| Age | Commit message (Collapse) | Author |
|---|
|
Checking if an address is a vmalloc address is done in a couple of places.
Define a common version in mm.h and replace the other checks.
Again the include structures suck. The definition of VMALLOC_START and
VMALLOC_END is not available in vmalloc.h since highmem.c cannot be included
there.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Simplify page cache zeroing of segments of pages through 3 functions
zero_user_segments(page, start1, end1, start2, end2)
Zeros two segments of the page. It takes the position where to
start and end the zeroing which avoids length calculations and
makes code clearer.
zero_user_segment(page, start, end)
Same for a single segment.
zero_user(page, start, length)
Length variant for the case where we know the length.
We remove the zero_user_page macro. Issues:
1. Its a macro. Inline functions are preferable.
2. The KM_USER0 macro is only defined for HIGHMEM.
Having to treat this special case everywhere makes the
code needlessly complex. The parameter for zeroing is always
KM_USER0 except in one single case that we open code.
Avoiding KM_USER0 makes a lot of code not having to be dealing
with the special casing for HIGHMEM anymore. Dealing with
kmap is only necessary for HIGHMEM configurations. In those
configurations we use KM_USER0 like we do for a series of other
functions defined in highmem.h.
Since KM_USER0 is depends on HIGHMEM the existing zero_user_page
function could not be a macro. zero_user_* functions introduced
here can be be inline because that constant is not used when these
functions are called.
Also extract the flushing of the caches to be outside of the kmap.
[akpm@linux-foundation.org: fix nfs and ntfs build]
[akpm@linux-foundation.org: fix ntfs build some more]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: <linux-ext4@vger.kernel.org>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: David Chinner <dgc@sgi.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch should fix the issue seen on Alpha with unaligned accesses in
the new readdir code. By aligning each dirent to sizeof(u64) we'll avoid
unaligned accesses. To make doubly sure we're not hitting problems also
rearrange struct hack_dirent to avoid holes.
SGI-PV: 975411
SGI-Modid: xfs-linux-melb:xfs-kern:30302a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
After reading the directory contents into the temporary buffer, we grab
each dirent and pass it to filldir witht eh current offset of the dirent.
The current offset was not being set for the first dirent in the temporary
buffer, which coul dresult in bad offsets being set in the f_pos field
result in looping and duplicate entries being returned from readdir.
SGI-PV: 974905
SGI-Modid: xfs-linux-melb:xfs-kern:30282a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
This was broken by my '[XFS] simplify xfs_create/mknod/symlink prototype',
which assigned the re-shuffled ondisk dev_t back to the rdev variable in
xfs_vn_mknod. Because of that i_rdev is set to the ondisk dev_t instead of
the linux dev_t later down the function.
Fortunately the fix for it is trivial: we can just remove the assignment
because xfs_revalidate_inode has done the proper job before unlocking the
inode.
SGI-PV: 974873
SGI-Modid: xfs-linux-melb:xfs-kern:30273a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
The recent filldir regression fix was not putting the correct d_off in
each dirent. This was resulting in incorrect cookies being passed to dmapi
ioctls and the wrong offset appearing in the dirents. readdir was
unaffected as the filp->f_pos was being updated with the correct offset
and this was being written into the last dirent in each buffer. Fix the
XFS code to do the right thing.
SGI-PV: 973746
SGI-Modid: xfs-linux-melb:xfs-kern:30240a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
On last close of a file we purge blocks beyond eof. The same code is used
when we truncate the file size down. In this case we need to wait for any
pending I/Os for dirty pages beyond the new eof. For the last close case
we are not changing the file size and therefore do not need to wait for
any I/Os to complete. This fixes a performance bottleneck where writes
into the page cache and cache flushes can become mutually exclusive.
SGI-PV: 964002
SGI-Modid: xfs-linux-melb:xfs-kern:30220a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Peter Leckie <pleckie@sgi.com>
|
|
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
[XFS] Fix xfs_ichgtime()s broken usage of I_SYNC
[XFS] Make xfsbufd threads freezable
[XFS] revert to double-buffering readdir
[XFS] Fix broken inode cluster setup.
[XFS] Clear XBF_READ_AHEAD flag on I/O completion.
[XFS] Fixed a few bugs in xfs_buf_associate_memory()
[XFS] 971064 Various fixups for xfs_bulkstat().
