| Age | Commit message (Collapse) | Author |
|---|
|
also update the clk definitions in pxa27x and pxa3xx.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Changes include:
1. rename MFP_LPM_WAKEUP_ENABLE into MFP_LPM_CAN_WAKEUP to indicate
the board capability of this pin to wakeup the system
2. add gpio_set_wake() and keypad_set_wake() to allow dynamically
enable/disable wakeup from GPIOs and keypad GPIO
* these functions are currently kept in mfp-pxa2xx.c due to their
dependency to the MFP configuration
3. pxa2xx_mfp_config() only gives early warning if MFP_LPM_CAN_WAKEUP
is set on incorrect pins
So that the GPIO's wakeup capability is now decided by the following:
a) processor's capability: (only those GPIOs which have dedicated
bits within PWER/PRER/PFER can wakeup the system), this is
initialized by pxa{25x,27x}_init_mfp()
b) board design decides:
- whether the pin is designed to wakeup the system (some of
the GPIOs are configured as other functions, which is not
intended to be a wakeup source), by OR'ing the pin config
with MFP_LPM_CAN_WAKEUP
- which edge the pin is designed to wakeup the system, this
may depends on external peripherals/connections, which is
totally board specific; this is indicated by MFP_LPM_EDGE_*
c) the corresponding device's (most likely the gpio_keys.c) wakeup
attribute:
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs. A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.
A pin configuration on pxa{25x,27x} is composed of:
- alternate function selection (or pin mux as commonly called)
- low power state or sleep state
- wakeup enabling from low power mode
The following MFP_xxx bit definitions in mfp.h are re-used:
- MFP_PIN(x)
- MFP_AFx
- MFP_LPM_DRIVE_{LOW, HIGH}
- MFP_LPM_EDGE_*
Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:
- MFP_CFG_IN : for input alternate functions
- MFP_CFG_OUT : for output alternate functions
Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT(). As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.
Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output. The actual
direction of the GPIO is configured by gpio_direction_{input, output}
Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.
E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:
enable_irq_wake( gpio_to_irq(35) );
To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).
Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:
- MFP_LPM_WAKEUP_ENABLE
The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:
- WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
- WAKEUP_ON_LEVEL_HIGH
The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.
These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.
The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
two reasons:
1. GPIO namings and their mode definitions are conceptually not part
of the PXA register definitions
2. this is actually a temporary move in the transition of PXA2xx to
use MFP-alike APIs (as what PXA3xx is now doing), so that legacy
code will still work and new code can be added in step by step
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This makes the code better organized and simplified a bit. The change
will lose a bit of performance when performing IRQ ack/mask/unmask,but
that's not too much after checking the result binary.
This patch also removes the ugly #ifdef CONFIG_PXA27x .. #endif by
carefully not to access those pxa{27x,3xx} specific registers, this
is done by keeping an internal IRQ number variable. The pxa-regs.h
is also modified so registers for IRQ > PXA_IRQ(31) are made public
even if CONFIG_PXA{27x,3xx} isn't defined (for pxa25x's sake)
The incorrect assumption in the original code that internal irq starts
from 0 is also corrected by comparing with PXA_IRQ(0).
"struct sys_device" for the IRQ are reduced into one single device on
pxa{27x,3xx}.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Enhanced GPIO alternate functions descriptions,
taken from Intel PXA270 Developers Manual.
Signed-off-by: Robert Jarzmik <rjarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Expose control of the PXA3xx 13MHz CLK_POUT pin via the clock API
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: Fix cut-and-paste error in rtl8150.c
USB: ehci: stop vt6212 bus hogging
USB: sierra: add another device id
USB: sierra: dma fixes
USB: add support for Motorola ROKR Z6 cellphone in mass storage mode
USB: isd200: fix memory leak in isd200_get_inquiry_data
USB: pl2303: another product ID
USB: new quirk flag to avoid Set-Interface
USB: fix gadgetfs class request delegation
|
|
Revert as it is reported to cause problems for people.
commit 4348a2dc49f9baecd34a9b0904245488c6189398
Author: Shaohua Li <shaohua.li@intel.com>
Date: Wed Oct 24 10:45:08 2007 +0800
pcie: utilize pcie transaction pending bit
PCIE has a mechanism to wait for Non-Posted request to complete. I think
pci_disable_device is a good place to do this.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to the regression reported at
http://bugzilla.kernel.org/show_bug.cgi?id=10065
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Soeren Sonnenburg <kernel@nn7.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Motorola ROKR Z6 cellphone has bugs in its USB, so it is impossible to use
it as mass storage. Patch describes new "unusual" USB device for it with
FIX_INQUIRY and FIX_CAPACITY flags and new BULK_IGNORE_TAG flag.
