| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds proper handling of the vNIC hot removal event, which includes
a rescind-channel-offer message from the host side that triggers vNIC close and
removal. In this case, the notices to the host during close and removal is not
necessary because the channel is rescinded. This patch blocks these unnecessary
messages, and lets vNIC removal process complete normally.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow reading of timestamps and cmsg at the same time on all relevant
socket families. One use is to correlate timestamps with egress
device, by asking for cmsg IP_PKTINFO.
on AF_INET sockets, call the relevant function (ip_cmsg_recv). To
avoid changing legacy expectations, only do so if the caller sets a
new timestamping flag SOF_TIMESTAMPING_OPT_CMSG.
on AF_INET6 sockets, IPV6_PKTINFO and all other recv cmsg are already
returned for all origins. only change is to set ifindex, which is
not initialized for all error origins.
In both cases, only generate the pktinfo message if an ifindex is
known. This is not the case for ACK timestamps.
The difference between the protocol families is probably a historical
accident as a result of the different conditions for generating cmsg
in the relevant ip(v6)_recv_error function:
ipv4: if (serr->ee.ee_origin == SO_EE_ORIGIN_ICMP) {
ipv6: if (serr->ee.ee_origin != SO_EE_ORIGIN_LOCAL) {
At one time, this was the same test bar for the ICMP/ICMP6
distinction. This is no longer true.
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Changes
v1 -> v2
large rewrite
- integrate with existing pktinfo cmsg generation code
- on ipv4: only send with new flag, to maintain legacy behavior
- on ipv6: send at most a single pktinfo cmsg
- on ipv6: initialize fields if not yet initialized
The recv cmsg interfaces are also relevant to the discussion of
whether looping packet headers is problematic. For v6, cmsgs that
identify many headers are already returned. This patch expands
that to v4. If it sounds reasonable, I will follow with patches
1. request timestamps without payload with SOF_TIMESTAMPING_OPT_TSONLY
(http://patchwork.ozlabs.org/patch/366967/)
2. sysctl to conditionally drop all timestamps that have payload or
cmsg from users without CAP_NET_RAW.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
introduce new setsockopt() command:
setsockopt(sock, SOL_SOCKET, SO_ATTACH_BPF, &prog_fd, sizeof(prog_fd))
where prog_fd was received from syscall bpf(BPF_PROG_LOAD, attr, ...)
and attr->prog_type == BPF_PROG_TYPE_SOCKET_FILTER
setsockopt() calls bpf_prog_get() which increments refcnt of the program,
so it doesn't get unloaded while socket is using the program.
The same eBPF program can be attached to multiple sockets.
User task exit automatically closes socket which calls sk_filter_uncharge()
which decrements refcnt of eBPF program
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
introduce program type BPF_PROG_TYPE_SOCKET_FILTER that is used
for attaching programs to sockets where ctx == skb.
add verifier checks for ABS/IND instructions which can only be seen
in socket filters, therefore the check:
if (env->prog->aux->prog_type != BPF_PROG_TYPE_SOCKET_FILTER)
verbose("BPF_LD_ABS|IND instructions are only allowed in socket filters\n");
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following batch contains netfilter updates for net-next. Basically,
enhancements for xt_recent, skip zeroing of timer in conntrack, fix
linking problem with recent redirect support for nf_tables, ipset
updates and a couple of cleanups. More specifically, they are:
1) Rise maximum number per IP address to be remembered in xt_recent
while retaining backward compatibility, from Florian Westphal.
2) Skip zeroing timer area in nf_conn objects, also from Florian.
3) Inspect IPv4 and IPv6 traffic from the bridge to allow filtering using
using meta l4proto and transport layer header, from Alvaro Neira.
4) Fix linking problems in the new redirect support when CONFIG_IPV6=n
and IP6_NF_IPTABLES=n.
And ipset updates from Jozsef Kadlecsik:
5) Support updating element extensions when the set is full (fixes
netfilter bugzilla id 880).
6) Fix set match with 32-bits userspace / 64-bits kernel.
7) Indicate explicitly when /0 networks are supported in ipset.
8) Simplify cidr handling for hash:*net* types.
9) Allocate the proper size of memory when /0 networks are supported.
10) Explicitly add padding elements to hash:net,net and hash:net,port,
because the elements must be u32 sized for the used hash function.
