| Age | Commit message (Collapse) | Author |
|---|
|
Fix endianess bugs in firmware handling introduced by commits cb7a7c6a
("ti_usb_3410_5052: add Multi-Tech modem support") and 05a3d905
("ti_usb_3410_5052: support alternate firmware") which made the driver
use the wrong firmware for certain devices on big-endian machines.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure the reported device-type on big-endian machines is the same as
on little-endian ones.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix probe of Rigol devices on big-endian machines. A quirk for these
devices was introduced by commit c2e314835 ("USB: usbtmc: Set
rigol_quirk if device is listed") but was only enabled on little-endian
machines.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix bug in device-type detection on big-endian machines originally
introduced by commit 0eafe4de ("USB: serial: mos7840: add support for
MCS7810 devices") which always matched on little-endian product ids.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes an issue where the bulk-in urb used for incoming data transfer
is not resubmitted if the packet recieved contains an error status. This
results in the driver locking until the port is closed and re-opened.
Tested on a custom board with a Cinterion GSM module.
Signed-off-by: Matt Burtch <matt@grid-net.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes a kernel panic that can occur when disconnecting a
wireless USB->serial device. When the serial device disconnects, the
device cleanup procedure ends up calling usb_hcd_disable_endpoint on the
serial device's endpoints. The wusbcore uses the ABORT_RPIPE command to
abort all transfers on the given endpoint but it does not properly give
back the URBs when the transfer results return from the HWA. This patch
prevents the transfer result processing code from bailing out when it sees
a WA_XFER_STATUS_ABORTED result code so that these urbs are flushed
properly by usb_hcd_disable_endpoint. It also updates wa_urb_dequeue to
handle the case where the endpoint has already been cleaned up when
usb_kill_urb is called which is where the panic originally occurred.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commits 4005ad4390bf (EHCI: implement new semantics for
URB_ISO_ASAP) and c75c5ab575af (ALSA: USB: adjust for changed 3.8 USB
API) became widely distributed, people have been experiencing problems
with audio transfers. The slightest underrun causes complete failure,
requiring the audio stream to be restarted.
It turns out that the current isochronous API doesn't handle underruns
in the best way. The ALSA developers would much rather have transfers
that are submitted too late be accepted and complete in the normal
fashion, rather than being refused outright.
This patch implements the requested approach. When an isochronous URB
submission is so late that all its scheduled slots have already
expired, a debugging message will be printed in the log and the URB
will be accepted as usual. Assuming it was submitted by a completion
handler (which is normally the case), it will complete shortly
thereafter with all the usb_iso_packet_descriptor status fields marked
-EXDEV.
This fixes (for ehci-hcd)
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1191603
It should be applied to all kernels that include commit 4005ad4390bf.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Maksim Boyko <maksboyko@yandex.ru>
CC: Clemens Ladisch <clemens@ladisch.de>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix possibly wrong memcpy() bytes length since some CAN records received from
PCAN-USB could define a DLC field in range [9..15].
