summaryrefslogtreecommitdiffstats
path: root/include/linux/spi
AgeCommit message (Collapse)Author
2009-04-21spi: documentation: emphasise spi_master.setup() semanticsDavid Brownell
This is a doc-only patch which I hope will reduce the number of spi_master controller driver patches starting out with a common implementation bug. (As in: almost every spi_master driver I see starts out with its version of this bug. Sigh.) It just re-emphasizes that the setup() method may be called for one device while a transfer is active on another ... which means that most driver implementations shouldn't touch any registers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-16Merge branch 'next' into for-linusDmitry Torokhov
2009-04-11Input: ads7846 - introduce platform specific way to synchronize samplingEric Miao
Noises can be introduced when LCD signals are being driven, some platforms provide a signal to assist the synchronization of this sampling procedure. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-04-08Merge branch 'next' into for-linusDmitry Torokhov
2009-04-07SPI: add dma_alignment field to spi_masterMike Rapoport
Some SPI controllers have restrictions on DMAable buffers alignemt. Currently if the buffer supplied by protocol driver is not properly aligned, the controller silently performs transfer in PIO mode. Addition of dma_alignment field to spi_master allows protocol drivers to perform proper alignment. Signed-off-by: Mike Rapoport <mike@compulab.co.il> Cc: Bryan Wu <bryan.wu@analog.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-02spi-gpio: allow operation without CS signalMichael Buesch
Change spi-gpio so that it is possible to drive SPI communications over GPIO without the need for a chipselect signal. This is useful in very small setups where there's only one slave device on the bus. This patch does not affect existing setups. I use this for a tiny communication channel between an embedded device and a microcontroller. There are not enough GPIOs available for chipselect and it's not needed anyway in this case. Signed-off-by: Michael Buesch <mb@bu3sch.de> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-02memory_accessor: implement the new memory_accessor interfaces for SPI EEPROMsDavid Brownell
- Define new setup() hook to export the accessor - Implement accessor methods Moves some error checking out of the sysfs interface code into the layer below it, which is now shared by both sysfs and memory access code. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-03-09Input: add AD7879 Touchscreen driverMichael Hennerich
[randy.dunlap@oracle.com: don't use bus_id] [dtor@mail.ru: locking and other fixups] Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2009-02-24Merge branch 'master' of /home/davem/src/GIT/linux-2.6/David S. Miller
2009-02-20spi_bitbang: add more lowlevel function documentationMichael Buesch
This adds more documentation of the lowlevel API to avoid future bugs. Signed-off-by: Michael Buesch <mb@bu3sch.de> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-09libertas: if_spi: add ability to call board specific setup/teardown methodsMike Rapoport
In certain cases it is required to perform board specific actions before activating libertas G-SPI interface. These actions may include power up of the chip, GPIOs setup, proper pin-strapping and SPI controller config. This patch adds ability to call board specific setup/teardown methods Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Andrey Yurovsky <andrey@cozybit.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-02-03Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2009-01-30headers_check fix: spi/spidev.hJaswinder Singh Rajput
fix the following 'make headers_check' warning: usr/include/linux/spi/spidev.h:83: found __[us]{8,16,32,64} type without #include <linux/types.h> Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
2009-01-29libertas: if_spi, driver for libertas GSPI devicesColin McCabe
Add initial support for libertas devices using a GSPI interface. This has been tested with the 8686. GSPI is intended to be used on embedded systems. Board-specific parameters are required (see libertas_spi.h). Thanks to everyone who took a look at the earlier versions of the patch. Signed-off-by: Colin McCabe <colin@cozybit.com> Signed-off-by: Andrey Yurovsky <andrey@cozybit.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-01-08backlight: add support for Toppoly TDO35S series to tdo24m lcd driverMike Rapoport
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
2009-01-07Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits) trivial: chack -> check typo fix in main Makefile trivial: Add a space (and a comma) to a printk in 8250 driver trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx trivial: Fix misspelling of "firmware" in powerpc Makefile trivial: Fix misspelling of "firmware" in usb.c trivial: Fix misspelling of "firmware" in qla1280.c trivial: Fix misspelling of "firmware" in a100u2w.c trivial: Fix misspelling of "firmware" in megaraid.c trivial: Fix misspelling of "firmware" in ql4_mbx.c trivial: Fix misspelling of "firmware" in acpi_memhotplug.c trivial: Fix misspelling of "firmware" in ipw2100.c trivial: Fix misspelling of "firmware" in atmel.c trivial: Fix misspelled firmware in Kconfig trivial: fix an -> a typos in documentation and comments trivial: fix then -> than typos in comments and documentation trivial: update Jesper Juhl CREDITS entry with new email trivial: fix singal -> signal typo trivial: Fix incorrect use of "loose" in event.c trivial: printk: fix indentation of new_text_line declaration trivial: rtc-stk17ta8: fix sparse warning ...
