| Age | Commit message (Collapse) | Author |
|---|
|
Nothing outside of the driver core needs to get to the deferred probe
pointer, so move it inside the private area of 'struct device' so no one
tries to mess around with it.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allow drivers to report at probe time that they cannot get all the resources
required by the device, and should be retried at a later time.
This should completely solve the problem of getting devices
initialized in the right order. Right now this is mostly handled by
mucking about with initcall ordering which is a complete hack, and
doesn't even remotely handle the case where device drivers are in
modules. This approach completely sidesteps the issues by allowing
driver registration to occur in any order, and any driver can request
to be retried after a few more other drivers get probed.
v4: - Integrate Manjunath's addition of a separate workqueue
- Change -EAGAIN to -EPROBE_DEFER for drivers to trigger deferral
- Update comment blocks to reflect how the code really works
v3: - Hold off workqueue scheduling until late_initcall so that the bulk
of driver probes are complete before we start retrying deferred devices.
- Tested with simple use cases. Still needs more testing though.
Using it to get rid of the gpio early_initcall madness, or to replace
the ASoC internal probe deferral code would be ideal.
v2: - added locking so it should no longer be utterly broken in that regard
- remove device from deferred list at device_del time.
- Still completely untested with any real use case, but has been
boot tested.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dilan Lee <dilee@nvidia.com>
Cc: Manjunath GKondaiah <manjunath.gkondaiah@linaro.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Traditionally, any System-on-Chip based platform creates a flat list
of platform_devices directly under /sys/devices/platform.
In order to give these some better structure, this introduces a new
bus type for soc_devices that are registered with the new
soc_device_register() function. All devices that are on the same
chip should then be registered as child devices of the soc device.
The soc bus also exports a few standardised device attributes which
allow user space to query the specific type of soc.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch introduces the module_pci_driver macro which is a convenience
macro for PCI driver modules similar to module_platform_driver. It is
intended to be used by drivers which init/exit section does nothing but
register/unregister the PCI driver. By using this macro it is possible
to eliminate a few lines of boilerplate code per PCI driver.
Based on work done by Lars-Peter Clausen <lars@metafoo.de> for other
busses (i2c and spi).
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now, cleanup the user/kernel KVP protocol by using the same structure
definition that is used for host/guest KVP protocol. This simplifies the code.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now cleanup the hyperv.h with regards to KVP definitions.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In preparation for consolidating all KVP related defines into a single header file
that both the kernel and user level components can use, move the contents of
hv_kvp.h into hyperv.h.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current KVP code carries some private connector related defines.
Update connector.h to have all the KVP defines. As part of this patch
get rid of some unused defines.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This was done to resolve a merge and build problem with the
drivers/acpi/processor_driver.c file.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are few important bug fixes for LogFS
* tag 'for-linus' of git://github.com/prasad-joshi/logfs_upstream:
Logfs: Allow NULL block_isbad() methods
logfs: Grow inode in delete path
logfs: Free areas before calling generic_shutdown_super()
logfs: remove useless BUG_ON
MAINTAINERS: Add Prasad Joshi in LogFS maintiners
logfs: Propagate page parameter to __logfs_write_inode
logfs: set superblock shutdown flag after generic sb shutdown
logfs: take write mutex lock during fsync and sync
logfs: Prevent memory corruption
logfs: update page reference count for pined pages
Fix up conflict in fs/logfs/dev_mtd.c due to semantic change in what
"mtd->block_isbad" means in commit f2933e86ad93: "Logfs: Allow NULL
block_isbad() methods" clashing with the abstraction changes in the
commits 7086c19d0742: "mtd: introduce mtd_block_isbad interface" and
d58b27ed58a3: "logfs: do not use 'mtd->block_isbad' directly".
This resolution takes the semantics from commit f2933e86ad93, and just
makes mtd_block_isbad() return zero (false) if the 'block_isbad'
function is NULL. But that also means that now "mtd_can_have_bb()"
always returns 0.