In that case, the real DLC value MUST be used to move forward the record pointer
but, only 8 bytes max. MUST be copied into the data field of the struct
can_frame object of the skb given to the network core.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit ac4e4af1e59e1 ("macvtap: Consistently use rcu functions"),
Thomas gets two different warnings :
BUG: using smp_processor_id() in preemptible [00000000] code: vhost-45891/45892
caller is macvtap_do_read+0x45c/0x600 [macvtap]
CPU: 1 PID: 45892 Comm: vhost-45891 Not tainted 3.11.0-bisecttest #13
Call Trace:
([<00000000001126ee>] show_trace+0x126/0x144)
[<00000000001127d2>] show_stack+0xc6/0xd4
[<000000000068bcec>] dump_stack+0x74/0xd8
[<0000000000481066>] debug_smp_processor_id+0xf6/0x114
[<000003ff802e9a18>] macvtap_do_read+0x45c/0x600 [macvtap]
[<000003ff802e9c1c>] macvtap_recvmsg+0x60/0x88 [macvtap]
[<000003ff80318c5e>] handle_rx+0x5b2/0x800 [vhost_net]
[<000003ff8028f77c>] vhost_worker+0x15c/0x1c4 [vhost]
[<000000000015f3ac>] kthread+0xd8/0xe4
[<00000000006934a6>] kernel_thread_starter+0x6/0xc
[<00000000006934a0>] kernel_thread_starter+0x0/0xc
And
BUG: using smp_processor_id() in preemptible [00000000] code: vhost-45897/45898
caller is macvlan_start_xmit+0x10a/0x1b4 [macvlan]
CPU: 1 PID: 45898 Comm: vhost-45897 Not tainted 3.11.0-bisecttest #16
Call Trace:
([<00000000001126ee>] show_trace+0x126/0x144)
[<00000000001127d2>] show_stack+0xc6/0xd4
[<000000000068bdb8>] dump_stack+0x74/0xd4
[<0000000000481132>] debug_smp_processor_id+0xf6/0x114
[<000003ff802b72ca>] macvlan_start_xmit+0x10a/0x1b4 [macvlan]
[<000003ff802ea69a>] macvtap_get_user+0x982/0xbc4 [macvtap]
[<000003ff802ea92a>] macvtap_sendmsg+0x4e/0x60 [macvtap]
[<000003ff8031947c>] handle_tx+0x494/0x5ec [vhost_net]
[<000003ff8028f77c>] vhost_worker+0x15c/0x1c4 [vhost]
[<000000000015f3ac>] kthread+0xd8/0xe4
[<000000000069356e>] kernel_thread_starter+0x6/0xc
[<0000000000693568>] kernel_thread_starter+0x0/0xc
2 locks held by vhost-45897/45898:
#0: (&vq->mutex){+.+.+.}, at: [<000003ff8031903c>] handle_tx+0x54/0x5ec [vhost_net]
#1: (rcu_read_lock){.+.+..}, at: [<000003ff802ea53c>] macvtap_get_user+0x824/0xbc4 [macvtap]
In the first case, macvtap_put_user() calls macvlan_count_rx()
in a preempt-able context, and this is not allowed.
In the second case, macvtap_get_user() calls
macvlan_start_xmit() with BH enabled, and this is not allowed.
Reported-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Bisected-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Cc: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is three bug fixes: An fnic warning caused by sleeping under a
lock, a major regression with our updated WRITE SAME/UNMAP logic which
caused tons of USB devices (and one RAID card) to cease to function
and a megaraid_sas firmware initialisation problem which causes kdump
failures"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] Don't attempt to send extended INQUIRY command if skip_vpd_pages is set
[SCSI] fnic: BUG: sleeping function called from invalid context during probe
[SCSI] megaraid_sas: megaraid_sas driver init fails in kdump kernel
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some driver bugfixes for the I2C subsystem"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mv64xxx: Document the newly introduced allwinner compatible
i2c: Fix Kontron PLD prescaler calculation
i2c: i2c-mxs: Use DMA mode even for small transfers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are 3 small fixes for staging/IIO drivers for 3.11-rc5. Nothing
huge, two IIO driver fixes, and a zcache fix. All of these have been
in linux-next for a while"
* tag 'staging-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: zcache: fix "zcache=" kernel parameter
iio: ti_am335x_adc: Fix wrong samples received on 1st read
iio:trigger: Fix use_count race condition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are 3 small USB fixes for 3.11-rc5.
One is a fix that the ChromeOS developers ran into on some Intel
hardware, one is a build fix, and the last is a MAINTAINERS update to
help people figure out where to send USB network driver patches.
All of these have been in linux-next for a while"
* tag 'usb-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
MAINTAINERS: Add separate section for USB NETWORKING DRIVERS
usb: xhci: add missing dma-mapping.h includes
usb: core: don't try to reset_device() a port that got just disconnected
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- ACPI-based memory hotplug stopped working after a recent change,
because it's not possible to associate sufficiently many "physical"
devices with one ACPI device object due to an artificial limit. Fix
from Rafael J Wysocki removes that limit and makes memory hotplug
work again.
