| Age | Commit message (Collapse) | Author |
|---|
|
The link may be up already via the chip's reset strapping, or though action
of U-Boot, or from the last time the interface was brought up. Resetting
the link causes it to go down for several seconds. This can significantly
increase the time from power-on to DHCP completion and a device being
accessible to the network.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The init_phy() function attaches to the PHY, then configures the
SerDes<->TBI link (in SGMII mode). The TBI is on the MDIO bus with the PHY
(sort of) and is accessed via the gianfar's MDIO registers, using the
functions gfar_local_mdio_read/write(), which don't do any locking.
The previously attached PHY will start a work-queue on a timer, and
probably an irq handler as well, which will talk to the PHY and thus use
the MDIO bus. This uses phy_read/write(), which have locking, but not
against the gfar_local_mdio versions.
The result is that PHY code will try to use the MDIO bus at the same time
as the SerDes setup code, corrupting the transfers.
Setting up the SerDes before attaching to the PHY will insure that there is
no race between the SerDes code and *our* PHY, but doesn't fix everything.
Typically the PHYs for all gianfar devices are on the same MDIO bus, which
is associated with the first gianfar device. This means that the first
gianfar's SerDes code could corrupt the MDIO transfers for a different
gianfar's PHY.
The lock used by phy_read/write() is contained in the mii_bus structure,
which is pointed to by the PHY. This is difficult to access from the
gianfar drivers, as there is no link between a gianfar device and the
mii_bus which shares the same MDIO registers. As far as the device layer
and drivers are concerned they are two unrelated devices (which happen to
share registers).
Generally all gianfar devices' PHYs will be on the bus associated with the
first gianfar. But this might not be the case, so simply locking the
gianfar's PHY's mii bus might not lock the mii bus that the SerDes setup
code is going to use.
We solve this by having the code that creates the gianfar platform device
look in the device tree for an mdio device that shares the gianfar's
registers. If one is found the ID of its platform device is saved in the
gianfar's platform data.
A new function in the gianfar mii code, gfar_get_miibus(), can use the bus
ID to search through the platform devices for a gianfar_mdio device with
the right ID. The platform device's driver data is the mii_bus structure,
which the SerDes setup code can use to lock the current bus.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
When the at91_ether driver is using a GPIO for its PHY interrupt,
be sure to request (and later, if needed, free) that GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Acoording commit aa24886e379d2b641c5117e178b15ce1d5d366ba,
dma_free_coherent() need irqs enabled.
This patch fix following warning messages:
WARNING: at linux/arch/x86/kernel/pci-dma.c:376 dma_free_coherent+0xaa/0xb0()
Call Trace:
[<ffffffff8023f80f>] warn_on_slowpath+0x5f/0x90
[<ffffffff80496ffa>] ? __kfree_skb+0x3a/0xa0
[<ffffffff802a4723>] ? discard_slab+0x23/0x40
[<ffffffff8021274a>] dma_free_coherent+0xaa/0xb0
[<ffffffff8043668f>] amd8111e_close+0x10f/0x1b0
[<ffffffff8049f3ae>] dev_close+0x5e/0xb0
[<ffffffff8049efa1>] dev_change_flags+0xa1/0x1e0
[<ffffffff806b2171>] ic_close_devs+0x36/0x4e
[<ffffffff806b29ee>] ip_auto_config+0x581/0x10f3
[<ffffffff803a6e19>] ? kobject_add+0x69/0x90
[<ffffffff803a698a>] ? kobject_get+0x1a/0x30
[<ffffffff803a785b>] ? kobject_uevent+0xb/0x10
[<ffffffff803a6c62>] ? kset_register+0x52/0x60
[<ffffffff803a6f9b>] ? kset_create_and_add+0x6b/0xa0
[<ffffffff804e2e74>] ? tcp_ca_find+0x24/0x50
[<ffffffff806b246d>] ? ip_auto_config+0x0/0x10f3
[<ffffffff8020903c>] _stext+0x3c/0x150
[<ffffffff802772d3>] ? register_irq_proc+0xd3/0xf0
[<ffffffff802f0000>] ? mb_cache_create+0x80/0x1f0
[<ffffffff80688693>] kernel_init+0x141/0x1b8
[<ffffffff80688552>] ? kernel_init+0x0/0x1b8
[<ffffffff8020d609>] child_rip+0xa/0x11
[<ffffffff80688552>] ? kernel_init+0x0/0x1b8
[<ffffffff80688552>] ? kernel_init+0x0/0x1b8
[<ffffffff8020d5ff>] ? child_rip+0x0/0x11
Signed-off-by: Chunbo Luo <chunbo.luo@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Commit 401c0aabec4b97320f962a0161a846d230a6f7aa introduced a regression
in the atl1 driver by storing the VLAN tag in the wrong TX descriptor
field.
