| Age | Commit message (Collapse) | Author |
|---|
|
Fixes sysfs config attribute to allow access to entire 16MB maintenance
space of RapidIO devices.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Initialize ts_real.flags to fix compiler warning about possible
uninitialized use of this field.
Signed-off-by: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In linux rtc_time struct, tm_mon range is 0~11, tm_wday range is 0~6,
while in RTC HW REG, month range is 1~12, day of the week range is 1~7,
this patch adjusts difference of them.
The efect of this bug was that most of month will be operated on as the
next month by the hardware (When in Jan it maybe even worse). For
example, if in May, software wrote 4 to the hardware, which handled it as
April. Then the logic would be different between software and hardware,
which would cause weird things to happen.
Signed-off-by: Lei Xu <B33228@freescale.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Jack Lan <jack.lan@freescale.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The regulator framework is used for power management. The regulators are
only named in the driver code, the actual control stuff is in the board
file for each architecture or use case.
The PN544 chip has three regulators that can be controlled or not -
depending on the architecture where the chip is being used. So some of
the regulators may not be controllable. In our current case the third
regulator, which was missing from the code, went unnoticed because we
didn't need to control it. To be as general as possible - in this respect
- the driver needs to list all regulators. Then the board file can be
used to actually set the usage.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Spell out the NFC acronym when it's shown for the first time.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator, mc13xxx: Remove pointless test for unsigned less than zero
regulator: Fix warning with CONFIG_BUG disabled
|
|
The member of the rtc_class_ops struct is called alarm_irq_enable and
not alarm_irq_enabled
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jelle Martijn Kok <jmkok@youcom.nl>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
usb: musb: core: set has_tt flag
USB: xhci: mark local functions as static
USB: xhci: fix couple sparse annotations
USB: xhci: rework xhci_print_ir_set() to get ir set from xhci itself
USB: Reset USB 3.0 devices on (re)discovery
xhci: Fix an error in count_sg_trbs_needed()
xhci: Fix errors in the running total calculations in the TRB math
xhci: Clarify some expressions in the TRB math
xhci: Avoid BUG() in interrupt context
|
|
* 'for-linus' of git://neil.brown.name/md:
md: Fix - again - partition detection when array becomes active
Fix over-zealous flush_disk when changing device size.
md: avoid spinlock problem in blk_throtl_exit
md: correctly handle probe of an 'mdp' device.
md: don't set_capacity before array is active.
md: Fix raid1->raid0 takeover
|
|
The variable 'val' is a 'unsigned int', so it can never be less than zero.
This fact makes the "val < 0" part of the test done in BUG_ON() in
mc13xxx_regulator_get_voltage() rather pointles since it can never have
any effect.
This patch removes the pointless test.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Fix unintended recursion in ironlake_disable_rc6
drm/i915: fix corruptions on i8xx due to relaxed fencing
drm/i915: skip FDI & PCH enabling for DP_A
agp/intel: Experiment with a 855GM GWB bit
drm/i915: don't enable FDI & transcoder interrupts after all
drm/i915: Ignore a hung GPU when flushing the framebuffer prior to a switch
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel into drm-fixes
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: Fix unintended recursion in ironlake_disable_rc6
|
|
MUSB is a non-standard host implementation which
can handle all speeds with the same core. We need
to set has_tt flag after commit
d199c96d41d80a567493e12b8e96ea056a1350c1 (USB: prevent
buggy hubs from crashing the USB stack) in order for
MUSB HCD to continue working.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Michael Jones <michael.jones@matrix-vision.de>
Tested-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
After disabling, we're meant to teardown the bo used for the contexts,
not recurse into ourselves again and preventing module unload.
Reported-and-tested-by: Ben Widawsky <bwidawsk@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Revert
b821eaa572fd737faaf6928ba046e571526c36c6
and
f3b99be19ded511a1bf05a148276239d9f13eefa
When I wrote the first of these I had a wrong idea about the
lifetime of 'struct block_device'. It can disappear at any time that
the block device is not open if it falls out of the inode cache.
So relying on the 'size' recorded with it to detect when the
device size has changed and so we need to revalidate, is wrong.
Rather, we really do need the 'changed' attribute stored directly in
the mddev and set/tested as appropriate.