Jozsef is also cooking ipset RCU conversion which should land soon if
they reach the merge window in time.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sven-Haegar Koch reported the issue:
sims:~# iptables -A OUTPUT -m set --match-set testset src -j ACCEPT
iptables: Invalid argument. Run `dmesg' for more information.
In syslog:
x_tables: ip_tables: set.3 match: invalid size 48 (kernel) != (user) 32
which was introduced by the counter extension in ipset.
The patch fixes the alignment issue with introducing a new set match
revision with the fixed underlying 'struct ip_set_counter_match'
structure.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
To allow brport device to return current brport flags set on port. Add
returned flags to nested IFLA_PROTINFO netlink msg built in dflt getlink.
With this change, netlink msg returned for bridge_getlink contains the port's
offloaded flag settings (the port's SELF settings).
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current hwmode settings are "vepa" or "veb". These are for NIC interfaces
with basic bridging function offloaded to HW. Add new "swdev" for full
switch device offloads.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This policy flag controls syncing of learned FDB entries to bridge's FDB. If
on, FDB entries learned on bridge port device will be synced. If off, device
may still learn new FDB entries but they will not be synced with bridge's FDB.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the swdev device learns a new mac/vlan on a port, it sends some async
notification to the driver and the driver installs an FDB in the device.
To give a holistic system view, the learned mac/vlan should be reflected
in the bridge's FBD table, so the user, using normal iproute2 cmds, can view
what is currently learned by the device. This API on the bridge driver gives
a way for the swdev driver to install an FBD entry in the bridge FBD table.
(And remove one).
This is equivalent to the device running these cmds:
bridge fdb [add|del] <mac> dev <dev> vid <vlan id> master
This patch needs some extra eyeballs for review, in paricular around the
locking and contexts.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To notify switch driver of change in STP state of bridge port, add new
.ndo op and provide switchdev wrapper func to call ndo op. Use it in bridge
code then.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netdevice represents a port in a switch, it will expose
IFLA_PHYS_SWITCH_ID value via rtnl. Two netdevices with the same value
belong to one physical switch.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The goal of this is to provide a possibility to support various switch
chips. Drivers should implement relevant ndos to do so. Now there is
only one ndo defined:
- for getting physical switch id is in place.
Note that user can use random port netdevice to access the switch.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So this can be reused for identification of other "items" as well.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver fixes from Greg KH:
"Here are some staging and IIO driver fixes for 3.18-rc7 that resolve a
number of reported issues, and a new device id for a staging wireless
driver.
All of these have been in linux-next"
* tag 'staging-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: Add new device ID for DLink GO-USB-N150
staging: r8188eu: Fix scheduling while atomic error introduced in commit fadbe0cd
iio: accel: bmc150: set low default thresholds
iio: accel: bmc150: Fix iio_event_spec direction
iio: accel: bmc150: Send x, y and z motion separately
iio: accel: bmc150: Error handling when mode set fails
iio: gyro: bmg160: Fix iio_event_spec direction
iio: gyro: bmg160: Send x, y and z motion separately
iio: gyro: bmg160: Don't let interrupt mode to be open drain
iio: gyro: bmg160: Error handling when mode set fails
iio: adc: men_z188_adc: Add terminating entry for men_z188_ids
iio: accel: kxcjk-1013: Fix kxcjk10013_set_range
iio: Fix IIO_EVENT_CODE_EXTRACT_DIR bit mask
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"No excitement, here are only minor fixes: an endian fix for the new
DSD format we added in 3.18, a fix for HP mute LED, and a fix for
Native Instrument quirk"
* tag 'sound-3.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pcm: Add big-endian DSD sample formats and fix XMOS DSD sample format
ALSA: hda - One more HP machine needs to change mute led quirk
ALSA: usb-audio: Use snd_usb_ctl_msg() for Native Instruments quirk
|
|
Pull networking fixes from David Miller:
"Several small fixes here:
1) Don't crash in tg3 driver when the number of tx queues has been
configured to be different from the number of rx queues. From
Thadeu Lima de Souza Cascardo.
2) VLAN filter not disabled properly in promisc mode in ixgbe driver,
from Vlad Yasevich.
3) Fix OOPS on dellink op in VTI tunnel driver, from Xin Long.
4) IPV6 GRE driver WCCP code checks skb->protocol for ETH_P_IP
instead of ETH_P_IPV6, whoops. From Yuri Chislov.
5) Socket matching in ping driver is buggy when packet AF does not
match socket's AF. Fix from Jane Zhou.
