| Age | Commit message (Collapse) | Author |
|---|
|
bh->b_data is already a pointer to char so casts to 'char *' should
be meaningless. Remove them.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Fix mount-count check to emit warning only if s_max_mnt_count
is greater than 0 according to man tune2fs(8). Also removes
unnecessary casts.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
This fixes a WARN backtrace in mark_buffer_dirty() that occurs during unmount
when the underlying block device is removed. This bug has been seen on System
Z when removing all paths from a multipath-backed ext3 mount; on System P when
injecting enough PCI EEH errors to make the SCSI controller go offline; and
similar warnings have been seen (and patched) with ext2/ext4.
The super block update from a previous operation has marked the buffer as in
error, and the flag has to be cleared before doing the update. Similar changes
have been made to ext4 by commit 914258bf2cb22bf4336a1b1d90c551b4b11ca5aa.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
If a filesystem has inode size > 128 and someone deletes lost+found and
reuses inode 11 for some other file, extented attributes set for this
inode before umount will get lost after remounting the filesystem. This
is because extended attributes will get stored in an inode but ext3_iget
will ignore them due to workaround of a bug in an old mkfs.
Fix the problem by initializing i_extra_isize to 0 for freshly allocated
inodes where mkfs workaround in ext3_iget applies. This way these inodes
will always store extended attributes in a special block and no problems
occur.
The bug was spotted and a reproduction test provided by:
Masayoshi MIZUMA <m.mizuma@jp.fujitsu.com>
Reviewed-by: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (96 commits)
no need for list_for_each_entry_safe()/resetting with superblock list
Fix sget() race with failing mount
vfs: don't hold s_umount over close_bdev_exclusive() call
sysv: do not mark superblock dirty on remount
sysv: do not mark superblock dirty on mount
btrfs: remove junk sb_dirt change
BFS: clean up the superblock usage
AFFS: wait for sb synchronization when needed
AFFS: clean up dirty flag usage
cifs: truncate fallout
mbcache: fix shrinker function return value
mbcache: Remove unused features
add f_flags to struct statfs(64)
pass a struct path to vfs_statfs
update VFS documentation for method changes.
All filesystems that need invalidate_inode_buffers() are doing that explicitly
convert remaining ->clear_inode() to ->evict_inode()
Make ->drop_inode() just return whether inode needs to be dropped
fs/inode.c:clear_inode() is gone
fs/inode.c:evict() doesn't care about delete vs. non-delete paths now
...
Fix up trivial conflicts in fs/nilfs2/super.c
|
|
The mbcache code was written to support a variable number of indexes,
but all the existing users use exactly one index. Simplify to code to
support only that case.
There are also no users of the cache entry free operation, and none of
the users keep extra data in cache entries. Remove those features as
well.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Replace inode_setattr with opencoded variants of it in all callers. This
moves the remaining call to vmtruncate into the filesystem methods where it
can be replaced with the proper truncate sequence.
In a few cases it was obvious that we would never end up calling vmtruncate
so it was left out in the opencoded variant:
spufs: explicitly checks for ATTR_SIZE earlier
btrfs,hugetlbfs,logfs,dlmfs: explicitly clears ATTR_SIZE earlier
ufs: contains an opencoded simple_seattr + truncate that sets the filesize just above
In addition to that ncpfs called inode_setattr with handcrafted iattrs,
which allowed to trim down the opencoded variant.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Split up the block_write_begin implementation - __block_write_begin is a new
trivial wrapper for block_prepare_write that always takes an already
allocated page and can be either called from block_write_begin or filesystem
code that already has a page allocated. Remove the handling of already
allocated pages from block_write_begin after switching all callers that
do it to __block_write_begin.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Move the call to vmtruncate to get rid of accessive blocks to the callers
in prepearation of the new truncate calling sequence. This was only done
for DIO_LOCKING filesystems, so the __blockdev_direct_IO_newtrunc variant
was not needed anyway. Get rid of blockdev_direct_IO_no_locking and
its _newtrunc variant while at it as just opencoding the two additional
paramters is shorted than the name suffix.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
In data=journal mode, we still use block_write_begin() to prepare page for
writing. This function can occasionally mark buffer dirty which violates
journalling assumptions - when a buffer is part of a transaction, it should be
dirty and a buffer can be already part of a forget list of some transaction
when block_write_begin() gets called. This violation of journalling assumptions
then results in "JBD: Spotted dirty metadata buffer..." warnings.
