| Age | Commit message (Collapse) | Author |
|---|
|
After the recent mq change there is the new select_queue qdisc class
method used in tc_modify_qdisc, but it works OK only for direct child
qdiscs of mq qdisc. Grandchildren always get the first tx queue, which
would give wrong qdisc_root etc. results (e.g. for sch_htb as child of
sch_prio). This patch fixes it by using parent's dev_queue for such
grandchildren qdiscs. The select_queue method's return type is changed
BTW.
With feedback from: Patrick McHardy <kaber@trash.net>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes commit e36b9d16c6a6d0f59803b3ef04ff3c22c3844c10. The approach
there is to call dev_close()/dev_open() whenever the device type is changed in
order to remap the device IP multicast addresses to HW multicast addresses.
This approach suffers from 2 drawbacks:
*. It assumes tha the device is UP when calling dev_close(), or otherwise
dev_close() has no affect. It is worth to mention that initscripts (Redhat)
and sysconfig (Suse) doesn't act the same in this matter.
*. dev_close() has other side affects, like deleting entries from the routing
table, which might be unnecessary.
The fix here is to directly remap the IP multicast addresses to HW multicast
addresses for a bonding device that changes its type, and nothing else.
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was once upon time so that snd_sthresh was a 16-bit quantity.
...That has not been true for long period of time. I run across
some ancient compares which still seem to trust such legacy.
Put all that magic into a single place, I hopefully found all
of them.
Compile tested, though linking of allyesconfig is ridiculous
nowadays it seems.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove long removed "inet_protocol_base" declaration.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-next-2.6
|
|
When new child qdiscs are attached to the mq qdisc, they are actually
attached as root qdiscs to the device queues. The lock selection for
new estimators incorrectly picks the root lock of the existing and
to be replaced qdisc, which results in a use-after-free once the old
qdisc has been destroyed.
Mark mq qdisc instances with a new flag and treat qdiscs attached to
mq as children similar to regular root qdiscs.
Additionally prevent estimators from being attached to the mq qdisc
itself since it only updates its byte and packet counters during dumps.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a classful dummy scheduler which can be used as root qdisc
for multiqueue devices and exposes each device queue as a child class.
This allows to address queues individually and graft them similar to regular
classes. Additionally it presents an accumulated view of the statistics of
all real root qdiscs in the dummy root.
Two new callbacks are added to the qdisc_ops and qdisc_class_ops:
- cl_ops->select_queue selects the tx queue number for new child classes.
- qdisc_ops->attach() overrides root qdisc device grafting to attach
non-shared qdiscs to the queues.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It will be used in a following patch by the multiqueue qdisc.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This shrinks the size of struct sctp_association a little.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
|
|
This patch introduces a new sysctl option to make IPv4 Address Scoping
configurable <draft-stewart-tsvwg-sctp-ipv4-00.txt>.
In networking environments where DNAT rules in iptables prerouting
chains convert destination IP's to link-local/private IP addresses,
SCTP connections fail to establish as the INIT chunk is dropped by the
kernel due to address scope match failure.
For example to support overlapping IP addresses (same IP address with
different vlan id) a Layer-5 application listens on link local IP's,
and there is a DNAT rule that maps the destination IP to a link local
IP. Such applications never get the SCTP INIT if the address-scoping
draft is strictly followed.
This sysctl configuration allows SCTP to function in such
unconventional networking environments.
Sysctl options:
0 - Disable IPv4 address scoping draft altogether
1 - Enable IPv4 address scoping (default, current behavior)
2 - Enable address scoping but allow IPv4 private addresses in init/init-ack
3 - Enable address scoping but allow IPv4 link local address in init/init-ack
Signed-off-by: Bhaskar Dutta <bhaskar.dutta@globallogic.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
|
|
This shrinks the size of sctp_packet a little.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
|
|
We had a bug that we never stored the user-defined value for
MAXSEG when setting the value on an association. Thus future
PMTU events ended up re-writing the frag point and increasing
it past user limit. Additionally, when setting the option on
the socket/endpoint, we effect all current associations, which
is against spec.