Now, "mtd_block_markbad()" will obviously return an error if the
low-level driver doesn't support bad blocks, so this is somewhat
non-symmetric, but it actually makes sense if a NULL "block_isbad"
function is considered to mean "I assume that all my blocks are always
good".
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Here are a bunch of USB patches for 3.3-rc1.
Nothing major, largest thing here is the removal of some drivers that
did not work at all. Other than that, the normal collection of bugfixes
and new device ids.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* tag 'usb-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (52 commits)
uwb & wusb: fix kconfig error
USB: Realtek cr: fix autopm scheduling while atomic
USB: ftdi_sio: Add more identifiers
xHCI: Cleanup isoc transfer ring when TD length mismatch found
usb: musb: omap2430: minor cleanups.
qcaux: add more Pantech UML190 and UML290 ports
Revert "drivers: usb: Fix dependency for USB_HWA_HCD"
usb: mv-otg - Fix build if CONFIG_USB is not set
USB: cdc-wdm: Avoid hanging on interface with no USB_CDC_DMM_TYPE
usb: add support for STA2X11 host driver
drivers: usb: Fix dependency for USB_HWA_HCD
kernel-doc: fix new warning in usb.h
USB: OHCI: fix new compiler warnings
usb: serial: kobil_sct: fix compile warning:
drivers/usb/host/ehci-fsl.c: add missing iounmap
USB: cdc-wdm: better allocate a buffer that is at least as big as we tell the USB core
USB: cdc-wdm: call wake_up_all to allow driver to shutdown on device removal
USB: cdc-wdm: use two mutexes to allow simultaneous read and write
USB: cdc-wdm: updating desc->length must be protected by spin_lock
USB: usbsevseg: fix max length
...
|
|
1) Setting link attributes can modify the size of the attributes that
would be reported on a subsequent getlink netlink operation,
therefore min_ifinfo_dump_size needs to be adjusted. From Stefan
Gula.
2) Resegmentation of TSO frames while trimming can violate invariants
expected by callers, namely that the number of segments can only stay
the same or decrease, never increase. If MSS changes, however, we
can trim data but then end up with more segments. Fix this by only
segmenting to the MSS already recorded in the SKB. That's the
simplest fix for now and if we want to get more fancy in the future
that's a more involved change.
This probably explains some retransmit counter inaccuracies.
From Neal Cardwell.
3) Fix too-many-wakeups in POLL with AF_UNIX sockets, from Eric Dumazet.
4) Fix CAIF crashes wrt. namespace handling. From Eric Dumazet and
Eric W. Biederman.
5) TCP port selection fixes from Flavio Leitner.
6) More socket memory cgroup build fixes in certain randonfig
situations. From Glauber Costa.
7) Fix TCP memory sysctl regression reported by Ingo Molnar, also from
Glauber Costa.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
af_unix: fix EPOLLET regression for stream sockets
tcp: fix tcp_trim_head() to adjust segment count with skb MSS
net/tcp: Fix tcp memory limits initialization when !CONFIG_SYSCTL
net caif: Register properly as a pernet subsystem.
netns: Fail conspicously if someone uses net_generic at an inappropriate time.
net: explicitly add jump_label.h header to sock.h
net: RTNETLINK adjusting values of min_ifinfo_dump_size
ipv6: Fix ip_gre lockless xmits.
xen-netfront: correct MAX_TX_TARGET calculation.
netns: fix net_alloc_generic()
tcp: bind() optimize port allocation
tcp: bind() fix autoselection to share ports
l2tp: l2tp_ip - fix possible oops on packet receive
iwlwifi: fix PCI-E transport "inta" race
mac80211: set bss_conf.idle when vif is connected
mac80211: update oper_channel on ibss join
|
|
sysctl_tcp_mem() initialization was moved to sysctl_tcp_ipv4.c
in commit 3dc43e3e4d0b52197d3205214fe8f162f9e0c334, since it
became a per-ns value.
That code, however, will never run when CONFIG_SYSCTL is
disabled, leading to bogus values on those fields - causing hung
TCP sockets.
