Age | Commit message (Collapse) | Author |
|
Allows device MMC boot partitions to be accessed. MMC partitions are
treated effectively as separate block devices on the same MMC card.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
CMD6 is an R1B-type command, where DAT is used as busy. Depending
on register written using CMD6, timeout value can be different
as per spec.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Renames erase_timeout to cmd_timeout_ms inside struct mmc_command.
First step to making host honor timeouts for non-data-transfer
commands. Cleans up erase timeout code.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Fix data truncation warnings: .manfid is not unsigned long:
drivers/mmc/core/quirks.c:36: warning: large integer implicitly truncated to unsigned type
drivers/mmc/core/quirks.c:40: warning: large integer implicitly truncated to unsigned type
drivers/mmc/core/quirks.c:43: warning: large integer implicitly truncated to unsigned type
drivers/mmc/core/quirks.c:46: warning: large integer implicitly truncated to unsigned type
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The current mechanism is SDIO-only. This allows us to create
function-specific quirks, without creating messy Kconfig dependencies,
or polluting core/ with function-specific code.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
006ebd5d introduced sdio_disable_cd(), which disconnects the pull-up
resistor on CD/DAT[3] (pin 1) of the card.
Make it possible to start using sdio_disable_cd() by introducing
MMC_QUIRK_DISABLE_CD.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Introduce MMC_QUIRK_NONSTD_FUNC_IF to ignore the "SDIO Standard Function
interface code" as indicated by the card's FBR, and instead treat all
functions as non-standard interfaces.
This is required to prevent standard drivers from facing
errors when trying to communicate with SDIO cards that erroneously
indicate standard function interface codes.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
6b5eda36 followed SDIO spec part E1 section 8, which states that
in case SDIO interrupts are being used to wake up a suspended host,
then it is required to switch to 1-bit mode before stopping the clock.
Before switching to 1-bit mode (or back to 4-bit mode on resume),
make sure that SDIO interrupts are really being used to wake the host.
This is helpful for devices which have an external irq line (e.g.
wl1271), and do not use SDIO interrupts to wake up the host.
In this case, switching to 1-bit mode (and back to 4-bit mode on resume)
is not necessary.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Introduce a common function to handle large, contiguous kmalloc buffer
allocations by exponentially backing off on the size of the requested
kernel transfer buffer until it succeeds or until the requested
transfer buffer size falls below the page size.
This helps ensure the operation can succeed under low-memory, highly-
fragmented situations albeit somewhat more slowly.
Artem: so this patch solves the problem that the kernel tries to kmalloc too
large buffers, which (a) may fail and does fail - people complain about this,
and (b) slows down the system in case of high memory fragmentation, because
the kernel starts dropping caches, writing back, swapping, etc. But we do not
really have to allocate a lot of memory to do the I/O, we may do this even with
as little as one min. I/O unit (NAND page) of RAM. So the idea of this patch is
that if the user asks to read or write a lot, we try to kmalloc a lot, with GFP
flags which make the kernel _not_ drop caches, etc. If we can allocate it - good,
if not - we try to allocate twice as less, and so on, until we reach the min.
I/O unit size, which is our last resort allocation and use the normal
GFP_KERNEL flag.
Artem: re-write the allocation function so that it makes sure the allocated
buffer is aligned to the min. I/O size of the flash.
Signed-off-by: Grant Erickson <marathon96@gmail.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
mmc_card_is_powered_resumed is a mouthful; instead, simply use
mmc_card_keep_power, which also better explains the purpose of
the macro.
Employ mmc_card_keep_power() where possible.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Allows reliable writes to be used for MMC writes. Reliable writes are used
to service write REQ_FUA/REQ_META requests. Handles both the legacy and
the enhanced reliable write support in MMC cards.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
uBoot sometimes leaves eMMC pointing to the private boot partition.