Now, we store the user 'maxseg' value along with the computed
'frag_point'. We inherit 'maxseg' from the socket at association
creation and use it as an upper limit for 'frag_point' when its
set.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
|
|
SCTP will delay the last part of a large write due to NAGLE, if that
part is smaller then MTU. Since we are doing large writes, we might
as well send the last portion now instead of waiting untill the next
large write happens. The small portion will be sent as is regardless,
so it's better to not delay it.
This is a result of much discussions with Wei Yongjun <yjwei@cn.fujitsu.com>
and Doug Graham <dgraham@nortel.com>. Many thanks go out to them.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
|
|
SCTP has a problem that when small chunks are used, it is possible
to exhaust the receiver buffer without fully closing receive window.
This happens due to all overhead that we have account for with small
messages. To fix this, when receive buffer is exceeded, we'll drop
the window to 0 and save the 'drop' portion. When application starts
reading data and freeing up recevie buffer space, we'll wait until
we've reached the 'drop' window and then add back this 'drop' one
mtu at a time. This worked well in testing and under stress produced
rather even recovery.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
|
|
Currenlty, sctp breaks up user messages into fragments and
sends each fragment to the lower layer by itself. This means
that for each fragment we go all the way down the stack
and back up. This also discourages bundling of multiple
fragments when they can fit into a sigle packet (ex: due
to user setting a low fragmentation threashold).
We introduce a new command SCTP_CMD_SND_MSG and hand the
whole message down state machine. The state machine and
the side-effect parser will cork the queue, add all chunks
from the message to the queue, and then un-cork the queue
thus causing the chunks to get transmitted.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
|
|
If a socket has a lot of association that are in the process of
of being closed/aborted, it is possible for a remote to establish
new associations during the time period that the old ones are shutting
down. If this was a result of a close() call, there will be no socket
and will cause a memory leak. We'll prevent this by setting the
socket state to CLOSING and disallow new associations when in this state.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
|
|
This patch removes an unused union definition (sctp_cmsg_data_t)
from include/net/sctp/user.h.
Signed-off-by: Rami Rosen <rosenrami@gmail.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
|
|
This fixed a lockdep warning which appeared when doing stress
memory tests over NFS:
inconsistent {RECLAIM_FS-ON-W} -> {IN-RECLAIM_FS-W} usage.
page reclaim => nfs_writepage => tcp_sendmsg => lock sk_lock
mount_root => nfs_root_data => tcp_close => lock sk_lock =>
tcp_send_fin => alloc_skb_fclone => page reclaim
David raised a concern that if the allocation fails in tcp_send_fin(), and it's
GFP_ATOMIC, we are going to yield() (which sleeps) and loop endlessly waiting
for the allocation to succeed.
But fact is, the original GFP_KERNEL also sleeps. GFP_ATOMIC+yield() looks
weird, but it is no worse the implicit sleep inside GFP_KERNEL. Both could
loop endlessly under memory pressure.
CC: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
CC: David S. Miller <davem@davemloft.net>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vlan devices are currently not multi-queue capable.
We can do that with a new rtnl_link_ops method,
get_tx_queues(), called from rtnl_create_link()
This new method gets num_tx_queues/real_num_tx_queues
from real device.
register_vlan_device() is also handled.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function block inet_connect_sock_af_ops contains no data
make it constant.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/yellowfin.c
|
|
These are full of unresolved problems, mainly that conversions don't
work 1-1 from hrtimers to tasklet_hrtimers because unlike hrtimers
tasklets can't be killed from softirq context.
And when a qdisc gets reset, that's exactly what we need to do here.
We'll work this out in the net-next-2.6 tree and if warranted we'll
backport that work to -stable.
This reverts the following 3 changesets:
a2cb6a4dd470d7a64255a10b843b0d188416b78f
("pkt_sched: Fix bogon in tasklet_hrtimer changes.")
38acce2d7983632100a9ff3fd20295f6e34074a8
("pkt_sched: Convert CBQ to tasklet_hrtimer.")
ee5f9757ea17759e1ce5503bdae2b07e48e32af9
("pkt_sched: Convert qdisc_watchdog to tasklet_hrtimer")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These tables are never modified at runtime. Move to read-only
section.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch affects the retransmits_timed_out() function.