[XFS] Fix dbflush panic in xfs_qm_sync.
|
|
The recent I_LOCK->I_SYNC changes mistakenly changed xfs_ichgtime to look
at I_SYNC instead of I_LOCK. This was incorrect and prevents newly created
inodes from moving to the dirty list. Change this to the correct check
which is for I_NEW, not I_LOCK or I_SYNC so that behaviour is correct.
SGI-PV: 974225
SGI-Modid: xfs-linux-melb:xfs-kern:30204a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
Fix breakage caused by commit 831441862956fffa17b9801db37e6ea1650b0f69
that did not introduce the necessary call to set_freezable() in
xfs/linux-2.6/xfs_buf.c .
SGI-PV: 974224
SGI-Modid: xfs-linux-melb:xfs-kern:30203a
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
The current readdir implementation deadlocks on a btree buffers locks
because nfsd calls back into ->lookup from the filldir callback. The only
short-term fix for this is to revert to the old inefficient
double-buffering scheme.
SGI-PV: 973377
SGI-Modid: xfs-linux-melb:xfs-kern:30201a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
The radix tree based inode caches did away with the inode cluster hashes,
replacing them with a bunch of masking and gang lookups on the radix tree.
This masking got broken when moving the code to per-ag radix trees and
indexing by agino # rather than straight inode number. The result is
clustered inode writeback does not cluster and things can go extremely
slowly when there are lots of inodes to write.
Fix it up by comparing the agino # of the inode we just looked up to the
index of the cluster we are looking for.
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
SGI-PV: 972915
SGI-Modid: xfs-linux-melb:xfs-kern:30033a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
SGI-PV: 972554
SGI-Modid: xfs-linux-melb:xfs-kern:30128a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
|
|
- calculation of 'page_count' was incorrect as it did not
consider the offset of 'mem' into the first page. The
logic to bump 'page_count' didn't work if 'len' was <=
PAGE_CACHE_SIZE (ie offset = 3k, len = 2k).
- setting b_buffer_length to 'len' is incorrect if 'offset'
is > 0. Set it to the total length of the buffer.
- I suspect that passing a non-aligned address into
mem_to_page() for the first page may have been causing
issues - don't know but just tidy up that code anyway.
SGI-PV: 971596
SGI-Modid: xfs-linux-melb:xfs-kern:30143a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
|
|
- sanity check for NULL user buffer in xfs_ioc_bulkstat[_compat]()
- remove the special case for XFS_IOC_FSBULKSTAT with count == 1. This
special case causes bulkstat to fail because the special case uses
xfs_bulkstat_single() instead of xfs_bulkstat() and the two functions
have different semantics. xfs_bulkstat() will return the next inode
after the one supplied while skipping internal inodes (ie quota inodes).
xfs_bulkstate_single() will only lookup the inode supplied and return
an error if it is an internal inode.
- in xfs_bulkstat(), need to initialise 'lastino' to the inode supplied
so in cases were we return without examining any inodes the scan wont
restart back at zero.
- sanity check for valid *ubcountp values. Cannot sanity check for valid
ubuffer here because some users of xfs_bulkstat() don't supply a buffer.
- checks against 'ubleft' (the space left in the user's buffer) should be
against 'statstruct_size' which is the supplied minimum object size.
The mixture of checks against statstruct_size and 0 was one of the
reasons we were skipping inodes.
- if the formatter function returns BULKSTAT_RV_NOTHING and an error and
the error is not ENOENT or EINVAL then we need to abort the scan. ENOENT
is for inodes that are no longer valid and we just skip them. EINVAL is
returned if we try to lookup an internal inode so we skip them too. For
a DMF scan if the inode and DMF attribute cannot fit into the space left
in the user's buffer it would return ERANGE. We didn't handle this error
and skipped the inode. We would continue to skip inodes until one fitted
into the user's buffer or we completed the scan.
- put back the recalculation of agino (that got removed with the last fix)
at the end of the while loop. This is because the code at the start of
the loop expects agino to be the last inode examined if it is non-zero.
- if we found some inodes but then encountered an error, return success
this time and the error next time. If the formatter aborted with ENOMEM
we will now return this error but only if we couldn't read any inodes.
Previously if we encountered ENOMEM without reading any inodes we
returned a zero count and no error which falsely indicated the scan was
complete.