2009-01-06spi_gpio driverDavid Brownell
Generalize the old at91rm9200 "bootstrap" bitbanging SPI master driver as "spi_gpio", so it works with arbitrary GPIOs and can be configured through platform_data. Such SPI masters support: - any number of bus instances (bus_num is the platform_device.id) - any number of chipselects (one GPIO per spi_device) - all four SPI_MODE values, and SPI_CS_HIGH - i/o word sizes from 1 to 32 bits; - devices configured as with any other spi_master controller When configured using platform_data, this provides relatively low clock rates. On platforms that support inlined GPIO calls, significantly improved transfer speeds are also possible with a semi-custom driver. (It's still painful when accessing flash memory, but less so.) Sanity checked by using this version to replace both native controllers on a board with six different SPI slaves, relying on three different SPI_MODE_* values and both SPI_CS_HIGH settings for correct operation. [akpm@linux-foundation.org: cleanups] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Magnus Damm <damm@igel.co.jp> Tested-by: Magnus Damm <damm@igel.co.jp> Cc: Torgil Svensson <torgil.svensson@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-06trivial: fix then -> than typos in comments and documentationFrederik Schwarzer
- (better, more, bigger ...) then -> (...) than Signed-off-by: Frederik Schwarzer <schwarzerf@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-01-04spi.h uses/needs device.hRandy Dunlap
Include header files as used/needed: In file included from drivers/leds/leds-dac124s085.c:16: include/linux/spi/spi.h:66: error: field 'dev' has incomplete type include/linux/spi/spi.h: In function 'to_spi_device': include/linux/spi/spi.h:100: warning: type defaults to 'int' in declaration of '__mptr' ... Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-12-31mmc_spi: Add support for OpenFirmware bindingsAnton Vorontsov
The support is implemented via platform data accessors, new module (of_mmc_spi) will be created automatically when the driver compiles on OpenFirmware platforms. Link-time dependency will load the module automatically. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-10-30spi: fix compile errorFernando Luis Vazquez Cao
Fix compile error below: LD drivers/spi/built-in.o CC [M] drivers/spi/spi_gpio.o In file included from drivers/spi/spi_gpio.c:26: include/linux/spi/spi_bitbang.h:23: error: field `work' has incomplete type make[2]: *** [drivers/spi/spi_gpio.o] Error 1 make[1]: *** [drivers/spi] Error 2 make: *** [drivers] Error 2 Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-16orion_spi: handle 88F6183 erratumLennert Buytenhek
Add support to orion_spi for the 88F6183 ARM SoC by adding code to work around a 6183-specific erratum. Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-09-25[ARM] corgi_lcd: use GPIO API for BACKLIGHT_ON and BACKLIGHT_CONTEric Miao
Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-23lcd: add corgibl_limit_intensity() to corgi_lcdEric Miao
This is not generic enough, added here for backward compatibility. And make this an individual commit so future revert will be a bit easier. Signed-off-by: Eric Miao <eric.miao@marvell.com> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-23lcd: add SPI-based LCD and backlight driver for SHARP corgi/spitzEric Miao
The driver is based on different source files including corgi_ssp.c, corgi_lcd.c and corgi_bl.c, previously authored by Richard Purdie and many others. The LCD and Backlight device actually share the same SPI device, so they are made into this single driver. Signed-off-by: Eric Miao <eric.miao@marvell.com> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-09-17Input: ads7846 - introduce .gpio_pendown to get pendown stateEric Miao
The GPIO connected to ADS7846 nPENIRQ signal is usually used to get the pendown state as well. Introduce a .gpio_pendown, and use this to decide the pendown state if .get_pendown_state is NULL. Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2008-08-05spi: new orion_spi driverShadi Ammouri
This adds an SPI driver for the SPI controller found in various Marvell Orion ARM SoCs. It currently supports only one slave, which must use SPI mode 0. [dbrownell@users.sourceforge.net: cleanups, meet specs, pass "sparse"] Signed-off-by: Shadi Ammouri <shadi@marvell.com> Signed-off-by: Saeed Bishara <saeed@marvell.com> Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-25spi: split up spi_new_device() to allow two stage registration.Grant Likely
