| Age | Commit message (Collapse) | Author |
|---|
|
This patch introduces device tree support to the isp1704 charger driver.
Adding support involved moving the handling of the enable GPIO from board
code into the driver.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
This patch removing set_mode_hook function from board data and replacing
it with new string variable of notifier power supply device. After this
change it is possible to add DT support because driver does not need
specific board function anymore. Only static data and name of power supply
device is required.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
Charger-manager can parse charger_desc data from devicetree which is used
to register charger manager.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
Charger-manager driver used to check battery temperature through the
callback function passed by platform data. Unfortunatley, without that
pre-defined callback function, charger-manager can't get battery's
temperature at all. Also passing callback function through platform data
ruins DT support for charger-manager.
This patch mondifies charger-manager driver to get temperature of battery
without pre-defined callback function. Now, charger-manager can use either
of battery thermometer in fuel-gauge and ouside of battery. It uses
thermal framework interface for outer thermometer if thermal fw is
enabled. Otherwise, it tries to use fuel-gauge's through the power supply
interface.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
Adds support for the bq24735 charger chipset. The bq24735 is a
high-efficiency, synchronous battery charger.
It allows control of the charging current, input current, and the charger
voltage DAC's through SMBus.
Signed-off-by: Darbha Sriharsha <dsriharsha@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Thanks-to: Stephen Warren <swarren@wwwdotorg.org>
Thanks-to: Thierry Reding <thierry.reding@gmail.com>
Thanks-to: Manish Badarkhe <badarkhe.manish@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
This driver is used and tested on gta04 phone. It's using twl4030_madc
(similar to rx51 existing driver). Driver also implement charging and
discharging calibration data so user can define ranges and level.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Lukas Märdian <lukas@goldelico.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
Add driver support for the Texas Instruments BQ24190 battery charger.
Some of the information provided by the device is about the charger and
other information is about the battery so create two power_supply objects
(one for each) and provide the appropriate information for each one.
The device has many fields that go beyond what is reasonable to report or
modify using the existing 'POWER_SUPPLY_PROP_*' properties so the driver
exports the register fields via sysfs. They are prefixed by 'f_' (for
'field') to make it easier to distinguish between a register field and a
"normal" sysfs file exported by the power_supply infrastructure.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
SmartReflex driver interface is natively divided to two parts:
- external SmartReflex interface
- interface between SmartReflex driver and SmartReflex Class
Functions which belong to AVS class interface can use
struct omap_sr* instead of struct voltatedomain*, to provide a
direct connection between SR driver and SR class. This allows
us to optimize and not do additional lookups where none is
required.
sr_enable() and sr_disable() are interface functions between
SR driver and SR class. They are typically used by Class driver
to enable/disable SmartReflex hardware module.
Now they take struct omap_sr* as input parameter.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
SmartReflex driver interface is natively divided to two parts:
- external SmartReflex interface
- interface between SmartReflex driver and SmartReflex Class
Functions which belong to AVS class interface can use
struct omap_sr* instead of struct voltatedomain*, to provide a
direct connection between SR driver and SR class. This allows
us to optimize and not do additional lookups where none is
required.
sr_configure_minmax() is interface function between SR driver
and SR class. It is typically used by Class driver to
configure MINMAXAVG module inside SmartReflex module.
Now it takes struct omap_sr* as input parameter.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
SmartReflex driver interface is natively divided to two parts:
- external SmartReflex interface
- interface between SmartReflex driver and SmartReflex Class
Functions which belong to AVS class interface can use
struct omap_sr* instead of struct voltatedomain*, to provide a
direct connection between SR driver and SR class. This allows
us to optimize and not do additional lookups where none is
required.
sr_disable_errgen() and sr_configure_errgen() are interface
functions between SR driver and SR class. They are typically
used by Class driver to configure error generator module during
SmartReflex enable/disable sequence.