Without this patch, a sequence of:
mknod / open / close / unlink
(which can cause a block_device to be created and then destroyed)
will result in a rescan of the partition table and consequence removal
and addition of partitions.
Several of these in a row can get udev racing to create and unlink and
other code can get confused.
With the patch, the rescan is only performed when needed and so there
are no races.
This is suitable for any stable kernel from 2.6.35.
Reported-by: "Wojcik, Krzysztof" <krzysztof.wojcik@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
|
|
There are two cases when we call flush_disk.
In one, the device has disappeared (check_disk_change) so any
data will hold becomes irrelevant.
In the oter, the device has changed size (check_disk_size_change)
so data we hold may be irrelevant.
In both cases it makes sense to discard any 'clean' buffers,
so they will be read back from the device if needed.
In the former case it makes sense to discard 'dirty' buffers
as there will never be anywhere safe to write the data. In the
second case it *does*not* make sense to discard dirty buffers
as that will lead to file system corruption when you simply enlarge
the containing devices.
flush_disk calls __invalidate_devices.
__invalidate_device calls both invalidate_inodes and invalidate_bdev.
invalidate_inodes *does* discard I_DIRTY inodes and this does lead
to fs corruption.
invalidate_bev *does*not* discard dirty pages, but I don't really care
about that at present.
So this patch adds a flag to __invalidate_device (calling it
__invalidate_device2) to indicate whether dirty buffers should be
killed, and this is passed to invalidate_inodes which can choose to
skip dirty inodes.
flusk_disk then passes true from check_disk_change and false from
check_disk_size_change.
dm avoids tripping over this problem by calling i_size_write directly
rathher than using check_disk_size_change.
md does use check_disk_size_change and so is affected.
This regression was introduced by commit 608aeef17a which causes
check_disk_size_change to call flush_disk, so it is suitable for any
kernel since 2.6.27.
Cc: stable@kernel.org
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Andrew Patterson <andrew.patterson@hp.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
This reverts commit 556ea928f78a390fe16ae584e6433dff304d3014.
Jeff Chua reports that it can cause some bluetooth devices (he mentions
an Bluetooth Intermec scanner) to just stop responding after a while
with messages like
[ 4533.361959] btusb 8-1:1.0: no reset_resume for driver btusb?
[ 4533.361964] btusb 8-1:1.1: no reset_resume for driver btusb?
from the kernel. See also
https://bugzilla.kernel.org/show_bug.cgi?id=26182
for other reports.
Reported-by: Jeff Chua <jeff.chua.linux@gmail.com>
Reported-by: Andrew Meakovski <meako@bigmir.net>
Reported-by: Jim Faulkner <jfaulkne@ccs.neu.edu>
Acked-by: Greg KH <gregkh@suse.de>
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Cc: stable@kernel.org (for 2.6.37)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel into drm-fixes
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ickle/drm-intel:
drm/i915: fix corruptions on i8xx due to relaxed fencing
drm/i915: skip FDI & PCH enabling for DP_A
agp/intel: Experiment with a 855GM GWB bit
drm/i915: don't enable FDI & transcoder interrupts after all
drm/i915: Ignore a hung GPU when flushing the framebuffer prior to a switch
|
|
It looks like gen2 has a peculiar interleaved 2-row inter-tile
layout. Probably inherited from i81x which had 2kb tiles (which
naturally fit an even-number-of-tile-rows scheme to fit onto 4kb
pages). There is no other mention of this in any docs (also not
in the Intel internal documention according to Chris Wilson).
Problem manifests itself in corruptions in the second half of the
last tile row (if the bo has an odd number of tiles). Which can
only happen with relaxed tiling (introduced in a00b10c360b35d6431a9).
So reject set_tiling calls that don't satisfy this constrain to
prevent broken userspace from causing havoc. While at it, also
check the size for newer chipsets.
LKML: https://lkml.org/lkml/2011/2/19/5
Reported-by: Indan Zupancic <indan@nul.nu>
Tested-by: Indan Zupancic <indan@nul.nu>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
Added support for usb ethernet (0x0fe6, 0x9700)
r8169: fix RTL8168DP power off issue.
r8169: correct settings of rtl8102e.
r8169: fix incorrect args to oob notify.