SGI-PV: 973431
SGI-Modid: xfs-linux-melb:xfs-kern:30089a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
|
|
The recent behaviour layer removal dropped the check for quotas that have
been requested at mount time but have subsequently been turned off. This
results in a panic when accessing m_quotainfo which has been freed.
This patch adds the check originally made by xfs_qm_syncall() to
xfs_qm_sync().
SGI-PV: 969769
SGI-Modid: xfs-linux-melb:xfs-kern:29908a
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
Now that nfsd has stopped writing to the find_exported_dentry member we an
mark the export_operations const
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Neil Brown <neilb@suse.de>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: <linux-ext4@vger.kernel.org>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: David Chinner <dgc@sgi.com>
Cc: Timothy Shimmin <tes@sgi.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Chris Mason <mason@suse.com>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: "Vladimir V. Saveliev" <vs@namesys.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This one is a lot more complicated than the previous ones. XFS already had a
very clever scheme for supporting 64bit inode numbers in filehandles, and I've
reworked this to be some kind of a prototype for the generic 64bit inode
filehandle support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Neil Brown <neilb@suse.de>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: David Chinner <dgc@sgi.com>
Cc: Timothy Shimmin <tes@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently XFs has three different fid types: struct fid, struct xfs_fid
and struct xfs_fid2 with hte latter two beeing identicaly and the first
one beeing the same size but an unstructured array with the same size.
This patch consolidates all this to alway uuse struct xfs_fid.
This patch is required for an upcoming patch series from me that revamps
the nfs exporting code and introduces a Linux-wide struct fid.
SGI-PV: 970336
SGI-Modid: xfs-linux-melb:xfs-kern:29651a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
Fixup for lack of dmapi support and no quota module support.
SGI-PV: 969985
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6: (59 commits)
[XFS] eagerly remove vmap mappings to avoid upsetting Xen
[XFS] simplify validata_fields
[XFS] no longer using io_vnode, as was remaining from 23 cherrypick
[XFS] Remove STATIC which was missing from prior manual merge
[XFS] Put back the QUEUE_ORDERED_NONE test in the barrier check.
[XFS] Turn off XBF_ASYNC flag before re-reading superblock.
[XFS] avoid race in sync_inodes() that can fail to write out all dirty data
[XFS] This fix prevents bulkstat from spinning in an infinite loop.
[XFS] simplify xfs_create/mknod/symlink prototype
[XFS] avoid xfs_getattr in XFS_IOC_FSGETXATTR ioctl
[XFS] get_bulkall() could return incorrect inode state
[XFS] Kill unused IOMAP_EOF flag
[XFS] fix when DMAPI mount option processing happens
[XFS] ensure file size is logged on synchronous writes
[XFS] growlock should be a mutex
[XFS] replace some large xfs_log_priv.h macros by proper functions
[XFS] kill struct bhv_vfs
[XFS] move syncing related members from struct bhv_vfs to struct xfs_mount
[XFS] kill the vfs_flags member in struct bhv_vfs
[XFS] kill the vfs_fsid and vfs_altfsid members in struct bhv_vfs
...
|
|
I_LOCK was used for several unrelated purposes, which caused deadlock
situations in certain filesystems as a side effect. One of the purposes
now uses the new I_SYNC bit.
Also document the various bits and change their order from historical to
logical.
[bunk@stusta.de: make fs/inode.c:wake_up_inode() static]
Signed-off-by: Joern Engel <joern@wohnheim.fh-wedel.de>
Cc: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Cc: David Chinner <dgc@sgi.com>
Cc: Anton Altaparmakov <aia21@cam.ac.uk>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Miklos Szeredi <miklos@szeredi.hu> and me identified a writeback bug:
> The following strange behavior can be observed:
>
> 1. large file is written
> 2. after 30 seconds, nr_dirty goes down by 1024
> 3. then for some time (< 30 sec) nothing happens (disk idle)
> 4. then nr_dirty again goes down by 1024
> 5. repeat from 3. until whole file is written
>
> So basically a 4Mbyte chunk of the file is written every 30 seconds.
> I'm quite sure this is not the intended behavior.
