| Age | Commit message (Collapse) | Author |
|---|
|
Key points of this patch are:
- In case new SACK information is advance only type, no skb
processing below previously discovered highest point is done
- Optimize cases below highest point too since there's no need
to always go up to highest point (which is very likely still
present in that SACK), this is not entirely true though
because I'm dropping the fastpath_skb_hint which could
previously optimize those cases even better. Whether that's
significant, I'm not too sure.
Currently it will provide skipping by walking. Combined with
RB-tree, all skipping would become fast too regardless of window
size (can be done incrementally later).
Previously a number of cases in TCP SACK processing fails to
take advantage of costly stored information in sack_recv_cache,
most importantly, expected events such as cumulative ACK and new
hole ACKs. Processing on such ACKs result in rather long walks
building up latencies (which easily gets nasty when window is
huge). Those latencies are often completely unnecessary
compared with the amount of _new_ information received, usually
for cumulative ACK there's no new information at all, yet TCP
walks whole queue unnecessary potentially taking a number of
costly cache misses on the way, etc.!
Since the inclusion of highest_sack, there's a lot information
that is very likely redundant (SACK fastpath hint stuff,
fackets_out, highest_sack), though there's no ultimate guarantee
that they'll remain the same whole the time (in all unearthly
scenarios). Take advantage of this knowledge here and drop
fastpath hint and use direct access to highest SACKed skb as
a replacement.
Effectively "special cased" fastpath is dropped. This change
adds some complexity to introduce better coveraged "fastpath",
though the added complexity should make TCP behave more cache
friendly.
The current ACK's SACK blocks are compared against each cached
block individially and only ranges that are new are then scanned
by the high constant walk. For other parts of write queue, even
when in previously known part of the SACK blocks, a faster skip
function is used (if necessary at all). In addition, whenever
possible, TCP fast-forwards to highest_sack skb that was made
available by an earlier patch. In typical case, no other things
but this fast-forward and mandatory markings after that occur
making the access pattern quite similar to the former fastpath
"special case".
DSACKs are special case that must always be walked.
The local to recv_sack_cache copying could be more intelligent
w.r.t DSACKs which are likely to be there only once but that
is left to a separate patch.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is going to replace the sack fastpath hint quite soon... :-)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sock_valbool_flag() helper is used in setsockopt to
set or reset some flag on the sock. This helper is required
in the net/socket.c only, so move it there.
Besides, patch two places in sys_setsockopt() that repeat
this helper functionality manually.
Since this is not a bugfix, but a trivial cleanup, I
prepared this patch against net-2.6.25, but it also
applies (with a single offset) to the latest net-2.6.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Qdisc_class_ops are const, and Qdisc_ops are mostly read.
Using "const" and "__read_mostly" qualifiers helps to reduce false
sharing.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Policy table is implemented as an RCU linear list since we do not expect
large list nor frequent updates.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After changeset:
[NETFILTER]: Introduce NF_INET_ hook values
It always evaluates to NF_INET_POST_ROUTING.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IPv4 and IPv6 hook values are identical, yet some code tries to figure
out the "correct" value by looking at the address family. Introduce NF_INET_*
values for both IPv4 and IPv6. The old values are kept in a #ifndef __KERNEL__
section for userspace compatibility.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for async resumptions on input. To do so, the
transform would return -EINPROGRESS and subsequently invoke the
function xfrm_input_resume to resume processing.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The nhoff field isn't actually necessary in xfrm_input. For tunnel
mode transforms we now throw away the output IP header so it makes no
sense to fill in the nexthdr field. For transport mode we can now let
the function transport_finish do the setting and it knows where the
nexthdr field is.
The only other thing that needs the nexthdr field to be set is the
header extraction code. However, we can simply move the protocol
extraction out of the generic header extraction.
We want to minimise the amount of info we have to carry around between
transforms as this simplifies the resumption process for async crypto.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently x->lastused is u64 which means that it cannot be
read/written atomically on all architectures. David Miller observed
that the value stored in it is only an unsigned long which is always
atomic.