Now they take struct omap_sr* as input parameter.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
This patch exports the thermistor resistance-to-temperature tables, so
that the hwmon driver can access them, and also adds the corresponding
table size variables.
Signed-off-by: Hongbo Zhang <hongbo.zhang@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
* Renamed mode BQ2415X_MODE_NONE to BQ2415X_MODE_OFF because this mode
turning chaging completly off
* Added new mode BQ2415X_MODE_NONE which enable charging with maximal
current limit 100mA (this is minimal safe value for bq2415x chips)
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
|
|
Pull battery subsystem updates from Anton Vorontsov:
"Highlights:
- Two new drivers from Pali Rohár and N900 hackers: rx51_battery and
bq2415x_charger. The drivers are a part of a solution to replace
the proprietary Nokia BME stack
- Power supply core now registers devices with a thermal cooling
subsystem, so we can now automatically throttle charging. Thanks
to Ramakrishna Pallala!
- Device tree support for ab8500 and max8925_power drivers
- Random fixups and enhancements for a bunch of drivers."
* tag 'for-v3.8-merged' of git://git.infradead.org/battery-2.6: (22 commits)
max8925_power: Add support for device-tree initialization
ab8500: Add devicetree support for chargalg
ab8500: Add devicetree support for charger
ab8500: Add devicetree support for btemp
ab8500: Add devicetree support for fuelgauge
twl4030_charger: Change TWL4030_MODULE_* ids to TWL_MODULE_*
jz4740-battery: Use devm_request_and_ioremap
jz4740-battery: Use devm_kzalloc
bq27x00_battery: Fixup nominal available capacity reporting
bq2415x_charger: Fix style issues
bq2415x_charger: Add Kconfig/Makefile entries
power_supply: Add bq2415x charger driver
power_supply: Add new Nokia RX-51 (N900) power supply battery driver
max17042_battery: Fix missing verify_model_lock() return value check
ds2782_battery: Fix signedness bug in ds278x_read_reg16()
lp8788-charger: Fix ADC channel names
lp8788-charger: Fix wrong ADC conversion
lp8788-charger: Use consumer device name on setting IIO channels
power_supply: Register power supply for thermal cooling device
power_supply: Add support for CHARGE_CONTROL_* attributes
...
|
|
I hate doing these style fixups myself, but I also hate inconsitent code.
Normally I just ask to resubmit the patch with the issues fixed, but N900
is special: I have a selfish interest in it. :)
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
The bq2415x charger driver is needed for example on Nokia N900 for
charging battery. Driver is part of open source project to replace
proprietary battery management.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
Remove the device dependent code (ex. cpu_is_xxx()) and settings
from the driver code and instead pass them via the platform
data. This allows a clean separation of the driver code and the platform
code, as required by the move of the platform header files to
include/linux/platform_data.
Note about the smartreflex functional clocks: the smartreflex fclks
are derived from sys_clk and have the same name as the main_clk from
the hwmod entry, in order for the SmartReflex driver to request the
fclk (using clk_get(dev, "fck")).
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Pull battery updates from Anton Vorontsov:
"1. New drivers:
- Marvell 88pm860x charger and battery drivers;
- Texas Instruments LP8788 charger driver;
2. Two new power supply properties: whether a battery is authentic,
and chargers' maximal currents and voltages;
3. A lot of TI LP8727 Charger cleanups;
4. New features for Charger Manager, mainly now we can disable
specific regulators;