It can be produced by the following test scheme:
# cat bin/test-writeback.sh
grep nr_dirty /proc/vmstat
echo 1 > /proc/sys/fs/inode_debug
dd if=/dev/zero of=/var/x bs=1K count=204800&
while true; do grep nr_dirty /proc/vmstat; sleep 1; done
# bin/test-writeback.sh
nr_dirty 19207
nr_dirty 19207
nr_dirty 30924
204800+0 records in
204800+0 records out
209715200 bytes (210 MB) copied, 1.58363 seconds, 132 MB/s
nr_dirty 47150
nr_dirty 47141
nr_dirty 47142
nr_dirty 47142
nr_dirty 47142
nr_dirty 47142
nr_dirty 47205
nr_dirty 47214
nr_dirty 47214
nr_dirty 47214
nr_dirty 47214
nr_dirty 47214
nr_dirty 47215
nr_dirty 47216
nr_dirty 47216
nr_dirty 47216
nr_dirty 47154
nr_dirty 47143
nr_dirty 47143
nr_dirty 47143
nr_dirty 47143
nr_dirty 47143
nr_dirty 47142
nr_dirty 47142
nr_dirty 47142
nr_dirty 47142
nr_dirty 47134
nr_dirty 47134
nr_dirty 47135
nr_dirty 47135
nr_dirty 47135
nr_dirty 46097 <== -1038
nr_dirty 46098
nr_dirty 46098
nr_dirty 46098
[...]
nr_dirty 46091
nr_dirty 46092
nr_dirty 46092
nr_dirty 45069 <== -1023
nr_dirty 45056
nr_dirty 45056
nr_dirty 45056
[...]
nr_dirty 37822
nr_dirty 36799 <== -1023
[...]
nr_dirty 36781
nr_dirty 35758 <== -1023
[...]
nr_dirty 34708
nr_dirty 33672 <== -1024
[...]
nr_dirty 33692
nr_dirty 32669 <== -1023
% ls -li /var/x
847824 -rw-r--r-- 1 root root 200M 2007-08-12 04:12 /var/x
% dmesg|grep 847824 # generated by a debug printk
[ 529.263184] redirtied inode 847824 line 548
[ 564.250872] redirtied inode 847824 line 548
[ 594.272797] redirtied inode 847824 line 548
[ 629.231330] redirtied inode 847824 line 548
[ 659.224674] redirtied inode 847824 line 548
[ 689.219890] redirtied inode 847824 line 548
[ 724.226655] redirtied inode 847824 line 548
[ 759.198568] redirtied inode 847824 line 548
# line 548 in fs/fs-writeback.c:
543 if (wbc->pages_skipped != pages_skipped) {
544 /*
545 * writeback is not making progress due to locked
546 * buffers. Skip this inode for now.
547 */
548 redirty_tail(inode);
549 }
More debug efforts show that __block_write_full_page()
never has the chance to call submit_bh() for that big dirty file:
the buffer head is *clean*. So basicly no page io is issued by
__block_write_full_page(), hence pages_skipped goes up.
Also the comment in generic_sync_sb_inodes():
544 /*
545 * writeback is not making progress due to locked
546 * buffers. Skip this inode for now.
547 */
and the comment in __block_write_full_page():
1713 /*
1714 * The page was marked dirty, but the buffers were
1715 * clean. Someone wrote them back by hand with
1716 * ll_rw_block/submit_bh. A rare case.
1717 */
do not quite agree with each other. The page writeback should be skipped for
'locked buffer', but here it is 'clean buffer'!
This patch fixes this bug. Though I'm not sure why __block_write_full_page()
is called only to do nothing and who actually issued the writeback for us.
This is the two possible new behaviors after the patch:
1) pretty nice: wait 30s and write ALL:)
2) not so good:
- during the dd: ~16M
- after 30s: ~4M
- after 5s: ~4M
- after 5s: ~176M
The next patch will fix case (2).
Cc: David Chinner <dgc@sgi.com>
Cc: Ken Chen <kenchen@google.com>
Signed-off-by: Fengguang Wu <wfg@mail.ustc.edu.cn>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Slab constructors currently have a flags parameter that is never used. And
the order of the arguments is opposite to other slab functions. The object
pointer is placed before the kmem_cache pointer.
