| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The specific destination is the host we direct unicast replies to.
Usually this is the original packet source address, but if we are
responding to a multicast or broadcast packet we have to use something
different.
Specifically we must use the source address we would use if we were to
send a packet to the unicast source of the original packet.
The routing cache precomputes this value, but we want to remove that
precomputation because it creates a hard dependency on the expensive
rpfilter source address validation which we'd like to make cheaper.
There are only three places where this matters:
1) ICMP replies.
2) pktinfo CMSG
3) IP options
Now there will be no real users of rt->rt_spec_dst and we can simply
remove it altogether.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename it to ip_send_unicast_reply() and add explicit 'saddr'
argument.
This removed one of the few users of rt->rt_spec_dst.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's completely unnecessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of using a fixed value of "-1" or "-EMSGSIZE", propagate what
the nla_*() interfaces actually return.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow PHY drivers to supply their own device matching function
(match_phy_device()), or to be matched OF compatible properties.
PHYs following IEEE802.3 clause 45 have more than one device
identifier constants, which breaks the default device matching code.
Other 10G PHYs don't follow the standard manufacturer/device
identifier register layout standards, but they do use the standard
MDIO bus protocols for register access. Both of these require
adjustments to the PHY driver to device matching code.
If the there is an of_node associated with such a PHY, we can match it
to its driver using the "compatible" properties, just as we do with
certain platform devices. If the "compatible" property match fails,
first check if there is a driver supplied matching function, and if
not fall back to the existing identifier matching rules.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IEEE802.3 clause 45 MDIO bus protocol allows for directly
addressing PHY registers using a 21 bit address, and is used by many
10G Ethernet PHYS. Already existing is the ability of MDIO bus
drivers to use clause 45, with the MII_ADDR_C45 flag. Here we add
struct phy_c45_device_ids to hold the device identifier registers
present in clause 45. struct phy_device gets a couple of new fields:
c45_ids to hold the identifiers and is_c45 to signal that it is clause
45.
get_phy_device() gets a new parameter is_c45 to indicate that the PHY
device should use the clause 45 protocol, and its callers are adjusted
to pass false. The follow-on patch to of_mdio.c will pass true where
appropriate.
EXPORT phy_device_create() so that the follow-on patch to of_mdio.c
can use it to create phy devices for PHYs, that have non-standard
device identifier registers, based on the device tree bindings.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit c074da2810c118b3812f32d6754bd9ead2f169e7.
This change has several unwanted side effects:
1) Sockets will cache the DST_NOCACHE route in sk->sk_rx_dst and we'll
thus never create a real cached route.
2) All TCP traffic will use DST_NOCACHE and never use the routing
cache at all.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. removed code replication for tov calculation for 1G, 10G and
made is common for speed > 1G (1G, 10G, 40G, 100G).
2. defines values for #4 different 40G Phys (KR4, LF4, SR4, CR4)
Signed-off-by: Parav Pandit <parav.pandit@emulex.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removes all RTA_GET*() and RTA_PUT*() variations, as well as the
the unused rtattr_strcmp(). Get rid of rtm_get_table() by moving
it to its only user decnet.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DDOS synflood attacks hit badly IP route cache.
On typical machines, this cache is allowed to hold up to 8 Millions dst
entries, 256 bytes for each, for a total of 2GB of memory.
rt_garbage_collect() triggers and tries to cleanup things.
Eventually route cache is disabled but machine is under fire and might
OOM and crash.
This patch exploits the new TCP early demux, to set a nocache
boolean in case incoming TCP frame is for a not yet ESTABLISHED or
TIMEWAIT socket.
This 'nocache' boolean is then used in case dst entry is not found in
route cache, to create an unhashed dst entry (DST_NOCACHE)
SYN-cookie-ACK sent use a similar mechanism (ipv4: tcp: dont cache
output dst for syncookies), so after this patch, a machine is able to
absorb a DDOS synflood attack without polluting its IP route cache.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No longer used and a poor interface as they were macros
with embedded gotos.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The AT86RF231 is a feature rich, low-power 2.4 GHz radio transceiver
designed for industrial and consumer ZigBee/IEEE 802.15.4, 6LoWPAN,
RF4CE and high data rate 2.4 GHz ISM band applications.
