| Age | Commit message (Collapse) | Author |
|---|
|
The chip is an I/O hub used by some Atom boards. Most of those
symbols are used in arch/x86/platform/sta2x11/sta2x11.c (to be
introduced) and in the specific drivers as well.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
northbridge functions
I've received complaints that the numa_node attribute for family
15h model 00-0fh (e.g. Interlagos) northbridge functions shows
-1 instead of the proper node ID.
Correct this with attached quirks (similar to quirks for other
AMD CPU families used in multi-socket systems).
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Frank Arnold <frank.arnold@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/20111202072143.GA31916@alberich.amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
In the OCZ RevoDrive3/zDrive R4 series, the "OCZ SuperScale Storage
Controller" with "Virtualized Controller Architecture 2.0" really seems
to be a Marvell 88SE9485 part, with OCZ firmware/BIOS.
Developed and tested on OCZ RevoDrive3 120GB [PCI 1b85:1021]
Should work on:
- OCZ RevoDrive3 (2x SandForce 2281)
- OCZ RevoDrive3 X2 (4x SandForce 2281)
- OCZ zDrive R4 CM84 (4x SandForce 2281)
- OCZ zDrive R4 CM88 (8x SandForce 2281)
- OCZ zDrive R4 RM84 (4x SandForce 2582)
- OCZ zDrive R4 RM88 (8x SandForce 2582)
All of this because a friend recently bought a OCZ RevoDrive3 and was
bitten by the lack of Linux support.
Notes from testing:
-------------------
- SMART works.
- VPD Device Identification is "OCZ-REVODRIVE3"
- Thin provisioning/TRIM seems to be implemented as WRITE SAME UNMAP,
with deterministic (non-zero) read after TRIM, but I'm not sure if it
works 100% in my testing.
- Some of the tuning in the firmware seems to ensure much better
performance when in a RAID0 setup than using the two devices
seperately.
I have not tested booting from the SSD, because all of this was
developed and tested remotely from the actual hardware.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Thanks-To: Gordon Pritchard <gordp@sfu.ca>
Acked-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
These will be shared between the sfc driver and a PCI quirk.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: use DEFINE_IDR for static initialization
ioat: fix xor_idx_to_desc
Avoid section type conflict in dma/ioat/dma_v3.c
ioat: Adding PCI IDs for IOAT devices on SandyBridge platforms
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (26 commits)
amba pl011: workaround for uart registers lockup
n_gsm: fix the wrong FCS handling
pch_uart: add missing comment about OKI ML7223
pch_uart: Add MSI support
tty: fix "IRQ45: nobody cared"
PTI feature to allow user to name and mark masterchannel request.
0 for o PTI Makefile bug.
tty: serial: samsung.c remove legacy PM code.
SERIAL: SC26xx: Fix link error.
serial: mrst_max3110: initialize waitqueue earlier
mrst_max3110: Change max missing message priority.
tty: s5pv210: Add delay loop on fifo reset function for UART
tty/serial: Fix XSCALE serial ports, e.g. ce4100
serial: bfin_5xx: fix off-by-one with resource size
drivers/tty: use printk_ratelimited() instead of printk_ratelimit()
tty: n_gsm: Added refcount usage to gsm_mux and gsm_dlci structs
tty: n_gsm: Add raw-ip support
tty: n_gsm: expose gsmtty device nodes at ldisc open time
pch_phub: Fix register miss-setting issue
serial: 8250, increase PASS_LIMIT
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (297 commits)
ALSA: asihpi - Replace with snd_ctl_boolean_mono_info()
ALSA: asihpi - HPI version 4.08
ALSA: asihpi - Add volume mute controls
ALSA: asihpi - Control name updates
ALSA: asihpi - Use size_t for sizeof result
ALSA: asihpi - Explicitly include mutex.h
ALSA: asihpi - Add new node and message defines
ALSA: asihpi - Make local function static
ALSA: asihpi - Fix minor typos and spelling
ALSA: asihpi - Remove unused structures, macros and functions
ALSA: asihpi - Remove spurious adapter index check
ALSA: asihpi - Revise snd_pcm_debug_name, get rid of DEBUG_NAME macro
ALSA: asihpi - DSP code loader API now independent of OS
ALSA: asihpi - Remove controlex structs and associated special data transfer code
ALSA: asihpi - Increase request and response buffer sizes
ALSA: asihpi - Give more meaningful name to hpi request message type
ALSA: usb-audio - Add quirk for Roland / BOSS BR-800
ALSA: hda - Remove a superfluous argument of via_auto_init_output()
ALSA: hda - Fix indep-HP path (de-)activation for VT1708* codecs
ALSA: hda - Add documentation for codec-specific mixer controls
...
