| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Clean up for omap DSS board init in preparation for adding DT support.
By Tomi Valkeinen
via Tomi Valkeinen (1) and Tony Lindgren (1)
* tag 'omap-cleanup-dss-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
OMAPDSS: DSI: implement generic DSI pin config
OMAPDSS: Taal: move reset gpio handling to taal driver
OMAPDSS: TFP410: rename dvi files to tfp410
OMAPDSS: TFP410: rename dvi -> tfp410
OMAP: board-files: remove custom PD GPIO handling for DVI output
OMAPDSS: panel-dvi: add PD gpio handling
Resolved context conflicts in arch/arm/mach-omap2/board-omap4panda.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards
Board specific changes for omap.
Note that these are based on omap-pm-regulator-for-v3.5 as
both branches are adding twl regulators.
By Paul Gortmaker (8) and others
via Linus Torvalds (38) and others
* tag 'omap-board-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
OMAP: omap4panda: Use common configuration for V1V8, V2V1 supplies
OMAP: 4430SDP: Use common configuration for V1V8, V2V1 supplies
OMAP4: twl-common: Add twl6030 V1V8, V2V1 SMPS common configuration
ARM: OMAP: Mark Beagleboard-xM MMC bus as 4-bit
Add MSUB support for the LogicPD OMAP3530 DevKits
ARM: OMAP: rx51: Platform support for lis3lv02d accelerometer
ARM: OMAP2+: craneboard: register emac device
ARM: OMAP4: board-omap4panda: Register platform device for HDMI audio codec
ARM: OMAP4: board-4430sdp: Register platform device for HDMI audio codec
ARM: OMAP: devices: Register platform devices for HDMI audio
ARM: OMAP3: igep0020: Add support for Micron NAND Flash storage memory
ARM: OMAP2+: nand: Make board_onenand_init() visible to board code
ARM: OMAP3: cm-t35: add support for power off
ARM: OMAP: WiLink platform data for the PandaBoard
ARM: OMAP2PLUS: Enable HIGHMEM
ARM: OMAP: omap2plus_defconfig: Enable ehci-omap and sms95xx support
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
dmaengine_prep_slave_single() is a helper function which is supposed to be used
to prepare a transfer of a single contingous buffer. Currently the function
takes a pointer to such a buffer from which it builds a scatterlist and passes
it on to device_prep_slave_sg. The dmaengine framework requires that any
scatterlist that is passed to device_prep_slave_sg is mapped and it may not be
unmapped until the DMA operation has completed. This is not the here and any use
of dmaengine_prep_slave_single() will lead to undefined behaviour (Most likely a
system crash).
This patch changes dmaengine_prep_slave_single() to take a dma_addr_t instead of
a pointer to a buffer and moves the responsibility of mapping and unmapping the
buffer up to the caller.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
When platform keymap is not supplied to matrix_keypad_build_keymap()
and device tree support is enabled, try locating specified property
and load keymap from it. If property name is not defined, try using
"linux,keymap".
Based on earlier patch by Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Change matrix-keymap helper to be out-of-line, like sparse keymap,
allow the helper perform basic keymap validation and return errors,
and prepare for device tree support.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Signed-off-by: Jean-François Dagenais <jeff.dagenais@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
This driver adds support for the Synaptics NavPoint touchpad connected
to a PXA27x SSP port in SPI slave mode. The device emulates a mouse;
a tap or tap-and-a-half drag gesture emulates the left mouse button.
For example, use the xf86-input-evdev driver for an X pointing device.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
An implementation of CoDel AQM, from Kathleen Nichols and Van Jacobson.
http://queue.acm.org/detail.cfm?id=2209336
This AQM main input is no longer queue size in bytes or packets, but the
delay packets stay in (FIFO) queue.
As we don't have infinite memory, we still can drop packets in enqueue()
in case of massive load, but mean of CoDel is to drop packets in
dequeue(), using a control law based on two simple parameters :
target : target sojourn time (default 5ms)
interval : width of moving time window (default 100ms)
Based on initial work from Dave Taht.
Refactored to help future codel inclusion as a plugin for other linux
qdisc (FQ_CODEL, ...), like RED.
include/net/codel.h contains codel algorithm as close as possible than
Kathleen reference.
net/sched/sch_codel.c contains the linux qdisc specific glue.
Separate structures permit a memory efficient implementation of fq_codel
(to be sent as a separate work) : Each flow has its own struct
codel_vars.
timestamps are taken at enqueue() time with 1024 ns precision, allowing
a range of 2199 seconds in queue, and 100Gb links support. iproute2 uses
usec as base unit.
Selected packets are dropped, unless ECN is enabled and packets can get
ECN mark instead.
Tested from 2Mb to 10Gb speeds with no particular problems, on ixgbe and
tg3 drivers (BQL enabled).
