| Age | Commit message (Collapse) | Author |
|---|
|
Like with commit 3c739ad0df5eb41cd7adad879eda6aa09879eb76
it is not always enough to specify all the pins of a gpio_chip
from offset zero to be added to a pin map range, since the
mapping from GPIO to pin controller may not be linear at all,
but need to be broken into a few consecutive sub-ranges or
1-pin entries for complicated cases. The ranges may also be
sparse.
This alters the signature of the function to accept offsets
into both the GPIO-chip local pinspace and the pin controller
local pinspace.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
The <*/gpio.h> includes are updated again: now we need to account
for the problem introduced by commit:
595679a8038584df7b9398bf34f61db3c038bfea
"gpiolib: fix up function prototypes etc"
Actually we need static inlines in include/asm-generic/gpio.h
as well since we may have GPIOLIB but not PINCTRL.
Make sure to move all the CONFIG_PINCTRL business
to the end of the file so we are sure we have
declared struct gpio_chip.
And we need to keep the static inlines in <linux/gpio.h>
but here for the !CONFIG_GENERIC_GPIO case, and then we
may as well throw in a few warnings like the other
prototypes there, if someone would have the bad taste
of compiling without GENERIC_GPIO even.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The fact that of_gpiochip_add_pin_range() and
gpiochip_add_pin_range() share too much code is fragile and
will invariably mean that bugs need to be fixed in two places
instead of one.
So separate the concerns of gpiolib.c and gpiolib-of.c and
have the latter call the former as back-end. This is necessary
also when going forward with other device descriptions such
as ACPI.
This is done by:
- Adding a return code to gpiochip_add_pin_range() so we can
reliably check whether this succeeds.
- Get rid of the custom of_pinctrl_add_gpio_range() from
pinctrl. Instead create of_pinctrl_get() to just retrive the
pin controller per se from an OF node. This composite
function was just begging to be deleted, it was way to
purpose-specific.
- Use pinctrl_dev_get_name() to get the name of the retrieved
pin controller and use that to call back into the generic
gpiochip_add_pin_range().
Now the pin range is only allocated and tied to a pin
controller from the core implementation in gpiolib.c.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit 69e1601bca88809dc118abd1becb02c15a02ec71
"gpiolib: provide provision to register pin ranges"
Got most of it's function prototypes wrong, so fix this up by:
- Moving the void declarations into static inlines in
<linux/gpio.h> (previously the actual prototypes were declared
here...)
- Declare the gpiochip_add_pin_range() and
gpiochip_remove_pin_ranges() functions in <asm-generic/gpio.h>
together with the pin range struct declaration itself.
- Actually only implement these very functions in gpiolib.c
if CONFIG_PINCTRL is set.
- Additionally export the symbols since modules will need to
be able to do this.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This switches the COH 901 pinctrl driver to allocate its GPIO
IRQs dynamically, and start to use a linear irqdomain to map
from the hardware IRQs.
This way we can cut away the complex allocation of IRQ numbers
from the <mach/irqs.h> file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
pinctrl subsystem needs gpio chip base to prepare set of gpio
pin ranges, which a given pinctrl driver can handle. This is
important to handle pinctrl gpio request calls in order to
program a given pin properly for gpio operation.
As gpio base is allocated dynamically during gpiochip
registration, presently there exists no clean way to pass this
information to the pinctrl subsystem.
After few discussions from [1], it was concluded that may be
gpio controller reporting the pin range it supports, is a
better way than pinctrl subsystem directly registering it.
[1] http://comments.gmane.org/gmane.linux.ports.arm.kernel/184816
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
[Edited documentation a bit]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This reverts earlier commit which removed
pinctrl_remove_gpio_range(), because at that time there
weren't any more users of that routine. It was removed as the
removal of ranges was done in unregister of pinctrl.
But as we are now registering stuff from gpiolib, we may
remove and insert a gpio module multiple times. So, we
need this routine again.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pull networking fixes from David Miller:
"Bug fixes galore, mostly in drivers as is often the case:
1) USB gadget and cdc_eem drivers need adjustments to their frame size
lengths in order to handle VLANs correctly. From Ian Coolidge.
2) TIPC and several network drivers erroneously call tasklet_disable
before tasklet_kill, fix from Xiaotian Feng.
3) r8169 driver needs to apply the WOL suspend quirk to more chipsets,
fix from Cyril Brulebois.