Changes:
1) Variables have more meaningful names
2) retransmits_timed_out() has an introductionary comment.
3) Small coding style changes.
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct net::ipv6.ip6_dst_ops is separatedly dynamically allocated,
but there is no fundamental reason for it. Embed it directly into
struct netns_ipv6.
For that:
* move struct dst_ops into separate header to fix circular dependencies
I honestly tried not to, it's pretty impossible to do other way
* drop dynamical allocation, allocate together with netns
For a change, remove struct dst_ops::dst_net, it's deducible
by using container_of() given dst_ops pointer.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFC 1122 specifies two threshold values R1 and R2 for connection timeouts,
which may represent a number of allowed retransmissions or a timeout value.
Currently linux uses sysctl_tcp_retries{1,2} to specify the thresholds
in number of allowed retransmissions.
For any desired threshold R2 (by means of time) one can specify tcp_retries2
(by means of number of retransmissions) such that TCP will not time out
earlier than R2. This is the case, because the RTO schedule follows a fixed
pattern, namely exponential backoff.
However, the RTO behaviour is not predictable any more if RTO backoffs can be
reverted, as it is the case in the draft
"Make TCP more Robust to Long Connectivity Disruptions"
(http://tools.ietf.org/html/draft-zimmermann-tcp-lcd).
In the worst case TCP would time out a connection after 3.2 seconds, if the
initial RTO equaled MIN_RTO and each backoff has been reverted.
This patch introduces a function retransmits_timed_out(N),
which calculates the timeout of a TCP connection, assuming an initial
RTO of MIN_RTO and N unsuccessful, exponentially backed-off retransmissions.
Whenever timeout decisions are made by comparing the retransmission counter
to some value N, this function can be used, instead.
The meaning of tcp_retries2 will be changed, as many more RTO retransmissions
can occur than the value indicates. However, it yields a timeout which is
similar to the one of an unpatched, exponentially backing off TCP in the same
scenario. As no application could rely on an RTO greater than MIN_RTO, there
should be no risk of a regression.
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Here, an ICMP host/network unreachable message, whose payload fits to
TCP's SND.UNA, is taken as an indication that the RTO retransmission has
not been lost due to congestion, but because of a route failure
somewhere along the path.
With true congestion, a router won't trigger such a message and the
patched TCP will operate as standard TCP.
This patch reverts one RTO backoff, if an ICMP host/network unreachable
message, whose payload fits to TCP's SND.UNA, arrives.
Based on the new RTO, the retransmission timer is reset to reflect the
remaining time, or - if the revert clocked out the timer - a retransmission
is sent out immediately.
Backoffs are only reverted, if TCP is in RTO loss recovery, i.e. if
there have been retransmissions and reversible backoffs, already.
Changes from v2:
1) Renaming of skb in tcp_v4_err() moved to another patch.
2) Reintroduced tcp_bound_rto() and __tcp_set_rto().
3) Fixed code comments.
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support of dcbnl setapp/getapp to dcbnl_rtnl_ops in netdev to allow
LLDs to implement their corresponding dcbnl setapp/getapp ops to support
the IEEE 802.1Q DCBX setapp/getapp commands.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/holtmann/bluetooth-next-2.6
|
|
Introduce keepalive_probes(tp) helper, and use it, like
keepalive_time_when(tp) and keepalive_intvl_when(tp)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the libipw naming scheme change, it is no longer necessary for
mac80211 to avoid the ieee80211_rx name clash.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This eliminates the dual definition of ieee80211_channel (and possibly
others), further clarifying who defines what and paving the way for
inclusion of cfg80211.h.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Implement all issues related to RemoteBusy in the RECV state table.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
Consitfy nlmsghdr arguments to a couple of functions as preparation
for the next patch, which will constify the netlink message data in
all nfnetlink users.