This patch fixes it by keeping an initialization code in
tcp_init(). It will be overwritten by the first net namespace
init if CONFIG_SYSCTL is compiled in, and do the right thing if
it is compiled out.
It is also named properly as tcp_init_mem(), to properly signal
its non-sysctl side effect on TCP limits.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Glauber Costa <glommer@parallels.com>
Cc: David S. Miller <davem@davemloft.net>
Link: http://lkml.kernel.org/r/4F22D05A.8030604@parallels.com
[ renamed the function, tidied up the changelog a bit ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 2aede851ddf08666f68ffc17be446420e9d2a056
PM / Hibernate: Freeze kernel threads after preallocating memory
introduced a mechanism by which kernel threads were frozen after
the preallocation of hibernate image memory to avoid problems with
frozen kernel threads not responding to memory freeing requests.
However, it overlooked the s2disk code path in which the
SNAPSHOT_CREATE_IMAGE ioctl was run directly after SNAPSHOT_FREE,
which caused freeze_workqueues_begin() to BUG(), because it saw
that worqueues had been already frozen.
Although in principle this issue might be addressed by removing
the relevant BUG_ON() from freeze_workqueues_begin(), that would
reintroduce the very problem that commit 2aede851ddf08666f68ffc17be4
attempted to avoid into that particular code path. For this reason,
to fix the issue at hand, introduce thaw_kernel_threads() and make
the SNAPSHOT_FREE ioctl execute it.
Special thanks to Srivatsa S. Bhat for detailed analysis of the
problem.
Reported-and-tested-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: stable@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Here are some patches for the 3.3-rc1 tree.
It contains the removal of the sysdev code, now that all users of it are
gone, as well as some sysfs bugfixes that have been reported by users.
There are also some documentation updates here as well.
* tag 'driver-core-3.3-rc1-bugfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
sysfs: Complain bitterly about attempts to remove files from nonexistent directories.
stable: update documentation to ask for kernel version
base/core.c:fix typo in comment in function device_add
Documentation: devres: add allocation functions to list of supported calls
Documentation update for the driver model core
kernel-doc: fix new warnings in driver-core
kernel-doc: fix new warnings in debugfs
kernel-doc: fix new warnings in device.h
driver core: remove drivers/base/sys.c and include/linux/sysdev.h
|
|
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm: (31 commits)
ARM: 7304/1: ioremap: fix boundary check when reusing static mapping
ARM: 7301/1: Rename the T() macro to TUSER() to avoid namespace conflicts
ARM: 7299/1: ftrace: clear zero bit in reported IPs for Thumb-2
ARM: 7298/1: realview: fix mapping of MPCore private memory region
PCMCIA: fix sa1111 oops on remove
ARM: 7288/1: mach-sa1100: add missing module_init() call
ARM: 7297/1: smp_twd: make sure timer is stopped before registering it
ARM: 7296/1: proc-v7.S: remove HARVARD_CACHE preprocessor guards
ARM: 7295/1: cortex-a7: move proc_info out of !CONFIG_ARM_LPAE block
ARM: 7293/1: logical_cpu_map: decouple CPU mapping from SMP
ARM: 7291/1: cache: assume 64-byte L1 cachelines for ARMv7 CPUs
ARM: 7290/1: vmlinux.lds.S: align the exception fixup table to a 4-byte boundary
ARM: 7289/1: vmlinux.lds.S: do not hardcode cacheline size as 32 bytes
MFD: ucb1x00-ts: fix resume failure
MFD: ucb1x00-core: fix gpiolib direction_output handling
MFD: ucb1x00-core: fix missing restore of io output data on resume
MFD: mcp-core: fix mcp_priv() to be more type safe
MFD: mcp-core: fix complaints from the genirq layer
Revert "ARM: sa11x0: Implement autoloading of codec and codec pdata for mcp bus."
Revert "ARM: sa1100: Refactor mcp-sa11x0 to use platform resources."
...