Last flag relaxes check for equality of bcs->Tag and us->tag in
usb_stor_Bulk_transport routine.
Signed-off-by: Constantin Baranov <const@tltsu.ru>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1057) fixes a problem with the X-Rite/Gretag-Macbeth
Eye-One Pro display colorimeter; the device crashes when it receives a
Set-Interface request. A new quirk (USB_QUIRK_NO_SET_INTF) is
introduced and a quirks entry is created for this device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Implement ata_qc_raw_nbytes() which determines the raw user-requested
size of a PC command.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: exec PT_DTRACE
[SPARC64]: Use shorter list_splice_init() for brevity.
[SPARC64]: Remove most limitations to kernel image size.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
sch_htb: fix "too many events" situation
connector: convert to single-threaded workqueue
[ATM]: When proc_create() fails, do some error handling work and return -ENOMEM.
[SUNGEM]: Fix NAPI assertion failure.
BNX2X: prevent ethtool from setting port type
[9P] net/9p/trans_fd.c: remove unused variable
[IPV6] net/ipv6/ndisc.c: remove unused variable
[IPV4] fib_trie: fix warning from rcu_assign_poinger
[TCP]: Let skbs grow over a page on fast peers
[DLCI]: Fix tiny race between module unload and sock_ioctl.
[SCTP]: Fix build warnings with IPV6 disabled.
[IPV4]: Fix null dereference in ip_defrag
|
|
It appears that 64-bit PCI resources cannot possibly ever have worked on
x86-32 even when the RESOURCES_64BIT config option was set, because any
driver that tried to [pci_]ioremap() the resource would have been unable
to do so because the high 32 bits would have been silently dropped on
the floor by the ioremap() routines that only used "unsigned long".
Change them to use "resource_size_t" instead, which properly encodes the
whole 64-bit resource data if RESOURCES_64BIT is enabled.
Acked-by: H. Peter Anvin <hpa@kernel.org>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: revert: reserve dma32 early for gart
|
|
Increase the number of PnP memory resources from 12 to 24.
This removes an "exceeded the max num of mem resources" warning on boot. I
also noticed the reservation of two more iomem ranges on the computer on
which this was tested.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Revert
commit f62f1fc9ef94f74fda2b456d935ba2da69fa0a40
Author: Yinghai Lu <yhlu.kernel@gmail.com>
Date: Fri Mar 7 15:02:50 2008 -0800
x86: reserve dma32 early for gart
The patch has a dependency on bootmem modifications which are not .25
material that late in the -rc cycle. The problem which is addressed by
the patch is limited to machines with 256G and more memory booted with
NUMA disabled. This is not a .25 regression and the audience which is
affected by this problem is very limited, so it's safer to do the
revert than pulling in intrusive bootmem changes right now.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Currently kernel images are limited to 8MB in size, and this causes
problems especially when enabling features that take up a lot of
kernel image space such as lockdep.
The code now will align the kernel image size up to 4MB and map that
many locked TLB entries. So, the only practical limitation is the
number of available locked TLB entries which is 16 on Cheetah and 64
on pre-Cheetah sparc64 cpus. Niagara cpus don't actually have hw
locked TLB entry support. Rather, the hypervisor transparently
provides support for "locked" TLB entries since it runs with physical
addressing and does the initial TLB miss processing.
Fully utilizing this change requires some help from SILO, a patch for
which will be submitted to the maintainer. Essentially, SILO will
only currently map up to 8MB for the kernel image and that needs to be
increased.
Note that neither this patch nor the SILO bits will help with network
booting. The openfirmware code will only map up to a certain amount
of kernel image during a network boot and there isn't much we can to
about that other than to implemented a layered network booting
facility. Solaris has this, and calls it "wanboot" and we may
implement something similar at some point.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduced by 270637abff0cdf848b910b9f96ad342e1da61c66
("[SCTP]: Fix a race between module load and protosw access")
Reported by Gabriel C:
In file included from net/sctp/sm_statetable.c:50:
include/net/sctp/sctp.h: In function 'sctp_v6_pf_init':
include/net/sctp/sctp.h:392: warning: 'return' with a value, in function returning void
In file included from net/sctp/sm_statefuns.c:62:
include/net/sctp/sctp.h: In function 'sctp_v6_pf_init':
include/net/sctp/sctp.h:392: warning: 'return' with a value, in function returning void
...