DM9000B: Fix PHY power for network down/up
DM9000B: Fix reg_save after spin_lock in dm9000_timeout
net_sched: long word align struct qdisc_skb_cb data
sfc: lower stack usage in efx_ethtool_self_test
bridge: Use IPv6 link-local address for multicast listener queries
bridge: Fix MLD queries' ethernet source address
bridge: Allow mcast snooping for transient link local addresses too
ipv6: Add IPv6 multicast address flag defines
bridge: Add missing ntohs()s for MLDv2 report parsing
bridge: Fix IPv6 multicast snooping by correcting offset in MLDv2 report
bridge: Fix IPv6 multicast snooping by storing correct protocol type
p54pci: update receive dma buffers before and after processing
fix cfg80211_wext_siwfreq lock ordering...
rt2x00: Fix WPA TKIP Michael MIC failures.
ath5k: Fix fast channel switching
tcp: undo_retrans counter fixes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
amd64-agp: fix crash at second module load
drm/radeon: fix regression with AA resolve checking
drm: drop commented out code and preceding comment
drm/vblank: Enable precise vblank timestamps for interlaced and doublescan modes.
drm/vblank: Use memory barriers optimized for atomic_t instead of generics.
drm/vblank: Use abs64(diff_ns) for s64 diff_ns instead of abs(diff_ns)
drm/radeon/kms: align height of fb allocation.
Revert "drm/radeon/kms: switch back to min->max pll post divider iteration"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/romieu/netdev-2.6
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: serio/gameport - use 'long' system workqueue
Input: synaptics - document 0x0c query
Input: tegra-kbc - add function keymap
|
|
The device is very similar to (0x0fe6, 0x8101),
And works well with dm9601 driver.
Signed-off-by: Shahar Havivi <shaharh@redhat.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- fix the RTL8111DP turn off the power when DASH is enabled.
- RTL_GIGA_MAC_VER_27 must wait for tx finish before reset.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
|
|
Adjust and remove certain settings of RTL8102E which are for previous chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-off-by: Francois Romieu <romieu@fr.zoreil.com>
|
|
It results in the wrong point address and influences RTL8168DP.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
|
|
DM9000 revision B needs 1 ms delay after PHY power-on.
PHY must be powered on by writing 0 into register DM9000_GPR before
all other settings will change (see Davicom spec and example code).
Remember, that register DM9000_GPR was not changed by reset sequence.
Without this fix the FIFO is out of sync and sends wrong data after
sequence of "ifconfig ethX down ; ifconfig ethX up".
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The spin_lock should hold before reading register.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 8ee294cd9def0004887da7f44b80563493b0a097 converted serio
subsystem event handling from using a dedicated thread to using
common workqueue. Unfortunately, this regressed our boot times,
due to the fact that serio jobs take long time to execute. While
the new concurrency managed workqueue code manages long-playing
works just fine and schedules additional workers as needed, such
works wreck havoc among remaining users of flush_scheduled_work().
To solve this problem let's move serio/gameport works from system_wq
to system_long_wq which nobody tries to flush.
Reported-and-tested-by: Hernando Torque <pantherchen@versanet.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Since Synaptics technical writers department is a bit slow releasing updated
Synaptics interface guide, let's add some new bits (with their blessing)
to the code so that they don't get lost.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The module forgot to sometimes unregister some resources.
This fixes Bug #22882.
[Patch updated to 2.6.38-rc3 by Randy Dunlap.]
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
* 'for-2639-rc4/i2c-fixes' of git://git.fluff.org/bjdooks/linux:
i2c-omap: fixup commit cb527ede1bf6ff2008a025606f25344b8ed7b4ac whitespace
i2c-omap: Double clear of ARDY status in IRQ handler
i2c-omap: fix build for !CONFIG_SUSPEND
i2c-omap: fix static suspend vs. runtime suspend
i2c-stu300: make sure adapter-name is terminated
|
|
Functions that are not used outsde of the module they are defined
should be marked as static.
Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
Revert "USB: Reset USB 3.0 devices on (re)discovery"
USB: musb: omap2430: fix kernel panic on reboot
sierra: add new ID for Airprime/Sierra USB IP modem
USB: serial/usb_wwan, fix tty NULL dereference
USB: Reset USB 3.0 devices on (re)discovery
USB: Add quirk for Samsung Android phone modem
USB: Add Samsung SGH-I500/Android modem ID switch to visor driver
USB: add quirks entry for Keytouch QWERTY Panel
usb: musb: omap2430: fix kernel panic on reboot
usb: musb: fix build breakage
|
|
Fixup the whitespace error noticed in cb527ede1bf6ff2008a025606f25344b8ed7b4ac
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
This errata occurs when the ARDY interrupt generation is enabled.
At the begining of every new transaction the ARDY interrupt is cleared.
On continuous i2c transactions where after clearing the ARDY bit from
I2C_STAT register (clearing the interrupt), the IRQ line is reasserted and the
I2C_STAT[ARDY] bit set again on 1. In fact, the ARDY status bit is not cleared
at the write access to I2C_STAT[ARDY] and only the IRQ line is deasserted and
then reasserted. This is not captured in the usual errata documents.
The workaround is to have a double clear of ARDY status in irq handler.
Signed-off-by: Richard woodruff <r-woodruff2@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
fix the build break when !CONFIG_SUSPEND
drivers/i2c/busses/i2c-omap.c:1173: error: lvalue required as unary '&' operand
make[3]: *** [drivers/i2c/busses/i2c-omap.o] Error 1
make[2]: *** [drivers/i2c/busses] Error 2
make[1]: *** [drivers/i2c] Error 2
make: *** [drivers] Error 2
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Some userspaces can emit a whole packet without disabling AA resolve
by the looks of it, so we have to deal with them.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Tested-by: Jorg Otte <jrg.otte@googlemail.com>
|
|
r100_gpu_init() was dropped in 90aca4d ("drm/radeon/kms: simplify &
improve GPU reset V2") but here it was only commented out.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
modes.
Testing showed the current code can already handle doublescan
video modes just fine. A trivial tweak makes it work for interlaced
scanout as well.
Tested and shown to be precise on Radeon rv530, r600 and
Intel 945-GME.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Documentation/atomic_ops.txt tells us that there are memory
barriers optimized for atomic_inc and other atomic_t ops.
Use these instead of smp_wmb(), and also to make the required
memory barriers around vblank counter increments more explicit.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Use of abs() wrongly wrapped diff_ns to 32 bit, which gives a 1/4000
probability of a missed vblank increment at each vblank irq reenable
if the kms driver doesn't support high precision vblank timestamping.
Not a big deal in practice, but let's make it nice.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
this aligns the height of the fb allocation so it doesn't trip
over the size checks later when we use this from userspace to
copy the buffer at X start.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This reverts commit a6f9761743bf35b052180f4a8bdae4d2cc0465f6.
Remove this commit as it is no longer necessary. The relevant bugs
were fixed properly in:
drm/radeon/kms: hopefully fix pll issues for real (v3)
5b40ddf888398ce4cccbf3b9d0a18d90149ed7ff
drm/radeon/kms: add missing frac fb div flag for dce4+
9f4283f49f0a96a64c5a45fe56f0f8c942885eef
This commit also broke certain ~5 Mhz modes on old arcade monitors,
so reverting this commit fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=29502
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
When runtime PM is enabled, each OMAP i2c device is suspended after
each i2c xfer. However, there are two cases when the static suspend
methods must be used to ensure the devices are suspended:
1) runtime PM is disabled, either at compile time or dynamically
via /sys/devices/.../power/control.
2) an i2c client driver uses i2c during it's suspend callback, thus
leaving the i2c driver active (NOTE: runtime suspend transitions are
disabled during system suspend, so i2c activity during system
suspend will runtime resume the device, but not runtime (re)suspend it.)
Since the actual work to suspend the device is handled by the
subsytem, call the bus methods to take care of it.
NOTE: This takes care of a known suspend problem on OMAP3 where the
TWL RTC driver does i2c xfers during its suspend path leaving the i2c
driver in an active state (since runtime suspend transistions are
disabled.)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Use strlcpy instead of strncpy.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
drivers/net/sfc/ethtool.c: In function ‘efx_ethtool_self_test’:
drivers/net/sfc/ethtool.c:613: warning: the frame size of 1200 bytes
is larger than 1024 bytes
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
