| Age | Commit message (Collapse) | Author |
|---|
|
* git://git.linux-nfs.org/pub/linux/nfs-2.6:
MAINTAINERS: update the NFS CLIENT entry
NFS: Fix an Oops in NFS unmount
Revert "NFS: Ensure we return zero if applications attempt to write zero bytes"
SUNRPC xprtrdma: fix XDR tail buf marshalling for all ops
NFSv2/v3: Fix a memory leak when using -onolock
NFS: Fix NFS mountpoint crossing...
|
|
ocfs2_extend_trans() might call journal_restart() which will commit dirty
buffers and then restart the transaction. This means that any buffers which
still need changes should be passed to journal_access() again. Some paths
during extend weren't doing this right.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
The nastiest cases of transaction extends are also the rarest. We can expose
them more quickly at the expense of performance by going straight to the
journal_restart() in ocfs2_extend_trans(). Wrap things in OCFS2_DEBUG_FS so
that we only do this when "expensive debugging" is turned on.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
This BUG_ON() was unintentionally left in after the sparse file support was
written.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
We're holding the cluster lock when a failure might happen in
ocfs2_dir_foreach() so it needs to be released.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
Ensure that the dummy 'root dentry' is invisible to d_find_alias(). If not,
then it may be spliced into the tree if a parent directory from the same
filesystem gets mounted at a later time.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
This reverts commit b9148c6b80d802dbc2a7530b29915a80432e50c7.
On Wed, 12 Dec 2007 10:57:30 -0500, Chuck Lever wrote
> commit b9148c6b should be reverted. It was recently forward-ported
> from some years-old patches, and is clearly not needed now.
>
> On Dec 11, 2007, at 5:21 PM, Adrian Bunk wrote:
>
>> This code became dead after commit
>> b9148c6b80d802dbc2a7530b29915a80432e50c7
>> (which BTW doesn't seem to have changed any behaviour) and can
>> therefore
>> be removed.
>>
>> Spotted by the Coverity checker.
>>
>> Signed-off-by: Adrian Bunk <bunk@kernel.org>
>>
>> ---
>> --- linux-2.6/fs/nfs/direct.c.old 2007-12-02 21:54:53.000000000 +0100
>> +++ linux-2.6/fs/nfs/direct.c 2007-12-02 21:55:10.000000000 +0100
>> @@ -897,15 +897,12 @@ ssize_t nfs_file_direct_write(struct kio
>> if (!count)
>> goto out; /* return 0 */
>>
>> retval = -EINVAL;
>> if ((ssize_t) count < 0)
>> goto out;
>> - retval = 0;
>> - if (!count)
>> - goto out;
>>
>> retval = nfs_sync_mapping(mapping);
>> if (retval)
>> goto out;
>>
>> retval = nfs_direct_write(iocb, iov, nr_segs, pos, count);
>>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Neil Brown said:
> Hi Trond,
>
> We found that a machine which made moderately heavy use of
> 'automount' was leaking some nfs data structures - particularly the
> 4K allocated by rpc_alloc_iostats.
> It turns out that this only happens with filesystems with -onolock
> set.
> The problem is that if NFS_MOUNT_NONLM is set, nfs_start_lockd doesn't
> set server->destroy, so when the filesystem is unmounted, the
> ->client_acl is not shutdown, and so several resources are still
> held. Multiple mount/umount cycles will slowly eat away memory
> several pages at a time.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: NeilBrown <neilb@suse.de>
|
|
The check that was added to nfs_xdev_get_sb() to work around broken
servers, works fine for NFSv2, but causes mountpoint crossing on NFSv3 to
always return ESTALE.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
Ultimately to implement /proc perfectly we need an implementation of
d_revalidate because files and directories can be removed behind the back
of the VFS, and d_revalidate is the only way we can let the VFS know that
this has happened.
Unfortunately the linux VFS can not cope with anything in the path to a
mount point going away. So a proper d_revalidate method that calls d_drop
also needs to call have_submounts which is moderately expensive, so you
really don't want a d_revalidate method that unconditionally calls it, but
instead only calls it when the backing object has really gone away.
proc generic entries only disappear on module_unload (when not counting the
fledgling network namespace) so it is quite rare that we actually encounter
that case and has not actually caused us real world trouble yet.
So until we get a proper test for keeping dentries in the dcache fix the
current d_revalidate method by completely removing it. This returns us to
the current status quo.
So with CONFIG_NETNS=n things should look as they have always looked.