|
|
Adding to pci_id.h and the device table for ioat.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
And change iSCSI RQ doorbell size from 16B to 64B to match new firmware.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Initialise model-specific DAC and ADC parts.
Add controls for output and mic source selection.
Rename some mixer controls according to ControlNames.txt.
Remove Playback switches for Line-in and IEC958-in - these
were controlling the input mute/unmute which affected
capture too. Use the capture switches to control the
input mute/unmute instead - it's less confusing.
Initialise the WM8775 to invert the left-right clock
to swap the left and right channels of the mic and aux
input.
Signed-off-by: Harry Butterworth <heb1001@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add I/O based support for serial and parallel ports of the following
chips:
Vendor: Moschip (0x9710)
Parts (device IDs)
* 9900 (0x9900)
* 9904 (0x9904
* 9901 (0x9912, also sold as 9912)
* 9922 (0x9922)
On all chips but the 9900, a single port is provided per PCI subdevice
(subvendor-ID 0xA000, subdevice-IDs 0x1000 for serial, 0x2000 for
parallel with proper class codes). In cascading configurations, the
9900 provides two devices per subdevice, with subvendor-ID 0xA000 and
subdevice-IDs 0x30ps where p is the number of parallel ports and s the
number of serial ports.
Basic testing was only done on the serial part of a 9912 to the point
where it can be used for a serial kernel console, and advanced features
are completely untested. It is possible to reduce functionality of the
chips by adding a configuration EEPROM, and the datasheet [1] is
inconsistent w.r.t subdevices in the 4s+2s1p and 2s1p+4s
configurations. The subdevice-ID 0x3012 should likely read 0x3011 with
a serial port in function 3, which would be consistent with the BAR
layouts. For now, the drivers ignore subdevices with ID 0x1000 and no
class code.
The parallel ports are integrated in parport_serial even for purely
parallel parts to reduce the footprint of the patch.
[1] http://www.moschip.com/data/products/MCS9900/MCS9900_Datasheet.pdf
Signed-off-by: Nicos Gollan <gtdev@spearhead.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This adds the PCI ID for the xHCI (USB 3.0) host controller in the Intel
Panther Point chipset. It will be used by both the EHCI and xHCI driver
in the following patches.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
PCI: Don't use dmi_name_in_vendors in quirk
PCI: remove unused AER functions
PCI/sysfs: move bus cpuaffinity to class dev_attrs
PCI: add rescan to /sys/.../pci_bus/.../
PCI: update bridge resources to get more big ranges when allocating space (again)
KVM: Use pci_store/load_saved_state() around VM device usage
PCI: Add interfaces to store and load the device saved state
PCI: Track the size of each saved capability data area
PCI/e1000e: Add and use pci_disable_link_state_locked()
x86/PCI: derive pcibios_last_bus from ACPI MCFG
PCI: add latency tolerance reporting enable/disable support
PCI: add OBFF enable/disable support
PCI: add ID-based ordering enable/disable support
PCI hotplug: acpiphp: assume device is in state D0 after powering on a slot.
PCI: Set PCIE maxpayload for card during hotplug insertion
PCI/ACPI: Report _OSC control mask returned on failure to get control
x86/PCI: irq and pci_ids patch for Intel Panther Point DeviceIDs
PCI: handle positive error codes
PCI: check pci_vpd_pci22_wait() return
PCI: Use ICH6_GPIO_EN in ich6_lpc_acpi_gpio
...