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lowpan/lowpan
|
|
None of this stuff should execute in hw IRQ context, therefore
use a tasklet_hrtimer so that it runs in softirq context.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When using DEFER_SETUP on a RFCOMM socket, a SABM frame triggers
authorization which when rejected send a DM response. This is fine
according to the RFCOMM spec:
the responding implementation may replace the "proper" response
on the Multiplexer Control channel with a DM frame, sent on the
referenced DLCI to indicate that the DLCI is not open, and that
the responder would not grant a request to open it later either.
But some stacks doesn't seems to cope with this leaving DLCI 0 open after
receiving DM frame.
To fix it properly a timer was introduced to rfcomm_session which is used
to set a timeout when the last active DLC of a session is unlinked, this
will give the remote stack some time to reply with a proper DISC frame on
DLCI 0 avoiding both sides sending DISC to each other on stacks that
follow the specification and taking care of those who don't by taking
down DLCI 0.
Signed-off-by: Luiz Augusto von Dentz <luiz.dentz@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Support for receiving of SREJ frames as specified by the state table.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When L2CAP loses an I-frame we send a SREJ frame to the transmitter side
requesting the lost packet. This patch implement all Recv I-frame events
on SREJ_SENT state table except the ones that deal with SendRej (the REJ
exception at receiver side is yet not implemented).
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Implement CRC16 check for L2CAP packets. FCS is used by Streaming Mode and
Enhanced Retransmission Mode and is a extra check for the packet content.
Using CRC16 is the default, L2CAP won't use FCS only when both side send
a "No FCS" request.
Initially based on a patch from Nathan Holstein <nathan@lampreynetworks.com>
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
L2CAP uses retransmission and monitor timers to inquiry the other side
about unacked I-frames. After sending each I-frame we (re)start the
retransmission timer. If it expires, we start a monitor timer that send a
S-frame with P bit set and wait for S-frame with F bit set. If monitor
timer expires, try again, at a maximum of L2CAP_DEFAULT_MAX_TX.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When receiving an I-frame with unexpected txSeq, receiver side start the
recovery procedure by sending a REJ S-frame to the transmitter side. So
the transmitter can re-send the lost I-frame.
This patch just adds a basic support for retransmission, it doesn't
mean that ERTM now has full support for packet retransmission.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
ERTM should use Segmentation and Reassembly to break down a SDU in many
PDUs on sending data to the other side.
On sending packets we queue all 'segments' until end of segmentation and
just the add them to the queue for sending. On receiving we create a new
SKB with the SDU reassembled.
Initially based on a patch from Nathan Holstein <nathan@lampreynetworks.com>
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds support for ERTM transfers, without retransmission, with
txWindow up to 63 and with acknowledgement of packets received. Now the
packets are queued before call l2cap_do_send(), so packets couldn't be
sent at the time we call l2cap_sock_sendmsg(). They will be sent in
an asynchronous way on later calls of l2cap_ertm_send(). Besides if an
error occurs on calling l2cap_do_send() we disconnect the channel.
Initially based on a patch from Nathan Holstein <nathan@lampreynetworks.com>
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add support to config_req and config_rsp to configure ERTM and Streaming
mode. If the remote device specifies ERTM or Streaming mode, then the
same mode is proposed. Otherwise ERTM or Basic mode is used. And in case
of a state 2 device, the remote device should propose the same mode. If
not, then the channel gets disconnected.
Signed-off-by: Gustavo F. Padovan <gustavo@las.ic.unicamp.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
To enable Enhanced Retransmission mode it needs to be set via a socket
option. A different mode can be set on a socket, but on listen() and
connect() the mode is checked and ERTM is only allowed if it is enabled
via the module parameter.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
hdev->req_lock is used as mutex so make it a mutex.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The device model itself has no real usable reference counting at the
moment and this causes problems if parents are deleted before their
children. The device model itself handles the memory details of this
correctly, but the uevent order is not consistent. This causes various
problems for systems like HAL or even X.
So until device_put() does a proper cleanup, the device for Bluetooth
connection will be protected with an extra reference counting to ensure
the correct order of uevents when connections are terminated.
This is not an automatic feature. Higher Bluetooth layers like HIDP or
BNEP should grab this new reference to ensure that their uevents are
send before the ones from the parent device.
Based on a report by Brian Rogers <brian@xyzw.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
