| Age | Commit message (Collapse) | Author |
|---|
|
In case we detect a problem and bail out, we fail to set "ret" to a
nonzero value, and udf_load_logicalvol will mistakenly report success.
Signed-off-by: Nikola Pajkovsky <npajkovs@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
If s_lvid_bh is not freed and set to NULL before re-scanning partition
with default block size, we might end up using wrong lvid in case
s_lvid_bh is not updated in udf_load_logicalvolint during rescan.
Signed-off-by: Ashish Sangwan <ashish.sangwan2@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
When a partition table length is corrupted to be close to 1 << 32, the
check for its length may overflow on 32-bit systems and we will think
the length is valid. Later on the kernel can crash trying to read beyond
end of buffer. Fix the check to avoid possible overflow.
CC: stable@vger.kernel.org
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
When we are mounting filesystem, we can load one partition table before
finding out that we cannot complete processing of logical volume descriptor
and trying the reserve descriptor. Free the table properly before trying
the reserve descriptor.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
The UDF file-system does not need the 's_dirt' superblock flag because it does
not define the 'write_super()' method. This flag was set to 1 in few places and
set to 0 in '->sync_fs()' and was basically useless. Stop using it because it
is on its way out.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Add sanity checks when loading sparing table from disk to avoid accessing
unallocated memory or writing to it.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Check provided length of partition table so that (possibly maliciously)
corrupted partition table cannot cause accessing data beyond current buffer.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull ext3, UDF, and quota fixes from Jan Kara:
"A couple of ext3 & UDF fixes and also one improvement in quota
locking."
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext3: fix start and len arguments handling in ext3_trim_fs()
udf: Fix deadlock in udf_release_file()
udf: Fix file entry logicalBlocksRecorded
udf: Fix handling of i_blocks
quota: Make quota code not call tty layer with dqptr_sem held
udf: Init/maintain file entry checkpoint field
ext3: Update ctime in ext3_splice_branch() only when needed
ext3: Don't call dquot_free_block() if we don't update anything
udf: Remove unnecessary OOM messages
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
New field of struct super_block - ->s_max_links. Maximal allowed
value of ->i_nlink or 0; in the latter case all checks still need
to be done in ->link/->mkdir/->rename instances. Note that this
limit applies both to directoris and to non-directories.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Per call site OOM messages are unnecessary.
k.alloc and v.alloc failures use dump_stack().
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext2/3/4: delete unneeded includes of module.h
ext{3,4}: Fix potential race when setversion ioctl updates inode
udf: Mark LVID buffer as uptodate before marking it dirty
ext3: Don't warn from writepage when readonly inode is spotted after error
jbd: Remove j_barrier mutex
reiserfs: Force inode evictions before umount to avoid crash
reiserfs: Fix quota mount option parsing
udf: Treat symlink component of type 2 as /
udf: Fix deadlock when converting file from in-ICB one to normal one
udf: Cleanup calling convention of inode_getblk()
ext2: Fix error handling on inode bitmap corruption
ext3: Fix error handling on inode bitmap corruption
ext3: replace ll_rw_block with other functions
ext3: NULL dereference in ext3_evict_inode()
jbd: clear revoked flag on buffers before a new transaction started
ext3: call ext3_mark_recovery_complete() when recovery is really needed
|
|
When we hit EIO while writing LVID, the buffer uptodate bit is cleared.
This then results in an anoying warning from mark_buffer_dirty() when we
write the buffer again. So just set uptodate flag unconditionally.
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
note re mount options: fmask and dmask are explicitly truncated to 12bit,
UDF_INVALID_MODE just needs to be guaranteed to differ from any such value.