spi_new_device() allocates and registers an spi device all in one swoop. If the driver needs to add extra data to the spi_device before it is registered, then this causes problems. This is needed for OF device tree support so that the SPI device tree helper can add a pointer to the device node after the device is allocated, but before the device is registered. OF aware SPI devices can then retrieve data out of the device node to populate a platform data structure. This patch splits the allocation and registration portions of code out of spi_new_device() and creates two new functions; spi_alloc_device() and spi_register_device(). spi_new_device() is modified to use the new functions for allocation and registration. None of the existing users of spi_new_device() should be affected by this change. Drivers using the new API can forego the use of spi_board_info structure to describe the device layout and populate data into the spi_device structure directly. This change is in preparation for adding an OF device tree parser to generate spi_devices based on data in the device tree. Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Acked-by: David Brownell <dbrownell@users.sourceforge.net>
2008-07-25gpio: mcp23s08 handles multiple chips per chipselectDavid Brownell
Teach the mcp23s08 driver about a curious feature of these chips: up to four of them can share the same chipselect, with the SPI signals wired in parallel, by matching two bits in the first protocol byte against two address lines on the chip. This is handled by three software changes: * Platform data now holds an array of per-chip structs, not just one chip's address and pullup configuration. * Probe() and remove() now use another level of structure, wrapping an instance of the original structure for each mcp23s08 chip sharing that chipselect. * The HAEN bit is set, so that the hardware address bits can no longer be ignored (boot firmware may not have enabled them). The "one struct per chip" preserves the guts of the current code, but platform_data will need minor changes. OLD: /* incorrect "slave" ID may not have mattered */ .slave = 3, .pullups = BIT(3) | BIT(1) | BIT(0), NEW: /* slave address _must_ match chip's wiring */ .chip[3] = { .is_present = true, .pullups = BIT(3) | BIT(1) | BIT(0), }, There's no change in how things _behave_ for spi_device nodes with a single mcp23s08 chip. New multi-chip configurations assign GPIOs in sequence, without holes. The spi_device just resembles a bigger controller, but internally it has multiple gpio_chip instances. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24rtc: ds1305/ds1306 driverDavid Brownell
Support the Dallas/Maxim DS1305 and DS1306 RTC chips. These use SPI, and support alarms, NVRAM, and a trickle charger for use when their backup power supply is a supercap or rechargeable cell. This basic driver doesn't yet support suspend/resume or wakealarms. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-24spi: make spi_board_info.modalias a char arrayGrant Likely
Currently, 'modalias' in the spi_device structure is a 'const char *'. The spi_new_device() function fills in the modalias value from a passed in spi_board_info data block. Since it is a pointer copy, the new spi_device remains dependent on the spi_board_info structure after the new spi_device is registered (no other fields in spi_device directly depend on the spi_board_info structure; all of the other data is copied). This causes a problem when dynamically propulating the list of attached SPI devices. For example, in arch/powerpc, the list of SPI devices can be populated from data in the device tree. With the current code, the device tree adapter must kmalloc() a new spi_board_info structure for each new SPI device it finds in the device tree, and there is no simple mechanism in place for keeping track of these allocations. This patch changes modalias from a 'const char *' to a fixed char array. By copying the modalias string instead of referencing it, the dependency on the spi_board_info structure is eliminated and an outside caller does not need to maintain a separate spi_board_info allocation for each device. If searched through the code to the best of my ability for any references to modalias which may be affected by this change and haven't found anything. It has been tested with the lite5200b platform in arch/powerpc. [dbrownell@users.sourceforge.net: cope with linux-next changes: KOBJ_NAME_LEN obliterated, etc] Signed-off-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (79 commits) arm: bus_id -> dev_name() and dev_set_name() conversions sparc64: fix up bus_id changes in sparc core code 3c59x: handle pci_name() being const MTD: handle pci_name() being const HP iLO driver sysdev: Convert the x86 mce tolerant sysdev attribute to generic attribute sysdev: Add utility functions for simple int/ulong variable sysdev attributes sysdev: Pass the attribute to the low level sysdev show/store function driver core: Suppress sysfs warnings for device_rename(). kobject: Transmit return value of call_usermodehelper() to caller sysfs-rules.txt: reword API stability statement debugfs: Implement debugfs_remove_recursive() HOWTO: change email addresses of James in HOWTO always enable FW_LOADER unless EMBEDDED=y uio-howto.tmpl: use unique output names uio-howto.tmpl: use standard copyright/legal markings sysfs: don't call notify_change sysdev: fix debugging statements in registration code. kobject: should use kobject_put() in kset-example kobject: reorder kobject to save space on 64 bit builds ...