4) Fix multicast filters on RTL_GIGA_MAC_VER_35 r8169 chips, from
Nathan Walp.
5) FDB netlink dumps should use RTM_NEWNEIGH as the message type, not
zero. From John Fastabend.
6) Fix smsc95xx tx checksum offload on big-endian, from Steve
Glendinning.
7) __inet_diag_dump() needs to repsect and report the error value
returned from inet_diag_lock_handler() rather than ignore it.
Otherwise if an inet diag handler is not available for a particular
protocol, we essentially report success instead of giving an error
indication. Fix from Cyrill Gorcunov.
8) When the QFQ packet scheduler sees TSO/GSO packets it does not
handle things properly, and in fact ends up corrupting it's
datastructures as well as mis-schedule packets. Fix from Paolo
Valente.
9) Fix oopser in skb_loop_sk(), from Eric Leblond.
10) CXGB4 passes partially uninitialized datastructures in to FW
commands, fix from Vipul Pandya.
11) When we send unsolicited ipv6 neighbour advertisements, we should
send them to the link-local allnodes multicast address, as per
RFC4861. Fix from Hannes Frederic Sowa.
12) There is some kind of bug in the usbnet's kevent deferral
mechanism, but more immediately when it triggers an uncontrolled
stream of kernel messages spam the log. Rate limit the error log
message triggered when this problem occurs, as sending thousands
of error messages into the kernel log doesn't help matters at all,
and in fact makes further diagnosis more difficult.
From Steve Glendinning.
13) Fix gianfar restore from hibernation, from Wang Dongsheng.
14) The netlink message attribute sizes are wrong in the ipv6 GRE
driver, it was using the size of ipv4 addresses instead of ipv6
ones :-) Fix from Nicolas Dichtel."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
gre6: fix rtnl dump messages
gianfar: ethernet vanishes after restoring from hibernation
usbnet: ratelimit kevent may have been dropped warnings
ipv6: send unsolicited neighbour advertisements to all-nodes
net: usb: cdc_eem: Fix rx skb allocation for 802.1Q VLANs
usb: gadget: g_ether: fix frame size check for 802.1Q
cxgb4: Fix initialization of SGE_CONTROL register
isdn: Make CONFIG_ISDN depend on CONFIG_NETDEVICES
cxgb4: Initialize data structures before using.
af-packet: fix oops when socket is not present
pkt_sched: enable QFQ to support TSO/GSO
net: inet_diag -- Return error code if protocol handler is missed
net: bnx2x: Fix typo in bnx2x driver
smsc95xx: fix tx checksum offload for big endian
rtnetlink: Use nlmsg type RTM_NEWNEIGH from dflt fdb dump
ptp: update adjfreq callback description
r8169: allow multicast packets on sub-8168f chipset.
r8169: Fix WoL on RTL8168d/8111d.
drivers/net: use tasklet_kill in device remove/close process
tipc: do not use tasklet_disable before tasklet_kill
|
|
Pull sparc fixes from David Miller:
"Several build/bug fixes for sparc, including:
1) Configuring a mix of static vs. modular sparc64 crypto modules
didn't work, remove an ill-conceived attempt to only have to build
the device match table for these drivers once to fix the problem.
Reported by Meelis Roos.
2) Make the montgomery multiple/square and mpmul instructions actually
usable in 32-bit tasks. Essentially this involves providing 32-bit
userspace with a way to use a 64-bit stack when it needs to.
3) Our sparc64 atomic backoffs don't yield cpu strands properly on
Niagara chips. Use pause instruction when available to achieve
this, otherwise use a benign instruction we know blocks the strand
for some time.
4) Wire up kcmp
5) Fix the build of various drivers by removing the unnecessary
blocking of OF_GPIO when SPARC.
6) Fix unintended regression wherein of_address_to_resource stopped
being provided. Fix from Andreas Larsson.
7) Fix NULL dereference in leon_handle_ext_irq(), also from Andreas
Larsson."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix build with mix of modular vs. non-modular crypto drivers.
sparc: Support atomic64_dec_if_positive properly.
of/address: sparc: Declare of_address_to_resource() as an extern function for sparc again
sparc32, leon: Check for existent irq_map entry in leon_handle_ext_irq
sparc: Add sparc support for platform_get_irq()
sparc: Allow OF_GPIO on sparc.
qlogicpti: Fix build warning.
sparc: Wire up sys_kcmp.
sparc64: Improvde documentation and readability of atomic backoff code.
sparc64: Use pause instruction when available.
sparc64: Fix cpu strand yielding.
sparc64: Make montmul/montsqr/mpmul usable in 32-bit threads.
|
|
for sparc again
This bug-fix makes sure that of_address_to_resource is defined extern for sparc
so that the sparc-specific implementation of of_address_to_resource() is once
again used when including include/linux/of_address.h in a sparc context. A
number of drivers in mainline relies on this function working for sparc.