- A change made in 3.9 uncovered a bug in the ACPI processor driver
preventing NUMA nodes from being put offline due to an ordering
issue. Fix from Yasuaki Ishimatsu changes the ordering to make
things work again.
- One of the recent ACPI video commits (that hasn't been reverted so
far) uncovered a bug in the code handling quirky BIOSes that caused
some Asus machines to boot with backlight completely off which made
it quite difficult to use them afterward. Fix from Felipe Contreras
improves the quirk to cover this particular case correctly.
- A cpufreq user space interface change made in 3.10 inadvertently
renamed the ignore_nice_load sysfs attribute to ignore_nice which
resulted in some confusion. Fix from Viresh Kumar changes the name
back to ignore_nice_load.
- An initialization ordering change made in 3.9 broke cpufreq on
loongson2 boards. Fix from Aaro Koskinen restores the correct
initialization ordering there.
- Fix breakage resulting from a mistake made in 3.9 and causing the
detection of some graphics adapters (that were detected correctly
before) to fail. There are two objects representing the same PCIe
port in the affected systems' ACPI tables and both appear as
"enabled" and we are expected to guess which one to use. We used to
choose the right one before by pure luck, but when we tried to
address another similar corner case, the luck went away. This time
we try to make our guessing a bit more educated which is reported to
work on those systems.
- The /proc/acpi/wakeup interface code is missing some locking which
may lead to breakage if that file is written or read during hotplug
of wakeup devices. That should be rare but still possible, so it's
better to start using the appropriate locking there.
* tag 'pm+acpi-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: Try harder to resolve _ADR collisions for bridges
cpufreq: rename ignore_nice as ignore_nice_load
cpufreq: loongson2: fix regression related to clock management
ACPI / processor: move try_offline_node() after acpi_unmap_lsapic()
ACPI: Drop physical_node_id_bitmap from struct acpi_device
ACPI / PM: Walk physical_node_list under physical_node_lock
ACPI / video: improve quirk check in acpi_video_bqc_quirk()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix bug in adt7470 driver which causes it to fail writing fan speed
limits"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (adt7470) Fix incorrect return code check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some driver fixes (em28xx, coda, usbtv, s5p, hdpvr and ml86v7667) and
a fix for media DocBook"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] em28xx: fix assignment of the eeprom data
[media] hdpvr: fix iteration over uninitialized lists in hdpvr_probe()
[media] usbtv: fix dependency
[media] usbtv: Throw corrupted frames away
[media] usbtv: Fix deinterlacing
[media] v4l2: added missing mutex.h include to v4l2-ctrls.h
[media] DocBook: upgrade media_api DocBook version to 4.2
[media] ml86v7667: fix compile warning: 'ret' set but not used
[media] s5p-g2d: Fix registration failure
[media] media: coda: Fix DT driver data pointer for i.MX27
[media] s5p-mfc: Fix input/output format reporting
|
|
This patch fixed the condition of extend_desc for jumbo frame.
There is no check routine for extend_desc in the stmmac_jumbo_frm function.
Even though extend_desc is set if dma_tx is used instead of dma_etx.
It causes kernel panic.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fix from Jiri Kosina:
"Revert of a patch which breaks enumeration workaround in
hid-logitech-dj"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
Revert "HID: hid-logitech-dj: querying_devices was never set"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
- omapdss: compilation fix and DVI fix for PandaBoard
- mxsfb: fix colors when using 18bit LCD bus
* tag 'fbdev-fixes-3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
ARM: OMAP: dss-common: fix Panda's DVI DDC channel
video: mxsfb: fix color settings for 18bit data bus and 32bpp
OMAPDSS: analog-tv-connector: compile fix
|
|
Pull drm fixes from Dave Airlie:
"Mostly radeon, more fixes for dynamic power management which is is off
by default for this release anyways, but there are a large number of
testers, so I'd like to keep merging the fixes.
