuff is still
broken, so much that it is hard to know where to start).
The fix in the patch is pretty simple: just shadow the silicon IMR
register with a variable in the driver. Some older SoCs (pre-DT) use the
the rtc-at91rm9200 driver (e.g. obviously the AT91RM9200) and they should
not be impacted by the change. There shouldn't be a large volume of
interrupts associated with a RTC.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit be8678149701 ("drivers/video/ep93xx-fb.c: use devm_ functions")
introduced a build error:
drivers/video/ep93xx-fb.c: In function 'ep93xxfb_probe':
drivers/video/ep93xx-fb.c:532: error: implicit declaration of function 'devm_ioremap'
drivers/video/ep93xx-fb.c:533: warning: assignment makes pointer from integer without a cast
Include <linux/io.h> to pickup the declaration of 'devm_ioremap'.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Cc: Damien Cassou <damien.cassou@lifl.fr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add support for the virtual irq since now MFD only handles virtual irq
Without this patch rtc device will fail in registration.
(akpm: Ashish has a different version whcih will be needed for 3.8.x and
earlier kernels)
Signed-off-by: Ashish <ashish.jangam@kpitcummins.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The AcpiMmioSel bit is bit 1 in the AcpiMmioEn register, but the current
sp5100_tco driver is using bit 2.
See 2.3.3 Power Management (PM) Registers page 150 of the
AMD SB800-Series Southbridges Register Reference Guide [1].
AcpiMmioEn - RW – 8/16/32 bits - [PM_Reg: 24h]
Field Name Bits Default Description
AcpiMMioDecodeEn 0 0b Set to 1 to enable AcpiMMio space.
AcpiMMIoSel 1 0b Set AcpiMMio registers to be memory-mapped or IO-mapped space.
0: Memory-mapped space
1: I/O-mapped space
The sp5100_tco driver expects zero as a value of AcpiMmioSel (bit 1).
Fortunately, no problems were caused by this typo, because the default
value of the undocumented misused bit 2 seems to be zero.
However, the sp5100_tco driver should use the correct bitmask value.
[1] http://support.amd.com/us/Embedded_TechDocs/45482.pdf
Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
|
|
A problem was found on PC's with the SB700 chipset: The PC fails to
load BIOS after running the 3.8.x kernel until the power is completely
cut off. It occurs in all 3.8.x versions and the mainline version as of
2/4. The issue does not occur with the 3.7.x builds.
There are two methods for accessing the watchdog registers.
1. Re-programming a resource address obtained by allocate_resource()
to chipset.
2. Use the direct memory-mapped IO access.
The method 1 can be used by all the chipsets (SP5100, SB7x0, SB8x0 or
later). However, experience shows that only PC with the SB8x0 (or
later) chipsets can use the method 2.
This patch removes the method 1, because the critical problem was found.
That's why the watchdog timer was able to be used on SP5100 and SB7x0
chipsets until now.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1116835
Link: https://lkml.org/lkml/2013/2/14/271
Signed-off-by: Takahisa Tanaka <mc74hc00@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
|