2008-07-22gpio: gpio driver for max7301 SPI GPIO expanderJuergen Beisert
Maxim's MAX7301 is an SPI GPIO expander with 28 GPIOs. Note: MAX7301's interrupt feature is not supported yet. [akpm@linux-foundation.org: coding-style fixes] [g.liakhovetski@pengutronix.de: Fix inaccuracies in comments, check spi_setup() return code, mask off high byte in max7301_read()] Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de> Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-07-21driver core: remove KOBJ_NAME_LEN defineKay Sievers
Kobjects do not have a limit in name size since a while, so stop pretending that they do. Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-07-15mmc_spi: add support for card-detection pollingAnton Vorontsov
This patch adds new platform data variable "caps", so platforms could pass theirs capabilities into MMC core (for example, platforms without interrupt on the CD line will most probably want to pass MMC_CAP_NEEDS_POLL). New platform get_cd() callback provided to optimize polling. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-06-02mmc_spi: mmc_spi.h should include linux/interrupts.hAnton Vorontsov
Since mmc_spi.h uses irqreturn_t type, it should include appropriate header, otherwise build will break if users didn't include it (some of them do not use interrupts). Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-04-02Input: ads7846 - simplify support of external vREF (and ads7843)David Brownell
This updates the ads7846 driver to handle external vREF (required on boards using ads7843 chips) without module parameters, and also removes a needless variable with its associated bogus gcc warning. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2008-02-05mcp23s08 spi gpio expander supportDavid Brownell
Basic driver for 8-bit SPI based MCP23S08 GPIO expander, without support for IRQs or the shared chipselect mechanism. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Jean Delvare <khali@linux-fr.org> Cc: Eric Miao <eric.miao@marvell.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: Philipp Zabel <philipp.zabel@gmail.com> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16Merge branch 'linus' of master.kernel.org:/pub/scm/linux/kernel/git/perex/alsaLinus Torvalds
* 'linus' of master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa: (264 commits) [ALSA] version 1.0.15 [ALSA] Fix thinko in cs4231 mce down check [ALSA] sun-cs4231: improved waiting after MCE down [ALSA] sun-cs4231: use cs4231-regs.h [ALSA] This simplifies and fixes waiting loops of the mce_down() [ALSA] This patch adds support for a wavetable chip on [ALSA] This patch removes open_mutex from the ad1848-lib as [ALSA] fix bootup crash in snd_gus_interrupt() [ALSA] hda-codec - Fix SKU ID function for realtek codecs [ALSA] Support ASUS P701 eeepc [0x1043 0x82a1] support [ALSA] hda-codec - Add array terminator for dmic in STAC codec [ALSA] hdsp - Fix zero division [ALSA] usb-audio - Fix double comment [ALSA] hda-codec - Fix STAC922x volume knob control [ALSA] Changed Jaroslav Kysela's e-mail from perex@suse.cz to perex@perex.cz [ALSA] hda-codec - Fix for Fujitsu Lifebook C1410 [ALSA] mpu-401: remove MPU401_INFO_UART_ONLY flag [ALSA] mpu-401: do not require an ACK byte for the ENTER_UART command [ALSA] via82xx - Add DXS quirk for Shuttle AK31v2 [ALSA] hda-codec - Fix input_mux numbers for vaio stac92xx ...