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched-devel
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mingo/linux-2.6-sched-devel:
sched: add arch_update_cpu_topology hook.
sched: add exported arch_reinit_sched_domains() to header file.
sched: remove double unlikely from schedule()
sched: cleanup old and rarely used 'debug' features.
|
|
Fix wrong function name and references to non-x86 architectures.
Signed-off-by: Matti Linnanvuori mattilinnanvuori@yahoo.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
fix the bug reported here:
http://bugzilla.kernel.org/show_bug.cgi?id=10232
use update_memory_range() instead of add_memory_range() directly
to avoid closing the gap.
( the new code only affects and runs on systems where the MTRR
workaround triggers. )
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
a system with 256 GB of RAM, when NUMA is disabled crashes the
following way:
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Cannot allocate aperture memory hole (ffff8101c0000000,65536K)
Kernel panic - not syncing: Not enough memory for aperture
Pid: 0, comm: swapper Not tainted 2.6.25-rc4-x86-latest.git #33
Call Trace:
[<ffffffff84037c62>] panic+0xb2/0x190
[<ffffffff840381fc>] ? release_console_sem+0x7c/0x250
[<ffffffff847b1628>] ? __alloc_bootmem_nopanic+0x48/0x90
[<ffffffff847b0ac9>] ? free_bootmem+0x29/0x50
[<ffffffff847ac1f7>] gart_iommu_hole_init+0x5e7/0x680
[<ffffffff847b255b>] ? alloc_large_system_hash+0x16b/0x310
[<ffffffff84506a2f>] ? _etext+0x0/0x1
[<ffffffff847a2e8c>] pci_iommu_alloc+0x1c/0x40
[<ffffffff847ac795>] mem_init+0x45/0x1a0
[<ffffffff8479ff35>] start_kernel+0x295/0x380
[<ffffffff8479f1c2>] _sinittext+0x1c2/0x230
the root cause is : memmap PMD is too big,
[ffffe200e0600000-ffffe200e07fffff] PMD ->ffff81383c000000 on node 0
almost near 4G..., and vmemmap_alloc_block will use up the ram under 4G.
solution will be:
1. make memmap allocation get memory above 4G...
2. reserve some dma32 range early before we try to set up memmap for all.
and release that before pci_iommu_alloc, so gart or swiotlb could get some
range under 4g limit for sure.
the patch is using method 2.
because method1 may need more code to handle SPARSEMEM and SPASEMEM_VMEMMAP
will get
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000
Memory: 264245736k/268959744k available (8484k kernel code, 4187464k reserved, 4004k data, 724k init)
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Clean up: eliminate some compiler noise on x86 when building with strict
warnings enabled, introduced by commit 345b904c.
In file included from include2/asm/thread_info_64.h:12,
from include2/asm/thread_info.h:4,
from
/home/cel/src/linux/nfs-2.6/include/linux/thread_info.h:35,
from
/home/cel/src/linux/nfs-2.6/include/linux/preempt.h:9,
from
/home/cel/src/linux/nfs-2.6/include/linux/spinlock.h:49,
from /home/cel/src/linux/nfs-2.6/include/linux/mmzone.h:7,
from /home/cel/src/linux/nfs-2.6/include/linux/gfp.h:4,
from /home/cel/src/linux/nfs-2.6/include/linux/slab.h:14,
from /home/cel/src/linux/nfs-2.6/fs/nfsd/nfs4acl.c:40:
include2/asm/page.h:55: warning: `inline' is not at beginning of
declaration
include2/asm/page.h:61: warning: `inline' is not at beginning of
declaration
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
mm/slub.c: In function 'slab_alloc':
mm/slub.c:1637: warning: assignment makes pointer from integer without a cast
mm/slub.c:1637: warning: assignment makes pointer from integer without a cast
mm/slub.c: In function 'slab_free':
mm/slub.c:1796: warning: assignment makes pointer from integer without a cast
mm/slub.c:1796: warning: assignment makes pointer from integer without a cast
A cast is needed in the 386 and 486 code because the type is a pointer. In
every other integer case the original cmpxchg code (and the cmpxchg_local
which has been copied from it) worked fine, but since we touch a pointer,
the type needs to be casted in the cmpxchg_local and cmpxchg macros.
The more recent code (586+) does not have this problem (the cast is already
there).