This patch causes the VLAN tag to be stored in its proper location.
Tested-by: Ramon Casellas <ramon.casellas@cttc.es>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Use mmiowb() to ensure "stop" and "go" commands are sent in order on ia64.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
A panic was discovered with bonding when using mode 5 or 6 and trying to
remove the slaves from the bond after the interface was taken down.
When calling 'ifconfig bond0 down' the following happens:
bond_close()
bond_alb_deinitialize()
tlb_deinitialize()
kfree(bond_info->tx_hashtbl)
bond_info->tx_hashtbl = NULL
Unfortunately if there are still slaves in the bond, when removing the
module the following happens:
bonding_exit()
bond_free_all()
bond_release_all()
bond_alb_deinit_slave()
tlb_clear_slave()
tx_hash_table = BOND_ALB_INFO(bond).tx_hashtbl
u32 next_index = tx_hash_table[index].next
As you might guess we panic when trying to access a few entries into the
table that no longer exists.
I experimented with several options (like moving the calls to
tlb_deinitialize somewhere else), but it really makes the most sense to
be part of the bond_close routine. It also didn't seem logical move
tlb_clear_slave around too much, so the simplest option seems to add a
check in tlb_clear_slave to make sure we haven't already wiped the
tx_hashtbl away before searching for all the non-existent hash-table
entries that used to point to the slave as the output interface.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch reworks the resource free logic performed at the time
a bonding device is released. This (a) closes two resource leaks, one
for workqueues and one for multicast lists, and (b) improves commonality
of code between the "destroy one" and "destroy all" paths by performing
final free activity via destructor instead of explicitly (and differently)
in each path.
"Sean E. Millichamp" <sean@bruenor.org> reported the workqueue
leak, and included a different patch.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
During the rework of the mii monitor for:
commit f0c76d61779b153dbfb955db3f144c62d02173c2
Author: Jay Vosburgh <fubar@us.ibm.com>
Date: Wed Jul 2 18:21:58 2008 -0700
bonding: refactor mii monitor
I left out the increment of the link failure counter. This
patch corrects that omission.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The amd8111e rx poll routine currently mishandles the case when we
process exactly the number of packets specified in the budget.
This patch is basically as suggested by David Miller.
Signed-off-by: Chris Friesen <cfriesen@nortel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
|
|
On Saturday 25 October 2008 10:24:10 Johannes Berg wrote:
> just FYI in case you haven't seen them. the p54 one looks like a genuine
> problem.
>
> drivers/net/wireless/p54/p54common.c: In function ‘p54_parse_eeprom’:
> drivers/net/wireless/p54/p54common.c:325: warning: ‘synth’ may be used uninitialized in this function
There you go. Yes, it is a genuine problem, if the device's eeprom is screwed really up.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
After a s2ram / resume cycle, resetting the key cache does not work
unless it is deferred until after the hardware has been reinitialised by
a call to ath5k_hw_reset(). This fixes a regression introduced by
"ath5k: fix suspend-related oops on rmmod".