Fix up trivial conflicts in include/linux/pci_ids.h: commit a6e5e2be4461
moved the intel SMBUS ID definitons to the i2c-i801.c driver.
|
|
The old IDE cmd64x checks the status of the CNTRL register to see if
the ports are enabled before probing them. pata_cmd64x doesn't do
this, which causes a HPMC on parisc when it tries to poke at the
secondary port because apparently the BAR isn't wired up (and a
non-responding piece of memory causes a HPMC).
Fix this by porting the CNTRL register port detection logic from IDE
cmd64x. In addition, following converns from Alan Cox, add a check to
see if a mobility electronics bridge is the immediate parent and forgo
the check if it is (prevents problems on hotplug controllers).
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
This patch adds the LPC Controller DeviceIDs for the Intel Panther Point PCH.
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Move the SMBus device ID definitions of recent devices from pci_ids.h
to the i2c-i801.c driver file. They don't have to be shared, as they
are clearly identified and only used in this driver. In the future,
such IDs will go to i2c-i801 directly. This will make adding support
for new devices much faster and easier, as it will avoid cross-
subsystem patch sets and merge conflicts.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Seth Heasley <seth.heasley@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
With increasing number of PCI function ids, add the PCI function
id in the define name instead of its symbolic name in the BKDG
for more clarity. This renames function 4 define.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
LKML-Reference: <20110330183447.GA3668@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: label: remove #include of ACPI header to avoid warnings
PCI: label: Fix compilation error when CONFIG_ACPI is unset
PCI: pre-allocate additional resources to devices only after successful allocation of essential resources.
PCI: introduce reset_resource()
PCI: data structure agnostic free list function
PCI: refactor io size calculation code
PCI: do not create quirk I/O regions below PCIBIOS_MIN_IO for ICH
PCI hotplug: acpiphp: set current_state to D0 in register_slot
PCI: Export ACPI _DSM provided firmware instance number and string name to sysfs
PCI: add more checking to ICH region quirks
PCI: aer-inject: Override PCIe AER Mask Registers
PCI: fix tlan build when CONFIG_PCI is not enabled
PCI: remove quirk for pre-production systems
PCI: Avoid potential NULL pointer dereference in pci_scan_bridge
PCI/lpc: irq and pci_ids patch for Intel DH89xxCC DeviceIDs
PCI: sysfs: Fix failure path for addition of "vpd" attribute
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (170 commits)
[SCSI] scsi_dh_rdac: Add MD36xxf into device list
[SCSI] scsi_debug: add consecutive medium errors
[SCSI] libsas: fix ata list corruption issue
[SCSI] hpsa: export resettable host attribute
[SCSI] hpsa: move device attributes to avoid forward declarations
[SCSI] scsi_debug: Logical Block Provisioning (SBC3r26)
[SCSI] sd: Logical Block Provisioning update
[SCSI] Include protection operation in SCSI command trace
[SCSI] hpsa: fix incorrect PCI IDs and add two new ones (2nd try)
[SCSI] target: Fix volume size misreporting for volumes > 2TB
[SCSI] bnx2fc: Broadcom FCoE offload driver
[SCSI] fcoe: fix broken fcoe interface reset
[SCSI] fcoe: precedence bug in fcoe_filter_frames()
[SCSI] libfcoe: Remove stale fcoe-netdev entries
[SCSI] libfcoe: Move FCOE_MTU definition from fcoe.h to libfcoe.h
[SCSI] libfc: introduce __fc_fill_fc_hdr that accepts fc_hdr as an argument
[SCSI] fcoe, libfc: initialize EM anchors list and then update npiv EMs
[SCSI] Revert "[SCSI] libfc: fix exchange being deleted when the abort itself is timed out"
[SCSI] libfc: Fixing a memory leak when destroying an interface
[SCSI] megaraid_sas: Version and Changelog update
...