The bug was introduced in a850a7554442f08d3e910c6eeb4ee216868dda1e, "of/address:
add empty static inlines for !CONFIG_OF". Contrary to that commit title, the
static inlines are added for !CONFIG_OF_ADDRESS, and CONFIG_OF_ADDRESS is never
defined for sparc. This is good behavior for the other functions in
include/linux/of_address.h, as the extern functions defined in
drivers/of/address.c only gets linked when OF_ADDRESS is configured. However,
for of_address_to_resource there exists a sparc-specific implementation in
arch/sparc/arch/sparc/kernel/of_device_common.c
Solution suggested by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- sdhci: fix a NULL dereference at resume-time, seen on OLPC XO-4
- sdhci: fix against 3.7-rc1 for UHS modes without a vqmmc regulator
- sdhci-of-esdhc: disable CMD23 on boards where it's broken
- sdhci-s3c: fix against 3.7-rc1 for card detection with runtime PM
- dw_mmc, omap_hsmmc: fix potential NULL derefs, compiler warnings
* tag 'mmc-fixes-for-3.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: sdhci-s3c: fix the card detection in runtime-pm
mmc: sdhci-s3c: use clk_prepare_enable and clk_disable_unprepare
mmc: dw_mmc: constify dw_mci_idmac_ops in exynos back-end
mmc: dw_mmc: fix modular build for exynos back-end
mmc: sdhci: fix NULL dereference in sdhci_request() tuning
mmc: sdhci: fix IS_ERR() checking of regulator_get()
mmc: fix sdhci-dove probe/removal
mmc: sh_mmcif: fix use after free
mmc: sdhci-pci: fix 'Invalid iomem size' error message condition
mmc: mxcmmc: Fix MODULE_ALIAS
mmc: omap_hsmmc: fix NULL pointer dereference for dt boot
mmc: omap_hsmmc: fix host reference after mmc_free_host
mmc: dw_mmc: fix multiple drv_data NULL dereferences
mmc: dw_mmc: enable controller interrupt before calling mmc_start_host
mmc: sdhci-of-esdhc: disable CMD23 for some Freescale SoCs
mmc: dw_mmc: remove _dev_info compile warning
mmc: dw_mmc: convert the variable type of irq
|
|
The of_device_id match data is now marked as const and
must not be modified. This changes the dw_mmc to mark
all pointers passing the dw_mci_drv_data or dw_mci_dma_ops
structures as const, and also marks the static definitions
as const.
drivers/mmc/host/dw_mmc-exynos.c: In function 'dw_mci_exynos_probe':
drivers/mmc/host/dw_mmc-exynos.c:234:11: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
CMD23 causes lots of errors in kernel on some freescale SoCs
(P1020, P1021, P1022, P1024, P1025 and P4080) when MMC card used,
which is because these controllers does not support CMD23,
even on the SoCs which declares CMD23 is supported.
Therefore, we'll not use CMD23.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Even though platform_get_irq returns error, 'host->irq'
always has an unsigned value. Less-than-zero comparison
of an unsigned value is never true. Type of 'unsigned int'
will be changed for 'int'.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This patch updates the adjfreq callback description to include a note that the
delta in ppb is always relative to the base frequency, and not to the current
frequency of the hardware clock.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
CC: stable@vger.kernel.org [v3.5+]
CC: Richard Cochran <richard.cochran@gmail.com>
CC: John Stultz <john.stultz@linaro.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This hashtable implementation is using hlist buckets to provide a simple
hashtable to prevent it from getting reimplemented all over the kernel.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
[ Merging this now, so that subsystems can start applying Sasha's
patches that use this - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull KVM fix from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: fix vcpu->mmio_fragments overflow
|
|
After commit b3356bf0dbb349 (KVM: emulator: optimize "rep ins" handling),
the pieces of io data can be collected and write them to the guest memory
or MMIO together
Unfortunately, kvm splits the mmio access into 8 bytes and store them to
vcpu->mmio_fragments. If the guest uses "rep ins" to move large data, it
will cause vcpu->mmio_fragments overflow
The bug can be exposed by isapc (-M isapc):
[23154.818733] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
[ ......]