So based on his suggestion this patch changes the internal
representation from u64 to unsigned long while the user-interface
still refers to it as u64.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of the work on asynchronous cryptographic operations, we need
to be able to resume from the spot where they occur. As such, it
helps if we isolate them to one spot.
This patch moves most of the remaining family-specific processing into
the common input code.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for async resumptions on output. To do so,
the transform would return -EINPROGRESS and subsequently invoke the
function xfrm_output_resume to resume processing.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of the work on asynchrnous cryptographic operations, we need
to be able to resume from the spot where they occur. As such, it
helps if we isolate them to one spot.
This patch moves most of the remaining family-specific processing into
the common output code.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most callers of the LOCAL_OUT chain will set the IP packet length
before doing so. They also share the same output function dst_output.
This patch creates a new function called ip6_local_out which does all
of that and converts the appropriate users over to it.
Apart from removing duplicate code, it will also help in merging the
IPsec output path.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most callers of the LOCAL_OUT chain will set the IP packet length and
header checksum before doing so. They also share the same output
function dst_output.
This patch creates a new function called ip_local_out which does all
of that and converts the appropriate users over to it.
Apart from removing duplicate code, it will also help in merging the
IPsec output path once the same thing is done for IPv6.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With inter-family transforms the inner mode differs from the outer
mode. Attempting to handle both sides from the same function means
that it needs to handle both IPv4 and IPv6 which creates duplication
and confusion.
This patch separates the two parts on the input path so that each
function deals with one family only.
In particular, the functions xfrm4_extract_inut/xfrm6_extract_inut
moves the pertinent fields from the IPv4/IPv6 IP headers into a
neutral format stored in skb->cb. This is then used by the inner mode
input functions to modify the inner IP header. In this way the input
function no longer has to know about the outer address family.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With inter-family transforms the inner mode differs from the outer
mode. Attempting to handle both sides from the same function means
that it needs to handle both IPv4 and IPv6 which creates duplication
and confusion.
This patch separates the two parts on the output path so that each
function deals with one family only.
In particular, the functions xfrm4_extract_output/xfrm6_extract_output
moves the pertinent fields from the IPv4/IPv6 IP headers into a
neutral format stored in skb->cb. This is then used by the outer mode
output functions to write the outer IP header. In this way the output
function no longer has to know about the inner address family.
Since the extract functions are only called by tunnel modes (the only
modes that can support inter-family transforms), I've also moved the
xfrm*_tunnel_check_size calls into them. This allows the correct ICMP
message to be sent as opposed to now where you might call icmp_send
with an IPv6 packet and vice versa.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes the prototype of ipv4_copy_dscp and ipv6_copy_dscp so
that they directly take the outer DSCP rather than the outer IP header.
This will help us to unify the code for inter-family tunnels.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Half of the code in xfrm4_bundle_create and xfrm6_bundle_create are
common. This patch extracts that logic and puts it into
xfrm_bundle_create. The rest of it are then accessed through afinfo.
As a result this fixes the problem with inter-family transforms where
we treat every xfrm dst in the bundle as if it belongs to the top
family.
This patch also fixes a long-standing error-path bug where we may free
the xfrm states twice.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the flow construction from the callers of
xfrm_dst_lookup into that function. It also changes xfrm_dst_lookup
so that it takes an xfrm state as its argument instead of explicit
addresses.
This removes any address-specific logic from the callers of
xfrm_dst_lookup which is needed to correctly support inter-family
transforms.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The functions local_addr and remote_addr are more than what they're
needed for. The same thing can be done easily with flags on the type
object. This patch does that and simplifies the wrapper functions in
xfrm6_policy accordingly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The file net/netevent.h only refers to struct dst_entry * so it
doesn't need to include dst.h. I've replaced it with a forward
declaration.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have a number of copies of dst_discard scattered around the place
which all do the same thing, namely free a packet on the input or
output paths.
This patch deletes all of them except dst_discard and points all the
users to it.
The only non-trivial bit is decnet where it returns an error.
However, conceptually this is identical to the blackhole functions
used in IPv4 and IPv6 which do not return errors. So they should
either all return errors or all return zero. For now I've stuck with
the majority and picked zero as the return value.