Fix up trivial conflicts due to whitespace differences in
drivers/scsi/libsas/{sas_ata.c,sas_scsi_host.c}
|
|
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (38 commits)
amd64_edac: Fix decode_syndrome types
amd64_edac: Fix DCT argument type
amd64_edac: Fix ranges signedness
amd64_edac: Drop local variable
amd64_edac: Fix PCI config addressing types
amd64_edac: Fix DRAM base macros
amd64_edac: Fix node id signedness
amd64_edac: Drop redundant declarations
amd64_edac: Enable driver on F15h
amd64_edac: Adjust ECC symbol size to F15h
amd64_edac: Simplify scrubrate setting
PCI: Rename CPU PCI id define
amd64_edac: Improve DRAM address mapping
amd64_edac: Sanitize ->read_dram_ctl_register
amd64_edac: Adjust sys_addr to chip select conversion routine to F15h
amd64_edac: Beef up early exit reporting
amd64_edac: Revamp online spare handling
amd64_edac: Fix channel interleave removal
amd64_edac: Correct node interleaving removal
amd64_edac: Add support for interleaved region swapping
...
Fix up trivial conflict in include/linux/pci_ids.h due to
AMD_15H_NB_MISC being renamed as AMD_15H_NB_F3 next to the new
AMD_15H_NB_LINK entry.
|
|
With increasing number of PCI function ids, add the PCI function id
in the define name instead of its symbolic name in the BKDG for more
clarity.
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
|
|
Moved all PCI_DEVICE_ID_NX2_57712(E) definitions to pci_ids.h
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch adds the LPC Controller DeviceIDs for the Intel DH89xxCC PCH.
The code for capturing ranges of LPC Controller DeviceIDs has also been updated.
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
"Link Control" devices (NB function 4) will be used by L3 cache
partitioning on family 0x15.
Signed-off-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
Cc: <andreas.herrmann3@amd.com>
LKML-Reference: <1295881543-572552-4-git-send-email-hans.rosenfeld@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/PM: Report wakeup events before resuming devices
PCI/PM: Use pm_wakeup_event() directly for reporting wakeup events
PCI: sysfs: Update ROM to include default owner write access
x86/PCI: make Broadcom CNB20LE driver EMBEDDED and EXPERIMENTAL
x86/PCI: don't use native Broadcom CNB20LE driver when ACPI is available
PCI/ACPI: Request _OSC control once for each root bridge (v3)
PCI: enable pci=bfsort by default on future Dell systems
PCI/PCIe: Clear Root PME Status bits early during system resume
PCI: pci-stub: ignore zero-length id parameters
x86/PCI: irq and pci_ids patch for Intel Patsburg
PCI: Skip id checking if no id is passed
PCI: fix __pci_device_probe kernel-doc warning
PCI: make pci_restore_state return void
PCI: Disable ASPM if BIOS asks us to
PCI: Add mask bit definition for MSI-X table
PCI: MSI: Move MSI-X entry definition to pci_regs.h
Fix up trivial conflicts in drivers/net/{skge.c,sky2.c} that had in the
meantime been converted to not use legacy PCI power management, and thus
no longer use pci_restore_state() at all (and that caused trivial
conflicts with the "make pci_restore_state return void" patch)
|
|
Signed-off-by: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix Moorestown VRTC fixmap placement
x86/gpio: Implement x86 gpio_to_irq convert function
x86, UV: Fix APICID shift for Westmere processors
x86: Use PCI method for enabling AMD extended config space before MSR method
x86: tsc: Prevent delayed init if initial tsc calibration failed
x86, lapic-timer: Increase the max_delta to 31 bits
x86: Fix sparse non-ANSI function warnings in smpboot.c
x86, numa: Fix CONFIG_DEBUG_PER_CPU_MAPS without NUMA emulation
x86, AMD, PCI: Add AMD northbridge PCI device id for CPU families 12h and 14h
x86, numa: Fix cpu to node mapping for sparse node ids
x86, numa: Fake node-to-cpumask for NUMA emulation
x86, numa: Fake apicid and pxm mappings for NUMA emulation
x86, numa: Avoid compiling NUMA emulation functions without CONFIG_NUMA_EMU
x86, numa: Reduce minimum fake node size to 32M
Fix up trivial conflict in arch/x86/kernel/apic/x2apic_uv_x.c
|
|
JMicron 388 SD/MMC combo controller supports the 1.8V low-voltage for
SD, but MMC doesn't work with the low-voltage, resulting in an error
at probing.