[23154.858083] Call Trace:
[23154.859874] [<ffffffffa04f0e17>] kvm_get_cr8+0x1d/0x28 [kvm]
[23154.861677] [<ffffffffa04fa6d4>] kvm_arch_vcpu_ioctl_run+0xcda/0xe45 [kvm]
[23154.863604] [<ffffffffa04f5a1a>] ? kvm_arch_vcpu_load+0x17b/0x180 [kvm]
Actually, we can use one mmio_fragment to store a large mmio access then
split it when we pass the mmio-exit-info to userspace. After that, we only
need two entries to store mmio info for the cross-mmio pages access
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Pull md fixes from NeilBrown:
"Some fixes for md in 3.7
- one recently introduced crash for dm-raid10 with discard
- one bug in new functionality that has been around for a few
releases.
- minor bug in md's 'faulty' personality
and UAPI disintegration for md."
* tag 'md-3.7-fixes' of git://neil.brown.name/md:
MD RAID10: Fix oops when creating RAID10 arrays via dm-raid.c
md/raid1: Fix assembling of arrays containing Replacements.
md faulty: use disk_stack_limits()
UAPI: (Scripted) Disintegrate include/linux/raid
|
|
This merges the old <plat/pincfg.h> header into
<linux/platform_data/pinctrl-nomadik.h> and rids us of
yet one more <plat/*> include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This moves the platform data header for the Nomadik pin controller
to <linux/platform_data/pinctrl-nomadik.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use rcu_read_lock_sched / rcu_read_unlock_sched / synchronize_sched
instead of rcu_read_lock / rcu_read_unlock / synchronize_rcu.
This is an optimization. The RCU-protected region is very small, so
there will be no latency problems if we disable preempt in this region.
So we use rcu_read_lock_sched / rcu_read_unlock_sched that translates
to preempt_disable / preempt_disable. It is smaller (and supposedly
faster) than preemptible rcu_read_lock / rcu_read_unlock.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch introduces new barrier pair light_mb() and heavy_mb() for
percpu rw semaphores.
This patch fixes a bug in percpu-rw-semaphores where a barrier was
missing in percpu_up_write.
This patch improves performance on the read path of
percpu-rw-semaphores: on non-x86 cpus, there was a smp_mb() in
percpu_up_read. This patch changes it to a compiler barrier and removes
the "#if defined(X86) ..." condition.
From: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull networking fixes from David Miller:
"This is what we usually expect at this stage of the game, lots of
little things, mostly in drivers. With the occasional 'oops didn't
mean to do that' kind of regressions in the core code."
1) Uninitialized data in __ip_vs_get_timeouts(), from Arnd Bergmann
2) Reject invalid ACK sequences in Fast Open sockets, from Jerry Chu.
3) Lost error code on return from _rtl_usb_receive(), from Christian
Lamparter.
4) Fix reset resume on USB rt2x00, from Stanislaw Gruszka.
5) Release resources on error in pch_gbe driver, from Veaceslav Falico.
6) Default hop limit not set correctly in ip6_template_metrics[], fix
from Li RongQing.
7) Gianfar PTP code requests wrong kind of resource during probe, fix
from Wei Yang.
8) Fix VHOST net driver on big-endian, from Michael S Tsirkin.
9) Mallenox driver bug fixes from Jack Morgenstein, Or Gerlitz, Moni
Shoua, Dotan Barak, and Uri Habusha.
10) usbnet leaks memory on TX path, fix from Hemant Kumar.
11) Use socket state test, rather than presence of FIN bit packet, to
determine FIONREAD/SIOCINQ value. Fix from Eric Dumazet.
12) Fix cxgb4 build failure, from Vipul Pandya.
13) Provide a SYN_DATA_ACKED state to complement SYN_FASTOPEN in socket
info dumps. From Yuchung Cheng.
14) Fix leak of security path in kfree_skb_partial(). Fix from Eric
Dumazet.
15) Handle RX FIFO overflows more resiliently in pch_gbe driver, from
Veaceslav Falico.
16) Fix MAINTAINERS file pattern for networking drivers, from Jean
Delvare.
17) Add iPhone5 IDs to IPHETH driver, from Jay Purohit.
18) VLAN device type change restriction is too strict, and should not
trigger for the automatically generated vlan0 device. Fix from Jiri
Pirko.