For CONFIG_NETNS=y things work most of the time but there are a few rare
corner cases that don't behave properly. As the network namespace is
barely present in 2.6.24 this should not be a problem.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "Denis V. Lunev" <den@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
[XFS] Fix xfs_ichgtime()s broken usage of I_SYNC
[XFS] Make xfsbufd threads freezable
[XFS] revert to double-buffering readdir
[XFS] Fix broken inode cluster setup.
[XFS] Clear XBF_READ_AHEAD flag on I/O completion.
[XFS] Fixed a few bugs in xfs_buf_associate_memory()
[XFS] 971064 Various fixups for xfs_bulkstat().
[XFS] Fix dbflush panic in xfs_qm_sync.
|
|
The recent I_LOCK->I_SYNC changes mistakenly changed xfs_ichgtime to look
at I_SYNC instead of I_LOCK. This was incorrect and prevents newly created
inodes from moving to the dirty list. Change this to the correct check
which is for I_NEW, not I_LOCK or I_SYNC so that behaviour is correct.
SGI-PV: 974225
SGI-Modid: xfs-linux-melb:xfs-kern:30204a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
Fix breakage caused by commit 831441862956fffa17b9801db37e6ea1650b0f69
that did not introduce the necessary call to set_freezable() in
xfs/linux-2.6/xfs_buf.c .
SGI-PV: 974224
SGI-Modid: xfs-linux-melb:xfs-kern:30203a
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
The current readdir implementation deadlocks on a btree buffers locks
because nfsd calls back into ->lookup from the filldir callback. The only
short-term fix for this is to revert to the old inefficient
double-buffering scheme.
SGI-PV: 973377
SGI-Modid: xfs-linux-melb:xfs-kern:30201a
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
The radix tree based inode caches did away with the inode cluster hashes,
replacing them with a bunch of masking and gang lookups on the radix tree.
This masking got broken when moving the code to per-ag radix trees and
indexing by agino # rather than straight inode number. The result is
clustered inode writeback does not cluster and things can go extremely
slowly when there are lots of inodes to write.
Fix it up by comparing the agino # of the inode we just looked up to the
index of the cluster we are looking for.
Tested-by: Torsten Kaiser <just.for.lkml@googlemail.com>
SGI-PV: 972915
SGI-Modid: xfs-linux-melb:xfs-kern:30033a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
SGI-PV: 972554
SGI-Modid: xfs-linux-melb:xfs-kern:30128a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
|
|
- calculation of 'page_count' was incorrect as it did not
consider the offset of 'mem' into the first page. The
logic to bump 'page_count' didn't work if 'len' was <=
PAGE_CACHE_SIZE (ie offset = 3k, len = 2k).
- setting b_buffer_length to 'len' is incorrect if 'offset'
is > 0. Set it to the total length of the buffer.
- I suspect that passing a non-aligned address into
mem_to_page() for the first page may have been causing
issues - don't know but just tidy up that code anyway.
SGI-PV: 971596
SGI-Modid: xfs-linux-melb:xfs-kern:30143a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
|
|
- sanity check for NULL user buffer in xfs_ioc_bulkstat[_compat]()
- remove the special case for XFS_IOC_FSBULKSTAT with count == 1. This
special case causes bulkstat to fail because the special case uses
xfs_bulkstat_single() instead of xfs_bulkstat() and the two functions
have different semantics. xfs_bulkstat() will return the next inode
after the one supplied while skipping internal inodes (ie quota inodes).
xfs_bulkstate_single() will only lookup the inode supplied and return
an error if it is an internal inode.
- in xfs_bulkstat(), need to initialise 'lastino' to the inode supplied
so in cases were we return without examining any inodes the scan wont
restart back at zero.
- sanity check for valid *ubcountp values. Cannot sanity check for valid
ubuffer here because some users of xfs_bulkstat() don't supply a buffer.
- checks against 'ubleft' (the space left in the user's buffer) should be
against 'statstruct_size' which is the supplied minimum object size.
The mixture of checks against statstruct_size and 0 was one of the
reasons we were skipping inodes.
- if the formatter function returns BULKSTAT_RV_NOTHING and an error and
the error is not ENOENT or EINVAL then we need to abort the scan. ENOENT
is for inodes that are no longer valid and we just skip them. EINVAL is
returned if we try to lookup an internal inode so we skip them too. For
a DMF scan if the inode and DMF attribute cannot fit into the space left
in the user's buffer it would return ERANGE. We didn't handle this error
and skipped the inode. We would continue to skip inodes until one fitted
into the user's buffer or we completed the scan.