Convert
ctor(void *object, struct kmem_cache *s, unsigned long flags)
to
ctor(struct kmem_cache *s, void *object)
throughout the kernel
[akpm@linux-foundation.org: coupla fixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
XFS leaves stray mappings around when it vmaps memory to make it virtually
contigious. This upsets Xen if one of those pages is being recycled into a
pagetable, since it finds an extra writable mapping of the page.
This patch solves the problem in a brute force way, by making XFS always
eagerly unmap its mappings.
SGI-PV: 971902
SGI-Modid: xfs-linux-melb:xfs-kern:29886a
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
Stop using xfs_getattr and a onstack bhv_vattr_t just to get three fields
from the underlying inode and opencode copying from the inode fields
instead.
SGI-PV: 970662
SGI-Modid: xfs-linux-melb:xfs-kern:29711a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: David Chinner <dgc@sgi.com>
Cc: Timothy Shimmin <tes@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Because we cherrypicked SGI-Modid xfs-linux-melb:xfs-kern:29675a
and it depended on the sgi mod which removed io_vnode (which was
not cherrypicked in 23) it was hand modified.
This fixes things back up (to the originial mod) now we have moved
on again.
Reviewed-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
Removes STATIC on xfs_freeze function which was not manually
applied for SGI-Modid: xfs-linux-melb:xfs-kern:29504a.
Reviewed-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
Put back the QUEUE_ORDERED_NONE test which caused us grief in sles when it
was taken out as, IIRC, it allowed md/lvm to be thought of as supporting
barriers when they weren't in some configurations. This patch will be
reverting what went in as part of a change for the SGI-pv 964544
(SGI-Modid: xfs-linux-melb:xfs-kern:28568a).
SGI-PV: 971783
SGI-Modid: xfs-linux-melb:xfs-kern:29882a
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
|
|
SGI-PV: 971603
SGI-Modid: xfs-linux-melb:xfs-kern:29871a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
In xfs_fs_sync_super() treat a sync the same as a filesystem freeze. This
is needed to force the log to disk for inodes which are not marked dirty
in the Linux inode (the inodes are marked dirty on completion of the log
I/O) and so sync_inodes() will not flush them.
In xfs_fs_write_inode() a synchronous flush will not get an EAGAIN from
xfs_inode_flush() and if an asynchronous flush returns EAGAIN we should
pass it on to the caller. If we get an error while flushing the inode then
re-dirty it so we can try again later.
SGI-PV: 971670
SGI-Modid: xfs-linux-melb:xfs-kern:29860a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
Here 'agino' increments through the inodes in an allocation group. At the
end of the innermost 'for' loop it will hold the value of the next inode
to look at (ie the first inode in the next cluster/chunk). Assigning
'lastino' to 'agino' resets it to the last inode in the last inode cluster
we just looked at. This causes us to look up the very same cluster and
examine all the inodes all over again, and again, and again...
We also want to set 'lastino' for the cases when we're not interested in
the inode so that the next call to bulkstat won't re-examine the same
uninteresting inodes.
SGI-PV: 971064
SGI-Modid: xfs-linux-melb:xfs-kern:29840a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
Simplify the prototype for xfs_create/xfs_mkdir/xfs_symlink by not passing
down a bhv_vattr_t that just hogs stack space. Instead pass down the mode
in a mode_t and in case of xfs_create the rdev as a scalar type as well.
SGI-PV: 968563
SGI-Modid: xfs-linux-melb:xfs-kern:29794a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
No need to call into xfs_getattr and put a big bhv_vattr_t on the stack
just to get a little information from the XFS inode.
Add a helper called xfs_ioc_fsgetxattr instead that deals with retrieving
the information in a clean way.
SGI-PV: 968563
SGI-Modid: xfs-linux-melb:xfs-kern:29780a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
In the following scenario xfs_bulkstat() returns incorrect stale inode
state:
1. File_A is created and its inode synced to disk. 2. File_A is unlinked
and doesn't exist anymore. 3. Filesystem sync is invoked. 4. File_B is
created. File_B happens to reclaim File_A's inode. 5. xfs_bulkstat() is
called and detects File_B but reports the
incorrect File_A inode state.
Explanation for the incorrect inode state is that inodes are not
immediately synced on file create for performance reasons. This leaves the
on-disk inode buffer uninitialized (or with old state from a previous
generation inode) and this is what xfs_bulkstat() would report.