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Will be called each time the scheduling domains are rebuild.
Needed for architectures that don't have a static cpu topology.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Needed so it can be called from outside of sched.c.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix atomic backoff limit.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (46 commits)
[NET] ifb: set separate lockdep classes for queue locks
[IPV6] KCONFIG: Fix description about IPV6_TUNNEL.
[TCP]: Fix shrinking windows with window scaling
netpoll: zap_completion_queue: adjust skb->users counter
bridge: use time_before() in br_fdb_cleanup()
[TG3]: Fix build warning on sparc32.
MAINTAINERS: bluez-devel is subscribers-only
audit: netlink socket can be auto-bound to pid other than current->pid (v2)
[NET]: Fix permissions of /proc/net
[SCTP]: Fix a race between module load and protosw access
[NETFILTER]: ipt_recent: sanity check hit count
[NETFILTER]: nf_conntrack_h323: logical-bitwise & confusion in process_setup()
[RT2X00] drivers/net/wireless/rt2x00/rt2x00dev.c: remove dead code, fix warning
[IPV4]: esp_output() misannotations
[8021Q]: vlan_dev misannotations
xfrm: ->eth_proto is __be16
[IPV4]: ipv4_is_lbcast() misannotations
[SUNRPC]: net/* NULL noise
[SCTP]: fix misannotated __sctp_rcv_asconf_lookup()
[PKT_SCHED]: annotate cls_u32
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.25:
sh: Use relative paths for mach/cpu symlinks.
SH: Use newer, non-deprecated __SPIN_LOCK_UNLOCKED macro.
sh: Fix more user header breakage from sh64 integration.
sh: Fix uImage build error.
sh: Fix up the timer IRQ definition for SH7203.
sh: Fix up the address error exception handler for SH-2.
serial: sh-sci: Fix fifo stall on SH7760/SH7780/SH7785 SCIF.
|
|
There is a race is SCTP between the loading of the module
and the access by the socket layer to the protocol functions.
In particular, a list of addresss that SCTP maintains is
not initialized prior to the registration with the protosw.
Thus it is possible for a user application to gain access
to SCTP functions before everything has been initialized.
The problem shows up as odd crashes during connection
initializtion when we try to access the SCTP address list.
The solution is to refactor how we do registration and
initialize the lists prior to registering with the protosw.
Care must be taken since the address list initialization
depends on some other pieces of SCTP initialization. Also
the clean-up in case of failure now also needs to be refactored.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4872/1: Replaces buggy macro in S3C2410 irq include
[ARM] 4870/1: fix signal return code when enable CONFIG_OABI_COMPAT
[ARM] 4869/1: ARM: OMAP: Fix compile for mcbsp
[ARM] 4865/1: Register the F75375 device in the GLAN Tank platform code
[ARM] 4864/1: Enable write buffer coalescing on IOP
[ARM] 4863/1: AT91: CAP9 USART definitions for early debug
[ARM] 4861/1: AT91: Update maintainer email address (again)
ARM: OMAP1: Fix typo in OMAP1 MPU clock source initialization
ARM: OMAP: Fix DMA CLINK mask, clear spurious interrupt
ARM: OMAP: Fix chain_a_transfer return value
ARM: OMAP: Fix missing makefile options
ARM: OMAP: Fix GPIO IRQ unmask
ARM: OMAP: Fix clockevent support for hrtimers
|
|
The original justification for cap_task_kill() was as follows:
check_kill_permission() does appropriate uid equivalence checks.
However with file capabilities it becomes possible for an
unprivileged user to execute a file with file capabilities
resulting in a more privileged task with the same uid.
However now that cap_task_kill() always returns 0 (permission
granted) when p->uid==current->uid, the whole hook is worthless,
and only likely to create more subtle problems in the corner cases
where it might still be called but return -EPERM. Those cases
are basically when uids are different but euid/suid is equivalent
as per the check in check_kill_permission().
One example of a still-broken application is 'at' for non-root users.
This patch removes cap_task_kill().
Signed-off-by: Serge Hallyn <serge@hallyn.com>
Acked-by: Andrew G. Morgan <morgan@kernel.org>
Earlier-version-tested-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is a bug correction for a macro that generated wrong results.
Nobody used it in official kernel tree, my driver did.
Signed-off-by: Davide Rizzo <davide@elpa.it>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Until DSP MMU code is merged, dsp_request_mem() does not exist.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Define AT91_USART0, 1, 2 so the selection of the UART for early kernel
messages works.