- put back the recalculation of agino (that got removed with the last fix)
at the end of the while loop. This is because the code at the start of
the loop expects agino to be the last inode examined if it is non-zero.
- if we found some inodes but then encountered an error, return success
this time and the error next time. If the formatter aborted with ENOMEM
we will now return this error but only if we couldn't read any inodes.
Previously if we encountered ENOMEM without reading any inodes we
returned a zero count and no error which falsely indicated the scan was
complete.
SGI-PV: 973431
SGI-Modid: xfs-linux-melb:xfs-kern:30089a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
|
|
The recent behaviour layer removal dropped the check for quotas that have
been requested at mount time but have subsequently been turned off. This
results in a panic when accessing m_quotainfo which has been freed.
This patch adds the check originally made by xfs_qm_syncall() to
xfs_qm_sync().
SGI-PV: 969769
SGI-Modid: xfs-linux-melb:xfs-kern:29908a
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
|
|
|
|
endianness annotations in networking code had been in place for quite a
while; in particular, sin_port and s_addr are annotated as big-endian.
Code in ocfs2 had __force casts added apparently to shut the sparse
warnings up; of course, these days they only serve to *produce* warnings
for no reason whatsoever...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
BFS_FILEBLOCKS() expects struct bfs_inode * (on-disk data, with little-
endian fields), not struct bfs_inode_info * (in-core stuff, with host-
endian ones).
It's a macro and fields with the right names are present in
bfs_inode_info, so it compiles, but on big-endian host it gives bogus
results.
Introduced in commit f433dc56344cb72cc3de5ba0819021cec3aef807 ("Fixes to
the BFS filesystem driver").
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
access_flags_to_mode() gets on-the-wire data (little-endian) and treats
it as host-endian.
Introduced in commit e01b64001359034d04c695388870936ed3d1b56b ("[CIFS]
enable get mode from ACL when cifsacl mount option specified")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Creating PDEs with refcount 0 and "deleted" flag has problems (see below).
Switch to usual scheme:
* PDE is created with refcount 1
* every de_get does +1
* every de_put() and remove_proc_entry() do -1
* once refcount reaches 0, PDE is freed.
This elegantly fixes at least two following races (both observed) without
introducing new locks, without abusing old locks, without spreading
lock_kernel():
1) PDE leak
remove_proc_entry de_put
----------------- ------
[refcnt = 1]
if (atomic_read(&de->count) == 0)
if (atomic_dec_and_test(&de->count))
if (de->deleted)
/* also not taken! */
free_proc_entry(de);
else
de->deleted = 1;
[refcount=0, deleted=1]
2) use after free
remove_proc_entry de_put
----------------- ------
[refcnt = 1]
if (atomic_dec_and_test(&de->count))
if (atomic_read(&de->count) == 0)
free_proc_entry(de);
/* boom! */
if (de->deleted)
free_proc_entry(de);
BUG: unable to handle kernel paging request at virtual address 6b6b6b6b
printing eip: c10acdda *pdpt = 00000000338f8001 *pde = 0000000000000000
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: af_packet ipv6 cpufreq_ondemand loop serio_raw psmouse k8temp hwmon sr_mod cdrom
Pid: 23161, comm: cat Not tainted (2.6.24-rc2-8c0863403f109a43d7000b4646da4818220d501f #4)
EIP: 0060:[<c10acdda>] EFLAGS: 00210097 CPU: 1
EIP is at strnlen+0x6/0x18
EAX: 6b6b6b6b EBX: 6b6b6b6b ECX: 6b6b6b6b EDX: fffffffe
ESI: c128fa3b EDI: f380bf34 EBP: ffffffff ESP: f380be44
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process cat (pid: 23161, ti=f380b000 task=f38f2570 task.ti=f380b000)
Stack: c10ac4f0 00000278 c12ce000 f43cd2a8 00000163 00000000 7da86067 00000400
c128fa20 00896b18 f38325a8 c128fe20 ffffffff 00000000 c11f291e 00000400
f75be300 c128fa20 f769c9a0 c10ac779 f380bf34 f7bfee70 c1018e6b f380bf34
Call Trace:
[<c10ac4f0>] vsnprintf+0x2ad/0x49b
[<c10ac779>] vscnprintf+0x14/0x1f
[<c1018e6b>] vprintk+0xc5/0x2f9
[<c10379f1>] handle_fasteoi_irq+0x0/0xab
[<c1004f44>] do_IRQ+0x9f/0xb7
[<c117db3b>] preempt_schedule_irq+0x3f/0x5b
[<c100264e>] need_resched+0x1f/0x21
[<c10190ba>] printk+0x1b/0x1f
[<c107c8ad>] de_put+0x3d/0x50