Otherwise, radeon UVD fixes affecting suspend/resume regressions, i915
regression fixes, one for your mac mini, ast, mgag200, cirrus ttm fix
and one regression fix in the core"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (25 commits)
drm: Don't pass negative delta to ktime_sub_ns()
drm/radeon: make missing smc ucode non-fatal
drm/radeon/dpm: require rlc for dpm
drm/radeon/cik: use a mutex to properly lock srbm instanced registers
drm/radeon: remove unnecessary unpin
drm/radeon: add more UVD CS checking
drm/radeon: stop sending invalid UVD destroy msg
drm/radeon: only save UVD bo when we have open handles
drm/radeon: always program the MC on startup
drm/radeon: fix audio dto calculation on DCE3+ (v3)
drm/radeon/dpm: disable sclk ss on rv6xx
drm/radeon: fix halting UVD
drm/radeon/dpm: adjust power state properly for UVD on SI
drm/radeon/dpm: fix spread spectrum setup (v2)
drm/radeon/dpm: adjust thermal protection requirements
drm/radeon: select audio dto based on encoder id for DCE3
drm/radeon: properly handle pm on gpu reset
drm/i915: do not disable backlight on vgaswitcheroo switch off
drm/i915: Don't call encoder's get_config unless encoder is active
drm/i915: avoid brightness overflow when doing scale
...
|
|
This is a regression introduced by:
commit fe5c3561e6f0ac7c9546209f01351113c1b77ec8
Author: stephen hemminger <stephen@networkplumber.org>
Date: Sat Jul 13 10:18:18 2013 -0700
vxlan: add necessary locking on device removal
The problem is that vxlan_dellink(), which is called with RTNL lock
held, tries to flush the workqueue synchronously, but apparently
igmp_join and igmp_leave work need to hold RTNL lock too, therefore we
have a soft lockup!
As suggested by Stephen, probably the flush_workqueue can just be
removed and let the normal refcounting work. The workqueue has a
reference to device and socket, therefore the cleanups should work
correctly.
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Tested-by: Cong Wang <amwang@redhat.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a regression introduced by:
commit 3fc2de2faba387218bdf9dbc6b13f513ac3b060a
Author: stephen hemminger <stephen@networkplumber.org>
Date: Thu Jul 18 08:40:15 2013 -0700
vxlan: fix igmp races
Before this commit, the old code was:
if (vxlan_group_used(vn, vxlan->default_dst.remote_ip))
ip_mc_join_group(sk, &mreq);
else
ip_mc_leave_group(sk, &mreq);
therefore we shoud check vxlan_group_used(), not its opposite,
for igmp_join.
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduced in cf3c4c03060b688cbc389ebc5065ebcce5653e96
("8139cp: Add dma_mapping_error checking")
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 407a2c2a4d85100c8c67953e4bac2f4a6c942335.
Explanation provided by Benjamin Tissoires:
Commit "HID: hid-logitech-dj, querying_devices was never set" activate
a flag which guarantees that we do not ask the receiver for too many
enumeration. When the flag is set, each following enumeration call is
discarded (the usb request is not forwarded to the receiver). The flag
is then released when the driver receive a pairing information event,
which normally follows the enumeration request.
However, the USB3 bug makes the driver think the enumeration request
has been forwarded to the receiver. However, it is actually not the
case because the USB stack returns -EPIPE. So, when a new unknown
device appears, the workaround consisting in asking for a new
enumeration is not working anymore: this new enumeration is discarded
because of the flag, which is never reset.
A solution could be to trigger a timeout before releasing it, but for
now, let's just revert the patch.
