| Age | Commit message (Collapse) | Author |
|---|
|
Pull MTD changes from David Woodhouse:
- Artem's cleanup of the MTD API continues apace.
- Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst
others.
- More work on DiskOnChip G3, new driver for DiskOnChip G4.
- Clean up debug/warning printks in JFFS2 to use pr_<level>.
Fix up various trivial conflicts, largely due to changes in calling
conventions for things like dmaengine_prep_slave_sg() (new inline
wrapper to hide new parameter, clashing with rewrite of previously last
parameter that used to be an 'append' flag, and is now a bitmap of
'unsigned long flags').
(Also some header file fallout - like so many merges this merge window -
and silly conflicts with sparse fixes)
* tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits)
mtd: docg3 add protection against concurrency
mtd: docg3 refactor cascade floors structure
mtd: docg3 increase write/erase timeout
mtd: docg3 fix inbound calculations
mtd: nand: gpmi: fix function annotations
mtd: phram: fix section mismatch for phram_setup
mtd: unify initialization of erase_info->fail_addr
mtd: support ONFI multi lun NAND
mtd: sm_ftl: fix typo in major number.
mtd: add device-tree support to spear_smi
mtd: spear_smi: Remove default partition information from driver
mtd: Add device-tree support to fsmc_nand
mtd: fix section mismatch for doc_probe_device
mtd: nand/fsmc: Remove sparse warnings and errors
mtd: nand/fsmc: Add DMA support
mtd: nand/fsmc: Access the NAND device word by word whenever possible
mtd: nand/fsmc: Use dev_err to report error scenario
mtd: nand/fsmc: Use devm routines
mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform
mtd: fsmc_nand: add pm callbacks to support hibernation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
|
|
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
asm/system.h is a cause of circular dependency problems because it contains
commonly used primitive stuff like barrier definitions and uncommonly used
stuff like switch_to() that might require MMU definitions.
asm/system.h has been disintegrated by this point on all arches into the
following common segments:
(1) asm/barrier.h
Moved memory barrier definitions here.
(2) asm/cmpxchg.h
Moved xchg() and cmpxchg() here. #included in asm/atomic.h.
(3) asm/bug.h
Moved die() and similar here.
(4) asm/exec.h
Moved arch_align_stack() here.
(5) asm/elf.h
Moved AT_VECTOR_SIZE_ARCH here.
(6) asm/switch_to.h
Moved switch_to() here.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
This patch adds support to configure the SPEAr SMI driver via
device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch adds support to configure the FSMC NAND driver (used amongst
others on SPEAr platforms) via device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch removes the sparse below warnings and errors for nand/fsmc driver
/root/vipin/spear/kernel/3.3/linux-3.3/drivers/mtd/nand/fsmc_nand.c:363:31:
warning: incorrect type in initializer (different address spaces)
/root/vipin/spear/kernel/3.3/linux-3.3/drivers/mtd/nand/fsmc_nand.c:363:31:
expected struct fsmc_regs *regs
/root/vipin/spear/kernel/3.3/linux-3.3/drivers/mtd/nand/fsmc_nand.c:363:31:
got void [noderef] <asn:2>*regs_va
[...]
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The fsmc_nand driver uses cpu to read/write onto the device. This is inefficient
because of two reasons
- the cpu gets locked on AHB bus while reading from NAND
- the cpu is unnecessarily used when dma can do the job
This patch adds the support for accessing the device through DMA
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The default way of accessing nand device is using the nand width. This means
that 8bit devices are using u8 * and 16bit devices are accessed using u16 *.
This results in a non-optimal performance since the FSMC is designed to
translate the normal word accesses into device width based accesses. This patch
implements read_buf and write_buf callbacks using word by word accesses.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
FSMC controllers provide registers to program the required timing values for
attached NAND device. The timing values used until now are relaxed and should
work for all devices.
Although, for read/write performance improvements, the fsmc nand driver should
accept nand timings as a platform data and program the timing parameters into
fsmc registers accordingly.
This patch implements this modification. Additionally, it programs the default
timing parameters if these are not passed via platform data.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This adds 'ecc_strength' to struct mtd_info. This stores the maximum number of
bit errors that can be corrected in one writesize region.
For consistency with the nand code, 'strength' is similiarly added to struct
nand_ecc_ctrl. This stores the maximum number of bit errors that can be
corrected in one ecc step.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Adds power management code with fine granularity. Every flash control
command is enclosed by runtime_put()/get()s. To make sure that no
overhead is generated by too frequent power state switches, a quality of
service request is issued.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Address Latch Enable (ALE) and Command Latch Enable (CLE) defines are
platform specific and were wrongly put in driver specific fsmc.h file.