In fact, temporary dirtying the buffer while the page is still locked does not
really cause problems to the journalling because we won't write the buffer
until the page gets unlocked. So we just have to make sure to clear dirty bits
before unlocking the page.
Reviewed-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
data=writeback mode is dangerous as it leads to higher data loss and stale data
exposure when systems crash. It should not be the default, especially when all
major distros ensure their ext3 filesystems default to ordered mode. Change the
default mode to the safer data=ordered mode, because we should be caring far
more about avoiding stale data exposure than performance.
CC: linux-ext4@vger.kernel.org
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Acked-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
It can happen that ext3_free_branches calls ext3_forget() for an indirect block
in an earlier transaction than a transaction in which we clear pointer to this
indirect block. Thus if we crash before a transaction clearing the block
pointer is committed, we will see indirect block pointing to already freed
blocks and complain during orphan list cleanup.
The fix is simple: Make sure ext3_forget() is called in the transaction
doing block pointer clearing.
This is a backport of an ext4 fix by Amir G. <amir73il@users.sourceforge.net>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
The nobh option was only supported for writeback mode, but given that all
write paths (except mmapped writed) actually create buffer heads, it
effectively was a no-op already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
[tytso@mit.edu: Fix compilation with CONFIG_JBD_DEBUG enabled]
Acked-by: tytso@mit.edu
cc: linux-ext4@vger.kernel.org
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
ext3 didn't update the ctime of the file when its permission was changed.
Steps to reproduce:
# touch aaa
# stat -c %Z aaa
1275289822
# setfacl -m 'u::x,g::x,o::x' aaa
# stat -c %Z aaa
1275289822 <- unchanged
But, according to the spec of the ctime, ext3 must update it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
quota: Convert quota statistics to generic percpu_counter
ext3 uses rb_node = NULL; to zero rb_root.
quota: Fixup dquot_transfer
reiserfs: Fix resuming of quotas on remount read-write
pohmelfs: Remove dead quota code
ufs: Remove dead quota code
udf: Remove dead quota code
quota: rename default quotactl methods to dquot_
quota: explicitly set ->dq_op and ->s_qcop
quota: drop remount argument to ->quota_on and ->quota_off
quota: move unmount handling into the filesystem
quota: kill the vfs_dq_off and vfs_dq_quota_on_remount wrappers
quota: move remount handling into the filesystem
ocfs2: Fix use after free on remount read-only
Fix up conflicts in fs/ext4/super.c and fs/ufs/file.c
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The problem with this is that 17d9ddc72fb8bba0d4f678 ("rbtree: Add support
for augmented rbtrees") in the linux-next tree adds a new field to that
struct which needs to be NULLas well. This patch uses RB_ROOT as the
intializer so all of the relevant fields will be NULL'd.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Follow the dquot_* style used elsewhere in dquot.c.
[Jan Kara: Fixed up missing conversion of ext2]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Remount handling has fully moved into the filesystem, so all this is
superflous now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Currently the VFS calls into the quotactl interface for unmounting
filesystems. This means filesystems with their own quota handling
can't easily distinguish between user-space originating quotaoff
and an unount. Instead move the responsibily of the unmount handling
into the filesystem to be consistent with all other dquot handling.
Note that we do call dquot_disable a lot later now, e.g. after
a sync_filesystem. But this is fine as the quota code does all its
writes via blockdev's mapping and that is synced even later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Instead of having wrappers in the VFS namespace export the dquot_suspend
and dquot_resume helpers directly. Also rename vfs_quota_disable to
dquot_disable while we're at it.