[<c107c8f8>] proc_delete_inode+0x38/0x41
[<c107c8c0>] proc_delete_inode+0x0/0x41
[<c1066298>] generic_delete_inode+0x5e/0xc6
[<c1065aa9>] iput+0x60/0x62
[<c1063c8e>] d_kill+0x2d/0x46
[<c1063fa9>] dput+0xdc/0xe4
[<c10571a1>] __fput+0xb0/0xcd
[<c1054e49>] filp_close+0x48/0x4f
[<c1055ee9>] sys_close+0x67/0xa5
[<c10026b6>] sysenter_past_esp+0x5f/0x85
=======================
Code: c9 74 0c f2 ae 74 05 bf 01 00 00 00 4f 89 fa 5f 89 d0 c3 85 c9 57 89 c7 89 d0 74 05 f2 ae 75 01 4f 89 f8 5f c3 89 c1 89 c8 eb 06 <80> 38 00 74 07 40 4a 83 fa ff 75 f4 29 c8 c3 90 90 90 57 83 c9
EIP: [<c10acdda>] strnlen+0x6/0x18 SS:ESP 0068:f380be44
Also, remove broken usage of ->deleted from reiserfs: if sget() succeeds,
module is already pinned and remove_proc_entry() can't happen => nobody
can mark PDE deleted.
Dummy proc root in netns code is not marked with refcount 1. AFAICS, we
never get it, it's just for proper /proc/net removal. I double checked
CLONE_NETNS continues to work.
Patch survives many hours of modprobe/rmmod/cat loops without new bugs
which can be attributed to refcounting.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Before we start committing a transaction, we call
__journal_clean_checkpoint_list() to cleanup transaction's written-back
buffers.
If this call happens to remove all of them (and there were already some
buffers), __journal_remove_checkpoint() will decide to free the transaction
because it isn't (yet) a committing transaction and soon we fail some
assertion - the transaction really isn't ready to be freed :).
We change the check in __journal_remove_checkpoint() to free only a
transaction in T_FINISHED state. The locking there is subtle though (as
everywhere in JBD ;(). We use j_list_lock to protect the check and a
subsequent call to __journal_drop_transaction() and do the same in the end
of journal_commit_transaction() which is the only place where a transaction
can get to T_FINISHED state.
Probably I'm too paranoid here and such locking is not really necessary -
checkpoint lists are processed only from log_do_checkpoint() where a
transaction must be already committed to be processed or from
__journal_clean_checkpoint_list() where kjournald itself calls it and thus
transaction cannot change state either. Better be safe if something
changes in future...
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes regression, introduced since 2.6.16. NextStep variant of
UFS as OpenStep uses directory block size equals to 1024. Without this
change, ufs_check_page fails in many cases.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Evgeniy Dushistov <dushistov@mail.ru>
Cc: Dave Bailey <dsbailey@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On 2.6.24, top started showing 100% iowait on one CPU when a UML instance was
running (but completely idle). The UML code sits in io_getevents waiting for
an event to be submitted and completed.
Fix this by checking ctx->reqs_active before scheduling to determine whether
or not we are waiting for I/O.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Cc: Zach Brown <zach.brown@oracle.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix breakage caused by commit d5d8c5976d6adeddb8208c240460411e2198b393
"freezer: do not send signals to kernel threads" in
jffs2_garbage_collect_thread() that assumed it would be sent signals
by the freezer.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Pete MacKay <armlinux@architechnical.net>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6: (27 commits)
[INET]: Fix inet_diag dead-lock regression
[NETNS]: Fix /proc/net breakage
[TEXTSEARCH]: Do not allow zero length patterns in the textsearch infrastructure
[NETFILTER]: fix forgotten module release in xt_CONNMARK and xt_CONNSECMARK
[NETFILTER]: xt_TCPMSS: remove network triggerable WARN_ON
[DECNET]: dn_nl_deladdr() almost always returns no error
[IPV6]: Restore IPv6 when MTU is big enough
[RXRPC]: Add missing select on CRYPTO
mac80211: rate limit wep decrypt failed messages
rfkill: fix double-mutex-locking
mac80211: drop unencrypted frames if encryption is expected
mac80211: Fix behavior of ieee80211_open and ieee80211_close
ieee80211: fix unaligned access in ieee80211_copy_snap
mac80211: free ifsta->extra_ie and clear IEEE80211_STA_PRIVACY_INVOKED
SCTP: Fix build issues with SCTP AUTH.