Reported-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Tested-by: Sune Mølgaard <sune@molgaard.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://people.freedesktop.org/~danvet/drm-intel into drm-fixes
Daniel writes:
A few bugfixes for serious stuff and regressions. Highlight is the
reinstated hack to keep the i915 backlight on when running on an optimus
machine, this prevents black screens especially with some radeon muxed
platforms. And the patch to quiet dmesg on Linus' old mac mini ;-)
* tag 'drm-intel-fixes-2013-08-08' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: do not disable backlight on vgaswitcheroo switch off
drm/i915: Don't call encoder's get_config unless encoder is active
drm/i915: avoid brightness overflow when doing scale
drm/i915: update last_vblank when disabling the power well
drm/i915: fix gen4 digital port hotplug definitions
|
|
In adt7470_write_word_data(), which writes two bytes using
i2c_smbus_write_byte_data(), the return codes are incorrectly AND-ed
together when they should be OR-ed together.
The return code of i2c_smbus_write_byte_data() is zero for success.
The upshot is only the first byte was ever written to the hardware.
The 2nd byte was never written out.
I noticed that trying to set the fan speed limits was not working
correctly on my system. Setting the fan speed limits is the only
code that uses adt7470_write_word_data(). After making the change
the limit settings work and the alarms work also.
Signed-off-by: Curt Brune <curt@cumulusnetworks.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Two things here, one is a fix for a nasty issue where we were failing
to sync the last register in a block when using raw writes and the
other fixes a missing header for the !REGMAP stubs so that we don't
rely on implicit includes in that case"
* tag 'regmap-v3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Add missing header for !CONFIG_REGMAP stubs
regmap: cache: Make sure to sync the last register in a block
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fix from Mark Brown:
"Just one update for SPI, a simple fix to the davinci driver to correct
the direction for which DMA is mapped following the dmaengine
conversion"
* tag 'spi-v3.11-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-davinci: Fix direction in dma_map_single()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio fixes from Rusty Russell:
"More virtio console fixes than I'm happy with, but all real issues,
and all CC:stable.."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio-scsi: Fix virtqueue affinity setup
virtio: console: return -ENODEV on all read operations after unplug
virtio: console: fix raising SIGIO after port unplug
virtio: console: clean up port data immediately at time of unplug
virtio: console: fix race in port_fops_open() and port unplug
virtio: console: fix race with port unplug and open/close
virtio/console: Add pipe_lock/unlock for splice_write
virtio/console: Quit from splice_write if pipe->nrbufs is 0
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
- MSM: GPIO fixes (includes old code removal)
- OMAP: earlyprintk regression, AM33xx cpgmac PM regression
- OMAP5: urgent fix for potentially harmful voltage regulator values
- Renesas: gpio-keys fix, fix SD card detection, fix shdma calculation
error
- STi: critical SMP boot fix
- tegra: DTS fix for usb-phy
- a couple MAINTAINERS updates
(Arnd is on paternity leave, Kevin is stepping up to help arm-soc
maintenance)
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: add TI Keystone ARM platform
MAINTAINERS: delete Srinidhi from ux500
ARM: tegra: enable ULPI phy on Colibri T20
ARM: STi: remove sti_secondary_start from INIT section.
ARM: STi: Fix cpu nodes with correct device_type.
ARM: shmobile: lager: do not annotate gpio_buttons as __initdata
ARM: shmobile: BOCK-W: fix SDHI0 PFC settings
shdma: fixup sh_dmae_get_partial() calculation error
ARM: OMAP2+: hwmod: AM335x: fix cpgmac address space
ARM: OMAP2+: hwmod: rt address space index for DT
ARM: OMAP2+: Sync hwmod state with the pm_runtime and omap_device state
ARM: OMAP2+: Avoid idling memory controllers with no drivers
ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL
ARM: dts: omap5-uevm: update optional/unused regulator configurations
ARM: dts: omap5-uevm: fix regulator configurations mandatory for SoC
ARM: dts: omap5-uevm: document regulator signals used on the actual board
ARM: msm: Consolidate gpiomux for older architectures
ARM: shmobile: armadillo800eva: Don't request GPIO 166 in board code
ARM: msm: dts: Fix the gpio register address for msm8960
|
|
It takes an unsigned value. This happens not to blow up on 64-bit
architectures, but it does on 32-bit, causing
drm_calc_vbltimestamp_from_scanoutpos() to calculate totally bogus
timestamps for vblank events. Which in turn causes e.g. gnome-shell to
hang after a DPMS off cycle with current xf86-video-ati Git.