Usage: tc qdisc ... codel [ limit PACKETS ] [ target TIME ]
[ interval TIME ] [ ecn ]
qdisc codel 10: parent 1:1 limit 2000p target 3.0ms interval 60.0ms ecn
Sent 13347099587 bytes 8815805 pkt (dropped 0, overlimits 0 requeues 0)
rate 202365Kbit 16708pps backlog 113550b 75p requeues 0
count 116 lastcount 98 ldelay 4.3ms dropping drop_next 816us
maxpacket 1514 ecn_mark 84399 drop_overlimit 0
CoDel must be seen as a base module, and should be used keeping in mind
there is still a FIFO queue. So a typical setup will probably need a
hierarchy of several qdiscs and packet classifiers to be able to meet
whatever constraints a user might have.
One possible example would be to use fq_codel, which combines Fair
Queueing and CoDel, in replacement of sfq / sfq_red.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>
Cc: Kathleen Nichols <nichols@pollere.com>
Cc: Van Jacobson <van@pollere.net>
Cc: Tom Herbert <therbert@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an optimized boolean function to check if
2 ethernet addresses are the same.
This is to avoid any confusion about compare_ether_addr_64bits
returning an unsigned, and not being able to use the
compare_ether_addr_64bits function for sorting ala memcmp.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It actually works on the input queue and will use its read mem
routines, thus it's better to have in in the tcp_input.c file.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dst_check() will take care of SA (and obsolete field), hence
IPsec rekeying scenario is taken into account.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Vlad Yaseivch <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 8a83a00b0735190384a348156837918271034144.
It causes regressions for S390 devices, because it does an
unconditional DST drop on SKBs for vlans and the QETH device
needs the neighbour entry hung off the DST for certain things
on transmit.
Arnd can't remember exactly why he even needed this change.
Conflicts:
drivers/net/macvlan.c
net/8021q/vlan_dev.c
net/core/dev.c
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows comparing hash and len in one operation on 64-bit
architectures. Right now only __d_lookup_rcu() takes advantage of this,
since that is the case we care most about.
The use of anonymous struct/unions hides the alternate 64-bit approach
from most users, the exception being a few cases where we initialize a
'struct qstr' with a static initializer. This makes the problematic
cases use a new QSTR_INIT() helper function for that (but initializing
just the name pointer with a "{ .name = xyzzy }" initializer remains
valid, as does just copying another qstr structure).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With the adding of function tracing event to perf, it caused a
side effect that produces the following warning when enabling all
events in ftrace:
# echo 1 > /sys/kernel/debug/tracing/events/enable
[console]
event trace: Could not enable event function
This is because when enabling all events via the debugfs system
it ignores events that do not have a ->reg() function assigned.
This was to skip over the ftrace internal events (as they are
not TRACE_EVENTs). But as the ftrace function event now has
a ->reg() function attached to it for use with perf, it is no
longer ignored.
Worse yet, this ->reg() function is being called when it should
not be. It returns an error and causes the above warning to
be printed.
By adding a new event_call flag (TRACE_EVENT_FL_IGNORE_ENABLE)
and have all ftrace internel event structures have it set,
setting the events/enable will no longe try to incorrectly enable
the function event and does not warn.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Add iSerialNumber to usb_composite_driver to allow setting a default value.
This is useful when the module is compiled-in. Then the composite_bind
is executed at kernel boot and string id for iSerialNumber can be overridden
even if there is no iSerialNumber kernel commandline parameter.
If the string id is not overridden, then get_string will never attempt to
look for the alternative string contents using cdev->serial_override.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add usb_remove_config to unbind a configuration and remove it from
the configs list. This allows implementing composite gadget drivers that
can disconnect themself from the bus and that will later be re-enumerated
with a different configuration.
Gadget drivers must call usb_gadget_disconnect before calling this
function to disable the pullup, disconnect the device from the host,
and prevent the host from enumerating the device while we are changing
the gadget configuration.
Signed-off-by: Benoit Goby <benoit@android.com>
[change return type of [usb_]remove_config]
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The global wait_queue that is used for line discipline idle handling is
moved to a separate wait_queue for each line instance. This prevents
unnecessary blocking on one line, because of idle handling on another
line.