19) Make PMTU/redirect flushing work properly again in ipv4, from
Steffen Klassert.
20) Fix memory corruptions by using kfree_rcu() in netlink_release().
From Eric Dumazet.
21) More qmi_wwan device IDs, from Bjørn Mork.
22) Fix unintentional change of SNAT/DNAT hooks in generic NAT
infrastructure, from Elison Niven.
23) Fix 3.6.x regression in xt_TEE netfilter module, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
tilegx: fix some issues in the SW TSO support
qmi_wwan/cdc_ether: move Novatel 551 and E362 to qmi_wwan
net: usb: Fix memory leak on Tx data path
net/mlx4_core: Unmap UAR also in the case of error flow
net/mlx4_en: Don't use vlan tag value as an indication for vlan presence
net/mlx4_en: Fix double-release-range in tx-rings
bas_gigaset: fix pre_reset handling
vhost: fix mergeable bufs on BE hosts
gianfar_ptp: use iomem, not ioports resource tree in probe
ipv6: Set default hoplimit as zero.
NET_VENDOR_TI: make available for am33xx as well
pch_gbe: fix error handling in pch_gbe_up()
b43: Fix oops on unload when firmware not found
mwifiex: clean up scan state on error
mwifiex: return -EBUSY if specific scan request cannot be honored
brcmfmac: fix potential NULL dereference
Revert "ath9k_hw: Updated AR9003 tx gain table for 5GHz"
ath9k_htc: Add PID/VID for a Ubiquiti WiFiStation
rt2x00: usb: fix reset resume
rtlwifi: pass rx setup error code to caller
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg Kroah-Hartman:
"Here are some staging driver fixes for your 3.7-rc tree.
Nothing major here, a number of iio driver fixups that were causing
problems, some comedi driver bugfixes, and a bunch of tidspbridge
warning squashing and other regressions fixed from the 3.6 release.
All have been in the linux-next releases for a bit.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (32 commits)
staging: tidspbridge: delete unused mmu functions
staging: tidspbridge: ioremap physical address of the stack segment in shm
staging: tidspbridge: ioremap dsp sync addr
staging: tidspbridge: change type to __iomem for per and core addresses
staging: tidspbridge: drop const from custom mmu implementation
staging: tidspbridge: request the right irq for mmu
staging: ipack: add missing include (implicit declaration of function 'kfree')
staging: ramster: depends on NET
staging: omapdrm: fix allocation size for page addresses array
staging: zram: Fix handling of incompressible pages
Staging: android: binder: Allow using highmem for binder buffers
Staging: android: binder: Fix memory leak on thread/process exit
staging: comedi: ni_labpc: fix possible NULL deref during detach
staging: comedi: das08: fix possible NULL deref during detach
staging: comedi: amplc_pc263: fix possible NULL deref during detach
staging: comedi: amplc_pc236: fix possible NULL deref during detach
staging: comedi: amplc_pc236: fix invalid register access during detach
staging: comedi: amplc_dio200: fix possible NULL deref during detach
staging: comedi: 8255_pci: fix possible NULL deref during detach
staging: comedi: ni_daq_700: fix dio subdevice regression
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are a number of firmware core fixes for 3.7, and some other minor
fixes. And some documentation updates thrown in for good measure.
All have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Documentation:Chinese translation of Documentation/arm64/memory.txt
Documentation:Chinese translation of Documentation/arm64/booting.txt
Documentation:Chinese translation of Documentation/IRQ.txt
firmware loader: document kernel direct loading
sysfs: sysfs_pathname/sysfs_add_one: Use strlcat() instead of strcat()
dynamic_debug: Remove unnecessary __used
firmware loader: sync firmware cache by async_synchronize_full_domain
firmware loader: let direct loading back on 'firmware_buf'
firmware loader: fix one reqeust_firmware race
firmware loader: cancel uncache work before caching firmware
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg Kroah-Hartman:
"Here are some driver fixes for 3.7. They include extcon driver fixes,
a hyper-v bugfix, and two other minor driver fixes.