Ensure we always start looking at the user partition.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Bruce Clemens <bpclemens@marvell.com>
Signed-off-by: Mark F. Brown <markb@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The NAND_USE_FLASH_BBT_NO_OOB and NAND_CREATE_EMPTY_BBT flags conflict
with the NAND_BBT_SCANBYTE1AND6 and NAND_BBT_DYNAMICSTRUCT flags,
respectively. This change will allow us to utilize these options
independently.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
* 'for-linus/2640/i2c' of git://git.fluff.org/bjdooks/linux: (21 commits)
mach-ux500: set proper I2C platform data from MOP500s
i2c-nomadik: break out single messsage transmission
i2c-nomadik: reset the hw after status check
i2c-nomadik: remove the unnecessary delay
i2c-nomadik: change the TX and RX threshold
i2c-nomadik: add code to retry on timeout failure
i2c-nomadik: use pm_runtime API
i2c-nomadik: print abort cause only on abort tag
i2c-nomadik: correct adapter timeout initialization
i2c-nomadik: remove the redundant error message
i2c-nomadik: corrrect returned error numbers
i2c-nomadik: fix speed enumerator
i2c-nomadik: make i2c timeout specific per i2c bus
i2c-nomadik: add regulator support
i2c: i2c-sh_mobile bus speed platform data V2
i2c: i2c-sh_mobile clock string removal
i2c-eg20t: Support new device ML7223 IOH
i2c: tegra: Add de-bounce cycles.
i2c: tegra: fix repeated start handling
i2c: tegra: recover from spurious interrupt storm
...
|
|
'for-2639/i2c-tegra' and 'for-2639/i2c-nomadik2' into for-linus/2640/i2c
|
|
Ooops I overlooked this one, and missing it causes compile
errors of the powerpc syscall.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: make plock operation killable
dlm: remove shared message stub for recovery
dlm: delayed reply message warning
dlm: Remove superfluous call to recalc_sigpending()
|
|
ssh://master.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (43 commits)
TOMOYO: Fix wrong domainname validation.
SELINUX: add /sys/fs/selinux mount point to put selinuxfs
CRED: Fix load_flat_shared_library() to initialise bprm correctly
SELinux: introduce path_has_perm
flex_array: allow 0 length elements
flex_arrays: allow zero length flex arrays
flex_array: flex_array_prealloc takes a number of elements, not an end
SELinux: pass last path component in may_create
SELinux: put name based create rules in a hashtable
SELinux: generic hashtab entry counter
SELinux: calculate and print hashtab stats with a generic function
SELinux: skip filename trans rules if ttype does not match parent dir
SELinux: rename filename_compute_type argument to *type instead of *con
SELinux: fix comment to state filename_compute_type takes an objname not a qstr
SMACK: smack_file_lock can use the struct path
LSM: separate LSM_AUDIT_DATA_DENTRY from LSM_AUDIT_DATA_PATH
LSM: split LSM_AUDIT_DATA_FS into _PATH and _INODE
SELINUX: Make selinux cache VFS RCU walks safe
SECURITY: Move exec_permission RCU checks into security modules
SELinux: security_read_policy should take a size_t not ssize_t
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: Make struct pcmcia_device_id const, sound drivers edition
staging: pcmcia: Convert pcmcia_device_id declarations to const
pcmcia: Convert pcmcia_device_id declarations to const
pcmcia: Make declaration and uses of struct pcmcia_device_id const
pcmcia/sa1100: put sa11x0_pcmcia_hw_init[] to .devinit.data
|
|
The DB8500 has ePOD:s (electronic power domains) which are possible
to switch on/off to deactivate silicon blocks on the DB8500 SoC
by cutting their power without retention. We model these as simple
regulators with one bit on/off settings.
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Martin Persson <martin.persson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds the DB5500 PRCMU driver. Right now this one is pretty
restricted in functionality, exposing a simple interface to send
I2C messages.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This updates the DB8500 PRCMU driver to the latest version
available internally. Nominally we would update the dependent
CPUfreq driver at the same time but since that is being moved
around in this patch set we postpone that by simply deactivating
it for the time being.