Fix up conflict due to arch/arm/mach-mx5/Kconfig having been merged into
mach-imx5 (commit 784a90c0a7d8: "ARM i.MX: Merge i.MX5 support into
mach-imx"), but the ARM_L1_CACHE_SHIFT_6 entry was moved to be driven by
the CPU_V7 logic from it in the old location in rmk's branch (commit
a092f2b15399: "ARM: 7291/1: cache: assume 64-byte L1 cachelines for
ARMv7 CPUs").
|
|
By definition net_generic should never be called when it can return
NULL. Fail conspicously with a BUG_ON to make it clear when people mess
up that a NULL return should never happen.
Recently there was a bug in the CAIF subsystem where it was registered
with register_pernet_device instead of register_pernet_subsys. It was
erroneously concluded that net_generic could validly return NULL and
that net_assign_generic was buggy (when it was just inefficient).
Hopefully this BUG_ON will prevent people to coming to similar erroneous
conclusions in the futrue.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is based on Andi Kleen's work:
Implement autoprobing/loading of modules serving CPU
specific features (x86cpu autoloading).
And Kay Siever's work to get rid of sysdev cpu structures
and making use of struct device instead.
Before, the cpuid driver had to be loaded to get the x86cpu
autoloading feature. With this patch autoloading works through
the /sys/devices/system/cpu object
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Dave Jones <davej@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The only left over hole in automatic cpufreq driver loading was the loading
of ACPI cpufreq. This driver should be loaded when ACPI supports a _PDC
method and the CPU vendor wants to use acpi cpufreq.
Simply add a request module call to the acpi processor core driver
when this is true. This seems like the simplest solution for this.
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
There's a growing number of drivers that support a specific x86 feature
or CPU. Currently loading these drivers currently on a generic
distribution requires various driver specific hacks and it often
doesn't work.
This patch adds auto probing for drivers based on the x86 cpuid
information, in particular based on vendor/family/model number
and also based on CPUID feature bits.
For example a common issue is not loading the SSE 4.2 accelerated
CRC module: this can significantly lower the performance of BTRFS
which relies on fast CRC.
Another issue is loading the right CPUFREQ driver for the current CPU.
Currently distributions often try all all possible driver until
one sticks, which is not really a good way to do this.
It works with existing udev without any changes. The code
exports the x86 information as a generic string in sysfs
that can be matched by udev's pattern matching.
This scheme does not support numeric ranges, so if you want to
handle e.g. ranges of model numbers they have to be encoded
in ASCII or simply all models or families listed. Fixing
that would require changing udev.
Another issue is that udev will happily load all drivers that match,
there is currently no nice way to stop a specific driver from
being loaded if it's not needed (e.g. if you don't need fast CRC)
But there are not that many cpu specific drivers around and they're
all not that bloated, so this isn't a particularly serious issue.
Originally this patch added the modalias to the normal cpu
sysdevs. However sysdevs don't have all the infrastructure
needed for udev, so it couldn't really autoload drivers.
This patch instead adds the CPU modaliases to the cpuid devices,
which are real devices with full support for udev. This implies
that the cpuid driver has to be loaded to use this.
This patch just adds infrastructure, some driver conversions
in followups.
Thanks to Kay for helping with some sysfs magic.
v2: Constifcation, some updates
v4: (trenn@suse.de):
- Use kzalloc instead of kmalloc to terminate modalias buffer
- Use uppercase hex values to match correctly against hex values containing
letters
Cc: Dave Jones <davej@redhat.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Jen Axboe <axboe@kernel.dk>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Commit 36a1211970193ce215de50ed1e4e1272bc814df1 removed linux/module.h
include statement from one of the headers that end up in net/sock.h.
It was providing us with static_branch() definition implicitly, so
after its removal the build got broken.
To fix this, and avoid having this happening in the future,
let me do the right thing and include linux/jump_label.h
explicitly in sock.h.