This patch adds the support for multiple voltage mask per device type,
so that SD works with 1.8V while MMC forces 3.3V. Here new ocr_avail_*
fields for each device are introduced, so that the actual OCR mask is
switched dynamically.
Also, the restriction of low-voltage in core/sd.c is removed when the
bit is allowed explicitly via ocr_avail_sd mask.
This patch was rewritten from scratch based on Aries' original code.
Signed-off-by: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This patch disables the broken ADMA on selected O2Micro devices.
Signed-off-by: Jennifer Li <Jennifer.li@o2micro.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This patch adds the PCI northbridge device id for AMD CPU
families 12h and 14h. Both families have implemented the same
PCI northbridge device.
There are some future use cases that use this PCI device and
we would like to clarify its naming.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Cc: xen-devel@lists.xensource.com <xen-devel@lists.xensource.com>
Cc: Keir Fraser <keir@xen.org>
Cc: Jan Beulich <JBeulich@novell.com>
LKML-Reference: <20110106165107.GL4739@erda.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This patch adds an additional LPC Controller DeviceID for the Intel
Patsburg PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
af_unix: limit recursion level
pch_gbe driver: The wrong of initializer entry
pch_gbe dreiver: chang author
ucc_geth: fix ucc halt problem in half duplex mode
inet: Fix __inet_inherit_port() to correctly increment bsockets and num_owners
ehea: Add some info messages and fix an issue
hso: fix disable_net
NET: wan/x25_asy, move lapb_unregister to x25_asy_close_tty
cxgb4vf: fix setting unicast/multicast addresses ...
net, ppp: Report correct error code if unit allocation failed
DECnet: don't leak uninitialized stack byte
au1000_eth: fix invalid address accessing the MAC enable register
dccp: fix error in updating the GAR
tcp: restrict net.ipv4.tcp_adv_win_scale (#20312)
netns: Don't leak others' openreq-s in proc
Net: ceph: Makefile: Remove unnessary code
vhost/net: fix rcu check usage
econet: fix CVE-2010-3848
econet: fix CVE-2010-3850
econet: disallow NULL remote addr for sendmsg(), fixes CVE-2010-3849
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Add new vendor for Broadcom 4318.
Signed-off-by: Daniel Klaffenbach <danielklaffenbach@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
SDHC2 is newly added in C0 stepping of Langwell. Without the Moorestown
specific quirk, the default pci_probe will be called and crash the kernel.
This patch unblocks the crash problem on C0 by using the same probing
function as HC1, which limits the number of slots to one.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add support for the Intel Patsburg PCH SMBus Controller.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
x86: allocate space within a region top-down
x86: update iomem_resource end based on CPU physical address capabilities
x86/PCI: allocate space from the end of a region, not the beginning
PCI: allocate bus resources from the top down
resources: support allocating space within a region from the top down
resources: handle overflow when aligning start of available area
resources: ensure callback doesn't allocate outside available space
resources: factor out resource_clip() to simplify find_resource()
resources: add a default alignf to simplify find_resource()
x86/PCI: MMCONFIG: fix region end calculation
PCI: Add support for polling PME state on suspended legacy PCI devices
PCI: Export some PCI PM functionality
PCI: fix message typo
PCI: log vendor/device ID always
PCI: update Intel chipset names and defines
PCI: use new ccflags variable in Makefile
PCI: add PCI_MSIX_TABLE/PBA defines
PCI: add PCI vendor id for STmicroelectronics
x86/PCI: irq and pci_ids patch for Intel Patsburg DeviceIDs
PCI: OLPC: Only enable PCI configuration type override on XO-1
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (66 commits)
mmc: add new sdhci-pxa driver for Marvell SoCs
mmc: make number of mmcblk minors configurable
mmc_spi: Recover from CRC errors for r/w operation over SPI.