Signed-off-by: Ivo Sieben <meltedpianoman@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Conflicts:
drivers/video/omap2/displays/panel-taal.c
Merge OMAP DSS related board file changes. The branch will also be
merged through linux-omap tree to solve conflicts.
|
|
This removes a repeated word and a repeated and incomplete line from two
pinctrl headers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt2
By Stephen Warren (29) and others
via Stephen Warren
* 'for-3.5/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (43 commits)
ARM: dt: tegra trimslice: add support for audio
ARM: dt: tegra trimslice: enable SDHCI1 controller
ARM: dt: tegra trimslice: add RTC I2C device
ARM: dt: tegra seaboard: add i2c devices
ARM: dt: tegra seaboard: configure I2C2 pinmux
ARM: dt: tegra seaboard: fix I2C2 SCL rate
ARM: dt: tegra: enable als and proximity sensor
+ pinctrl mergebase branch
The pinctrl mergebase branch merge conflicts in drivers/pinctrl/core.c
that were resolved.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/pinctrl
By Stephen Warren
via Stephen Warren
* 'for-3.5/gpio-pinmux' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
pinctrl: tegra: error reporting cleanup
pinctrl: tegra: debugfs enhancements
pinctrl: tegra: refactor probe handling
ARM: dt: tegra20: add pinmux to device tree
ARM: dt: tegra cardhu: add pinmux to device tree
ARM: tegra: Remove pre-pinctrl pinmux driver
ARM: tegra: Switch to new pinctrl driver
gpio: tegra: Hide tegra_gpio_enable/disable()
ARM: tegra: seaboard: Don't gpio_request() ISL29018_IRQ
gpio: tegra: configure pins during irq_set_type
ARM: tegra: Remove VBUS_GPIO handling from board files
usb: ehci-tegra: Add vbus_gpio to platform data
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl into next/pinctrl
By Stephen Warren (12) and others
via Linus Walleij
* tag 'pinctrl-mergebase-20120418' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (24 commits)
pinctrl: show pin name for pingroups in sysfs
pinctrl: show pin name when request pins
pinctrl: implement devm_pinctrl_get()/put()
pinctrl: a minor fix of pin config debug information
pinctrl: pinconf: fix compilation error if PINCONF is not selected
pinctrl: allow pctldevs to decode pin config in debugfs
pinctrl: ifdef CONFIG_DEBUG_FS cleanup
pinctrl: mark non-EXPERIMENTAL
pinctrl: tegra: Add complete device tree support
dt: Document Tegra20/30 pinctrl binding
dt: Move Tegra20 pin mux binding into new pinctrl directory
dt: pinctrl: Document device tree binding
dt: add property iteration helpers
pinctrl: implement pinctrl deferred probing
pinctrl: add some error checking for user interfaces
pinctrl: fix pinmux_check_ops error checking
pinctrl: replace list_*() with get_*_count()
pinctrl: mark const init data with __initconst instead of __initdata
Documentation: pinctrl: add missing spi0_0 grp in example
pinctrl: fix build when CONFIG_OF && !CONFIG_PINCTRL
...
Resolved conflicts in drivers/pinctrl/core.c due to same patch being
applied in two branches.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc-next
|
|
Conflicts:
arch/sh/Kconfig
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
ETHTOOL_GMODULEINFO returns a new struct ethtool_modinfo that will return the
type and size of plug-in module eeprom (such as SFP+) for parsing
by userland program.
ETHTOOL_GMODULEEEPROM returns the raw eeprom information
using the existing ethtool_eeprom structture to return the data
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Add a boolean function to check if 2 ethernet addresses
are the same.
This is to avoid any confusion about compare_ether_addr
returning an unsigned, and not being able to use the
compare_ether_addr function for sorting ala memcmp.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Linux 3.4-rc6
|
|
When writing a firewire driver that doesn't deal with struct fw_device
objects (e.g. it only publishes FireWire units and doesn't subscribe to
them), you likely need to keep referenced to struct fw_card objects so
that you can send messages to other nodes. This patch moves
fw_card_put(), fw_card_get() and fw_card_release() into the public
include/linux/firewire.h header instead of drivers/firewire/core.h, and
adds EXPORT_SYMBOL_GPL(fw_card_release).
The firewire-sbp-target module requires these so it can keep a reference
to the fw_card object in order that it can fetch ORBs to execute and
read/write related data and status information.
Signed-off-by: Chris Boot <bootc@bootc.net>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Sometimes it's useful to know the FireWire speed of the request that has
just come in to a fw_address_handler callback. As struct fw_request is
opaque we can't peek inside to get the speed out of the struct fw_packet
that's just inside. For example, the SBP-2 spec says:
"The speed at which the block write request to the MANAGEMENT_AGENT
register is received shall determine the speed used by the target for
all subsequent requests to read the initiator’s configuration ROM, fetch
ORB’s from initiator memory or store status at the initiator’s
status_FIFO. Command block ORB’s separately specify the speed for
requests addressed to the data buffer or page table."
[ ANSI T10/1155D Revision 4 page 53/54 ]
Signed-off-by: Chris Boot <bootc@bootc.net>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch remove old max8997-muic drvier because of newly Extcon framework.
Extcon framework manages the external connector, so add extcon-max8997 driver
by using Extcon interface to support MUIC feature of Maxim 8997 PMIC instead
of max8997-muic driver(drivers/misc/max8997-muic.c).