5. Random fixes and cleanups for other drivers."
Fix up trivial conflicts in <linux/mfd/88pm860x.h>
* tag 'for-v3.7' of git://git.infradead.org/battery-2.6: (52 commits)
pda_power: Remove ac_draw_failed goto and label
charger-manager: Add support sysfs entry for charger
charger-manager: Support limit of maximum possible
charger-manager: Check fully charged state of battery periodically
lp8727_charger: More pure cosmetic improvements
lp8727_charger: Fix checkpatch warning
lp8727_charger: Add description in the private data
lp8727_charger: Fix a typo - chg_parm to chg_param
lp8727_charger: Make some cosmetic changes in lp8727_delayed_func()
lp8727_charger: Clean up lp8727_charger_changed()
lp8727_charger: Return if the battery is discharging
lp8727_charger: Make lp8727_charger_get_propery() simpler
lp8727_charger: Make lp8727_ctrl_switch() inline
lp8727_charger: Make lp8727_init_device() shorter
lp8727_charger: Clean up lp8727_is_charger_attached()
lp8727_charger: Use specific definition
lp8727_charger: Clean up lp8727 definitions
lp8727_charger: Use the definition rather than enum
lp8727_charger: Fix code for getting battery temp
lp8727_charger: Clear interrrupts at inital time
...
|
|
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
|
|
Driver to allow use of the ADC drivers supported by the IIO
subsystem for battery status monitoring. Connecting this
driver to the relevant IIO device requires registration of
the appropriate iio_map structure array by the IIO device
driver (usually from platform data). If specified the driver
will also make use of a gpio to provide interrupt driven
notification that the battery is fully charged.
In last version:
Addressed concerns raised by lars:
a. made the adc_bat per device.
b. get the IIO channel using hardcoded channel names.
c. Minor issues related to gpio_is_valid and some code
refactoring.
In V1:
Addressed concerns raised by Anton:
a. changed the struct name to gab(generic adc battery).
b. Added some functions to neaten the code.
c. Some minor coding guidelines changes.
d. Used the latest function introduce by lars:
iio_read_channel_processed to streamline the code.
In V2:
Addressed concerns by lars:
a. No need of allocating memory for channels.Make it array.
b. Code restructring, coding style and following kernel guidelines changes
suggested by him.
In V3:
Addressed conerns by Anton:
a. Added the copyright.
b. Coding guidelines changes suggested by him.
c. Added Makefile and Kconfig
Signed-off-by: anish kumar <anish198519851985@gmail.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch add support sysfs entry for each charger(regulator).
Charger-manager use one or more chargers for charging battery but some
charger isn't necessary on specific scenario. So, if some charger isn't
needed, can disable specific charger through 'externally_control' entry
while system is on state and confirm the information(name, state) of
charger.
The list of added sysfs entry
- /sys/class/power_supply/battery/chargers/charger.[index]/name
show name of charger(regulator)
- /sys/class/power_supply/battery/chargers/charger.[index]/state
show either enabled or disabled state of charger
- /sys/class/power_supply/battery/chargers/charger.[index]/externally_control
If 'externally_control' of specific charger is 1, Charger-manager cannot
enable regulator for charging when charger cable is attached and charger
must be maintained with disabled state. If 'externally_control' is zero,
Charger-manager usually can control to enable/disable regulator.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
This patch check maximum possible duration of charging/discharging.
If whole charging duration exceed 'desc->charging_max_duration_ms', cm
stop charging to prevent overcharge/overheat. And if discharging duration
exceed, charger cable is attached, after full-batt, cm start charging to
maintain fully charged state for battery.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
This patch check periodically fully charged state of battery to protect
overcharge and overheat. If battery is fully charged, stop charging and
check droped voltage with 'fullbatt_vchkdrop_ms' period. When voltage of
battery is more droped than 'fullbatt_vchkdrop_uV' voltage,
charger-manager will restart charging for battery.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the omap include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Benoît Cousson" <b-cousson@ti.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Jean Pihet <j-pihet@ti.com>
Cc: J Keerthy <j-keerthy@ti.com>
Cc: linux-omap@vger.kernel.org
|
|
The comment says that charger_regulators is an array of
regulator_bulk_data, which is not true, since it's actually a pointer
to 'struct charger_regulator'.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
This patch remove unnecessary variable(cm->fullbatt_vchk_uV) by using
'desc->fullbatt_uV' field directly in fullbatt_handler() function
to check the state of battery.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
Pull battery updates from Anton Vorontsov:
"The tag contains just a few battery-related changes for v3.6. It's is
all pretty straightforward, except one thing.