6) Fix checksum calculation errors in VXLAN due to where the
udp_tunnel6_xmit_skb() helper gets it's saddr/daddr from. From
Alexander Duyck.
7) Fix 5G detection problem in rtlwifi driver, from Larry Finger.
8) Fix NULL deref in tcp_v{4,6}_send_reset, from Eric Dumazet.
9) Various missing netlink attribute verifications in bridging code,
from Thomas Graf.
10) tcp_recvmsg() unconditionally calls ipv4 ip_recv_error even for
ipv6 sockets, whoops. Fix from Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
net-timestamp: make tcp_recvmsg call ipv6_recv_error for AF_INET6 socks
bridge: Sanitize IFLA_EXT_MASK for AF_BRIDGE:RTM_GETLINK
bridge: Add missing policy entry for IFLA_BRPORT_FAST_LEAVE
net: Check for presence of IFLA_AF_SPEC
net: Validate IFLA_BRIDGE_MODE attribute length
bridge: Validate IFLA_BRIDGE_FLAGS attribute length
stmmac: platform: fix default values of the filter bins setting
net/mlx4_core: Limit count field to 24 bits in qp_alloc_res
net: dsa: bcm_sf2: reset switch prior to initialization
net: dsa: bcm_sf2: fix unmapping registers in case of errors
tg3: fix ring init when there are more TX than RX channels
tcp: fix possible NULL dereference in tcp_vX_send_reset()
rtlwifi: Change order in device startup
rtlwifi: rtl8821ae: Fix 5G detection problem
Revert "netfilter: conntrack: fix race in __nf_conntrack_confirm against get_next_corpse"
vxlan: Fix boolean flip in VXLAN_F_UDP_ZERO_CSUM6_[TX|RX]
ip6_udp_tunnel: Fix checksum calculation
net-timestamp: Fix a documentation typo
net/ping: handle protocol mismatching scenario
af_packet: fix sparse warning
...
|
|
This resolves linking problems with CONFIG_IPV6=n:
net/built-in.o: In function `redirect_tg6':
xt_REDIRECT.c:(.text+0x6d021): undefined reference to `nf_nat_redirect_ipv6'
Reported-by: Andreas Ruprecht <rupran@einserver.de>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
This patch exports the functions nft_reject_iphdr_validate and
nft_reject_ip6hdr_validate to use it in follow up patches.
These functions check if the IPv4/IPv6 header is correct.
Signed-off-by: Alvaro Neira Ayuso <alvaroneay@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
add a __nfct_init_offset annotation member to struct nf_conn to make
it clear which members are covered by the memset when the conntrack
is allocated.
This avoids zeroing timer_list and ct_net; both are already inited
explicitly.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
TCP timestamping introduced MSG_ERRQUEUE handling for TCP sockets.
If the socket is of family AF_INET6, call ipv6_recv_error instead
of ip_recv_error.
This change is more complex than a single branch due to the loadable
ipv6 module. It reuses a pre-existing indirect function call from
ping. The ping code is safe to call, because it is part of the core
ipv6 module and always present when AF_INET6 sockets are active.
Fixes: 4ed2d765 (net-timestamp: TCP timestamping)
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
It may also be worthwhile to add WARN_ON_ONCE(sk->family == AF_INET6)
to ip_recv_error.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Third set of IIO fixes for the 3.18 cycle.
Most of these are fairly standard little fixes, a bmc150 and bmg160 patch
is to make an ABI change to indicated a specific axis in an event rather
than the generic option in the original drivers. As both of these drivers
are new in this cycle it would be ideal to push this minor change through
even though it isn't strictly a fix. A couple of other 'fixes' change
defaults for some settings on these new drivers to more intuitive calues.
Looks like some useful feedback has been coming in for this driver
since it was applied.
* IIO_EVENT_CODE_EXTRACT_DIR bit mask was wrong and has been for a while
0xCF clearly doesn't give a contiguous bitmask.
* kxcjk-1013 range setting was failing to mask out the previous value
in the register and hence was 'enable only'.
* men_z188 device id table wasn't null terminated.
* bmg160 and bmc150 both failed to correctly handling an error in mode
setting.
* bmg160 and bmc150 both had a bug in setting the event direction in the
event spec (leads to an attribute name being incorrect)
* bmg160 defaulted to an open drain output for the interrupt - as a default
this obviously only works with some interrupt chips - hence change the
default to push-pull (note this is a new driver so we aren't going to
cause any regressions with this change).