All of these have been in the linux-next releases for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
sonypi: suspend/resume callbacks should be conditionally compiled on CONFIG_PM_SLEEP
Drivers: hv: Cleanup error handling in vmbus_open()
extcon : register for cable interest by cable name
extcon: trivial: kfree missed from remove path
extcon: driver model release call not needed
extcon: MAX77693: Add platform data for MUIC device to initialize registers
extcon: max77693: Use max77693_update_reg for rmw operations
extcon: Fix kerneldoc for extcon_set_cable_state and extcon_set_cable_state_
extcon: adc-jack: Add missing MODULE_LICENSE
extcon: adc-jack: Fix checking return value of request_any_context_irq
extcon: Fix return value in extcon_register_interest()
extcon: unregister compat link on cleanup
extcon: Unregister compat class at module unload to fix oops
extcon: optimising the check_mutually_exclusive function
extcon: standard cable names definition and declaration changed
extcon-max8997: remove usage of ret in max8997_muic_handle_charger_type_detach
extcon: Remove duplicate inclusion of extcon.h header file
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"This fixes a couple of nasty page table initialization bugs which were
causing kdump regressions. A clean rearchitecturing of the code is in
the works - meanwhile these are reverts that restore the
best-known-working state of the kernel.
There's also EFI fixes and other small fixes."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, mm: Undo incorrect revert in arch/x86/mm/init.c
x86: efi: Turn off efi_enabled after setup on mixed fw/kernel
x86, mm: Find_early_table_space based on ranges that are actually being mapped
x86, mm: Use memblock memory loop instead of e820_RAM
x86, mm: Trim memory in memblock to be page aligned
x86/irq/ioapic: Check for valid irq_cfg pointer in smp_irq_move_cleanup_interrupt
x86/efi: Fix oops caused by incorrect set_memory_uc() usage
x86-64: Fix page table accounting
Revert "x86/mm: Fix the size calculation of mapping tables"
MAINTAINERS: Add EFI git repository location
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Most of the kernel diffstat relates to a group of Intel P6 and KNC
(Xeon-Phi Knights Corner) PMU driver fixes, neither of which is in
heavy use, so we took the fixes.
The rest is diverse smallish fixes to the tooling and kernel side."
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Remove unused variable in nhmex_rbox_alter_er()
perf/x86: Enable overflow on Intel KNC with a custom knc_pmu_handle_irq()
perf/x86: Remove cpuc->enable check on Intl KNC event enable/disable
perf/x86: Make Intel KNC use full 40-bit width of counters
perf/x86/uncore: Handle pci_read_config_dword() errors
perf/x86: Remove P6 cpuc->enabled check
perf/x86: Update/fix generic events on P6 PMU
perf/x86: Fix P6 FP_ASSIST event constraint
perf, cpu hotplug: Use cached value of smp_processor_id()
perf, cpu hotplug: Run CPU_STARTING notifiers with irqs disabled
x86/perf: Fix virtualization sanity check
perf test: Fix exclude_guest parse events tests
perf tools: do not flush maps on COMM for perf report
perf help: Fix --help for builtins
perf trace: Check if sample raw_data field is set
perf trace: Validate syscall id before growing syscall table
|
|
rb_erase_augmented() is a static function annotated with
__always_inline. This causes a compile failure when attempting to use
the rbtree implementation as a library (e.g. kvm tool):
rbtree_augmented.h:125:24: error: expected `=', `,', `;', `asm' or `__attribute__' before `void'
Include linux/compiler.h in rbtree_augmented.h so that the __always_inline
macro is resolved correctly.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Pekka Enberg <penberg@kernel.org>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull spi fixes from Mark Brown:
"A bunch of fixes here, mostly minor except for the pl022 which has
just been a bit of a shambles all round, the recent runtime PM changes
have as far as I can tell never worked so they're just getting thrown
out."
* tag 'spi-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
spi/pl022: Revert recent runtime PM changes
spi: tsc2005: delete soon-obsolete e-mail address
spi: spi-rspi: fix build error for the latest shdma driver
|
|
The __used attribute prevents gcc from eliminating
unnecessary, otherwise optimized away, metadata for
debugging logging messages.
Remove the __used attribute.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We will not map partial pages, so need to make sure memblock
allocation will not allocate those bytes out.