Signed-off-by: Glauber Costa <glommer@parallels.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Add missing __cpuinit annotation in rcutorture code
sched: Add "const" to is_idle_task() parameter
rcu: Make rcutorture bool parameters really bool (core code)
memblock: Fix alloc failure due to dumb underflow protection in memblock_find_in_range_node()
|
|
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/ttm: fix two regressions since move_notify changes
drm/radeon: avoid deadlock if GPU lockup is detected in ib_pool_get
drm/radeon: silence out possible lock dependency warning
drm: Fix authentication kernel crash
gma500: Fix shmem mapping
drm/radeon/kms: refine TMDS dual link checks
drm/radeon/kms: use drm_detect_hdmi_monitor for picking encoder mode
drm/radeon/kms: rework modeset sequence for DCE41 and DCE5
drm/radeon/kms: move panel mode setup into encoder mode set
drm/radeon/kms: move disp eng pll setup to init path
drm/radeon: finish getting bios earlier
drm/radeon: fix invalid memory access in radeon_atrm_get_bios()
drm/radeon/kms: add some missing semaphore init
drm/radeon/kms: Add an MSI quirk for Dell RS690
gpu, drm, sis: Don't return uninitialized variable from sis_driver_load()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
* 'for-greg' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: musb: omap2430: minor cleanups.
usb: dwc3: unmap the proper number of sg entries
usb: musb: fix shutdown while usb gadget is in use
usb: gadget: f_mass_storage: Use "bool" instead of "int" in fsg_module_parameters
usb: gadget: check for streams only for SS udcs
usb: gadget: fsl_udc: fix the usage of udc->max_ep
drivers: usb: otg: Fix dependencies for some OTG drivers
usb: renesas: silence uninitialized variable report in usbhsg_recip_run_handle()
usb: gadget: SS Isoc endpoints use comp_desc->bMaxBurst too
usb: gadget: storage: endian fix
usb: dwc3: ep0: fix compile warning
usb: musb: davinci: fix build breakage
usb: gadget: langwell: don't call gadget's disconnect()
usb: gadget: langwell: drop langwell_otg support
usb: otg: kill langwell_otg driver
usb: dwc3: ep0: tidy up Pending Request handling
|
|
If the master tries to authenticate a client using drm_authmagic and
that client has already closed its drm file descriptor,
either wilfully or because it was terminated, the
call to drm_authmagic will dereference a stale pointer into kmalloc'ed memory
and corrupt it.
Typically this results in a hard system hang.
This patch fixes that problem by removing any authentication tokens
(struct drm_magic_entry) open for a file descriptor when that file
descriptor is closed.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Quoth Len:
"This fixes a merge-window regression due to a conflict
between error injection and preparation to remove atomicio.c
Here we fix that regression and complete the removal
of atomicio.c.
This also re-orders some idle initialization code to
complete the merge window series that allows cpuidle
to cope with bringing processors on-line after boot."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
Use acpi_os_map_memory() instead of ioremap() in einj driver
ACPI, APEI, EINJ, cleanup 0 vs NULL confusion
ACPI, APEI, EINJ Allow empty Trigger Error Action Table
thermal: Rename generate_netlink_event
ACPI / PM: Add Sony Vaio VPCCW29FX to nonvs blacklist.
ACPI: Remove ./drivers/acpi/atomicio.[ch]
ACPI, APEI: Add RAM mapping support to ACPI
ACPI, APEI: Add 64-bit read/write support for APEI on i386
ACPI processor hotplug: Delay acpi_processor_start() call for hotplugged cores
ACPI processor hotplug: Split up acpi_processor_add
|
|
Now that there are no users of get_driver() or put_driver(), this
patch (as1513) removes those routines completely.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Davem says:
1) Fix JIT code generation on x86-64 for divide by zero, from Eric Dumazet.
2) tg3 header length computation correction from Eric Dumazet.
3) More build and reference counting fixes for socket memory cgroup
code from Glauber Costa.
4) module.h snuck back into a core header after all the hard work we
did to remove that, from Paul Gortmaker and Jesper Dangaard Brouer.
5) Fix PHY naming regression and add some new PCI IDs in stmmac, from
Alessandro Rubini.
6) Netlink message generation fix in new team driver, should only advertise
the entries that changed during events, from Jiri Pirko.
7) SRIOV VF registration and unregistration fixes, and also add a
missing PCI ID, from Roopa Prabhu.