[airlied: regression introduced in drm: use monotonic time in drm_calc_vbltimestamp_from_scanoutpos]
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59339
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59836
Tested-by: shui yangwei <yangweix.shui@intel.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Some more radeon fixes. Mostly dpm and uvd fixes. Fixes hangs
with dpm on more rv6xx asics, and fixes suspend and resume with UVD.
* 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: make missing smc ucode non-fatal
drm/radeon/dpm: require rlc for dpm
drm/radeon/cik: use a mutex to properly lock srbm instanced registers
drm/radeon: remove unnecessary unpin
drm/radeon: add more UVD CS checking
drm/radeon: stop sending invalid UVD destroy msg
drm/radeon: only save UVD bo when we have open handles
drm/radeon: always program the MC on startup
drm/radeon: fix audio dto calculation on DCE3+ (v3)
drm/radeon/dpm: disable sclk ss on rv6xx
drm/radeon: fix halting UVD
drm/radeon/dpm: adjust power state properly for UVD on SI
drm/radeon/dpm: fix spread spectrum setup (v2)
drm/radeon/dpm: adjust thermal protection requirements
drm/radeon: select audio dto based on encoder id for DCE3
drm/radeon: properly handle pm on gpu reset
|
|
The smc ucode is required for dpm (dynamic power
management), but if it's missing just skip dpm setup
and don't disable acceleration.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=67876
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The rlc is required for dpm to work properly, so if
the rlc ucode is missing, don't enable dpm. Enabling
dpm without the rlc enabled can result in hangs.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We need proper locking in the driver when accessing instanced
registers on CIK.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We don't pin the BO on allocation, so don't unpin it on free.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Improve error handling in case userspace sends us
an invalid command buffer.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We also need to check the handle.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Otherwise just reinitialize from scratch on resume,
and so make it more likely to succeed.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For r6xx+ asics. This mirrors the behavior of pre-r6xx
asics. We need to program the MC even if something
else in startup() fails. Failure to do so results in
an unusable GPU.
Based on a fix from: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Need to set the wallclock ratio and adjust the phase
and module registers appropriately. May fix problems
with audio timing at certain display timings.
v2: properly handle clocks below 24mhz
v3: rebase r600 changes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Enabling spread spectrum on the engine clock
leads to hangs on some asics.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=66963
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Removing the clock/power or resetting the VCPU can cause
hangs if that happens in the middle of a register write.
Stall the memory and register bus before putting the VCPU
into reset. Keep it in reset when unloading the module or
suspending.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There are some hardware issue with reclocking on SI when
UVD is active, so use a stable power state when UVD is
active. Fixes possible hangs and performance issues when
using UVD on SI.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Need to check for engine and memory clock ss separately
and only enable dynamic ss if either of them are found.
This should fix systems which have a ss table, but do
not have entries for engine or memory. On those systems
we may enable dynamic spread spectrum without enabling
it on the engine or memory clocks which can lead to a
hang in some cases.
fixes some systems reported here:
https://bugs.freedesktop.org/show_bug.cgi?id=66963
v2: fix typo
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
On rv770 and newer, clock gating is not required
for thermal protection. The only requirement is that
the design utilizes a thermal sensor.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There are two audio dtos on radeon asics that you can
select between. Normally, dto0 is used for hdmi and
dto1 for DP, but it seems that the dto is somehow
tied to the encoders on DCE3 asics.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=67435
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
When we reset the GPU, we need to properly tear
down power management before reseting the GPU and then
set it back up again after reset. Add the missing
radeon_pm_[suspend|resume] calls to the gpu reset
function.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
* pm-fixes:
cpufreq: rename ignore_nice as ignore_nice_load
cpufreq: loongson2: fix regression related to clock management
|