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch removes the original usage of dev_attr->max_sectors in favor of
dev_attr->hw_max_sectors that is now being enforced by target core from
within transport_generic_cmd_sequencer() for SCF_SCSI_DATA_SG_IO_CDB ops.
After the recent se_task removal patches from hch, this value for IBLOCK
backends being set via configfs by userspace from an saved max_sectors
value that is turning out to be problematic, so it makes sense to go ahead
and remove this now legacy attribute all-together.
This patch also continues to make se_dev_set_default_attribs() do
(sectors / block_size) alignment for what actually get used by
target_core_mod to be safe here, following the same alignment currently
used by fabric_max_sectors.
Reported-by: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The current RCU_FAST_NO_HZ assumes that timers do not migrate unless a
CPU goes offline, in which case it assumes that the CPU will have to come
out of dyntick-idle mode (cancelling the timer) in order to go offline.
This is important because when RCU_FAST_NO_HZ permits a CPU to enter
dyntick-idle mode despite having RCU callbacks pending, it posts a timer
on that CPU to force a wakeup on that CPU. This wakeup ensures that the
CPU will eventually handle the end of the grace period, including invoking
its RCU callbacks.
However, Pascal Chapperon's test setup shows that the timer handler
rcu_idle_gp_timer_func() really does get invoked in some cases. This is
problematic because this can cause the CPU that entered dyntick-idle
mode despite still having RCU callbacks pending to remain in
dyntick-idle mode indefinitely, which means that its RCU callbacks might
never be invoked. This situation can result in grace-period delays or
even system hangs, which matches Pascal's observations of slow boot-up
and shutdown (https://lkml.org/lkml/2012/4/5/142). See also the bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=806548
This commit therefore causes the "should never be invoked" timer handler
rcu_idle_gp_timer_func() to use smp_call_function_single() to wake up
the CPU for which the timer was intended, allowing that CPU to invoke
its RCU callbacks in a timely manner.
Reported-by: Pascal Chapperon <pascal.chapperon@wanadoo.fr>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
The "uim" deamon requires sysfs entries that are filled in using
this platform data.
Signed-off-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The header exports API for application layer
1. move under include/linux and add to the export list
2. update include path n the sources
3. update TODO
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
uuid is used in mei.h interface
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
twl6040 has three power supply source:
VBAT needs to be connected to VBAT, VIO, and V2V1.
Add regulator support for the VIO, V2V1 supplies.
Initially handle the two supply together with bulk commands.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Function rename to ensure that the functionality of nfs_unlock_request()
mirrors that of nfs_lock_request(). Then let nfs_unlock_and_release_request()
do the work of what used to be called nfs_unlock_request()...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Fred Isaman <iisaman@netapp.com>
|
|
We only have two places where we need to grab a reference when trying
to lock the nfs_page. We're better off making that explicit.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Fred Isaman <iisaman@netapp.com>
|
|
We have to unlock the nfs_page before we call nfs_end_page_writeback
to avoid races with functions that expect the page to be unlocked
when PG_locked and PG_writeback are not set.
The problem is that nfs_unlock_request also releases the nfs_page,
causing a deadlock if the release of the nfs_open_context
triggers an iput() while the PG_writeback flag is still set...
The solution is to separate the unlocking and release of the nfs_page,
so that we can do the former before nfs_end_page_writeback and the
latter after.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Fred Isaman <iisaman@netapp.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace into perf/core
|
|
We need to sync with the GFX ring as ttm might have schedule bo move
on it and new command scheduled for other ring need to wait for bo
data to be in place.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
cleanup-dss
|
|
Since it's not like we will re-arrange the keys at run-time, it
seems proper to allow the keymap data to be const. This solves
a compilation warning in ux500.
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch converts the iTCO_wdt driver to use the multi-function device
driver model. It uses resources discovered by the lpc_ich driver, so that
it no longer does its own PCI scanning.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add support for National Semiconductor / TI LM3533 lighting power chips.
This is the core driver which provides register access over I2C and
registers the ambient-light-sensor, LED and backlight sub-drivers.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Noticed this comment didn't get updated when
tcp_build_and_update_options was refactored.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The variable 'dw_mci_card_workqueue' is a global variable shared between
multiple instances of the dw_mmc host controller. Due to this, data
corruption has been noticed when multiple instances of dw_mmc controllers
are actively reading/writing the media. Fix this by adding a instance
of 'struct workqueue_struct' for each host instance and removing the
global 'dw_mci_card_workqueue' instance.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Current implementation decides the card type exclusively. Even though
eMMC device can support both HS200 and DDR mode, card type will be
set only for HS200. If the host doesn't support HS200 but has DDR
capability, then DDR mode can't be selected.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This patch adds the Integrated Legacy Block DeviceID for the Centerton CPU. It will be used in the GPIO and Multifunction Devices driver.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