It doesn't really matter in practice since few if any driver would
react differently depending on a zero return value or NET_RX_DROP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dst member nfheader_len is only used by IPv6. It's also currently
creating a rather ugly alignment hole in struct dst. Therefore this patch
moves it from there into struct rt6_info.
It also reorders the fields in rt6_info to minimize holes.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add raw drops counter for IPv4 in /proc/net/raw .
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support for network splice receive.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An IPoIB subnet on an IB fabric that spans multiple IB subnets can't
use link-local scope in multicast GIDs. The existing routines that
map IP/IPv6 multicast addresses into IB link-level addresses hard-code
the scope to link-local, and they also leave the partition key field
uninitialised. This patch adds a parameter (the link-level broadcast
address) to the mapping routines, allowing them to initialise both the
scope and the P_Key appropriately, and fixes up the call sites.
The next step will be to add a way to configure the scope for an IPoIB
interface.
Signed-off-by: Rolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
It seems commit fda9ef5d679b07c9d9097aaf6ef7f069d794a8f9 introduced a RCU
protection for sk_filter(), without a rcu_dereference()
Either we need a rcu_dereference(), either a comment should explain why we
dont need it. I vote for the former.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
alg_key_len is the length in bits of the key, not in bytes.
Best way to fix this is to move alg_len() function from net/xfrm/xfrm_user.c
to include/net/xfrm.h, and to use it in xfrm_algo_clone()
alg_len() is renamed to xfrm_alg_len() because of its global exposition.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both NetLabel and SELinux (other LSMs may grow to use it as well) rely
on the 'iif' field to determine the receiving network interface of
inbound packets. Unfortunately, at present this field is not
preserved across a skb clone operation which can lead to garbage
values if the cloned skb is sent back through the network stack. This
patch corrects this problem by properly copying the 'iif' field in
__skb_clone() and removing the 'iif' field assignment from
skb_act_clone() since it is no longer needed.
Also, while we are here, put the assignments in the same order as the
offsets to reduce cacheline bounces.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The even should be called SCTP_AUTHENTICATION_INDICATION.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move veth.h from net/ to linux/ since it is a user api, and add it to
user header processing Kbuild.
[ Use header-y as suggested by Sam Ravnborg. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some users do "modprobe ip_conntrack hashsize=...". Since we have the
module aliases this loads nf_conntrack_ipv4 and nf_conntrack, the
hashsize parameter is unknown for nf_conntrack_ipv4 however and makes
it fail.
Allow to specify hashsize= for both nf_conntrack and nf_conntrack_ipv4.
Note: the nf_conntrack message in the ringbuffer will display an
incorrect hashsize since nf_conntrack is first pulled in as a
dependency and calculates the size itself, then it gets changed
through a call to nf_conntrack_set_hashsize().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During accept/migrate the code attempts to copy the addresses from
the parent endpoint to the new endpoint. However, if the parent
was bound to a wildcard address, then we end up pointlessly copying
all of the current addresses on the system.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip_rt_advice has been gone, so no need to keep prototype and debug message.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SCTP-AUTH requires selection of CRYPTO, HMAC and SHA1 since
SHA1 is a MUST requirement for AUTH. We also support SHA256,
but that's optional, so fix the code to treat it as such.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
|
|
The inet_ehash_locks_alloc() looks like this:
#ifdef CONFIG_NUMA
if (size > PAGE_SIZE)
x = vmalloc(...);
else
#endif
x = kmalloc(...);
Unlike it, the inet_ehash_locks_alloc() looks like this:
#ifdef CONFIG_NUMA
if (size > PAGE_SIZE)
vfree(x);
else
#else
kfree(x);
#endif
The error is obvious - if the NUMA is on and the size
is less than the PAGE_SIZE we leak the pointer (kfree is
inside the #else branch).
Compiler doesn't warn us because after the kfree(x) there's
a "x = NULL" assignment, so here's another (minor?) bug: we
don't set x to NULL under certain circumstances.