One of our patches added thermal support for power supply class, but
thermal/ subsystem changed under our feet. We (well, Stephen, that
is) caught the issue and it was decided[1] that I'd just delay the
battery pull request, and then will fix it up by merging upstream back
into battery tree at the specific commit.
That's not all though: another[2] small fixup for thermal subsystem
was needed to get rid of a warning in power supply subsystem (the
warning was not drivers/power's "fault", the thermal registration
function just needed a proper const annotation, which is also done by
a small commit on top of the merge.
So, to sum this up:
- The 'master' branch of the battery tree was in the -next tree for
weeks, was never rebased, altered etc. It should be all OK;
- Although, for-v3.6 tag contains the 'master' branch + merge + the
warning fix.
[1] http://lkml.org/lkml/2012/6/19/23
[2] http://lkml.org/lkml/2012/6/18/28"
* tag 'for-v3.6' of git://git.infradead.org/battery-2.6: (23 commits)
thermal: Constify 'type' argument for the registration routine
olpc-battery: update CHARGE_FULL_DESIGN property for BYD LiFe batteries
olpc-battery: Add VOLTAGE_MAX_DESIGN property
charger-manager: Fix build break related to EXTCON
lp8727_charger: Move header file into platform_data directory
power_supply: Add min/max alert properties for CAPACITY, TEMP, TEMP_AMBIENT
bq27x00_battery: Add support for BQ27425 chip
charger-manager: Set current limit of regulator for over current protection
charger-manager: Use EXTCON Subsystem to detect charger cables for charging
test_power: Add VOLTAGE_NOW and BATTERY_TEMP properties
test_power: Add support for USB AC source
gpio-charger: Use cansleep version of gpio_set_value
bq27x00_battery: Add support for power average and health properties
sbs-battery: Don't trigger false supply_changed event
twl4030_charger: Allow charger to control the regulator that feeds it
twl4030_charger: Add backup-battery charging
twl4030_charger: Fix some typos
max17042_battery: Support CHARGE_COUNTER power supply attribute
smb347-charger: Add constant charge and current properties
power_supply: Add constant charge_current and charge_voltage properties
...
|
|
This patch support the protection of host device from over current.
The Charger-manager set proper current limit of charger(regulator) for
charging according to type of charger cable when external connector
is attached.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
This patch support that charger-manager use EXTCON(External Connector)
Subsystem to detect the state of charger cables for enabling or disabling
charger(regulator) and select the charger cable for charging among
a number of external cable according to policy of H/W board.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into devel-driver
|
|
Add a Kconfig menu (POWER_AVS) and rename the Kconfig options
for the OMAP SmartReflex implementation:
CONFIG_OMAP_SMARTREFLEX renames to CONFIG_POWER_AVS_OMAP
CONFIG_OMAP_SMARTREFLEX_CLASS3 renames to CONFIG_POWER_AVS_OMAP_CLASS3
This change makes the SmartReflex implementation ready for the move
to drivers/.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
The SmartReflex driver incorrectly treats some per-OPP data as data
common to all OPPs (e.g., ERRMINLIMIT). Move this data into a per-OPP
data structure.
Furthermore, in order to make the SmartReflex implementation ready for
the move to drivers/, remove the dependency from the SR driver code
to the voltage layer by querying the data tables only from the SR device
init code.
Based on Paul's original code for the SmartReflex driver conversion.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Now that omap_test_timeout is only accessible from mach-omap2/,
introduce a similar function for SR.
This change makes the SmartReflex implementation ready for the move
to drivers/.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
domains.
Associate a name with each SmartReflex instance from the hwmod data,
rather than attempting to reuse the name of a voltage domain. The name
from hwmod better reflects the smartreflex integration in the system.