8) Fix infinite loop in tx queue flush code of brcmsmac, from Stanislaw Gruszka.
9) ftgmac100/ftmac100 build fix, missing interrupt.h include.
10) Memory leak fix in net/hyperv do_set_mutlicast() handling, from Wei Yongjun.
11) Off by one fix in netem packet scheduler, from Vijay Subramanian.
12) TCP loss detection fix from Yuchung Cheng.
13) TCP reset packet MD5 calculation uses wrong address, fix from Shawn Lu.
14) skge carrier assertion and DMA mapping fixes from Stephen Hemminger.
15) Congestion recovery undo performed at the wrong spot in BIC and CUBIC
congestion control modules, fix from Neal Cardwell.
16) Ethtool ETHTOOL_GSSET_INFO is unnecessarily restrictive, from Michał Mirosław.
17) Fix triggerable race in ipv6 sysctl handling, from Francesco Ruggeri.
18) Statistics bug fixes in mlx4 from Eugenia Emantayev.
19) rds locking bug fix during info dumps, from your's truly.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
rds: Make rds_sock_lock BH rather than IRQ safe.
netprio_cgroup.h: dont include module.h from other includes
net: flow_dissector.c missing include linux/export.h
team: send only changed options/ports via netlink
net/hyperv: fix possible memory leak in do_set_multicast()
drivers/net: dsa/mv88e6xxx.c files need linux/module.h
stmmac: added PCI identifiers
llc: Fix race condition in llc_ui_recvmsg
stmmac: fix phy naming inconsistency
dsa: Add reporting of silicon revision for Marvell 88E6123/88E6161/88E6165 switches.
tg3: fix ipv6 header length computation
skge: add byte queue limit support
mv643xx_eth: Add Rx Discard and Rx Overrun statistics
bnx2x: fix compilation error with SOE in fw_dump
bnx2x: handle CHIP_REVISION during init_one
bnx2x: allow user to change ring size in ISCSI SD mode
bnx2x: fix Big-Endianess in ethtool -t
bnx2x: fixed ethtool statistics for MF modes
bnx2x: credit-leakage fixup on vlan_mac_del_all
macvlan: fix a possible use after free
...
|
|
A considerable effort was invested in wiping out module.h
from being present in all the other standard includes. This
one leaked back in, but once again isn't strictly necessary,
so remove it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes event message behaviour to send only updated records
instead of whole list. This fixes bug on which userspace receives non-actual
data in case multiple events occur in row.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
lineno:24 allows files with 4 million lines, an insane file-size, even
for never-to-get-in-tree machine generated code. Reduce this to 18
bits, which still allows 256k lines. This is still insanely big, but
its not raving mad.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Change describe_flags() to emit '=[pmflt_]+' for current callsite
flags, or just '=_' when they're disabled. Having '=' in output
allows a more selective grep expression; in contrast '-' may appear
in filenames, line-ranges, and format-strings. '=' also has better
mnemonics, saying; "the current setting is equal to <flags>".
This allows grep "=_" <dbgfs>/dynamic_debug/control to see disabled
callsites while avoiding the many occurrences of " = " seen in format
strings.
Enlarge flagsbufs to handle additional flag char, and alter
ddebug_parse_flags() to allow flags=0, so that user can turn off all
debug flags via:
~# echo =_ > <dbgfs>/dynamic_debug/control
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If CONFIG_DYNAMIC_DEBUG is defined, honor it over DEBUG, so that
pr_debug()s are controllable, instead of always-on. When DEBUG is
also defined, change _DPRINTK_FLAGS_DEFAULT to enable printing by
default.
Also adding _DPRINTK_FLAGS_INCL_MODNAME would be nice, but there are
numerous cases of pr_debug(NAME ": ...), which would result in double
printing of module-name. So defer this until things settle.