Boring explanation, I know... Patch explains it better.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
if (net_ratelimit())
IEEE80211_DEBUG_DROP(...)
can pollute the logs with messages like:
printk: 1 messages suppressed.
printk: 2 messages suppressed.
printk: 7 messages suppressed.
if debugging information is disabled. These messages are printed by
net_ratelimit(). Add a wrapper to net_ratelimit() that takes into account
the log level, so that net_ratelimit() is called only when we really want
to print something.
Signed-off-by: Guillaume Chazarain <guichaz@yahoo.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When the abstraction functions got added, conversion here was
made incorrectly. As a result, the skb may end up pointing
to skb which got included to the probe skb and then was freed.
For it to trigger, however, skb_transmit must fail sending as
well.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch the remaining IPVS sysctl entries over to to use CTL_UNNUMBERED,
I stronly doubt that anyone is using the sys_sysctl interface to
these variables.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sysctl table check failed: /net/ipv4/vs/lblc_expiration .3.5.21.19 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/lblcr_expiration .3.5.21.20 Missing strategy
Switch these entried over to use CTL_UNNUMBERED as clearly
the sys_syscal portion wasn't working.
This is along the same lines as Christian Borntraeger's patch that fixes
up entries with no stratergy in net/ipv4/ipvs/ip_vs_ctl.c
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Running the latest git code I get the following messages during boot:
sysctl table check failed: /net/ipv4/vs/drop_entry .3.5.21.4 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/drop_packet .3.5.21.5 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/secure_tcp .3.5.21.6 Missing strategy
[...]
sysctl table check failed: /net/ipv4/vs/sync_threshold .3.5.21.24 Missing strategy
I removed the binary sysctl handler for those messages and also removed
the definitions in ip_vs.h. The alternative would be to implement a
proper strategy handler, but syscall sysctl is deprecated.
There are other sysctl definitions that are commented out or work with
the default sysctl_data strategy. I did not touch these.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Indeed my previous change to alloc_pskb has made it possible
for the TCP header to be misaligned iff the MTU is not a multiple
of 4 (and less than a page). So I suspect the optimised IPsec
MTU calculation is giving you just such an MTU :)
This patch fixes it by changing alloc_pskb to make sure that
the size is at least 32-bit aligned. This does not cause the
problem fixed by the previous patch because max_header is always
32-bit aligned which means that in the SG/NOTSO case this will
be a no-op.
I thought about putting this in the callers but all the current
callers are from TCP. If and when we get a non-TCP caller we
can always create a TCP wrapper for this function and move the
alignment over there.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The request_sock_queue's listen_opt is either vmalloc-ed or
kmalloc-ed depending on the number of table entries. Thus it
is expected to be handled properly on free, which is done in
the reqsk_queue_destroy().
However the error path in inet_csk_listen_start() calls
the lite version of reqsk_queue_destroy, called
__reqsk_queue_destroy, which calls the kfree unconditionally.
Fix this and move the __reqsk_queue_destroy into a .c file as
it looks too big to be inline.
As David also noticed, this is an error recovery path only,
so no locking is required and the lopt is known to be not NULL.
reqsk_queue_yank_listen_sk is also now only used in
net/core/request_sock.c so we should move it there too.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We round up the header size in sk_stream_alloc_pskb so that
TSO packets get zero tail room. Unfortunately this rounding
up is not coordinated with the select_size() function used by
TCP to calculate the second parameter of sk_stream_alloc_pskb.
As a result, we may allocate more than a page of data in the
non-TSO case when exactly one page is desired.
In fact, rounding up the head room is detrimental in the non-TSO
case because it makes memory that would otherwise be available to
the payload head room. TSO doesn't need this either, all it wants
is the guarantee that there is no tail room.
So this patch fixes this by adjusting the skb_reserve call so that
exactly the requested amount (which all callers have calculated in
a precise way) is made available as tail room.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reverts Eric's commit 2b008b0a8e96b726c603c5e1a5a7a509b5f61e35
It diets .text & .data section of the kernel if CONFIG_NET_NS is not set.
This is safe after list operations cleanup.
Signed-of-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The inetpeer.c tracks the LRU list of inet_perr-s, but makes
it by hands. Use the list_head-s for this.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