Move such defines to their respective platform.
Also instead of relying on fsmc driver, pass ALE, CLE offsets explicitly
from individual platform.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
ALE and CLE offsets can be different on different devices. Let devices
pass these offsets to the fsmc driver through platform data.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Add a register used in new FLCTL hardware and a feature flag for it.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Instead of reading out the register, use a cached value. This will
make way for a proper runtime power management implementation.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Add support for a new hardware generation. The meaning of some bits
of the FLCMNCR register changed, so some new defines are added
parallel to the existing ones to keep backward compatibility.
The defines allow to choose an appropriate clocking scheme.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch changes all the OTP functions like 'mtd_get_fact_prot_info()' and
makes them return zero immediately if the input 'len' parameter is 0. This is
not really needed currently, but most of the other functions do this, and it is
just consistent to do the same in the OTP functions.
This patch also moves the OTP functions from the header file to mtdcore.c
because they become a bit too big for being inlined.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This header is tiny and contains only pmc551-private stuff, so it should
not live in 'include/linux' - let's just merge it with pmc551.c.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Many drivers check whether the partition is R/O and return -EROFS if yes.
Let's stop having duplicated checks and move them to the API functions
instead.
And again a bit of noise - deleted few too sparse newlines, sorry.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Add verification of the offset and length to MTD API functions and verify that
MTD device offset and length are within MTD device size.
The modified API functions are:
'mtd_erase()'
'mtd_point()'
'mtd_unpoint()'
'mtd_get_unmapped_area()'
'mtd_read()'
'mtd_write()'
'mtd_panic_write()'
'mtd_lock()'
'mtd_unlock()'
'mtd_is_locked()'
'mtd_block_isbad()'
'mtd_block_markbad()'
This patch also uninlines these functions and exports in mtdcore.c because they
are not performance-critical and do not have to be inlined.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The 'mtd_unpoint()' API function should be able to return an error code because
it may fail if you specify incorrect offset. This patch changes this MTD API
function and amends all the drivers correspondingly.
Also return '-EOPNOTSUPP' from 'mtd_unpoint()' when the '->unpoint()' method is
undefined. We do not really need this currently, but this just makes
sense to be consistent with 'mtd_point()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Currently, the flash-based BBT implementation writes bad block data only
to its flash-based table and not to the OOB marker area. Then, as new bad
blocks are marked over time, the OOB markers become incomplete and the
flash-based table becomes the only source of current bad block
information. This becomes an obvious problem when, for example:
* bootloader cannot read the flash-based BBT format
* BBT is corrupted and the flash must be rescanned for bad
blocks; we want to remember bad blocks that were marked from Linux
So to keep the bad block markers in sync with the flash-based BBT, this
patch changes the default so that we write bad block markers to the proper
OOB area on each block in addition to flash-based BBT. Comments are
updated, expanded, and/or relocated as necessary.
The new flash-based BBT procedure for marking bad blocks:
(1) erase the affected block, to allow OOB marker to be written cleanly
(2) update in-memory BBT
(3) write bad block marker to OOB area of affected block
(4) update flash-based BBT
Note that we retain the first error encountered in (3) or (4), finish the
procedures, and dump the error in the end.
This should handle power cuts gracefully enough. (1) and (2) are mostly
harmless (note that (1) will not erase an already-recognized bad block).
The OOB and BBT may be "out of sync" if we experience power loss bewteen
(3) and (4), but we can reasonably expect that on next boot, subsequent
I/O operations will discover that the block should be marked bad again,
thus re-syncing the OOB and BBT.
Note that this is a change from the previous default flash-based BBT
behavior. If your system cannot support writing bad block markers to OOB,
use the new NAND_BBT_NO_OOB_BBM option (in combination with
NAND_BBT_USE_FLASH and NAND_BBT_NO_OOB).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch renames all MTD functions by adding a "_" prefix:
mtd->erase -> mtd->_erase
mtd->read_oob -> mtd->_read_oob
...
The reason is that we are re-working the MTD API and from now on it is
an error to use MTD function pointers directly - we have a corresponding
API call for every pointer. By adding a leading "_" we achieve the following:
1. Make sure we convert every direct pointer users
2. A leading "_" suggests that this interface is internal and it becomes
less likely that people will use them directly
3. Make sure all the out-of-tree modules stop compiling and the owners
spot the big API change and amend them.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
SPEAr platforms (spear3xx/spear6xx/spear13xx) provide SMI (Serial Memory
Interface) controller to access serial NOR flash. SMI provides a simple
interface for SPI/serial NOR flashes and has certain inbuilt commands
and features to support these flashes easily. It also makes it possible
to map an address range in order to directly access (read/write) the SNOR
over address bus. This patch intends to provide serial nor driver support
for spear platforms which are accessed through SMI.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The description for badblockbits is incorrect. I think someone just made
up a false description on the spot to satisfy some kerneldoc warning.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Because it is useless to call it if the device is opened in R/O mode, and also
harmful: on CFI NOR flash it may block for long time waiting for erase
operations to complete is another partition with a R/W file-system on this
chip.