This is a snapshot of the current PRCMU firmware API as it looks
right now. The PRCMU firmware is still subject to change. This
also updates the CPUfreq driver to a newer version that will
utilize the new API.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Martin Persson <martin.persson@stericsson.com>
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Sebastien Rault <sebastien.rault@stericsson.com>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Based upon an email by Joe Perches.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
|
|
We have decided that this function arbiter fits better in the MFD
subsystem. Since we need to concatenate the split header files we move
it basically like this:
mv mach-ux500/prcmu-db8500.c drivers/mfd/db8500-prcmu.c
mv mach-ux500/include/mach/prcmu-defs.h include/linux/mfd/db8500-prcmu.h
mv mach-ux500/include/mach/prcmu-regs.h drivers/mfd/db8500-prcmu-regs.h
mach-ux500/include/mach/prcmu.h >> include/linux/mfd/db8500-prcmu.h
rm arch/arm/mach-ux500/include/mach/prcmu.h
Then we update different #include statements and Makefile orders etc
to make the PRCMU driver compile, link and boot in the new place
without really changing any code.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Fix new kernel-doc Error and Warning in <net/mac80211.h>:
Error(linux-2.6.39-git5/include/net/mac80211.h:550): cannot understand prototype: 'struct ieee80211_sched_scan_ies '
Warning(linux-2.6.39-git5/include/net/mac80211.h:2289): No description found for parameter 'sta'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix new kernel-doc warnings in <net/cfg80211.h>:
Warning(linux-2.6.39-git5/include/net/cfg80211.h:560): No description found for parameter 'bss_param'
Warning(linux-2.6.39-git5/include/net/cfg80211.h:1555): Enum value 'WIPHY_FLAG_SUPPORTS_SCHED_SCAN' not described in enum 'wiphy_flags'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (169 commits)
drivers/gpu/drm/radeon/atom.c: fix warning
drm/radeon/kms: bump kms version number
drm/radeon/kms: properly set num banks for fusion asics
drm/radeon/kms/atom: move dig phy init out of modesetting
drm/radeon/kms/cayman: fix typo in register mask
drm/radeon/kms: fix typo in spread spectrum code
drm/radeon/kms: fix tile_config value reported to userspace on cayman.
drm/radeon/kms: fix incorrect comparison in cayman setup code.
drm/radeon/kms: add wait idle ioctl for eg->cayman
drm/radeon/cayman: setup hdp to invalidate and flush when asked
drm/radeon/evergreen/btc/fusion: setup hdp to invalidate and flush when asked
agp/uninorth: Fix lockups with radeon KMS and >1x.
drm/radeon/kms: the SS_Id field in the LCD table if for LVDS only
drm/radeon/kms: properly set the CLK_REF bit for DCE3 devices
drm/radeon/kms: fixup eDP connector handling
drm/radeon/kms: bail early for eDP in hotplug callback
drm/radeon/kms: simplify hotplug handler logic
drm/radeon/kms: rewrite DP handling
drm/radeon/kms/atom: add support for setting DP panel mode
drm/radeon/kms: atombios.h updates for DP panel mode
...