This patch adds support for the Atmel RF230/231 radio transceivers.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every real 802.15.4 transceiver, which works with software MAC layer,
can be classified as a wpan device in this stack. So the wpan device
implementation provides missing link in datapath between the device
drivers and the Linux network queue.
According to the IEEE 802.15.4 standard each packet can be one of the
following types:
- beacon
- MAC layer command
- ACK
- data
This patch adds support for the data packet-type only, but this is
enough to perform data transmission and receiving over radio.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove use of module parameters on caif hsi device, as
rtnl configuration parameters are already supported.
All caif hsi configuration data is put in cfhsi_config,
and default values in hsi_default_config.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove use of struct platform_device, and replace it with
struct cfhsi_ops. Updated variable names in the same
spirit:
cfhsi_get_dev to cfhsi_get_ops,
cfhsi->dev to cfhsi->ops and,
cfhsi->dev.drv to cfhsi->ops->cb_ops.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add RTNL support for managing the caif hsi interface.
The HSI HW interface is no longer registering as a device,
instead we use symbol_get to get hold of the HSI API.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing kernel doc for sk_rx_dst
Move sk_rx_dst to avoid two 32bit holes on 64bit arches
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With early demux enabled by default for TCP flows, there is high chance that
skb->sk will be non-null. 'unlikely()' was removed from __inet_lookup_skb() but
maybe it can be removed from skb_steal_sock() as well.
Note: skb_steal_sock() is also called by __inet6_lookup_skb() and
__udp4_lib_lookup_skb() but they are protected by their own 'unlikely' calls.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo says:
====================
The following four patches provide Netfilter fixes for the cthelper
infrastructure that was recently merged mainstream, they are:
* two fixes for compilation breakage with two different configurations:
- CONFIG_NF_NAT=m and CONFIG_NF_CT_NETLINK=y
- NF_CONNTRACK_EVENTS=n and CONFIG_NETFILTER_NETLINK_QUEUE_CT=y
* two fixes for sparse warnings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't cache output dst for syncookies, as this adds pressure on IP route
cache and rcu subsystem for no gain.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change is meant to add a control for disabling early socket demux.
The main motivation behind this patch is to provide an option to disable
the feature as it adds an additional cost to routing that reduces overall
throughput by up to 5%. For example one of my systems went from 12.1Mpps
to 11.6 after the early socket demux was added. It looks like the reason
for the regression is that we are now having to perform two lookups, first
the one for an established socket, and then the one for the routing table.
By adding this patch and toggling the value for ip_early_demux to 0 I am
able to get back to the 12.1Mpps I was previously seeing.
[ Move local variables in ip_rcv_finish() down into the basic
block in which they are actually used. -DaveM ]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CONFIG_NF_CT_NETLINK=y
LD init/built-in.o
net/built-in.o:(.data+0x4408): undefined reference to `nf_nat_tcp_seq_adjust'
make: *** [vmlinux] Error 1
This patch adds a new pointer hook (nfq_ct_nat_hook) similar to other existing
in Netfilter to solve our complicated configuration dependencies.
Reported-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This removes some sparse warnings.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Input packet processing for local sockets involves two major demuxes.
One for the route and one for the socket.
But we can optimize this down to one demux for certain kinds of local
sockets.
Currently we only do this for established TCP sockets, but it could
at least in theory be expanded to other kinds of connections.
If a TCP socket is established then it's identity is fully specified.
This means that whatever input route was used during the three-way
handshake must work equally well for the rest of the connection since
the keys will not change.
Once we move to established state, we cache the receive packet's input
route to use later.
Like the existing cached route in sk->sk_dst_cache used for output
packets, we have to check for route invalidations using dst->obsolete
and dst->ops->check().