[Jan Kara: Moved dquot_suspend to quotaops.h and made it inline]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Currently do_remount_sb calls into the dquot code to tell it about going
from rw to ro and ro to rw. Move this code into the filesystem to
not depend on the dquot code in the VFS - note ocfs2 already ignores
these calls and handles remount by itself. This gets rid of overloading
the quotactl calls and allows to unify the VFS and XFS codepaths in
that area later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (69 commits)
fix handling of offsets in cris eeprom.c, get rid of fake on-stack files
get rid of home-grown mutex in cris eeprom.c
switch ecryptfs_write() to struct inode *, kill on-stack fake files
switch ecryptfs_get_locked_page() to struct inode *
simplify access to ecryptfs inodes in ->readpage() and friends
AFS: Don't put struct file on the stack
Ban ecryptfs over ecryptfs
logfs: replace inode uid,gid,mode initialization with helper function
ufs: replace inode uid,gid,mode initialization with helper function
udf: replace inode uid,gid,mode init with helper
ubifs: replace inode uid,gid,mode initialization with helper function
sysv: replace inode uid,gid,mode initialization with helper function
reiserfs: replace inode uid,gid,mode initialization with helper function
ramfs: replace inode uid,gid,mode initialization with helper function
omfs: replace inode uid,gid,mode initialization with helper function
bfs: replace inode uid,gid,mode initialization with helper function
ocfs2: replace inode uid,gid,mode initialization with helper function
nilfs2: replace inode uid,gid,mode initialization with helper function
minix: replace inode uid,gid,mode init with helper
ext4: replace inode uid,gid,mode init with helper
...
Trivial conflict in fs/fs-writeback.c (mark bitfields unsigned)
|
|
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Conflicts:
fs/ext3/fsync.c
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Quota must being initialized if size or uid/git changes requested.
But initialization performed in two different places:
in case of i_size file system is responsible for dquot init
, but in case of uid/gid init will be called internally in
dquot_transfer().
This ambiguity makes code harder to understand.
Let's move this logic to one common helper function.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
ext4 was updated to accept barrier/nobarrier mount options
in addition to the older barrier=0/1. The barrier story
is complex enough, we should help people by making the options
the same at least, even if the defaults are different.
This patch allows the barrier/nobarrier mount options for ext3,
while keeping nobarrier the default.
It also unconditionally displays barrier status in show_options,
and prints a message at mount time if barriers are not enabled,
just as ext4 does.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
log_start_commit() returns 1 only when it started a transaction
commit. Thus in case transaction commit is already running, we
fail to wait for the commit to finish. Fix the issue by always
waiting for the commit regardless of the log_start_commit return
value.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Currently block/inode/dir counters are initialized before journal was
recovered. In fact after journal recovery this info will probably
change which results in incorrect numbers returned from statfs(2).
BUG:#15768
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
There is no point in loading bitmap for groups which are completely full.
This causes noticeable performance problems (and memory pressure) on small
systems with large full filesystem
(http://marc.info/?l=linux-ext4&m=126843108314310&w=2).
Jan Kara: Added a comment and changed check to use cpu-endian value.
Signed-off-by: "Frans van de Wiel" <fvdw@fvdw.eu>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
The patch just convert all blkdev_issue_xxx function to common
set of flags. Wait/allocation semantics preserved.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
generic setattr implementation is no longer responsible for
quota transfer so synlinks must be handled via ext3_setattr.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
In commit 9df93939b735 ("ext3: Use bitops to read/modify
EXT3_I(inode)->i_state") ext3 changed its internal 'i_state' variable to
use bitops for its state handling. However, unline the same ext4
change, it didn't actually change the name of the field when it changed
the semantics of it.
As a result, an old use of 'i_state' remained in fs/ext3/ialloc.c that
initialized the field to EXT3_STATE_NEW. And that does not work
_at_all_ when we're now working with individually named bits rather than
values that get masked. So the code tried to mark the state to be new,
but in actual fact set the field to EXT3_STATE_JDATA. Which makes no
sense at all, and screws up all the code that checks whether the inode
was newly allocated.
In particular, it made the xattr code unhappy, and caused various random
behavior, like apparently
https://bugzilla.redhat.com/show_bug.cgi?id=577911
So fix the initialization, and rename the field to match ext4 so that we
don't have this happen again.
Cc: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Daniel J Walsh <dwalsh@redhat.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Conflicts:
Documentation/filesystems/proc.txt
arch/arm/mach-u300/include/mach/debug-macro.S
drivers/net/qlge/qlge_ethtool.c
drivers/net/qlge/qlge_main.c
drivers/net/typhoon.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6: (33 commits)
quota: stop using QUOTA_OK / NO_QUOTA
dquot: cleanup dquot initialize routine
dquot: move dquot initialization responsibility into the filesystem
dquot: cleanup dquot drop routine
dquot: move dquot drop responsibility into the filesystem
dquot: cleanup dquot transfer routine
dquot: move dquot transfer responsibility into the filesystem
dquot: cleanup inode allocation / freeing routines
dquot: cleanup space allocation / freeing routines
ext3: add writepage sanity checks
ext3: Truncate allocated blocks if direct IO write fails to update i_size
quota: Properly invalidate caches even for filesystems with blocksize < pagesize
quota: generalize quota transfer interface
quota: sb_quota state flags cleanup
jbd: Delay discarding buffers in journal_unmap_buffer
ext3: quota_write cross block boundary behaviour
quota: drop permission checks from xfs_fs_set_xstate/xfs_fs_set_xquota
quota: split out compat_sys_quotactl support from quota.c
quota: split out netlink notification support from quota.c
quota: remove invalid optimization from quota_sync_all
...