Also have the name passed to the drivers using pdata, which helps to remove
any dependencies on SoC-specific structures.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Convert SmartReflex "class" functions to take a struct omap_sr *, rather than
a struct voltagedomain *. SmartReflex code should be driver code and not
tightly coupled to OMAP subarchitecture-specific structures.
Based on Paul's original code for the SmartReflex driver conversion.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Move the smartreflex header file
(arch/arm/mach-omap2/smartreflex.h) in a new header file
include/linux/power/smartreflex.h.
This change makes the SmartReflex implementation ready for the move
to drivers/.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
max17047 is improved version of max17042 chip. It has few HW bug
fixes with minor changes in register set.
max17050 is same as max17047 chip except its silicon packging. So from
driver's point of view there is no difference btw max1047 and max1050.
This patch adds the support to dynamically detect the chip type and
adds steps to initialize the max17047 chip.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
By using cm_notify_event function, charger driver can report several
charger events (e.g. battery full and external power in/out, etc) to
Charger-Manager. Charger-Manager can properly and immediately control
chargers by the reported event.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
Charger-Manager needs to check battery health in normal state
as well as suspend-to-RAM state. When the battery is fully charged,
Charger-Manager needs to determine when the chargers restart charging.
This patch allows Charger-Manager to monitor battery health in normal
state and handle operation for chargers after battery is fully charged.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
Driver support for the Summit I²C battery charger. This is used in some
Intel devices.
Signed-off-by: Bruce E. Robertson <bruce.e.robertson@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
Add power on reset (POR) init procedure defined by the maxim
appnote. Using this procedure ensures that the part is
configured/initialized correctly at POR and improves early accuracy of
the fuel gauge and informs the fuel gauge with the battery
characterization parameters. The battery characterization parameters
come from the maxim characterization procedure.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
align the register names with max17042 data sheet removing
registers that are marked reserved that are not used.
Add register definitions defined in the maxim initialization appnote
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
|
|
Now that this driver is named more generally, this change updates
the internal variables, defines and functions to use this new name.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
This driver for the bq20z75 implemented the register spec defined
by the SBS standard. As this is not unique to this the TI part this
was originally written for, we can generalize this driver to
show its support for any SBS compliant battery.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Charger Manager provides power-supply-class aggregating
information from multiple chargers and a fuel-gauge.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Because battery health monitoring should be done even when suspended,
it needs to wake up and suspend periodically. Thus, userspace battery
monitoring may incur too much overhead; every device and task is woken
up periodically. Charger Manager uses suspend-again to provide
in-suspend monitoring.
This patch allows to monitor battery health in-suspend state.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
This patch supports additional properties (PRESENT, CYCLE_COUNT,
VOLTAGE_MAX, VOLTAGE_MIN_DESIGN, CURRENT_NOW, CURRENT_AVG,
CHARGE_FULL, and TEMP).
Plus, initialization code for registers is added.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Adding support for external power change notification. One problem found
is that there is a lag time before the sensor will return a new status.
To ensure that we only fire off the power_supply_changed event when the
status returned from the sensor is actually different, we delay sending
the the notification, and instead poll on it looking for a change. The
amount of time to poll is configurable via platform data.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
The ISP1704/1707 chip can be put to full power down
state by asserting the CHIP_SEL line. This patch enables
platform or board specific hooks to put the device into
power down mode in case not needed.
This patch is a preparation for enabling this powering
routine in n900 (rx-51) devices.
Thanks to Heikki Krogerus for helping out with the patch.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Acked-By: Heikki Krogerus <heikki.krogerus@nokia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
MAX8903 is an integrated battery charger and selector with two
power inputs (USB and AC adapter). This driver enables the charger,
handles interrupts, and provides power-supply-class information to
userland.
Tested on Exynos4 NURI / S5PC210 SLP7 boards.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
With the support of platform data, now adding support for option i2c
retries on read/write failures. Ths is specified through the optional
platform data.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