Early demux occurs outside of a socket locked section, so when a route
invalidation occurs we defer the fixup of sk->sk_rx_dst until we are
actually inside of established state packet processing and thus have
the socket locked.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't pretend that inet_protos[] and inet6_protos[] are hashes, thay
are just a straight arrays. Remove all unnecessary hash masking.
Document MAX_INET_PROTOS.
Use RAW_HTABLE_SIZE when appropriate.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds two exported functions. One allows to mark option
instance as changed and the second processes change check and does
transfer of changed options to userspace.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce struct team_option_inst_info and push option instance info
there. It can be then easily passed to gsetter context and used for
feature async option changes.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc Kleine-Budde says:
====================
here is our second pull request for net-next. In this series Federico
Vaga adds a pci driver for c_can/d_can hardware using the existing
generic c_can driver. The remaining 6 patches are by Oliver Hartkopp.
He adds CANFD support to the CAN stack while keeping binary
compatibility for existing applications. CANFD is an extension to the
existing CAN standard, it allows longer CAN frames and/or higher data
rates. There's no real hardware available yet, but this series adds
CANFD support to the vcan driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John Linville says:
====================
This is a sizeable batch of updates intended for 3.6...
The bulk of the changes here are Bluetooth. Gustavo says:
Here goes the first Bluetooth pull request for 3.6, we have
queued quite a lot of work. Andrei Emeltchenko added the AMP
Manager code, a lot of work is needed, but the first bit are
already there. This code is disabled by default. Mat Martineau
changed the whole L2CAP ERTM state machine code, replacing
the old one with a new implementation. Besides that we had
lot of coding style fixes (to follow net rules), more l2cap
core separation from socket and many clean ups and fixed all
over the tree.
Along with the above, there is a healthy dose of ath9k, iwlwifi,
and other driver updates. There is also another pull from the
wireless tree to resolve some merge issues. I also fixed-up some
merge discrepencies between net-next and wireless-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- update sanity checks
- add DLC to length conversion helpers
- can_dlc2len() - get data length from can_dlc with sanitized can_dlc
- can_len2dlc() - map the sanitized data length to an appropriate DLC
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
- introduce a new sockopt CAN_RAW_FD_FRAMES to allow CAN FD frames
- handle CAN frames and CAN FD frames simultaneously when enabled
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
- handle ETH_P_CAN and ETH_P_CANFD skbuffs
- update sanity checks for CAN and CAN FD
- make sure the CAN frame can pass the selected CAN netdevice on send
- bump core version and abi version to indicate the new CAN FD support
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
- add new struct canfd_frame
- check identical element offsets in struct can_frame and struct canfd_frame
- new ETH_P_CANFD definition to tag CAN FD skbs correctly
- add CAN_MTU and CANFD_MTU definitions for easy frame and mode detection
- add CAN[FD]_MAX_[DLC|DLEN] helper constants to remove hard coded values
- update existing struct can_frame with helper constants and comments
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
Conflicts:
drivers/net/wireless/iwlwifi/dvm/testmode.c
drivers/net/wireless/iwlwifi/pcie/trans.c
|
|
ERROR: "nfqnl_ct_parse" [net/netfilter/nfnetlink_queue.ko] undefined!
ERROR: "nfqnl_ct_seq_adjust" [net/netfilter/nfnetlink_queue.ko] undefined!
ERROR: "nfqnl_ct_put" [net/netfilter/nfnetlink_queue.ko] undefined!
ERROR: "nfqnl_ct_get" [net/netfilter/nfnetlink_queue.ko] undefined!
We have to use CONFIG_NETFILTER_NETLINK_QUEUE_CT in
include/net/netfilter/nfnetlink_queue.h, not CONFIG_NF_CONNTRACK.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In "9cb0176 netfilter: add glue code to integrate nfnetlink_queue and ctnetlink"
the compilation with NF_CONNTRACK disabled is broken. This patch fixes this
issue.