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes a double-free error in p54pci
( http://bugzilla.kernel.org/show_bug.cgi?id=11782 )
Trying to free already-free IRQ 10
Pid: 108, comm: pccardd Not tainted 2.6.27-05577-g0cfd810-dirty #1
Call Trace:
[<c01265dc>] free_irq+0xad/0xb9
[<c01050dd>] dma_generic_alloc_coherent+0x0/0xd7
[<c01ba8e6>] p54p_stop+0x4a/0x1fa
[<c01050dd>] dma_generic_alloc_coherent+0x0/0xd7
[<c02348c5>] p54p_probe+0x23e/0x302
Tested-by: Sean Young
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Implement set_mac_address for runtime mac address change.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
This patch corrects a message bug in the via-velocity driver which
bothered me for some time.
The messages printed during device init look like the following:
[ 8.486422] eth%d: set value of parameter Wake On Lan options to 0
^^!
[ 8.487340] eth0: VIA Networking Velocity Family Gigabit Ethernet Adapter
Note the unresolved format string.
dev->name is unavailable before register_netdev, so use
dev_driver_string(&pdev->dev), which is also consistent with other
drivers.
"char *devname" parameters had to be converted to "const char *devname" to
be consistent with dev_driver_string return value.
Signed-off-by: Sven Hartge <sven@svenhartge.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Fix !CONFIG_INET warnings.
Spotted, and original patch authored by: Manish Katiyar <mkatiyar@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Removed duplicated #include <linux/cpumask.h> in
drivers/net/mlx4/en_main.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
The recent build fix for ibm_newemac has a typo in the config
option #ifdef used for disabling flow control. This corrects
it to the proper Kconfig option name.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
All kernel memory which is used for kernel/hardware data transfer must
be registered with firmware using "memory regions". 16GB hugepages
may not be part of a memory region due to firmware restrictions.
This patch modifies the walk_memory_resource callback fn to filter
hugepages and add only standard memory to the busmap which is later
on used for MR registration.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
We need to check the address that pci_alloc_consistent() returns since
it might fail.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
To make the qeth driver more robust in case of malformatted inbound
packets due to hardware problems, an additional check for
OSN-card-type is added for OSN-type packets.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Removing this check improves usability because you do not have to
set the device online to initially set ipv6 routing option.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
For the non preallocated qeth header code path we should not
change the header length.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
IP-threads have been removed from the qeth driver. Only the
recover-thread is left over. This makes checkings for
non-recover threads superfluous.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
free sk_buff with kfree_skb, instead of kree
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
free sk_buff with kfree_skb, instead of kree
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* 'for-linus' of git://neil.brown.name/md:
md: allow extended partitions on md devices.
md: use sysfs_notify_dirent to notify changes to md/dev-xxx/state
md: use sysfs_notify_dirent to notify changes to md/array_state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - add support for Elantech touchpads
Input: i8042 - add Blue FB5601 to noloop exception table
|
|
* 'for-linus' of git://git.o-hand.com/linux-mfd:
mfd: Make WM8400 depend on I2C until SPI is submitted
mfd: add missing Kconfig entry for da903x
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
uwb: build UWB before USB/WUSB
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Add support for Sony Vaio VGX-TP1E
HID: fix lock imbalance in hiddev
HID: fix lock imbalance in hidraw
HID: fix hidbus/appletouch device binding regression
HID: add hid_type to general hid struct
HID: quirk for OLED devices present in ASUS G50/G70/G71
HID: Remove "default m" for Thrustmaster and Zeroplus
HID: fix hidraw_exit section mismatch
HID: add support for another Gyration remote control
Revert "HID: Invert HWHEEL mappings for some Logitech mice"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
leds-hp-disk: fix build warning
ACPI: Oops in ACPI with git latest
ACPI suspend: build fix for ACPI_SLEEP=n && XEN_SAVE_RESTORE=y.
toshiba_acpi: always call input_sync() after input_report_switch()
ACPI: Always report a sync event after a lid state change
ACPI: cpufreq, processor: fix compile error in drivers/acpi/processor_perflib.c
i7300_idle: Fix compile warning CONFIG_I7300_IDLE_IOAT_CHANNEL not defined
i7300_idle: Cleanup based review comments
i7300_idle: Disable ioat channel only on platforms where ile driver can load
|
|
If CONFIG_AMIGA_BUILTIN_SERIAL=m, I get the following warnings:
| drivers/char/amiserial.c: At top level:
| drivers/char/amiserial.c:2138: warning: data definition has no type or storage class
| drivers/char/amiserial.c:2138: warning: type defaults to 'int' in declaration of 'console_initcall'
| drivers/char/amiserial.c:2138: warning: parameter names (without types) in function declaration
| drivers/char/amiserial.c:2134: warning: 'amiserial_console_init' defined but not used
because console_initcall() is not defined (nor really sensible) in the
modular case.