Fixed trivial conflicts in fs/namei.c and fs/ufs/inode.c
|
|
This gives the filesystem more information about the writeback that
is happening. Trond requested this for the NFS unstable write handling,
and other filesystems might benefit from this too by beeing able to
distinguish between the different callers in more detail.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Get rid of the initialize dquot operation - it is now always called from
the filesystem and if a filesystem really needs it's own (which none
currently does) it can just call into it's own routine directly.
Rename the now static low-level dquot_initialize helper to __dquot_initialize
and vfs_dq_init to dquot_initialize to have a consistent namespace.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Currently various places in the VFS call vfs_dq_init directly. This means
we tie the quota code into the VFS. Get rid of that and make the
filesystem responsible for the initialization. For most metadata operations
this is a straight forward move into the methods, but for truncate and
open it's a bit more complicated.
For truncate we currently only call vfs_dq_init for the sys_truncate case
because open already takes care of it for ftruncate and open(O_TRUNC) - the
new code causes an additional vfs_dq_init for those which is harmless.
For open the initialization is moved from do_filp_open into the open method,
which means it happens slightly earlier now, and only for regular files.
The latter is fine because we don't need to initialize it for operations
on special files, and we already do it as part of the namespace operations
for directories.
Add a dquot_file_open helper that filesystems that support generic quotas
can use to fill in ->open.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Get rid of the drop dquot operation - it is now always called from
the filesystem and if a filesystem really needs it's own (which none
currently does) it can just call into it's own routine directly.
Rename the now static low-level dquot_drop helper to __dquot_drop
and vfs_dq_drop to dquot_drop to have a consistent namespace.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Currently clear_inode calls vfs_dq_drop directly. This means
we tie the quota code into the VFS. Get rid of that and make the
filesystem responsible for the drop inside the ->clear_inode
superblock operation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Get rid of the transfer dquot operation - it is now always called from
the filesystem and if a filesystem really needs it's own (which none
currently does) it can just call into it's own routine directly.
Rename the now static low-level dquot_transfer helper to __dquot_transfer
and vfs_dq_transfer to dquot_transfer to have a consistent namespace,
and make the new dquot_transfer return a normal negative errno value
which all callers expect.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Get rid of the alloc_inode and free_inode dquot operations - they are
always called from the filesystem and if a filesystem really needs
their own (which none currently does) it can just call into it's
own routine directly.
Also get rid of the vfs_dq_alloc/vfs_dq_free wrappers and always
call the lowlevel dquot_alloc_inode / dqout_free_inode routines
directly, which now lose the number argument which is always 1.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Get rid of the alloc_space, free_space, reserve_space, claim_space and
release_rsv dquot operations - they are always called from the filesystem
and if a filesystem really needs their own (which none currently does)
it can just call into it's own routine directly.
Move shared logic into the common __dquot_alloc_space,
dquot_claim_space_nodirty and __dquot_free_space low-level methods,
and rationalize the wrappers around it to move as much as possible
code into the common block for CONFIG_QUOTA vs not. Also rename
all these helpers to be named dquot_* instead of vfs_dq_*.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
- There is theoretical possibility to perform writepage on
RO superblock. Add explicit check for what case.
- Page must being locked before writepage.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
We have to truncate blocks allocated to file during direct IO when we
fail to update i_size properly.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
We always assume what dquot update result in changes in one data block
But ext3_quota_write() function may handle cross block boundary writes
In fact if this ever happen it will result in incorrect journal credits
reservation. And later bug_on triggering. As soon this never happen the
boundary cross loop is NOOP. In order to make things straight
let's remove this loop and assert cross boundary condition.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Jan Kara <jack@suse.cz>
|