The patch marks the on-disk inode buffer "dirty" on unlink. When the inode
is reclaimed (by a new file create), xfs_bulkstat() would filter this
inode by the "dirty" mark. Once the inode is flushed to disk, the on-disk
buffer "dirty" mark is automatically removed and a following
xfs_bulkstat() would return the correct inode state.
Marking the on-disk inode buffer "dirty" on unlink is achieved by setting
the on-disk di_nlink field to 0. Note that the in-core di_nlink has
already been set to 0 and a corresponding transaction logged by
xfs_droplink(). This is an exception from the rule that any on-disk inode
buffer changes has to be followed by a disk write (inode flush).
Synchronizing the in-core to on-disk di_nlink values in advance (before
the actual inode flush to disk) should be fine in this case because the
inode is already unlinked and it would never change its di_nlink again for
this inode generation.
SGI-PV: 970842
SGI-Modid: xfs-linux-melb:xfs-kern:29757a
Signed-off-by: Vlad Apostolov <vapo@sgi.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Mark Goodwin <markgw@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
SGI-PV: 968563
SGI-Modid: xfs-linux-melb:xfs-kern:29705a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
Fix for a regression caused by a recent patch
that moved the DMAPI mount option processing inside xfs_parseargs(). The
DMAPI mount option used to be processed in the DMAPI module loaded before
xfs_parseargs() was invoked.
SGI-PV: 970451
SGI-Modid: xfs-linux-melb:xfs-kern:29683a
Signed-off-by: Vlad Apostolov <vapo@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
Synchronous writes currently log inode changes before syncing pages to
disk. Since the file size is updated on I/O completion we wont be writing
out the updated file size and if we crash the file will have the wrong
size. This change moves the logging after the syncing of the pages to
ensure we log the correct file size.
SGI-PV: 970334
SGI-Modid: xfs-linux-melb:xfs-kern:29649a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
m_growlock only needs plain binary mutex semantics, so use a struct mutex
instead of a semaphore for it.
SGI-PV: 968563
SGI-Modid: xfs-linux-melb:xfs-kern:29512a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
... or in the case of XLOG_TIC_ADD_OPHDR remove a useless macro entirely.
SGI-PV: 968563
SGI-Modid: xfs-linux-melb:xfs-kern:29511a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
Now that struct bhv_vfs doesn't have any members left we can kill it and
go directly from the super_block to the xfs_mount everywhere.
SGI-PV: 969608
SGI-Modid: xfs-linux-melb:xfs-kern:29509a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
SGI-PV: 969608
SGI-Modid: xfs-linux-melb:xfs-kern:29508a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
All flags are added to xfs_mount's m_flag instead. Note that the 32bit
inode flag was duplicated in both of them, but only cleared in the mount
when it was not nessecary due to the filesystem beeing small enough. Two
flags are still required here - one to indicate the mount option setting,
and one to indicate if it applies or not.
SGI-PV: 969608
SGI-Modid: xfs-linux-melb:xfs-kern:29507a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
vfs_altfsid was just a pointer to mp->m_fixedfsid so we can trivially
replace it with the latter. vfs_fsid also was identical to m_fixedfsid
through rather obfuscated ways so we can kill it as well and simply its
only user.
SGI-PV: 969608
SGI-Modid: xfs-linux-melb:xfs-kern:29506a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
Also remove the now dead behavior code.
SGI-PV: 969608
SGI-Modid: xfs-linux-melb:xfs-kern:29505a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
All vfs ops now take struct xfs_mount pointers and the behaviour related
glue is split out into methods of its own.
SGI-PV: 969608
SGI-Modid: xfs-linux-melb:xfs-kern:29504a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
Mount options are now parsed by the main XFS module and rejected if quota
support is not available, and there are some new quota operation for the
quotactl syscall and calls to quote in the mount, unmount and sync
callchains.
SGI-PV: 969608
SGI-Modid: xfs-linux-melb:xfs-kern:29503a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
Mount options are now parsed by the main XFS module and rejected if dmapi
support is not available, and there is a new dm operation to send the
mount event.
SGI-PV: 969608
SGI-Modid: xfs-linux-melb:xfs-kern:29502a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
|
In the next patch we need to look at the mount structure until just before
it's freed, so we need to be able to free it as the very last thing in
xfs_unmount.
SGI-PV: 969608
SGI-Modid: xfs-linux-melb:xfs-kern:29501a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
|
