summaryrefslogtreecommitdiffstats
path: root/include/linux/smsc911x.h
AgeCommit message (Collapse)Author
2011-04-13net: allow shifted access in smsc911x V2Mathieu J. Poirier
This is a revised patch that permits a shifted access to the LAN9221 registers. More specifically: It adds a shift parameter in the platform_data. It introduces an ops in smsc911x_data. A choice of access function to use at run-time. Four new shifted access function. Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Alessandro Rubini <rubini@gnudd.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-13net: smsc911x: allow platform_data to specify mac addressManuel Lauss
Extend the driver to accept a MAC address specified in platform_data. Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-28smsc911x: add fifo byteswap support V2Magnus Damm
This is V2 of the smsc911x fifo byteswap patch. The smsc911x hardware supports both big and little and endian hardware configurations, and the linux smsc911x driver currently detects word order. For correct operation on big endian platforms lacking swapped byte lanes the following patch is needed. Only fifo data is swapped, register data does not require any swapping. Signed-off-by: Magnus Damm <damm@igel.co.jp> Acked-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-01smsc911x: allow mac address to be saved before device resetSteve Glendinning
Some platforms (for example pcm037) do not have an EEPROM fitted, instead storing their mac address somewhere else. The bootloader fetches this and configures the ethernet adapter before the kernel is started. This patch allows a platform to indicate to the driver via the SMSC911X_SAVE_MAC_ADDRESS flag that the mac address has already been configured via such a mechanism, and should be saved before resetting the chip. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Tested-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-01smsc911x: add external phy detection overridesSteve Glendinning
On LAN9115/LAN9117/LAN9215/LAN9217, external phys are supported. These are usually indicated by a hardware strap which sets an "external PHY detected" bit in the HW_CFG register. In some cases it is desirable to override this hardware strap and force use of either the internal phy or an external PHY. This patch adds SMSC911X_FORCE_INTERNAL_PHY and SMSC911X_FORCE_EXTERNAL_PHY flags so a platform can indicate this preference via its platform_data. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Tested-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-12-10smsc911x: add dynamic bus configurationSteve Glendinning
Convert the driver to select 16-bit or 32-bit bus access at runtime, at a small performance cost. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-06SMSC LAN911x and LAN921x vendor driverSteve Glendinning
Attached is a driver for SMSC's LAN911x and LAN921x families of embedded ethernet controllers. There is an existing smc911x driver in the tree; this is intended to replace it. Dustin McIntire (the author of the smc911x driver) has expressed his support for switching to this driver. This driver contains workarounds for all known hardware issues, and has been tested on all flavours of the chip on multiple architectures. This driver now uses phylib, so this patch also adds support for the device's internal phy Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: Bahadir Balban <Bahadir.Balban@arm.com> Signed-off-by: Dustin Mcintire <dustin@sensoria.com> Signed-off-by: Bill Gatliff <bgat@billgatliff.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>