mmc: sdhci-pltfm: add -pltfm driver for imx35/51
mmc: sdhci-of-esdhc: factor out common stuff
mmc: sdhci_pltfm: pass more data on custom init call
mmc: sdhci: introduce get_ro private write-protect hook
mmc: sdhci-pltfm: move .h file into appropriate subdir
mmc: sdhci-pltfm: Add structure for host-specific data
mmc: fix cb710 kconfig dependency warning
mmc: cb710: remove debugging printk (info duplicated from mmc-core)
mmc: cb710: clear irq handler on init() error path
mmc: cb710: remove unnecessary msleep()
mmc: cb710: implement get_cd() callback
mmc: cb710: partially demystify clock selection
mmc: add a file to debugfs for changing host clock at runtime
mmc: sdhci: allow for eMMC 74 clock generation by controller
mmc: sdhci: highspeed: check for mmc as well as sd cards
mmc: sdhci: Add Moorestown device support
mmc: sdhci: Intel Medfield support
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (110 commits)
sh: i2c-sh7760: Replase from ctrl_* to __raw_*
sh: clkfwk: Shuffle around to match the intc split up.
sh: clkfwk: modify for_each_frequency end condition
sh: fix clk_get() error handling
sh: clkfwk: Fix fault in frequency iterator.
sh: clkfwk: Add a helper for rate rounding by divisor ranges.
sh: clkfwk: Abstract rate rounding helper.
sh: clkfwk: support clock remapping.
sh: pci: Convert to upper/lower_32_bits() helpers.
sh: mach-sdk7786: Add support for the FPGA SRAM.
sh: Provide a generic SRAM pool for tiny memories.
sh: pci: Support secondary FPGA-driven PCIe clocks on SDK7786.
sh: pci: Support slot 4 routing on SDK7786.
sh: Fix up PMB locking.
sh: mach-sdk7786: Add support for fpga gpios.
sh: use pr_fmt for clock framework, too.
sh: remove name and id from struct clk
sh: free-without-alloc fix for sh_mobile_lcdcfb
sh: perf: Set up perf_max_events.
sh: perf: Support SH-X3 hardware counters.
...
Fix up trivial conflicts (perf_max_events got removed) in arch/sh/kernel/perf_event.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/edac
* 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/edac: (25 commits)
i7300_edac: Properly initialize per-csrow memory size
V4L/DVB: i7300_edac: better initialize page counts
MAINTAINERS: Add maintainer for i7300-edac driver
i7300-edac: CodingStyle cleanup
i7300_edac: Improve comments
i7300_edac: Cleanup: reorganize the file contents
i7300_edac: Properly detect channel on CE errors
i7300_edac: enrich FBD error info for corrected errors
i7300_edac: enrich FBD error info for fatal errors
i7300_edac: pre-allocate a buffer used to prepare err messages
i7300_edac: Fix MTR x4/x8 detection logic
i7300_edac: Make the debug messages coherent with the others
i7300_edac: Cleanup: remove get_error_info logic
i7300_edac: Add a code to cleanup error registers
i7300_edac: Add support for reporting FBD errors
i7300_edac: Properly detect the type of error correction
i7300_edac: Detect if the device is on single mode
i7300_edac: Adds detection for enhanced scrub mode on x8
i7300_edac: Clear the error bit after reading
i7300_edac: Add error detection code for global errors
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
|
|
Basic support for the Intel Medfield devices
Give them their own quirks as we will need to update this later.