And umask is used only in &= with umode_t, so we ignore other bits anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Seeing that just about every destructor got that INIT_LIST_HEAD() copied into
it, there is no point whatsoever keeping this INIT_LIST_HEAD in inode_init_once();
the cost of taking it into inode_init_always() will be negligible for pipes
and sockets and negative for everything else. Not to mention the removal of
boilerplate code from ->destroy_inode() instances...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Use simple ->s_flags variable instead of u8 variable for each flag.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
It is not necessary to load mirror metadata FE when metadata FE is OK. So try
to read it only the first time udf_get_pblock_meta25() fails to map the block
from metadata FE.
Signed-off-by: Ashish Sangwan <ashishsangwan2@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Just whitespace and argument alignment.
Introduce some checkpatch warnings that deserve to be ignored.
Reviewed-by: NamJae Jeon <linkinjeon@gmail.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Use %pV and remove a static buffer to save some text space and fix possible
issues when several processes call error reporting function in parallel. Also
change error level from KERN_CRIT to KERN_ERR.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Use the current logging styles.
Convert a few printks that should have been udf_warn and udf_err.
Coalesce formats. Add #define pr_fmt.
Move an #include "udfdecls.h" above other includes in udftime.c
so pr_fmt works correctly. Strip prefixes from conversions as appropriate.
Reorder logging definitions in udfdecl.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Rename udf_warning to udf_warn for consistency with normal logging
uses of pr_warn.
Rename function udf_warning to _udf_warn.
Remove __func__ from uses and move __func__ to a new udf_warn
macro that calls _udf_warn.
Add \n's to uses of udf_warn, remove \n from _udf_warn.
Coalesce formats.
Reviewed-by: NamJae Jeon <linkinjeon@gmail.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Rename udf_error to udf_err for consistency with normal logging
uses of pr_err.
Rename function udf_err to _udf_err.
Remove __func__ from uses and move __func__ to a new udf_err
macro that calls _udf_err.
Some of the udf_error uses had \n terminations, some did not so
standardize \n's to udf_err uses, remove \n from _udf_err function.
Coalesce udf_err formats.
One message prefixed with udf_read_super is now prefixed with
udf_fill_super.
Reviewed-by: NamJae Jeon <linkinjeon@gmail.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
If there is a problem with a scratched disc or loader, it's valuable to know
which error occurred.
Convert some debug messages to udf_error, neaten those messages too.
Add the calculated tag checksum and the read checksum to error message.
Make udf_error a public function and move the logging prototypes together.
Original-patch-by: NamJae Jeon <linkinjeon@gmail.com>
Reviewed-by: NamJae Jeon <linkinjeon@gmail.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6:
UDF: Close small mem leak in udf_find_entry()
udf: Fix directory corruption after extent merging
udf: Protect udf_file_aio_write from possible races
udf: Remove unnecessary bkl usages
udf: Use of s_alloc_mutex to serialize udf_relocate_blocks() execution
udf: Replace bkl with the UDF_I(inode)->i_data_sem for protect udf_inode_info struct
udf: Remove BKL from free space counting functions
udf: Call udf_add_free_space() for more blocks at once in udf_free_blocks()
udf: Remove BKL from udf_put_super() and udf_remount_fs()
udf: Protect default inode credentials by rwlock
udf: Protect all modifications of LVID with s_alloc_mutex
udf: Move handling of uniqueID into a helper function and protect it by a s_alloc_mutex
udf: Remove BKL from udf_update_inode
udf: Convert UDF_SB(sb)->s_flags to use bitops
fs/udf: Add printf format/argument verification
fs/udf: Use vzalloc
(Evil merge: this also removes the BKL dependency from the Kconfig file)
|
|
RCU free the struct inode. This will allow:
- Subsequent store-free path walking patch. The inode must be consulted for
permissions when walking, so an RCU inode reference is a must.
- sb_inode_list_lock to be moved inside i_lock because sb list walkers who want
to take i_lock no longer need to take sb_inode_list_lock to walk the list in
the first place. This will simplify and optimize locking.
- Could remove some nested trylock loops in dcache code
- Could potentially simplify things a bit in VM land. Do not need to take the
page lock to follow page->mapping.