* bmc150 had an unintuitive default for the rate of change (motion detector)
so change it to 0 (new driver so change of default won't cause any
regressions).
|
|
This function does the work to update a checksum field as part of
remote checksum offload.
remcsum_adjust does the following:
1) Subtract out the calculated checksum from the beginning of the
packet (ptr arg) to the start offset.
2) Adjust the checksum field indicated by offset based on the modified
checksum value from above step.
3) Return the difference in the old checksum field value and the
new one. The caller will use this to update skb->csum and NAPI csum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 85c8555ff0 ("KVM: check for !is_zero_pfn() in
kvm_is_mmio_pfn()") and renames the function to kvm_is_reserved_pfn.
The problem being addressed by the patch above was that some ARM code
based the memory mapping attributes of a pfn on the return value of
kvm_is_mmio_pfn(), whose name indeed suggests that such pfns should
be mapped as device memory.
However, kvm_is_mmio_pfn() doesn't do quite what it says on the tin,
and the existing non-ARM users were already using it in a way which
suggests that its name should probably have been 'kvm_is_reserved_pfn'
from the beginning, e.g., whether or not to call get_page/put_page on
it etc. This means that returning false for the zero page is a mistake
and the patch above should be reverted.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Ben Herrenschmidt:
"This series fix a nasty issue with radeon adapters on powerpc servers,
it's all CC'ed stable and has the relevant maintainers ack's/reviews.
Basically, some (radeon) adapters have issues with MSI addresses above
1T (only support 40-bits). We had powerpc specific quirk but it only
listed a specific revision of an adapter that we shipped with our
machines and didn't properly handle the audio function which some
distros enable nowadays.
So we made the quirk generic and fixed both the graphic and audio
drivers properly to use it.
Without that, ppc64 server machines will crash at boot with a radeon
adapter.
Note: This has been brewing for a while, it just needed a last respin
which got delayed due to us moving ozlabs to a new location in town
and other such things taking priority"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pci: Remove unused force_32bit_msi quirk
powerpc/pseries: Honor the generic "no_64bit_msi" flag
powerpc/powernv: Honor the generic "no_64bit_msi" flag
sound/radeon: Move 64-bit MSI quirk from arch to driver
gpu/radeon: Set flag to indicate broken 64-bit MSI
PCI/MSI: Add device flag indicating that 64-bit MSIs don't work
ALSA: hda - Limit 40bit DMA for AMD HDMI controllers
|
|
https://git.linaro.org/people/mike.turquette/linux
Pull clock fixes from Mike Turquette:
"The fixes for the clock framework are all regressions in drivers, plus
a single fix in one of the basic clock templates. No fixes to the
core this time around.
As with most clock driver fixes these run the gamut from fixing a
build warning to fixing wrecked memory timings, with a little USB
tossed in for fun"
* tag 'clk-fixes-for-linus' of https://git.linaro.org/people/mike.turquette/linux:
clk: pxa: fix pxa27x CCCR bit usage
clk-divider: Fix READ_ONLY when divider > 1
clk: qcom: Fix duplicate rbcpr clock name
clk: at91: usb: fix at91sam9x5 recalc, round and set rate
clk: at91: usb: fix at91rm9200 round and set rate
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
More work from Al Viro to move away from modifying iovecs
by using iov_iter instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tipc_netlink.h is the user-space header for the new netlink api. It
was accidentally left out of the uapi Kbuild list when the api was
added.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Should be u16. So fix it to kill the sparse warning.
Fixes: c7e2b9689ef8136 "sched: introduce vlan action"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
netfilter/ipvs updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, this includes the NAT redirection support for nf_tables, the
cgroup support for nft meta and conntrack zone support for the connlimit
match. Coming after those, a bunch of sparse warning fixes, missing
netns bits and cleanups. More specifically, they are:
1) Prepare IPv4 and IPv6 NAT redirect code to use it from nf_tables,
patches from Arturo Borrero.
2) Introduce the nf_tables redir expression, from Arturo Borrero.
3) Remove an unnecessary assignment in ip_vs_xmit/__ip_vs_get_out_rt().
Patch from Alex Gartrell.
4) Add nft_log_dereference() macro to the nf_log infrastructure, patch
from Marcelo Leitner.
5) Add some extra validation when registering logger families, also
from Marcelo.
6) Some spelling cleanups from stephen hemminger.