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
* 'for-2.6.37/drivers' of git://git.kernel.dk/linux-2.6-block: (95 commits)
cciss: fix PCI IDs for new Smart Array controllers
drbd: add race-breaker to drbd_go_diskless
drbd: use dynamic_dev_dbg to optionally log uuid changes
dynamic_debug.h: Fix dynamic_dev_dbg() macro if CONFIG_DYNAMIC_DEBUG not set
drbd: cleanup: change "<= 0" to "== 0"
drbd: relax the grace period of the md_sync timer again
drbd: add some more explicit drbd_md_sync
drbd: drop wrong debug asserts, fix recently introduced race
drbd: cleanup useless leftover warn/error printk's
drbd: add explicit drbd_md_sync to drbd_resync_finished
drbd: Do not log an ASSERT for P_OV_REQUEST packets while C_CONNECTED
drbd: fix for possible deadlock on IO error during resync
drbd: fix unlikely access after free and list corruption
drbd: fix for spurious fullsync (uuids rotated too fast)
drbd: allow for explicit resync-finished notifications
drbd: preparation commit, using full state in receive_state()
drbd: drbd_send_ack_dp must not rely on header information
drbd: Fix regression in recv_bm_rle_bits (compressed bitmap)
drbd: Fixed a stupid copy and paste error
drbd: Allow larger values for c-fill-target.
...
Fix up trivial conflict in drivers/block/ataflop.c due to BKL removal
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (71 commits)
powerpc/44x: Update ppc44x_defconfig
powerpc/watchdog: Make default timeout for Book-E watchdog a Kconfig option
fsl_rio: Add comments for sRIO registers.
powerpc/fsl-booke: Add e55xx (64-bit) smp defconfig
powerpc/fsl-booke: Add p5020 DS board support
powerpc/fsl-booke64: Use TLB CAMs to cover linear mapping on FSL 64-bit chips
powerpc/fsl-booke: Add support for FSL Arch v1.0 MMU in setup_page_sizes
powerpc/fsl-booke: Add support for FSL 64-bit e5500 core
powerpc/85xx: add cache-sram support
powerpc/85xx: add ngPIXIS FPGA device tree node to the P1022DS board
powerpc: Fix compile error with paca code on ppc64e
powerpc/fsl-booke: Add p3041 DS board support
oprofile/fsl emb: Don't set MSR[PMM] until after clearing the interrupt.
powerpc/fsl-booke: Add PCI device ids for P2040/P3041/P5010/P5020 QoirQ chips
powerpc/mpc8xxx_gpio: Add support for 'qoriq-gpio' controllers
powerpc/fsl_booke: Add support to boot from core other than 0
powerpc/p1022: Add probing for individual DMA channels
powerpc/fsl_soc: Search all global-utilities nodes for rstccr
powerpc: Fix invalid page flags in create TLB CAM path for PTE_64BIT
powerpc/mpc83xx: Support for MPC8308 P1M board
...
Fix up conflict with the generic irq_work changes in arch/powerpc/kernel/time.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-amd-nb-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, amd_nb: Enable GART support for AMD family 0x15 CPUs
x86, amd: Use compute unit information to determine thread siblings
x86, amd: Extract compute unit information for AMD CPUs
x86, amd: Add support for CPUID topology extension of AMD CPUs
x86, nmi: Support NMI watchdog on newer AMD CPU families
x86, mtrr: Assume SYS_CFG[Tom2ForceMemTypeWB] exists on all future AMD CPUs
x86, k8: Rename k8.[ch] to amd_nb.[ch] and CONFIG_K8_NB to CONFIG_AMD_NB
x86, k8-gart: Decouple handling of garts and northbridges
x86, cacheinfo: Fix dependency of AMD L3 CID
x86, kvm: add new AMD SVM feature bits
x86, cpu: Fix allowed CPUID bits for KVM guests
x86, cpu: Update AMD CPUID feature bits
x86, cpu: Fix renamed, not-yet-shipping AMD CPUID feature bit
x86, AMD: Remove needless CPU family check (for L3 cache info)
x86, tsc: Remove CPU frequency calibration on AMD
|
|
cciss: fix PCI IDs for new controllers
This patch fixes the botched up PCI IDs of new controllers. Please consider
this patch for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