The downsides of this is the performance cost of using RCU. In a simple
creat/unlink microbenchmark, performance drops by about 10% due to inability to
reuse cache-hot slab objects. As iterations increase and RCU freeing starts
kicking over, this increases to about 20%.
In cases where inode lifetimes are longer (ie. many inodes may be allocated
during the average life span of a single inode), a lot of this cache reuse is
not applicable, so the regression caused by this patch is smaller.
The cache-hot regression could largely be avoided by using SLAB_DESTROY_BY_RCU,
however this adds some complexity to list walking and store-free path walking,
so I prefer to implement this at a later date, if it is shown to be a win in
real situations. I haven't found a regression in any non-micro benchmark so I
doubt it will be a problem.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
|
|
The udf_readdir(), udf_lookup(), udf_create(), udf_mknod(), udf_mkdir(),
udf_rmdir(), udf_link(), udf_get_parent() and udf_unlink() seems already
adequately protected by i_mutex held by VFS invoking calls. The udf_rename()
instead should be already protected by lock_rename again by VFS. The
udf_ioctl(), udf_fill_super() and udf_evict_inode() don't requires any further
protection.
This work was supported by a hardware donation from the CE Linux Forum.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
udf_inode_info struct
Replace bkl with the UDF_I(inode)->i_data_sem rw semaphore in
udf_release_file(), udf_symlink(), udf_symlink_filler(), udf_get_block(),
udf_block_map(), and udf_setattr(). The rule now is that any operation
on regular file's or symlink's extents (or generally allocation information
including goal block) needs to hold i_data_sem.
This work was supported by a hardware donation from the CE Linux Forum.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
udf_count_free_bitmap() does not need BKL because bitmaps are in a fixed
place on disk and so we can count set bits without serialization.
udf_count_free_table() is now protected by s_alloc_mutex instead of BKL
to get a consistent view of free space extents.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
udf_put_super() does not need BKL because the filesystem is shut down so
there's nothing to race with. The credential changes in udf_remount_fs()
and LVID changes are now protected by dedicated locks so we can remove BKL
from this function as well.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Superblock carries credentials (uid, gid, etc.) which are used as default
values in __udf_read_inode() when media does not provide these. These
credentials can change during remount so we protect them by a rwlock so that
each inode gets a consistent set of credentials.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
udf_open_lvid() and udf_close_lvid() were modifying LVID without
s_alloc_mutex. Since they can be called from remount, the modification
could race with other filesystem modifications of LVID so protect them
by s_alloc_mutex just to be sure.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
s_alloc_mutex
uniqueID handling has been duplicated in three places. Move it into a common
helper. Since we modify an LVID buffer with uniqueID update, we take
sbi->s_alloc_mutex to protect agaist other modifications of the structure.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
... and switch of the obvious get_sb_bdev() users to ->mount()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
This patch is a preparation necessary to remove the BKL from do_new_mount().
It explicitly adds calls to lock_kernel()/unlock_kernel() around
get_sb/fill_super operations for filesystems that still uses the BKL.
I've read through all the code formerly covered by the BKL inside
do_kern_mount() and have satisfied myself that it doesn't need the BKL
any more.
do_kern_mount() is already called without the BKL when mounting the rootfs
and in nfsctl. do_kern_mount() calls vfs_kern_mount(), which is called
from various places without BKL: simple_pin_fs(), nfs_do_clone_mount()
through nfs_follow_mountpoint(), afs_mntpt_do_automount() through
afs_mntpt_follow_link(). Both later functions are actually the filesystems
follow_link inode operation. vfs_kern_mount() is calling the specified
get_sb function and lets the filesystem do its job by calling the given
fill_super function.
Therefore I think it is safe to push down the BKL from the VFS to the
low-level filesystems get_sb/fill_super operation.