Also we will use for_each_mem_pfn_range() to loop to map memory
range to keep them consistent.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/CAE9FiQVZirvaBMFYRfXMmWEcHbKSicQEHz4VAwUv0xFCk51ZNw@mail.gmail.com
Acked-by: Jacob Shin <jacob.shin@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
|
|
The perf_cpu_notifier() macro invokes smp_processor_id()
multiple times. Optimize it by using a local variable.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: peterz@infradead.org
Cc: acme@ghostprotocols.net
Link: http://lkml.kernel.org/r/20121016075817.3572.76733.stgit@srivatsabhat.in.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The CPU_STARTING notifiers are supposed to be run with irqs
disabled. But the perf_cpu_notifier() macro invokes them without
doing that. Fix it.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: peterz@infradead.org
Cc: acme@ghostprotocols.net
Link: http://lkml.kernel.org/r/20121016075809.3572.47848.stgit@srivatsabhat.in.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch add platform data for MUIC device to initialize register
on probe() call because it should unmask interrupt mask register
and initialize some register related to MUIC device.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
Add a bit TCPI_OPT_SYN_DATA (32) to the socket option TCP_INFO:tcpi_options.
It's set if the data in SYN (sent or received) is acked by SYN-ACK. Server or
client application can use this information to check Fast Open success rate.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With this change now individual drivers can use standard cable
names as below:
static const char *arizona_cable[] = {
extcon_cable_name[EXTCON_USB],
extcon_cable_name[EXTCON_USB_HOST],
"CUSTOM_CABLE"
NULL,
}
Signed-off-by: anish kumar <anish198519851985@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/oleg/misc into perf/urgent
Pull various uprobes bugfixes from Oleg Nesterov - mostly race and
failure path fixes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Merge misc fixes from Andrew Morton:
"Seven fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (7 patches)
lib/dma-debug.c: fix __hash_bucket_find()
mm: compaction: correct the nr_strict va isolated check for CMA
firmware/memmap: avoid type conflicts with the generic memmap_init()
pidns: remove recursion from free_pid_ns()
drivers/video/backlight/lm3639_bl.c: return proper error in lm3639_bled_mode_store() error paths
kernel/sys.c: fix stack memory content leak via UNAME26
linux/coredump.h needs asm/siginfo.h
|
|
free_pid_ns() operates in a recursive fashion:
free_pid_ns(parent)
put_pid_ns(parent)
kref_put(&ns->kref, free_pid_ns);
free_pid_ns
thus if there was a huge nesting of namespaces the userspace may trigger
avalanche calling of free_pid_ns leading to kernel stack exhausting and a
panic eventually.
This patch turns the recursion into an iterative loop.
Based on a patch by Andrew Vagin.
[akpm@linux-foundation.org: export put_pid_ns() to modules]
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Andrew Vagin <avagin@openvz.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 5ab1c309b344 ("coredump: pass siginfo_t* to do_coredump() and
below, not merely signr") added siginfo_t to linux/coredump.h but forgot
to include asm/siginfo.h. This breaks the build for UML/i386. (And any
other arch where asm/siginfo.h is not magically preincluded...)
In file included from arch/x86/um/elfcore.c:2:0: include/linux/coredump.h:15:25: error: unknown type name 'siginfo_t'
make[1]: *** [arch/x86/um/elfcore.o] Error 1
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: "Jonathan M. Foote" <jmfoote@cert.org>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Pedro Alves <palves@redhat.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY fixes from Greg Kroah-Hartman:
"Here are some tty and serial driver fixes for your 3.7-rc1 tree.
Again, the UABI header file fixes, and a number of build and runtime
serial driver bugfixes that solve problems people have been reporting
(the staging driver is a tty driver, hence the fixes coming in through
this tree.)
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
staging: dgrp: check return value of alloc_tty_driver
staging: dgrp: check for NULL pointer in (un)register_proc_table
serial/8250_hp300: Missing 8250 register interface conversion bits
UAPI: (Scripted) Disintegrate include/linux/hsi
tty: serial: sccnxp: Fix bug with unterminated platform_id list
staging: serial: dgrp: Add missing #include <linux/uaccess.h>
serial: sccnxp: Allows the driver to be compiled as a module
tty: Fix bogus "callbacks suppressed" messages
net, TTY: initialize tty->driver_data before usage
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are the USB patches against your 3.7-rc1 tree.
There are the usual UABI header file movements, and we finally are now
able to remove the dbg() macro that is over 15 years old (that had to
wait for after some other trees got merged into yours during the big
3.7-rc1 merge window.)