Artem Bityutskiy: write commit message, amend the patch to match the latest
tree (we use mtd_sync(), not mtd->sync() nowadays).
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
If a header file is making use of BUG, BUG_ON, BUILD_BUG_ON, or any
other BUG variant in a static inline (i.e. not in a #define) then
that header really should be including <linux/bug.h> and not just
expecting it to be implicitly present.
We can make this change risk-free, since if the files using these
headers didn't have exposure to linux/bug.h already, they would have
been causing compile failures/warnings.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
- Fix a regression in 16-bit Atmel NAND flash which was introduced in 3.1
- Fix breakage with MTD suspend caused by the API rework
- Fix a problem with resetting the MX28 BCH module
- A couple of other trivial fixes
* tag 'for-linus-3.3-20120204' of git://git.infradead.org/~dwmw2/mtd-3.3:
Revert "mtd: atmel_nand: optimize read/write buffer functions"
mtd: fix MTD suspend
jffs2: do not initialize variable unnecessarily
mtd: gpmi-nand bugfix: reset the BCH module when it is not MX23
mtd: nand: fix typo in comment
|
|
This patch fixes merge conflict resolution breakage introduced by merge
d3712b9dfcf4 ("Merge tag 'for-linus' of git://github.com/prasad-joshi/logfs_upstream").
The commit changed 'mtd_can_have_bb()' function and made it always
return zero, which is incorrect. Instead, we need it to return whether
the underlying flash device can have bad eraseblocks or not. UBI needs
this information because it affects how it handles the underlying flash.
E.g., if the underlying flash is NOR, it cannot have bad blocks and any
write or erase error is fatal, and all we can do is to switch to R/O
mode. We do not need to reserve a pool of good eraseblocks for bad
eraseblocks handling, and so on.
This patch also removes 'mtd_can_have_bb()' invocations from Logfs to
ensure correct Logfs behavior.
I've tested that with this patch UBI works on top of NOR and NAND
flashes emulated by mtdram and nandsim correspondingly.
This patch is based on patch from Linus Torvalds.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Jörn Engel <joern@logfs.org>
Acked-by: Prasad Joshi <prasadjoshi.linux@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are few important bug fixes for LogFS
* tag 'for-linus' of git://github.com/prasad-joshi/logfs_upstream:
Logfs: Allow NULL block_isbad() methods
logfs: Grow inode in delete path
logfs: Free areas before calling generic_shutdown_super()
logfs: remove useless BUG_ON
MAINTAINERS: Add Prasad Joshi in LogFS maintiners
logfs: Propagate page parameter to __logfs_write_inode
logfs: set superblock shutdown flag after generic sb shutdown
logfs: take write mutex lock during fsync and sync
logfs: Prevent memory corruption
logfs: update page reference count for pined pages
Fix up conflict in fs/logfs/dev_mtd.c due to semantic change in what
"mtd->block_isbad" means in commit f2933e86ad93: "Logfs: Allow NULL
block_isbad() methods" clashing with the abstraction changes in the
commits 7086c19d0742: "mtd: introduce mtd_block_isbad interface" and
d58b27ed58a3: "logfs: do not use 'mtd->block_isbad' directly".
This resolution takes the semantics from commit f2933e86ad93, and just
makes mtd_block_isbad() return zero (false) if the 'block_isbad'
function is NULL. But that also means that now "mtd_can_have_bb()"
always returns 0.
Now, "mtd_block_markbad()" will obviously return an error if the
low-level driver doesn't support bad blocks, so this is somewhat
non-symmetric, but it actually makes sense if a NULL "block_isbad"
function is considered to mean "I assume that all my blocks are always
good".
|
|
Commits 3fe4bae88460869a8e553397cd9057a4ee7ca341 and
079c985e7a6f4ce60f931cebfdd5ee3c3 broke MTD suspend in 2 ways:
1. When the '->suspend' method is not present, we return -EOPNOTSUPP, but
the callers of 'mtd_suspend()' expects 0 instead.
2. Checking of the 'mtd' parameter against NULL has been incorrectly removed
in 'mtd_cls_suspend()'.
This patch fixes the breakages. This has been found, analyzed, reported
and tested by Rafael J. Wysocki <rjw@sisk.pl>.