[arnd: do not add the BKL to those file systems that already
don't use it elsewhere]
Signed-off-by: Jan Blunck <jblunck@infradead.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Christoph Hellwig <hch@infradead.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (96 commits)
no need for list_for_each_entry_safe()/resetting with superblock list
Fix sget() race with failing mount
vfs: don't hold s_umount over close_bdev_exclusive() call
sysv: do not mark superblock dirty on remount
sysv: do not mark superblock dirty on mount
btrfs: remove junk sb_dirt change
BFS: clean up the superblock usage
AFFS: wait for sb synchronization when needed
AFFS: clean up dirty flag usage
cifs: truncate fallout
mbcache: fix shrinker function return value
mbcache: Remove unused features
add f_flags to struct statfs(64)
pass a struct path to vfs_statfs
update VFS documentation for method changes.
All filesystems that need invalidate_inode_buffers() are doing that explicitly
convert remaining ->clear_inode() to ->evict_inode()
Make ->drop_inode() just return whether inode needs to be dropped
fs/inode.c:clear_inode() is gone
fs/inode.c:evict() doesn't care about delete vs. non-delete paths now
...
Fix up trivial conflicts in fs/nilfs2/super.c
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
This fixes this warning when building the kernel:
CC fs/udf/super.o
fs/udf/super.c: In function 'udf_load_sequence':
fs/udf/super.c:1582:22: warning: variable 'sbi' set but not used
Please have a look, when you have time and let me know.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Quota on UDF is non-functional at least since 2.6.16 (I'm too lazy to
do more archeology) because it does not provide .quota_write and .quota_read
functions and thus quotaon(8) just returns EINVAL. Since nobody complained
for all those years and quota support is not even in UDF standard just nuke
it.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Follow the dquot_* style used elsewhere in dquot.c.
[Jan Kara: Fixed up missing conversion of ext2]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Only set the quota operation vectors if the filesystem actually supports
quota instead of doing it for all filesystems in alloc_super().
[Jan Kara: Export dquot_operations and vfs_quotactl_ops]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Currently the VFS calls into the quotactl interface for unmounting
filesystems. This means filesystems with their own quota handling
can't easily distinguish between user-space originating quotaoff
and an unount. Instead move the responsibily of the unmount handling
into the filesystem to be consistent with all other dquot handling.
Note that we do call dquot_disable a lot later now, e.g. after
a sync_filesystem. But this is fine as the quota code does all its
writes via blockdev's mapping and that is synced even later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Instead of having wrappers in the VFS namespace export the dquot_suspend
and dquot_resume helpers directly. Also rename vfs_quota_disable to
dquot_disable while we're at it.
[Jan Kara: Moved dquot_suspend to quotaops.h and made it inline]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Currently do_remount_sb calls into the dquot code to tell it about going
from rw to ro and ro to rw. Move this code into the filesystem to
not depend on the dquot code in the VFS - note ocfs2 already ignores
these calls and handles remount by itself. This gets rid of overloading
the quotactl calls and allows to unify the VFS and XFS codepaths in
that area later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
Some disks do not contain VAT inode in the last recorded block as required
by the standard but a few blocks earlier (or the number of recorded blocks
is wrong). So look for the VAT inode a bit before the end of the media.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
blocks
VAT inode is located in the last block recorded block of the medium. When the
drive errorneously reports number of recorded blocks, we failed to load the VAT
inode and thus mount the medium. This patch makes kernel try to read VAT inode
from the last block of the device if it is different from the last recorded
block.
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
[xfs, btrfs, capifs, shmem don't need BKL, exempt]
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Move BKL into ->put_super from the only caller. A couple of
filesystems had trivial enough ->put_super (only kfree and NULLing of
s_fs_info + stuff in there) to not get any locking: coda, cramfs, efs,
hugetlbfs, omfs, qnx4, shmem, all others got the full treatment. Most
of them probably don't need it, but I'd rather sort that out individually.
Preferably after all the other BKL pushdowns in that area.
[AV: original used to move lock_super() down as well; these changes are
removed since we don't do lock_super() at all in generic_shutdown_super()
now]
[AV: fuse, btrfs and xfs are known to need no damn BKL, exempt]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