Other than that, nothing major, just a number of bugfixes and new
device ids. It turns out that almost all of the usb-serial drivers
had bugs in how they were handling their internal data, leaking
memory, hence all of those fixups.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (42 commits)
USB: option: add more ZTE devices
USB: option: blacklist net interface on ZTE devices
usb: host: xhci: New system added for Compliance Mode Patch on SN65LVPE502CP
USB: io_ti: fix sysfs-attribute creation
USB: iuu_phoenix: fix sysfs-attribute creation
USB: spcp8x5: fix port-data memory leak
USB: ssu100: fix port-data memory leak
USB: ti_usb_3410_5052: fix port-data memory leak
USB: oti6858: fix port-data memory leak
USB: iuu_phoenix: fix port-data memory leak
USB: kl5kusb105: fix port-data memory leak
USB: io_ti: fix port-data memory leak
USB: keyspan_pda: fix port-data memory leak
USB: f81232: fix port-data memory leak
USB: io_edgeport: fix port-data memory leak
USB: kobil_sct: fix port-data memory leak
USB: cypress_m8: fix port-data memory leak
usb: acm: fix the computation of the number of data bits
usb: Missing dma_mask in ehci-vt8500.c when probed from device-tree
usb: Missing dma_mask in uhci-platform.c when probed from device-tree
...
|
|
Some datasheets use a different unit to specify the channel scale than what IIO
expects it to be. This patch adds two helper macros which allow to convert units
commonly used in datasheets to IIO units:
* acceleration: g -> meter / second**2
* angular velocity: degree (/ second) -> rad (/ second)
This makes it much more convenient to specify and also easier to verify a
channel's scale attribute.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Media fixes for:
- one Kconfig fix patch;
- one patch fixing DocBook breakage due to the drivers/media UAPI
changes;
- the remaining UAPI media changes (DVB API).
I'm aware that is is a little late for the UAPI renames for the DVB
API, but IMHO, it is better to merge it for 3.7, due to two reasons:
1) There is a major rename at 3.7 (not only uapi changes, but also
the entire media drivers were reorganized on 3.7, in order to
simplify the Kconfig logic, and easy drivers selection, especially
for hybrid devices). By confining all those renames there at 3.7
it will cause all the harm at for media developers on just one
shot. Stable backports upstream and at distros will likely
welcome it as well, as they won't need to check what changed on
3.7 and what was postponed for on 3.8.
2) The V4L2 DocBook Makefile creates a cross-reference between the
media API headers and the specs. This helps us _a_lot_ to be sure
that all API improvements are properly documented. Every time a
header changes from one place to another, DocBook/media/Makefile
needs to be patched. Currently, the DocBook breakage patch
depends on the DVB UAPI."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] Kconfig: Fix dependencies for driver autoselect options
DocBook/media/Makefile: Fix build due to uapi breakage
UAPI: (Scripted) Disintegrate include/linux/dvb
|
|
Pull DeviceTree fixes from Rob Herring:
"A handful of fixes:
- a fix for dtc from upstream
- sparse fixes in DeviceTree code
- stub of_get_child_by_name for !OF builds"
* tag 'dt-fixes-for-3.7' of git://sources.calxeda.com/kernel/linux:
dtc: fix for_each_*() to skip first object if deleted
of/platform: sparse fix
of/irq: sparse fixes
of/address: sparse fixes
of: add stub of_get_child_by_name for non-OF builds
|
|
git://git.infradead.org/users/dhowells/linux-headers into tty-linus
UAPI Disintegration 2012-10-09
|
|
drivers/of/irq.c:195:57: warning: restricted __be32 degrades to integer
drivers/of/irq.c:196:51: warning: restricted __be32 degrades to integer
drivers/of/irq.c:199:57: warning: restricted __be32 degrades to integer
drivers/of/irq.c:201:58: warning: restricted __be32 degrades to integer
drivers/of/irq.c:470:37: warning: incorrect type in assignment (different modifiers)
drivers/of/irq.c:470:37: expected int ( *[usertype] irq_init_cb )( ... )
drivers/of/irq.c:470:37: got void const *const data
drivers/of/irq.c:96:5: error: symbol 'of_irq_map_raw' redeclared with different type (originally declared at include/linux/of_irq.h:61) - incompatible argument 2 (different base types)
drivers/of/of_pci_irq.c:91:40: warning: incorrect type in argument 2 (different base types)
drivers/of/of_pci_irq.c:91:40: expected unsigned int const [usertype] *intspec
drivers/of/of_pci_irq.c:91:40: got restricted __be32 *<noident>
drivers/of/of_pci_irq.c:91:53: warning: incorrect type in argument 4 (different base types)
drivers/of/of_pci_irq.c:91:53: expected unsigned int const [usertype] *addr
drivers/of/of_pci_irq.c:91:53: got restricted __be32 *<noident>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
|