Note, this patch is not needed in the stable tree because it causes a
regression introduced during the v3.3 merge window.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (53 commits)
ARM: mach-shmobile: specify CHCLR registers on SH7372
dma: shdma: fix runtime PM: clear channel buffers on reset
dma/imx-sdma: save irq flags when use spin_lock in sdma_tx_submit
dmaengine/ste_dma40: clear LNK on channel startup
dmaengine: intel_mid_dma: remove legacy pm interface
ASoC: mxs: correct 'direction' of device_prep_dma_cyclic
dmaengine: intel_mid_dma: error path fix
dmaengine: intel_mid_dma: locking and freeing fixes
mtd: gpmi-nand: move to dma_transfer_direction
mtd: fix compile error for gpmi-nand
mmc: mxs-mmc: fix the dma_transfer_direction migration
dmaengine: add DMA_TRANS_NONE to dma_transfer_direction
dma: mxs-dma: Don't use CLKGATE bits in CTRL0 to disable DMA channels
dma: mxs-dma: make mxs_dma_prep_slave_sg() multi user safe
dma: mxs-dma: Always leave mxs_dma_init() with the clock disabled.
dma: mxs-dma: fix a typo in comment
DMA: PL330: Remove pm_runtime_xxx calls from pl330 probe/remove
video i.MX IPU: Fix display connections
i.MX IPU DMA: Fix wrong burstsize settings
dmaengine/ste_dma40: allow fixed physical channel
...
Fix up conflicts in drivers/dma/{Kconfig,mxs-dma.c,pl330.c}
The conflicts looked pretty trivial, but I'll ask people to verify them.
|
|
Instead, use the new 'mtd_can_have_bb()', or just rely on 'mtd_block_markbad()'
return code, which will be -EOPNOTSUPP if bad blocks are not supported.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch introduces new 'mtd_can_have_bb()' helper function which checks
whether the flash can have bad eraseblocks. Then it changes all the
direct 'mtd->block_isbad' use cases with 'mtd_can_have_bb()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Just call the 'mtd_suspend()' and 'mtd_resume()' - they will do nothing
if the operation is not defined.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Instead, call the corresponding MTD API function which will return
'-EOPNOTSUPP' if the operation is not supported.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch teaches 'mtd_sync()' to do nothing when the MTD driver does
not have the '->sync()' method, which allows us to remove all direct
'mtd->sync' accesses.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch makes the 'mtd_writev()' function more usable and logical. We first
teach it to fall-back to the 'default_mtd_writev()' function if the MTD driver
does not define its own '->writev()' method. Then we make block2mtd and JFFS2
just 'mtd_writev()' instead of 'default_mtd_writev()' function. This means we
can now stop exporting 'default_mtd_writev()' and instead, export
'mtd_writev()'. This is much cleaner and more logical, as well as allows us to
get read of another direct 'mtd->writev' access in JFFS2.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Instead, check the -EOPNOTSUPP return code of 'mtd_lock_user_prot_reg()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Instead, just call 'mtd_write_user_prot_reg()' and check the '-EOPNOTSUPP' return
code.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Instead, call 'mtd_read_*_prot_info()' and check for -EOPNOTSUPP.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Instead, call 'mtd_get_*_prot_info()' and check for '-EOPNOTSUPP'. While
on it, fix the return code from '-EOPNOTSUPP' to '-EINVAL' for the case
when the mode parameter is invalid.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Instead of checking whether 'mtd->read_oob' is defined, just call
'mtd_read_oob()' and handle the '-EOPNOTSUPP' error which will be returned
if the function is undefined.
Additionally, make 'mtd_write_oob()' return '-EOPNOTSUPP' if the function
is undefined.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Instead of checking if 'mtd->panic_write' is defined, call 'mtd_panic_write()'
and check the error code - '-EOPNOTSUPP' will be returned if the function is
not defined.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Remove direct usage of mtd->get_unmapped_area. Instead, just call
'mtd_get_unmapped_area()' which will return -EOPNOTSUPP if the function
is not implemented and test for this error code.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Remove direct usage of the "mtd->point" function pointer. Instead,
test the mtd_point() return code for '-EOPNOTSUPP'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
We are working in the direction of making sure that MTD clients to not
use 'mtd->func' pointers directly. In some places we want to know if
OOB operations are supported by an MTD device. Introduce 'mtd_has_oob()'
helper for these purposes.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
1. Teach 'mtd_write()' function to return '-EROFS' if the write method
is undefined, and remove the corresponding check from
'default_mtd_writev()'.
2. Do not test 'retlen' for NULL - it cannot be NULL.
3. Few minor coding stile clean-ups.
4. Add a kerneldoc comment
Additionally, minor fixes to the kerneldoc comments of the neighbor function.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