SCTP: Fix chunk acceptance when no authenticated chunks were listed.
SCTP: Fix the supported extensions paramter
SCTP: Fix SCTP-AUTH to correctly add HMACS paramter.
SCTP: Fix the number of HB transmissions.
[TCP] illinois: Incorrect beta usage
...
|
|
Well I clearly goofed when I added the initial network namespace support
for /proc/net. Currently things work but there are odd details visible to
user space, even when we have a single network namespace.
Since we do not cache proc_dir_entry dentries at the moment we can just
modify ->lookup to return a different directory inode depending on the
network namespace of the process looking at /proc/net, replacing the
current technique of using a magic and fragile follow_link method.
To accomplish that this patch:
- introduces a shadow_proc method to allow different dentries to
be returned from proc_lookup.
- Removes the old /proc/net follow_link magic
- Fixes a weakness in our not caching of proc generic dentries.
As shadow_proc uses a task struct to decided which dentry to return we can
go back later and fix the proc generic caching without modifying any code
that uses the shadow_proc method.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Pavel Emelyanov <xemul@openvz.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Make them depend on TCGETS2. If that one is implemented the rest should be
there as well.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Invalidate attributes on rename, since some filesystems may update
st_ctime. Reported by Szabolcs Szakacsits
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I found problems accessing (executing) previously existing files, until
I did chmod on them (or setattr).
If the fi->attr_version is not initialized, then it could be
larger than fc->attr_version until a setattr is executed, and as a
result the inode attributes would never be set.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
FUSE_FILE_OPS is meant to signal that the kernel will send the open file to to
the userspace filesystem for operations on open files, so that sillyrenaming
unlinked files becomes unnecessary.
However this needs VFS changes, which won't make it into 2.6.24.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some open flags (O_APPEND, O_DIRECT) can be changed with fcntl(F_SETFL, ...)
after open, but fuse currently only sends the flags to userspace in open.
To make it possible to correcly handle changing flags, send the
current value to userspace in each read and write.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Extract repeated code into helper function, as suggested by Akpm.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently reading a fuse file will stop at cached i_size and return
EOF, even though the file might have grown since the attributes were
last updated.
So detect if trying to read past EOF, and refresh the attributes
before continuing with the read.
Thanks to mpb for the report.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In commit a686cd898bd999fd026a51e90fb0a3410d258ddb:
"Val's cross-port of the ext3 reservations code into ext2."
include/linux/ext2_fs.h got a new function whose return value is only
defined if __KERNEL__ is defined. Putting #ifdef __KERNEL__ around the
function seems to help, patch below.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Oleg noticed that the call of task_pid_nr_ns() in proc_pid_readdir
is racy with respect to tasks exiting.
After a bit of examination it also appears that the call itself
is completely unnecessary.
So to fix the problem this patch modifies next_tgid() to return
both a tgid and the task struct in question.
A structure is introduced to return these values because it is
slightly cleaner and easier to optimize, and the resulting code
is a little shorter.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
proc_kill_inodes() can clear ->i_fop in the middle of vfs_readdir resulting in
NULL dereference during "file->f_op->readdir(file, buf, filler)".
The solution is to remove proc_kill_inodes() completely:
a) we don't have tricky modules implementing their tricky readdir hooks which
could keeping this revoke from hell.
b) In a situation when module is gone but PDE still alive, standard
readdir will return only "." and "..", because pde->next was cleared by
remove_proc_entry().
c) the race proc_kill_inode() destined to prevent is not completely
fixed, just race window made smaller, because vfs_readdir() is run
without sb_lock held and without file_list_lock held. Effectively,
->i_fop is cleared at random moment, which can't fix properly anything.