So disable serial console support if the driver is modular.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (abituguru3) enable DMI probing feature on AW9D-MAX
hwmon: (abituguru3) Cosmetic whitespace fixes
hwmon: (adt7473) Fix voltage conversion routines
hwmon: (lm90) Add support for the LM99 16 degree offset
hwmon: (lm90) Fix handling of hysteresis value
hwmon-vid: Add support for AMD family 10h CPUs
hwmon: (w83781d) Fix linking when built-in
|
|
This reverts commit 7bf6bf4803df1adc927f585168d2135fb019c698.
The code has both a short existence and an increasing track of failures
despite some work to amend it for -rc1. It is not just a matter of
reading the eeprom: sometimes the eeprom is read correctly, then the mac
address is not written correctly back into the mac registers.
Some chipsets seem to work reliably but it is not clear at this point if
the code can simply be made to work on a per-chipset basis and post -rc1
is not the place where I want to experiment these things.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
a) semicolon before the function body is a bad idea
b) it's const struct foo, not struct const foo
c) incidentally, it's ecard_remove_driver(), not ecard_unregister_driver()
d) compiling is occasionally useful.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Switch the AW9D-MAX over from port probing to the preferred DMI
probe method.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
As the probable result of zealous copy/pasting, many supported boards
contain sensor names with trailing whitespace. Though this is not a
huge problem, it is inconsistent with other sensor names, and with
other similar hwmon drivers.
Additionally, the DMI nag message added in 2.6.27 was missing a
space between two sentence fragments -- might as well clean that up
too.
Doesn't alter any kernel text, just data.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Fix voltage conversion routines. Based on an earlier patch from
Paulius Zaleckas.
According to the datasheet voltage is scaled with resistors and
value 192 is nominal voltage. 0 is 0V.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Darrick J. Wong <djwong@us.ibm.com>
|
|
The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
|
|
There are several problems in the way the hysteresis value is handled
by the lm90 driver:
* In show_temphyst(), specific handling of the MAX6646 is missing, so
the hysteresis is reported incorrectly if the critical temperature
is over 127 degrees C.
* In set_temphyst(), the new hysteresis register value is written to
the chip but data->temp_hyst isn't updated accordingly, so there is
a short period of time (up to 2 seconds) where the old hystereris
value will be returned while the new one is already active.
* In set_temphyst(), the critical temperature which is used as a base
to compute the value of the hysteresis register lacks
device-specific handling. As a result, the value of the hysteresis
register might be incorrect for the ADT7461 and MAX6646 chips.
Fix these 3 bugs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Nate Case <ncase@xes-inc.com>
|
|
The AMD family 10h CPUs use the same VID decoding table as the family
0Fh CPUs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
|
|
When w83781d is built-in, the final links fails with the following vague error
message:
`.exit.text' referenced in section `.init.text' of drivers/built-in.o: defined
in discarded section `.exit.text' of drivers/built-in.o
w83781d_isa_unregister() cannot be marked __exit, as it's also called from
sensors_w83781d_init(), which is marked __init.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
|
|
drivers/leds/leds-hp-disk.c:59: warning: passing argument 4 of ‘acpi_evaluate_integer’ from incompatible pointer type
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
ACPI Warning (nseval-0168): Insufficient arguments - method [_OSC] needs 5, found 4 [20080926]
ACPI Warning (nspredef-0252): \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, expected 4 [20080926]
ACPI Error (nspredef-0163): \_SB_.PCI0._OSC: Missing expected return value [20080926]
BUG: unable to handle kernel NULL pointer dereference at 00000000
IP: [<c0237671>] acpi_run_osc+0xa1/0x170
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