Cc: David Miller <davem@davemloft.net>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Currently any enabled dynamic-debug flag on a pr_debug callsite will
enable printing, even if _DPRINTK_FLAGS_PRINT is off. Checking print
flag directly allows "-p" to disable callsites without fussing with
other flags, so the following disables everything, without altering
flags user may have set:
echo -p > $DBGFS/dynamic_debug/control
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix new kernel-doc warning:
Warning(include/linux/usb.h:1251): No description found for parameter 'num_mapped_sgs'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
quota: Pass information that quota is stored in system file to userspace
ext2: protect inode changes in the SETVERSION and SETFLAGS ioctls
jbd: Issue cache flush after checkpointing
|
|
Fix new kernel-doc warnings:
Warning(include/linux/device.h:299): No description found for parameter 'name'
Warning(include/linux/device.h:299): No description found for parameter 'subsys'
Warning(include/linux/device.h:299): No description found for parameter 'node'
Warning(include/linux/device.h:299): No description found for parameter 'add_dev'
Warning(include/linux/device.h:299): No description found for parameter 'remove_dev'
Warning(include/linux/device.h:685): No description found for parameter 'id'
Warning(include/linux/device.h:1009): No description found for parameter '__driver'
Warning(include/linux/device.h:1009): No description found for parameter '__register'
Warning(include/linux/device.h:1009): No description found for parameter '__unregister'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The way this driver was added by f0ae849 (usb: Add Intel Langwell USB
OTG Transceiver Driver) never even compiled together with langwell_udc,
and that's the only way for it to be useful.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: stable@vger.kernel.org # v2.6.31+
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
so move its include into fs.h inside the __KERNEL__ protection.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
'thermal-netlink' into release
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Power management fixes for 3.3
Two fixes for regressions introduced during the merge window, one fix for
a long-standing obscure issue in the computation of hibernate image size
and two small PM documentation fixes.
* tag 'pm-fixes-for-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Sleep: Fix read_unlock_usermodehelper() call.
PM / Hibernate: Rewrite unlock_system_sleep() to fix s2disk regression
PM / Hibernate: Correct additional pages number calculation
PM / Documentation: Fix minor issue in freezing_of_tasks.txt
PM / Documentation: Fix spelling mistake in basic-pm-debugging.txt
|
|
The usual kernel-doc fixups from Randy. Some of them David acked as
merged in his tree, this is the random left-overs.
* kernel-doc:
docbook: fix sched source file names in device-drivers book
docbook: change iomap source filename in deviceiobook
docbook: don't use serial_core.h in device-drivers book
kernel-doc: fix kernel-doc warnings in sched
kernel-doc: fix new warnings in cfg80211.h
kernel-doc: fix new warning in usb.h
kernel-doc: fix new warnings in device.h
kernel-doc: fix new warnings in debugfs
kernel-doc: fix new warning in regulator core
kernel-doc: fix new warnings in pci
kernel-doc: fix new warnings in driver-core
kernel-doc: fix new warnings in auditsc.c
scripts/kernel-doc: fix fatal error caused by cfg80211.h
|
|
Quoth Andrew:
"Random fixes. And a simple new LED driver which I'm trying to sneak
in while you're not looking."
Sneaking successful.