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (29 commits)
[S390] cpu hotplug: fix external interrupt subclass mask handling
[S390] oprofile: dont access lowcore
[S390] oprofile: add missing irq stats counter
[S390] Ignore sendmmsg system call note wired up warning
[S390] s390,oprofile: fix compile error for !CONFIG_SMP
[S390] s390,oprofile: fix alert counter increment
[S390] Remove unused includes in process.c
[S390] get CPC image name
[S390] sclp: event buffer dissection
[S390] chsc: process channel-path-availability information
[S390] refactor page table functions for better pgste support
[S390] merge page_test_dirty and page_clear_dirty
[S390] qdio: prevent compile warning
[S390] sclp: remove unnecessary sendmask check
[S390] convert old cpumask API into new one
[S390] pfault: cleanup code
[S390] pfault: cpu hotplug vs missing completion interrupts
[S390] smp: add __noreturn attribute to cpu_die()
[S390] percpu: implement arch specific irqsafe_cpu_ops
[S390] vdso: disable gcov profiling
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (40 commits)
Input: ADP5589 - new driver for I2C Keypad Decoder and I/O Expander
Input: tsc2007 - add X, Y and Z fuzz factors to platform data
Input: tsc2007 - add poll_period parameter to platform data
Input: tsc2007 - add poll_delay parameter to platform data
Input: tsc2007 - add max_rt parameter to platform data
Input: tsc2007 - debounce pressure measurement
Input: ad714x - fix captouch wheel option algorithm
Input: ad714x - allow platform code to specify irqflags
Input: ad714x - fix threshold and completion interrupt masks
Input: ad714x - fix up input configuration
Input: elantech - remove support for proprietary X driver
Input: elantech - report multitouch with proper ABS_MT messages
Input: elantech - export pressure and width when supported
Input: elantech - describe further the protocol
Input: atmel_tsadcc - correct call to input_free_device
Input: add driver FSL MPR121 capacitive touch sensor
Input: remove useless synchronize_rcu() calls
Input: ads7846 - fix gpio_pendown configuration
Input: ads7846 - add possibility to use external vref on ads7846
Input: rotary-encoder - add support for half-period encoders
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
* 'for-2.6.40' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: Unify input section names
percpu: Avoid extra NOP in percpu_cmpxchg16b_double
percpu: Cast away printk format warning
percpu: Always align percpu output section to PAGE_SIZE
Fix up fairly trivial conflict in arch/x86/include/asm/percpu.h as per Tejun
|
|
If we are unable to locate an inode by ino, ask the MDS using the new
LOOKUPINO command.
Signed-off-by: Sage Weil <sage@newdream.net>
|
|
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: switch to dynamic printks
UBI: turn some macros into static inline
UBI: improve checking in debugging prints
UBI: fix typo in a message
UBI: fix minor stylistic issues
UBI: use __packed instead of __attribute__((packed))
UBI: cleanup comments around volume properties
UBI: re-name set volume properties ioctl
UBI: make the control character device non-seekable
|
|
Catch cases where dst_metric_set() and other functions are called
but _metrics is NULL.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts target core and follwing scsi-misc upstream fabric
modules to use include/scsi/scsi_tcq.h includes for SIMPLE, HEAD_OF_QUEUE
and ORDERED SCSI tasks instead of scsi/libsas.h with TASK_ATTR*
*) tcm_loop: Convert tcm_loop_allocate_core_cmd() + tcm_loop_device_reset() to
scsi_tcq.h
*) tcm_fc: Convert ft_send_cmd() from FCP_PTA_* to scsi_tcq.h
Reported-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
This patch converts transport_core_report_lun_response() to use
drivers/scsi/scsi_scan.c:int_to_scsilun instead of using the
struct target_core_fabric_ops->pack_lun() fabric provided API vector.
It also removes the tfo->pack_lun check from target_fabric_tf_ops_check()
and removes from struct target_core_fabric_ops->pack_lun() from
target_core_fabric_ops.h, and the following mainline scsi-misc fabric
modules:
*) tcm_loop: Drop tcm_loop_pack_lun() usage
*) tcm_fc: Drop ft_pack_lun() usage
Reported-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
This patch addresses a bug in the target core release path for HW
operation where transport_free_dev_tasks() was incorrectly being called
from transport_lun_remove_cmd() while releasing a se_cmd reference and
calling struct target_core_fabric_ops->queue_data_in().