7) Fix sparse warning in nf_logger_find_get().
8) Add cgroup support to nf_tables meta, patch from Ana Rey.
9) A Kconfig fix for the new redir expression and fix sparse warnings in
the new redir expression.
10) Fix several sparse warnings in the netfilter tree, from
Florian Westphal.
11) Reduce verbosity when OOM in nfnetlink_log. User can basically do
nothing when this situation occurs.
12) Add conntrack zone support to xt_connlimit, again from Florian.
13) Add netnamespace support to the h323 conntrack helper, contributed
by Vasily Averin.
14) Remove unnecessary nul-pointer checks before free_percpu() and
module_put(), from Markus Elfring.
15) Use pr_fmt in nfnetlink_log, again patch from Marcelo Leitner.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver is very similar to the macvlan driver except that it
uses L3 on the frame to determine the logical interface while
functioning as packet dispatcher. It inherits L2 of the master
device hence the packets on wire will have the same L2 for all
the packets originating from all virtual devices off of the same
master device.
This driver was developed keeping the namespace use-case in
mind. Hence most of the examples given here take that as the
base setup where main-device belongs to the default-ns and
virtual devices are assigned to the additional namespaces.
The device operates in two different modes and the difference
in these two modes in primarily in the TX side.
(a) L2 mode : In this mode, the device behaves as a L2 device.
TX processing upto L2 happens on the stack of the virtual device
associated with (namespace). Packets are switched after that
into the main device (default-ns) and queued for xmit.
RX processing is simple and all multicast, broadcast (if
applicable), and unicast belonging to the address(es) are
delivered to the virtual devices.
(b) L3 mode : In this mode, the device behaves like a L3 device.
TX processing upto L3 happens on the stack of the virtual device
associated with (namespace). Packets are switched to the
main-device (default-ns) for the L2 processing. Hence the routing
table of the default-ns will be used in this mode.
RX processins is somewhat similar to the L2 mode except that in
this mode only Unicast packets are delivered to the virtual device
while main-dev will handle all other packets.
The devices can be added using the "ip" command from the iproute2
package -
ip link add link <master> <virtual> type ipvlan mode [ l2 | l3 ]
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Laurent Chavey <chavey@google.com>
Cc: Tim Hockin <thockin@google.com>
Cc: Brandon Philips <brandon.philips@coreos.com>
Cc: Pavel Emelianov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
to msghdr
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
... and kill skb_copy_datagram_iovec()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
no users left
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
This can be set by quirks/drivers to be used by the architecture code
that assigns the MSI addresses.
We additionally add verification in the core MSI code that the values
assigned by the architecture do satisfy the limitation in order to fail
gracefully if they don't (ie. the arch hasn't been updated to deal with
that quirk yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Pull percpu fix from Tejun Heo:
"This contains one patch to fix a race condition which can lead to
percpu_ref using a percpu pointer which is corrupted with a set DEAD
bit. The bug was introduced while separating out the ATOMIC mode flag
from the DEAD flag. The fix is pretty straight forward.
I just committed the patch to the percpu tree but am sending out the
pull request early as I'll be on vacation for a week. The patch
should be fairly safe and while the latency will be higher I'll be
checking emails"
* 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu-ref: fix DEAD flag contamination of percpu pointer
|
|
While decoupling ATOMIC and DEAD flags, f47ad4578461 ("percpu_ref:
decouple switching to percpu mode and reinit") updated
__ref_is_percpu() so that it only tests ATOMIC flag to determine
whether the ref is in percpu mode or not; however, while DEAD implies
ATOMIC, the two flags are set separately during percpu_ref_kill() and
if __ref_is_percpu() races percpu_ref_kill(), it may see DEAD w/o
ATOMIC. Because __ref_is_percpu() returns @ref->percpu_count_ptr
value verbatim as the percpu pointer after testing ATOMIC, the pointer
may now be contaminated with the DEAD flag.
This can be fixed by clearing the flag bits before returning the
pointer which was the fix proposed by Shaohua; however, as DEAD
implies ATOMIC, we can just test for both flags at once and avoid the
explicit masking.
Update __ref_is_percpu() so that it tests that both ATOMIC and DEAD
are clear before returning @ref->percpu_count_ptr as the percpu
pointer.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-Reviewed-by: Shaohua Li <shli@kernel.org>
Link: http://lkml.kernel.org/r/995deb699f5b873c45d667df4add3b06f73c2c25.1416638887.git.shli@kernel.org
Fixes: f47ad4578461 ("percpu_ref: decouple switching to percpu mode and reinit")
|
|
Conflicts:
drivers/net/ieee802154/fakehard.c
A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.
Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Fix BUG when decrypting empty packets in mac80211, from Ronald Wahl.
2) nf_nat_range is not fully initialized and this is copied back to
userspace, from Daniel Borkmann.
3) Fix read past end of b uffer in netfilter ipset, also from Dan
Carpenter.
4) Signed integer overflow in ipv4 address mask creation helper
inet_make_mask(), from Vincent BENAYOUN.
5) VXLAN, be2net, mlx4_en, and qlcnic need ->ndo_gso_check() methods to
properly describe the device's capabilities, from Joe Stringer.
6) Fix memory leaks and checksum miscalculations in openvswitch, from
Pravin B SHelar and Jesse Gross.
7) FIB rules passes back ambiguous error code for unreachable routes,
making behavior confusing for userspace. Fix from Panu Matilainen.
8) ieee802154fake_probe() doesn't release resources properly on error,
from Alexey Khoroshilov.
9) Fix skb_over_panic in add_grhead(), from Daniel Borkmann.
10) Fix access of stale slave pointers in bonding code, from Nikolay
Aleksandrov.
11) Fix stack info leak in PPP pptp code, from Mathias Krause.
12) Cure locking bug in IPX stack, from Jiri Bohac.
13) Revert SKB fclone memory freeing optimization that is racey and can
allow accesses to freed up memory, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (71 commits)
tcp: Restore RFC5961-compliant behavior for SYN packets
net: Revert "net: avoid one atomic operation in skb_clone()"
virtio-net: validate features during probe
cxgb4 : Fix DCB priority groups being returned in wrong order
ipx: fix locking regression in ipx_sendmsg and ipx_recvmsg
openvswitch: Don't validate IPv6 label masks.
pptp: fix stack info leak in pptp_getname()
brcmfmac: don't include linux/unaligned/access_ok.h
cxgb4i : Don't block unload/cxgb4 unload when remote closes TCP connection
ipv6: delete protocol and unregister rtnetlink when cleanup
net/mlx4_en: Add VXLAN ndo calls to the PF net device ops too
bonding: fix curr_active_slave/carrier with loadbalance arp monitoring
mac80211: minstrel_ht: fix a crash in rate sorting
vxlan: Inline vxlan_gso_check().
can: m_can: update to support CAN FD features
can: m_can: fix incorrect error messages
can: m_can: add missing delay after setting CCCR_INIT bit
can: m_can: fix not set can_dlc for remote frame
can: m_can: fix possible sleep in napi poll
can: m_can: add missing message RAM initialization
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This batch ended up as a relatively high volume due to pending ASoC
fixes. But most of fixes there are trivial and/or device- specific
fixes and quirks, so safe to apply. The only (ASoC) core fixes are
the DPCM race fix and the machine-driver matching fix for
componentization"
* tag 'sound-3.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - fix the mic mute led problem for Latitude E5550
ALSA: hda - move DELL_WMI_MIC_MUTE_LED to the tail in the quirk chain
ASoC: wm_adsp: Avoid attempt to free buffers that might still be in use
ALSA: usb-audio: Set the Control Selector to SU_SELECTOR_CONTROL for UAC2
ALSA: usb-audio: Add ctrl message delay quirk for Marantz/Denon devices
ASoC: sgtl5000: Fix SMALL_POP bit definition
ASoC: cs42l51: re-hook of_match_table pointer
ASoC: rt5670: change dapm routes of PLL connection
ASoC: rt5670: correct the incorrect default values
ASoC: samsung: Add MODULE_DEVICE_TABLE for Snow
ASoC: max98090: Correct pclk divisor settings
ASoC: dpcm: Fix race between FE/BE updates and trigger
ASoC: Fix snd_soc_find_dai() matching component by name
ASoC: rsnd: remove unsupported PAUSE flag
ASoC: fsi: remove unsupported PAUSE flag
ASoC: rt5645: Mark RT5645_TDM_CTRL_3 as readable
ASoC: rockchip-i2s: fix infinite loop in rockchip_snd_rxctrl
ASoC: es8328-i2c: Fix i2c_device_id name field in es8328_id
ASoC: fsl_asrc: Add reg_defaults for regmap to fix kernel dump
|