BUG: unable to handle kernel NULL pointer dereference at virtual address 00000018
printing eip: c1061205 *pdpt = 0000000005b22001 *pde = 0000000000000000
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: foo af_packet ipv6 cpufreq_ondemand loop serio_raw sr_mod k8temp cdrom hwmon amd_rng
Pid: 2033, comm: find Not tainted (2.6.24-rc1-b1d08ac064268d0ae2281e98bf5e82627e0f0c56 #2)
EIP: 0060:[<c1061205>] EFLAGS: 00010246 CPU: 0
EIP is at vfs_readdir+0x47/0x74
EAX: c6b6a780 EBX: 00000000 ECX: c1061040 EDX: c5decf94
ESI: c6b6a780 EDI: fffffffe EBP: c9797c54 ESP: c5decf78
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process find (pid: 2033, ti=c5dec000 task=c64bba90 task.ti=c5dec000)
Stack: c5decf94 c1061040 fffffff7 0805ffbc 00000000 c6b6a780 c1061295 0805ffbc
00000000 00000400 00000000 00000004 0805ffbc 4588eff4 c5dec000 c10026ba
00000004 0805ffbc 00000400 0805ffbc 4588eff4 bfdc6c70 000000dc 0000007b
Call Trace:
[<c1061040>] filldir64+0x0/0xc5
[<c1061295>] sys_getdents64+0x63/0xa5
[<c10026ba>] sysenter_past_esp+0x5f/0x85
=======================
Code: 49 83 78 18 00 74 43 8d 6b 74 bf fe ff ff ff 89 e8 e8 b8 c0 12 00 f6 83 2c 01 00 00 10 75 22 8b 5e 10 8b 4c 24 04 89 f0 8b 14 24 <ff> 53 18 f6 46 1a 04 89 c7 75 0b 8b 56 0c 8b 46 08 e8 c8 66 00
EIP: [<c1061205>] vfs_readdir+0x47/0x74 SS:ESP 0068:c5decf78
hch: "Nice, getting rid of this is a very good step formwards.
Unfortunately we have another copy of this junk in
security/selinux/selinuxfs.c:sel_remove_entries() which would need the
same treatment."
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Acked-by: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: James Morris <jmorris@namei.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
sysfs: fix off-by-one error in fill_read_buffer()
kobject: two typo fixes
UIO: add UIO documentation target to DocBook Makefile
UIO: fix up the UIO documentation
create /sys/.../power when CONFIG_PM is set
allow LEGACY_PTYS to be set to 0
|
|
I found that there is a off-by-one problem in the following code.
Version: 2.6.24-rc2
File: fs/sysfs/file.c:118-122
Function: fill_read_buffer
--------------------------------------------------------------------
count = ops->show(kobj, attr_sd->s_attr.attr, buffer->page);
sysfs_put_active_two(attr_sd);
BUG_ON(count > (ssize_t)PAGE_SIZE);
--------------------------------------------------------------------
Because according to the specification of the sysfs and the implement of
the show methods, the show methods return the number of bytes which would
be generated for the given input, excluding the trailing null.So if the
return value of the show methods equals PAGE_SIZE - 1, the buffer is full
in fact. And if the return value equals PAGE_SIZE, the resulting string
was already truncated,or buffer overflow occurred.
This patch fixes an off-by-one error in fill_read_buffer.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Tejun Heo <teheo@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
fix: http://bugzilla.kernel.org/show_bug.cgi?id=3043
only allow coredumping to the same uid that the coredumping
task runs under.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Al Viro <viro@ftp.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ocfs2_truncate() and ocfs2_remove_inode_range() had reversed their "set
i_size" arguments to ocfs2_truncate_inline(). Fix things so that truncate
sets i_size, and punching a hole ignores it.
This exposed a problem where punching a hole in an inline-data file wasn't
updating the page cache, so fix that too.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
This was causing us to prematurely push out inline data by one byte.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
The existing bug statement didn't take into account unhashed dentries which
might not have a cluster lock on them. This could happen if a node exporting
the file system via NFS is rebooted, re-exported to nfs clients and then
unmounted. It's fine in this case to not have a dentry cluster lock.
Just remove the bug statement and replace it with an error print, which
does the proper checks. Though we want to know if something has happened
which might have prevented a cluster lock from being created, it's
definitely not necessary to panic the machine for this.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
Enable expensive bitmap scanning only if DEBUG option is enabled.
The bitmap scanning quite loads the CPU and on my machine the write
throughput of dd if=/dev/zero of=/ocfs2/file bs=1M count=500 conv=sync
improves from 37 MB/s to 45.4 MB/s in local mode...
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
If the inode block isn't valid then we don't want to print the value from
that, instead print the block number which was passed in (which should
always be correct). Also, turn this into a debug print for now - folks who
hit an actual problem always have other logs indicating what the source is.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
It's almost never worth printing in that situation and we keep forgetting to
manually filter it out.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
|