This would result in a OOPs with HW target mode when the release of
se_task->task_sg[] would happen before pci_unmap_sg() can be called in
HW target mode fabric module code. This patch addresses the issue by
moving transport_free_dev_tasks() from transport_lun_remove_cmd() into
transport_generic_free_cmd(), and adding TRANSPORT_FREE_CMD_INTR and
transport_generic_free_cmd_intr() to allow se_cmd descriptor release
to happen fromfrom within transport_processing_thread() process context
when release of se_cmd is not possible from HW interrupt context.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
|
|
Provide a function which returns whether a transaction with given tid
will send a flush to the filesystem device. The function will be used
by ext4 to detect whether fsync needs to send a separate flush or not.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
|
In data=ordered mode, it's theoretically possible (however rare) that
an inode is filed to transaction's t_inode_list and a flusher thread
writes all the data and inode is reclaimed before the transaction
starts to commit. In such a case, we could erroneously omit sending a
flush to file system device when it is different from the journal
device (because data can still be in disk cache only).
Fix the problem by setting a flag in a transaction when some inode is added
to it and then send disk flush in the commit code when the flag is set.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
|
All static seqlock should be initialized with the lockdep friendly
__SEQLOCK_UNLOCKED() macro.
Remove legacy SEQLOCK_UNLOCKED() macro.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Link: http://lkml.kernel.org/r/%3C1306238888.3026.31.camel%40edumazet-laptop%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
for-linus
Conflicts:
lib/flex_array.c
security/selinux/avc.c
security/selinux/hooks.c
security/selinux/ss/policydb.c
security/smack/smack_lsm.c
Manually resolve conflicts.
Signed-off-by: James Morris <jmorris@namei.org>
|
|
|
|
fixes this build error on sparc64 (at least):
In file included from arch/sparc/include/asm/siginfo.h:19,
from include/linux/signal.h:5,
from include/linux/sched.h:73,
from arch/sparc/kernel/asm-offsets.c:13:
include/linux/compat.h:401: error: expected ')' before 'ctx_id'
include/linux/compat.h:406: error: expected ')' before 'ctx_id'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
|
|
As UML does no longer need asmregparm we can remove it.
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: namhyung@gmail.com
Cc: davem@davemloft.net
Cc: fweisbec@gmail.com
Cc: dhowells@redhat.com
Link: http://lkml.kernel.org/r/%3C1306189085-29896-1-git-send-email-richard%40nod.at%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Ben Nagy reported a scalability problem with KVM/QEMU that hit very hard
a single spinlock (idr_lock) in posix-timers code, on its 48 core
machine.
Even on a 16 cpu machine (2x4x2), a single test can show 98% of cpu time
used in ticket_spin_lock, from lock_timer
Ref: http://www.spinics.net/lists/kvm/msg51526.html
Switching to RCU is quite easy, IDR being already RCU ready. idr_lock
should be locked only for an insert/delete, not a lookup.
Benchmark on a 2x4x2 machine, 16 processes calling timer_gettime().
Before :
real 1m18.669s
user 0m1.346s
sys 1m17.180s
After :
real 0m3.296s
user 0m1.366s
sys 0m1.926s
Reported-by: Ben Nagy <ben@iagu.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Ben Nagy <ben@iagu.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Found these with the help of ispell -l.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
|
|
An administrative detach used to request a state change directly to D_DISKLESS,
first suspending IO to avoid the last put_ldev() occuring from an endio handler,
potentially in irq context.
This is not enough on the receiving side (typically secondary), we may miss
some peer_req on the way to local disk, which then may do the last put_ldev()
from their drbd_peer_request_endio().
This patch makes the detach always go through the intermediate D_FAILED state.
We may consider to rename it D_DETACHING.
Alternative approach would be to create yet an other work item to be scheduled
on the worker, do the destructor work from there, and get the timing right.
manually picked commit 564040f from the drbd 8.4 branch.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
For some time we contemplated calling the "struct lru_cache"
a "struct tracked_set", and some comments kept the ts_ prefix.
Fix those to match the member field names.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
|
|
|