I have moved the conntrack part into nfnetlink_queue_ct.c to avoid
peppering the entire nfnetlink_queue.c code with ifdefs.
I also needed to rename nfnetlink_queue.c to nfnetlink_queue_pkt.c
to update the net/netfilter/Makefile to support conditional compilation
of the conntrack integration.
This patch also adds CONFIG_NETFILTER_QUEUE_CT in case you want to explicitly
disable the integration between nf_conntrack and nfnetlink_queue.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Signed-off-by: Rémi Denis-Courmont <remi@remlab.net>
Cc: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo says:
====================
This is the second batch of Netfilter updates for net-next. It contains the
kernel changes for the new user-space connection tracking helper
infrastructure.
More details on this infrastructure are provides here:
http://lwn.net/Articles/500196/
Still, I plan to provide some official documentation through the
conntrack-tools user manual on how to setup user-space utilities for this.
So far, it provides two helper in user-space, one for NFSv3 and another for
Oracle/SQLnet/TNS. Yet in my TODO list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix code style - place the asterisk where it belongs.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are good reasons to supports helpers in user-space instead:
* Rapid connection tracking helper development, as developing code
in user-space is usually faster.
* Reliability: A buggy helper does not crash the kernel. Moreover,
we can monitor the helper process and restart it in case of problems.
* Security: Avoid complex string matching and mangling in kernel-space
running in privileged mode. Going further, we can even think about
running user-space helpers as a non-root process.
* Extensibility: It allows the development of very specific helpers (most
likely non-standard proprietary protocols) that are very likely not to be
accepted for mainline inclusion in the form of kernel-space connection
tracking helpers.
This patch adds the infrastructure to allow the implementation of
user-space conntrack helpers by means of the new nfnetlink subsystem
`nfnetlink_cthelper' and the existing queueing infrastructure
(nfnetlink_queue).
I had to add the new hook NF_IP6_PRI_CONNTRACK_HELPER to register
ipv[4|6]_helper which results from splitting ipv[4|6]_confirm into
two pieces. This change is required not to break NAT sequence
adjustment and conntrack confirmation for traffic that is enqueued
to our user-space conntrack helpers.
Basic operation, in a few steps:
1) Register user-space helper by means of `nfct':
nfct helper add ftp inet tcp
[ It must be a valid existing helper supported by conntrack-tools ]
2) Add rules to enable the FTP user-space helper which is
used to track traffic going to TCP port 21.
For locally generated packets:
iptables -I OUTPUT -t raw -p tcp --dport 21 -j CT --helper ftp
For non-locally generated packets:
iptables -I PREROUTING -t raw -p tcp --dport 21 -j CT --helper ftp
3) Run the test conntrackd in helper mode (see example files under
doc/helper/conntrackd.conf
conntrackd
4) Generate FTP traffic going, if everything is OK, then conntrackd
should create expectations (you can check that with `conntrack':
conntrack -E expect
[NEW] 301 proto=6 src=192.168.1.136 dst=130.89.148.12 sport=0 dport=54037 mask-src=255.255.255.255 mask-dst=255.255.255.255 sport=0 dport=65535 master-src=192.168.1.136 master-dst=130.89.148.12 sport=57127 dport=21 class=0 helper=ftp
[DESTROY] 301 proto=6 src=192.168.1.136 dst=130.89.148.12 sport=0 dport=54037 mask-src=255.255.255.255 mask-dst=255.255.255.255 sport=0 dport=65535 master-src=192.168.1.136 master-dst=130.89.148.12 sport=57127 dport=21 class=0 helper=ftp
This confirms that our test helper is receiving packets including the
conntrack information, and adding expectations in kernel-space.
The user-space helper can also store its private tracking information
in the conntrack structure in the kernel via the CTA_HELP_INFO. The
kernel will consider this a binary blob whose layout is unknown. This
information will be included in the information that is transfered
to user-space via glue code that integrates nfnetlink_queue and
ctnetlink.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