(See commit fa3218d8594869b38b1a170ea36d176ac455b897).
Replace AT91_SHDC with AT91_SHDWC to be consistent with other AT91 platforms.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
MemoryStick storage cards, when in parallel mode, send several meaningful bits
of their "INT" register as part of command response. This data is stored by
host and can be used to spare invocation of "GET_INT" TPC on each data page
transferred between host and card.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix kernel-doc notation warnings in fs/.
Warning(mmotm-2008-0314-1449//fs/super.c:560): missing initial short description on line:
* mark_files_ro
Warning(mmotm-2008-0314-1449//fs/locks.c:1277): missing initial short description on line:
* lease_get_mtime
Warning(mmotm-2008-0314-1449//fs/locks.c:1277): missing initial short description on line:
* lease_get_mtime
Warning(mmotm-2008-0314-1449//fs/namei.c:1368): missing initial short description on line:
* lookup_one_len: filesystem helper to lookup single pathname component
Warning(mmotm-2008-0314-1449//fs/buffer.c:3221): missing initial short description on line:
* bh_uptodate_or_lock: Test whether the buffer is uptodate
Warning(mmotm-2008-0314-1449//fs/buffer.c:3240): missing initial short description on line:
* bh_submit_read: Submit a locked buffer for reading
Warning(mmotm-2008-0314-1449//fs/fs-writeback.c:30): missing initial short description on line:
* writeback_acquire: attempt to get exclusive writeback access to a device
Warning(mmotm-2008-0314-1449//fs/fs-writeback.c:47): missing initial short description on line:
* writeback_in_progress: determine whether there is writeback in progress
Warning(mmotm-2008-0314-1449//fs/fs-writeback.c:58): missing initial short description on line:
* writeback_release: relinquish exclusive writeback access against a device.
Warning(mmotm-2008-0314-1449//include/linux/jbd.h:351): contents before sections
Warning(mmotm-2008-0314-1449//include/linux/jbd.h:561): contents before sections
Warning(mmotm-2008-0314-1449//fs/jbd/transaction.c:1935): missing initial short description on line:
* void journal_invalidatepage()
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In the process of writing up the mechanical proof of correctness for the
dynticks/preemptable-RCU interface, I noticed misplaced memory barriers in
rcu_enter_nohz() and rcu_exit_nohz().
This patch puts them in the right place and adds a comment. The key thing to
keep in mind is that rcu_enter_nohz() is -exiting- the mode that can legally
execute RCU read-side critical sections.
The memory barrier must be between any potential RCU read-side critical
sections and the increment of the per-CPU dynticks_progress_counter, and thus
must come -before- this increment. And vice versa for rcu_exit_nohz().
The locking in the scheduler is probably saving us for the moment.
Also, switch to smp_mb() - we don't need a barrier for uniprocessor kernels.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <srostedt@redhat.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
4096 will not fit into the immediate field of a compare instruction,
in fact it will end up being -4096 causing the check to fail every
time and thus disabling backoff.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WAKE_IDLE is too agressive on multi-core CPUs with the new
wake-affine code, keep it on for SMT/HT balancing alone
(where there's no cache affinity at all between logical CPUs).
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
improve affine wakeups. Maintain the 'overlap' metric based on CFS's
sum_exec_runtime - which means the amount of time a task executes
after it wakes up some other task.
Use the 'overlap' for the wakeup decisions: if the 'overlap' is short,
it means there's strong workload coupling between this task and the
woken up task. If the 'overlap' is large then the workload is decoupled
and the scheduler will move them to separate CPUs more easily.
( Also slightly move the preempt_check within try_to_wake_up() - this has
no effect on functionality but allows 'early wakeups' (for still-on-rq
tasks) to be correctly accounted as well.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
Revert "unexport bio_{,un}map_user"
relay: fix subbuf_splice_actor() adding too many pages
The ps2esdi driver was marked as BROKEN more than two years ago due to being
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: Add Marvell 6121 SATA support
pata_ali: use atapi_cmd_type() to determine cmd type instead of transfer size
ahci: implement skip_host_reset parameter
ahci: request all PCI BARs
devres: implement pcim_iomap_regions_request_all()
libata-acpi: improve dock event handling
|
|
Some drivers need to reserve all PCI BARs to prevent other drivers
misusing unoccupied BARs. pcim_iomap_regions_request_all() requests
all BARs and iomap specified BARs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