2007-10-16spi doesn't need class_deviceTony Jones
Make the SPI framework and drivers stop using class_device. Update docs accordingly ... highlighting just which sysfs paths should be "safe"/stable. Signed-off-by: Tony Jones <tonyj@suse.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16[ALSA] ALSA sound driver for the AT73C213 DAC using Atmel SSC driverHans-Christian Egtvedt
This patch adds support for the AT73C213 DAC using the misc Atmel SSC driver in I2S mode. The driver also requires a SPI to setup the registers and control volume. It has been tested with an AT32AP7000 on the ATSTK1000 development board. The driver should also work with any Atmel device with an SSC module supported by the Atmel SSC driver (atmel-ssc). The atmel-ssc driver is just submitted to the Linux kernel. Please see mail thread http://lkml.org/lkml/2007/7/16/32 Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
2007-09-23mmc_spi host driverDavid Brownell
This is the latest version of the MMC-over-SPI support. It works on 2.6.23-rc2 plus git-mmc (from rc1-mm2), along with the preceding patches which teach the rest of the MMC stack about SPI. The main issue of note is that sometimes cards need to be power cycled to recover after certain faults. Also, it may sometimes be necessary to disable CRCs. ("modprobe mmc_core use_spi_crc=n") Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: mikael.starvik@axis.com, Cc: Hans-Peter Nilsson <hp@axis.com> Cc: Jan Nikitenko <jan.nikitenko@gmail.com> Cc: Mike Lavender <mike@steroidmicros.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2007-07-31spi kerneldoc updateDavid Brownell
This adds kerneldoc to the SPI framework. The "spi_driver" and "spi_board_info" structs were previously not described. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-31spidev supports more communications modesAnton Vorontsov
The spidev driver doesn't currently expose all SPI communications modes to userspace. This passes them all through to the driver. Two of them are potentially troublesome, in the sense that they could cause hardware conflicts on shared busses. It might be appropriate to add some privilege checks for for those modes. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-31SPI loopback mode definitionAnton Vorontsov
Loopback mode is supported by various controllers. This mode can be useful for testing, especially in conjunction with spidev driver. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-18Input: ads7846 - re-check pendown status before reporting eventsSemih Hazar
Pendown status from the PENIRQ pin is currently read only at the beginning of a sample set. If the pen is lifted just after sampling has began then sampled values become wrong. This patch adds an optional platform penirq_recheck_delay attribute. If non-zero, samples are only reported to the input subsystem if PENIRQ is still active that long after the samples taken. Signed-off-by: Semih Hazar <semih.hazar@indefia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2007-07-18Input: ads7846 - introduce sample settling delaySemih Hazar
The ads7846 driver has support for filtering, but when the chip gets deselected between samples this causes noise. This patch adds support for an optional settling delay time, so that two consecutive samples will be taken with the specified delay time apart. This ensures that the chip won't be deselected, so the noise won't appear. Filtering can still be done, but will have less work to do since each time a new sample is taken the same delay applies. Signed-off-by: Semih Hazar <semih.hazar@indefia.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
2007-07-17SPI: tle620x power switch driverBen Dooks
Add support for the Infineon TLE62x0 series of low-side driver chips, such as the TLE6220 or TLE6230. These can be viewed as output GPIOs specialized for power switching applications. The driver provides a userspace interface to those GPIOs, and to the switch status they provide. Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17SPI: add 3wire mode flagDavid Brownell
Add a new spi->mode bit: SPI_3WIRE, for chips where the SI and SO signals are shared (and which are thus only half duplex). Update the LM70 driver to require support for that hardware mode from the controller. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17SPI controller drivers: check for unsupported modesDavid Brownell
Minor SPI controller driver updates: make the setup() methods reject spi->mode bits they don't support, by masking aginst the inverse of bits they *do* support. This insures against misbehavior later when new mode bits get added. Most controllers can't support SPI_LSB_FIRST; more handle SPI_CS_HIGH. Support for all four SPI clock/transfer modes is routine. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>