* akpm:
score: fix off-by-one index into syscall table
mm: fix rss count leakage during migration
SHM_UNLOCK: fix Unevictable pages stranded after swap
SHM_UNLOCK: fix long unpreemptible section
kdump: define KEXEC_NOTE_BYTES arch specific for s390x
mm/hugetlb.c: undo change to page mapcount in fault handler
mm: memcg: update the correct soft limit tree during migration
proc: clear_refs: do not clear reserved pages
drivers/video/backlight/l4f00242t03.c: return proper error in l4f00242t03_probe if regulator_get() fails
drivers/video/backlight/adp88x0_bl.c: fix bit testing logic
kprobes: initialize before using a hlist
ipc/mqueue: simplify reading msgqueue limit
leds: add led driver for Bachmann's ot200
mm: __count_immobile_pages(): make sure the node is online
mm: fix NULL ptr dereference in __count_immobile_pages
mm: fix warnings regarding enum migrate_mode
|
|
* git://git.samba.org/sfrench/cifs-2.6:
CIFS: Rename *UCS* functions to *UTF16*
[CIFS] ACL and FSCACHE support no longer EXPERIMENTAL
[CIFS] Fix build break with multiuser patch when LANMAN disabled
cifs: warn about impending deprecation of legacy MultiuserMount code
cifs: fetch credentials out of keyring for non-krb5 auth multiuser mounts
cifs: sanitize username handling
keys: add a "logon" key type
cifs: lower default wsize when unix extensions are not used
cifs: better instrumentation for coalesce_t2
cifs: integer overflow in parse_dacl()
cifs: Fix sparse warning when calling cifs_strtoUCS
CIFS: Add descriptions to the brlock cache functions
|
|
Fix new kernel-doc notation warnings:
Warning(include/linux/sched.h:2094): No description found for parameter 'p'
Warning(include/linux/sched.h:2094): Excess function parameter 'tsk' description in 'is_idle_task'
Warning(kernel/sched/cpupri.c:139): No description found for parameter 'newpri'
Warning(kernel/sched/cpupri.c:139): Excess function parameter 'pri' description in 'cpupri_set'
Warning(kernel/sched/cpupri.c:208): Excess function parameter 'bootmem' description in 'cpupri_init'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix new kernel-doc warnings:
Warning(include/net/cfg80211.h:1165): No description found for parameter 'channel_type'
Warning(include/net/cfg80211.h:2090): No description found for parameter 'probe_resp_offload'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix new kernel-doc warning:
Warning(include/linux/usb.h:1251): No description found for parameter 'num_mapped_sgs'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix new kernel-doc warnings:
Warning(include/linux/device.h:299): No description found for parameter 'name'
Warning(include/linux/device.h:299): No description found for parameter 'subsys'
Warning(include/linux/device.h:299): No description found for parameter 'node'
Warning(include/linux/device.h:299): No description found for parameter 'add_dev'
Warning(include/linux/device.h:299): No description found for parameter 'remove_dev'
Warning(include/linux/device.h:685): No description found for parameter 'id'
Warning(include/linux/device.h:1009): No description found for parameter '__driver'
Warning(include/linux/device.h:1009): No description found for parameter '__register'
Warning(include/linux/device.h:1009): No description found for parameter '__unregister'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit cc39c6a9bbde ("mm: account skipped entries to avoid looping in
find_get_pages") correctly fixed an infinite loop; but left a problem
that find_get_pages() on shmem would return 0 (appearing to callers to
mean end of tree) when it meets a run of nr_pages swap entries.
The only uses of find_get_pages() on shmem are via pagevec_lookup(),
called from invalidate_mapping_pages(), and from shmctl SHM_UNLOCK's
scan_mapping_unevictable_pages(). The first is already commented, and
not worth worrying about; but the second can leave pages on the
Unevictable list after an unusual sequence of swapping and locking.
Fix that by using shmem_find_get_pages_and_swap() (then ignoring the
swap) instead of pagevec_lookup().
But I don't want to contaminate vmscan.c with shmem internals, nor
shmem.c with LRU locking. So move scan_mapping_unevictable_pages() into
shmem.c, renaming it shmem_unlock_mapping(); and rename
check_move_unevictable_page() to check_move_unevictable_pages(), looping
down an array of pages, oftentimes under the same lock.
Leave out the "rotate unevictable list" block: that's a leftover from
when this was used for /proc/sys/vm/scan_unevictable_pages, whose flawed
handling involved looking at pages at tail of LRU.
Was there significance to the sequence first ClearPageUnevictable, then
test page_evictable, then SetPageUnevictable here? I think not, we're
under LRU lock, and have no barriers between those.
Signed-off-by: Hugh Dickins <hughd@google.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michel Lespinasse <walken@google.com>
Cc: <stable@vger.kernel.org> [back to 3.1 but will need respins]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
kdump only allocates memory for the prstatus ELF note. For s390x,
besides of prstatus multiple ELF notes for various different register
types are stored. Therefore the currently allocated memory is not
sufficient. With this patch the KEXEC_NOTE_BYTES macro can be defined
by architecture code and for s390x it is set to the correct size now.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
